From 0a2356572b1910cc977f4ccf3c9ee1ecab08327a Mon Sep 17 00:00:00 2001 From: Viresh Kumar Date: Fri, 5 Aug 2011 15:32:42 +0530 Subject: dmaengine/amba-pl08x: Pass flow controller information with slave channel data At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow controller for DMA transfer. Currently DMA controller driver didn't support peripheral flow controller configurations. This patch adds device_fc field in struct pl08x_channel_data, which will be used only for slave transfers and is not used in case of mem2mem transfers. Signed-off-by: Viresh Kumar Acked-by: Linus Walleij Signed-off-by: Vinod Koul --- drivers/dma/amba-pl08x.c | 61 +++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 53 insertions(+), 8 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c index f70aa574c58f..a59c3c47286c 100644 --- a/drivers/dma/amba-pl08x.c +++ b/drivers/dma/amba-pl08x.c @@ -66,11 +66,6 @@ * after the final transfer signalled by LBREQ or LSREQ. The DMAC * will then move to the next LLI entry. * - * Only the former works sanely with scatter lists, so we only implement - * the DMAC flow control method. However, peripherals which use the LBREQ - * and LSREQ signals (eg, MMCI) are unable to use this mode, which through - * these hardware restrictions prevents them from using scatter DMA. - * * Global TODO: * - Break out common code from arch/arm/mach-s3c64xx and share */ @@ -617,6 +612,49 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x, mbus == &bd.srcbus ? "src" : "dst", sbus == &bd.srcbus ? "src" : "dst"); + /* + * Zero length is only allowed if all these requirements are met: + * - flow controller is peripheral. + * - src.addr is aligned to src.width + * - dst.addr is aligned to dst.width + * + * sg_len == 1 should be true, as there can be two cases here: + * - Memory addresses are contiguous and are not scattered. Here, Only + * one sg will be passed by user driver, with memory address and zero + * length. We pass this to controller and after the transfer it will + * receive the last burst request from peripheral and so transfer + * finishes. + * + * - Memory addresses are scattered and are not contiguous. Here, + * Obviously as DMA controller doesn't know when a lli's transfer gets + * over, it can't load next lli. So in this case, there has to be an + * assumption that only one lli is supported. Thus, we can't have + * scattered addresses. + */ + if (!bd.remainder) { + u32 fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >> + PL080_CONFIG_FLOW_CONTROL_SHIFT; + if (!((fc >= PL080_FLOW_SRC2DST_DST) && + (fc <= PL080_FLOW_SRC2DST_SRC))) { + dev_err(&pl08x->adev->dev, "%s sg len can't be zero", + __func__); + return 0; + } + + if ((bd.srcbus.addr % bd.srcbus.buswidth) || + (bd.srcbus.addr % bd.srcbus.buswidth)) { + dev_err(&pl08x->adev->dev, + "%s src & dst address must be aligned to src" + " & dst width if peripheral is flow controller", + __func__); + return 0; + } + + cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth, + bd.dstbus.buswidth, 0); + pl08x_fill_lli_for_desc(&bd, num_llis++, 0, cctl); + } + /* * Send byte by byte for following cases * - Less than a bus width available @@ -1250,7 +1288,7 @@ static struct dma_async_tx_descriptor *pl08x_prep_slave_sg( struct pl08x_dma_chan *plchan = to_pl08x_chan(chan); struct pl08x_driver_data *pl08x = plchan->host; struct pl08x_txd *txd; - int ret; + int ret, tmp; /* * Current implementation ASSUMES only one sg @@ -1284,12 +1322,10 @@ static struct dma_async_tx_descriptor *pl08x_prep_slave_sg( txd->len = sgl->length; if (direction == DMA_TO_DEVICE) { - txd->ccfg |= PL080_FLOW_MEM2PER << PL080_CONFIG_FLOW_CONTROL_SHIFT; txd->cctl = plchan->dst_cctl; txd->src_addr = sgl->dma_address; txd->dst_addr = plchan->dst_addr; } else if (direction == DMA_FROM_DEVICE) { - txd->ccfg |= PL080_FLOW_PER2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT; txd->cctl = plchan->src_cctl; txd->src_addr = plchan->src_addr; txd->dst_addr = sgl->dma_address; @@ -1299,6 +1335,15 @@ static struct dma_async_tx_descriptor *pl08x_prep_slave_sg( return NULL; } + if (plchan->cd->device_fc) + tmp = (direction == DMA_TO_DEVICE) ? PL080_FLOW_MEM2PER_PER : + PL080_FLOW_PER2MEM_PER; + else + tmp = (direction == DMA_TO_DEVICE) ? PL080_FLOW_MEM2PER : + PL080_FLOW_PER2MEM; + + txd->ccfg |= tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT; + ret = pl08x_prep_channel_resources(plchan, txd); if (ret) return NULL; -- cgit v1.2.3