From 43f847d0b9540dd1de4cfd626448fb4294422874 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 5 Aug 2019 10:58:44 +0200 Subject: drm/pl111: Support grayscale Migrating the TI nspire calculators to use the PL111 driver for framebuffer requires grayscale support for the elder panel which uses 8bit grayscale only. DRM does not support 8bit grayscale framebuffers in memory, but by defining the bus format to be MEDIA_BUS_FMT_Y8_1X8 we can get the hardware to turn on a grayscaling feature and convert the RGB framebuffer to grayscale for us. Cc: Daniel Tang Cc: Fabian Vogt Tested-by: Fabian Vogt Acked-by: Sam Ravnborg Signed-off-by: Linus Walleij Link: https://patchwork.freedesktop.org/patch/msgid/20190805085847.25554-2-linus.walleij@linaro.org --- drivers/gpu/drm/pl111/pl111_display.c | 29 +++++++++++++++++++++++++++-- 1 file changed, 27 insertions(+), 2 deletions(-) (limited to 'drivers/gpu/drm/pl111') diff --git a/drivers/gpu/drm/pl111/pl111_display.c b/drivers/gpu/drm/pl111/pl111_display.c index 9a153125e5d2..024771a4083e 100644 --- a/drivers/gpu/drm/pl111/pl111_display.c +++ b/drivers/gpu/drm/pl111/pl111_display.c @@ -128,6 +128,7 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe, struct drm_framebuffer *fb = plane->state->fb; struct drm_connector *connector = priv->connector; struct drm_bridge *bridge = priv->bridge; + bool grayscale = false; u32 cntl; u32 ppl, hsw, hfp, hbp; u32 lpp, vsw, vfp, vbp; @@ -187,6 +188,20 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe, if (connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE) tim2 |= TIM2_IPC; + + if (connector->display_info.num_bus_formats == 1 && + connector->display_info.bus_formats[0] == + MEDIA_BUS_FMT_Y8_1X8) + grayscale = true; + + /* + * The AC pin bias frequency is set to max count when using + * grayscale so at least once in a while we will reverse + * polarity and get rid of any DC built up that could + * damage the display. + */ + if (grayscale) + tim2 |= TIM2_ACB_MASK; } if (bridge) { @@ -218,8 +233,18 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe, writel(0, priv->regs + CLCD_TIM3); - /* Hard-code TFT panel */ - cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDVCOMP(1); + /* + * Detect grayscale bus format. We do not support a grayscale mode + * toward userspace, instead we expose an RGB24 buffer and then the + * hardware will activate its grayscaler to convert to the grayscale + * format. + */ + if (grayscale) + cntl = CNTL_LCDEN | CNTL_LCDMONO8; + else + /* Else we assume TFT display */ + cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDVCOMP(1); + /* On the ST Micro variant, assume all 24 bits are connected */ if (priv->variant->st_bitmux_control) cntl |= CNTL_ST_CDWID_24; -- cgit v1.2.3