From a1f17a872bc7b1cb7efdd5486a2963e88a536e61 Mon Sep 17 00:00:00 2001 From: Libin Yang Date: Wed, 4 Nov 2009 14:55:18 +0800 Subject: USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer The following patch in the driver is required to avoid USB 1.1 device failures that may occur due to requests from USB OHCI controllers may be overwritten if the latency for any pending request by the USB controller is very long (in the range of milliseconds). Signed-off-by: Libin Yang Cc: David Brownell Cc: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-hcd.c | 5 +++++ drivers/usb/host/ohci-pci.c | 20 ++++++++++++++++++++ drivers/usb/host/ohci-q.c | 18 ++++++++++++------ drivers/usb/host/ohci.h | 9 +++++++++ 4 files changed, 46 insertions(+), 6 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 78bb7710f36d..24eb74781919 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -87,6 +87,7 @@ static int ohci_restart (struct ohci_hcd *ohci); #ifdef CONFIG_PCI static void quirk_amd_pll(int state); static void amd_iso_dev_put(void); +static void sb800_prefetch(struct ohci_hcd *ohci, int on); #else static inline void quirk_amd_pll(int state) { @@ -96,6 +97,10 @@ static inline void amd_iso_dev_put(void) { return; } +static inline void sb800_prefetch(struct ohci_hcd *ohci, int on) +{ + return; +} #endif diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index d2ba04dd785e..b8a1148f248e 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -177,6 +177,13 @@ static int ohci_quirk_amd700(struct usb_hcd *hcd) return 0; pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + + /* SB800 needs pre-fetch fix */ + if ((rev >= 0x40) && (rev <= 0x4f)) { + ohci->flags |= OHCI_QUIRK_AMD_PREFETCH; + ohci_dbg(ohci, "enabled AMD prefetch quirk\n"); + } + if ((rev > 0x3b) || (rev < 0x30)) { pci_dev_put(amd_smbus_dev); amd_smbus_dev = NULL; @@ -262,6 +269,19 @@ static void amd_iso_dev_put(void) } +static void sb800_prefetch(struct ohci_hcd *ohci, int on) +{ + struct pci_dev *pdev; + u16 misc; + + pdev = to_pci_dev(ohci_to_hcd(ohci)->self.controller); + pci_read_config_word(pdev, 0x50, &misc); + if (on == 0) + pci_write_config_word(pdev, 0x50, misc & 0xfcff); + else + pci_write_config_word(pdev, 0x50, misc | 0x0300); +} + /* List of quirks for OHCI */ static const struct pci_device_id ohci_pci_quirks[] = { { diff --git a/drivers/usb/host/ohci-q.c b/drivers/usb/host/ohci-q.c index 16fecb8ecc39..35288bcae0db 100644 --- a/drivers/usb/host/ohci-q.c +++ b/drivers/usb/host/ohci-q.c @@ -49,9 +49,12 @@ __acquires(ohci->lock) switch (usb_pipetype (urb->pipe)) { case PIPE_ISOCHRONOUS: ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs--; - if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0 - && quirk_amdiso(ohci)) - quirk_amd_pll(1); + if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0) { + if (quirk_amdiso(ohci)) + quirk_amd_pll(1); + if (quirk_amdprefetch(ohci)) + sb800_prefetch(ohci, 0); + } break; case PIPE_INTERRUPT: ohci_to_hcd(ohci)->self.bandwidth_int_reqs--; @@ -680,9 +683,12 @@ static void td_submit_urb ( data + urb->iso_frame_desc [cnt].offset, urb->iso_frame_desc [cnt].length, urb, cnt); } - if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0 - && quirk_amdiso(ohci)) - quirk_amd_pll(0); + if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0) { + if (quirk_amdiso(ohci)) + quirk_amd_pll(0); + if (quirk_amdprefetch(ohci)) + sb800_prefetch(ohci, 1); + } periodic = ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs++ == 0 && ohci_to_hcd(ohci)->self.bandwidth_int_reqs == 0; break; diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h index 222011f6172c..5bf15fed0d9f 100644 --- a/drivers/usb/host/ohci.h +++ b/drivers/usb/host/ohci.h @@ -402,6 +402,7 @@ struct ohci_hcd { #define OHCI_QUIRK_FRAME_NO 0x80 /* no big endian frame_no shift */ #define OHCI_QUIRK_HUB_POWER 0x100 /* distrust firmware power/oc setup */ #define OHCI_QUIRK_AMD_ISO 0x200 /* ISO transfers*/ +#define OHCI_QUIRK_AMD_PREFETCH 0x400 /* pre-fetch for ISO transfer */ // there are also chip quirks/bugs in init logic struct work_struct nec_work; /* Worker for NEC quirk */ @@ -433,6 +434,10 @@ static inline int quirk_amdiso(struct ohci_hcd *ohci) { return ohci->flags & OHCI_QUIRK_AMD_ISO; } +static inline int quirk_amdprefetch(struct ohci_hcd *ohci) +{ + return ohci->flags & OHCI_QUIRK_AMD_PREFETCH; +} #else static inline int quirk_nec(struct ohci_hcd *ohci) { @@ -446,6 +451,10 @@ static inline int quirk_amdiso(struct ohci_hcd *ohci) { return 0; } +static inline int quirk_amdprefetch(struct ohci_hcd *ohci) +{ + return 0; +} #endif /* convert between an hcd pointer and the corresponding ohci_hcd */ -- cgit v1.2.3 From 18a77b5d237a67d2c621a46f5271a3b51da1b380 Mon Sep 17 00:00:00 2001 From: Henry Gebhardt Date: Wed, 4 Nov 2009 11:19:28 +0100 Subject: USB: cdc_acm: Fix race condition when opening tty If acm_rx_tasklet() gets called before tty_port_block_til_ready() returns, then bulk IN urbs may not be sent. This fixes it. Signed-off-by: Henry Gebhardt Acked-by: Oliver Neukum Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index e3861b21e776..b72fa49eb257 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -609,9 +609,9 @@ static int acm_tty_open(struct tty_struct *tty, struct file *filp) acm->throttle = 0; - tasklet_schedule(&acm->urb_task); set_bit(ASYNCB_INITIALIZED, &acm->port.flags); rv = tty_port_block_til_ready(&acm->port, tty, filp); + tasklet_schedule(&acm->urb_task); done: mutex_unlock(&acm->mutex); err_out: -- cgit v1.2.3 From 051522bb47797f7168a617a0752d7ddc1a2f6f24 Mon Sep 17 00:00:00 2001 From: Francesco Lavra Date: Tue, 3 Nov 2009 10:53:07 +0000 Subject: USB: cdc_acm: Fix memory leak after hangup Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich: > Hello, > > i have the following problem with the cdc-acm - driver: > > I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400. > > If a disable the device (with the RFKill-Switch) while it is used by a > programm like ppp, the driver doesn't seem to correctly clean up the tty, > even after the program has been closed) > > The tty is still active (e.g. there still exists an entry in > /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device, > this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2 > and ttyACM3 will be used. > > This problem was introduced with the commit > 10077d4a6674f535abdbe25cdecb1202af7948f1 (before 2.6.31-rc1) and still > exists in 2.6.31. > > I was able the fix this problem with the following patch: > > diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c > index 2bfc41e..0970d2f 100644 > --- a/drivers/usb/class/cdc-acm.c > +++ b/drivers/usb/class/cdc-acm.c > @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty) > struct acm *acm = tty->driver_data; > tty_port_hangup(&acm->port); > acm_port_down(acm, 0); > + acm_tty_unregister(acm); > } I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I unplug it from the USB port during a PPP connection, the ppp daemon gets the hangup correctly (and closes the device), but the struct acm corresponding to the device disconnected is not freed. Hence reconnecting the device results in creation of /dev/ttyACM(x+1). The same happens when the system is hibernated during a PPP connection. This memory leak is due to the fact that when the tty is hung up, tty_port_close_start() returns always zero, and acm_tty_close() never reaches the point where acm_tty_unregister() is called. Here is a fix for this. Signed-off-by: Francesco Lavra Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index b72fa49eb257..e4eca7810bcf 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -686,15 +686,21 @@ static void acm_tty_close(struct tty_struct *tty, struct file *filp) /* Perform the closing process and see if we need to do the hardware shutdown */ - if (!acm || tty_port_close_start(&acm->port, tty, filp) == 0) + if (!acm) + return; + if (tty_port_close_start(&acm->port, tty, filp) == 0) { + mutex_lock(&open_mutex); + if (!acm->dev) { + tty_port_tty_set(&acm->port, NULL); + acm_tty_unregister(acm); + tty->driver_data = NULL; + } + mutex_unlock(&open_mutex); return; + } acm_port_down(acm, 0); tty_port_close_end(&acm->port, tty); - mutex_lock(&open_mutex); tty_port_tty_set(&acm->port, NULL); - if (!acm->dev) - acm_tty_unregister(acm); - mutex_unlock(&open_mutex); } static int acm_tty_write(struct tty_struct *tty, -- cgit v1.2.3 From d94c05e33d9212ee67b8d4998f984cc71df8168b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 3 Nov 2009 22:02:22 -0800 Subject: USB: xhci: Fix bug memory free after failed initialization. If the xHCI driver fails during the memory initialization, xhci->ir_set may not be a valid pointer. Check that it points to valid DMA'able memory before writing to that address during the memory freeing process. Signed-off-by: Sarah Sharp Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 1db4fea8c170..732580c6cbea 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -802,9 +802,11 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) int i; /* Free the Event Ring Segment Table and the actual Event Ring */ - xhci_writel(xhci, 0, &xhci->ir_set->erst_size); - xhci_write_64(xhci, 0, &xhci->ir_set->erst_base); - xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue); + if (xhci->ir_set) { + xhci_writel(xhci, 0, &xhci->ir_set->erst_size); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_base); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue); + } size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries); if (xhci->erst.entries) pci_free_consistent(pdev, size, -- cgit v1.2.3 From 2fa88daa6f299bfb83672c3b525d786ad03b4735 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 3 Nov 2009 22:02:24 -0800 Subject: USB: xhci: Fix TRB physical to virtual address translation. The trb_in_td() function in the xHCI driver is supposed to translate a physical transfer buffer request (TRB) into a virtual pointer to the ring segment that TRB is in. Unfortunately, a mistake in this function may cause endless loops as the driver searches through the linked list of ring segments over and over again. Fix a couple bugs that may lead to loops or bad output: 1. Bail out if we get a NULL pointer when translating the segment's private structure and the starting DMA address of the segment chunk. If this happens, we've been handed a starting TRB pointer from a different ring. 2. Make sure the function works when there's multiple segments in the ring. In the while loop to search through the ring segments, use the current segment variable (cur_seg), rather than the starting segment variable (start_seg) that is passed in. 3. Stop searching the ring if we've run through all the segments in the ring. Signed-off-by: Sarah Sharp Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 173c39c76489..821b7b4709de 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -864,9 +864,11 @@ static struct xhci_segment *trb_in_td( cur_seg = start_seg; do { + if (start_dma == 0) + return 0; /* We may get an event for a Link TRB in the middle of a TD */ end_seg_dma = xhci_trb_virt_to_dma(cur_seg, - &start_seg->trbs[TRBS_PER_SEGMENT - 1]); + &cur_seg->trbs[TRBS_PER_SEGMENT - 1]); /* If the end TRB isn't in this segment, this is set to 0 */ end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb); @@ -893,8 +895,9 @@ static struct xhci_segment *trb_in_td( } cur_seg = cur_seg->next; start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]); - } while (1); + } while (cur_seg != start_seg); + return 0; } /* -- cgit v1.2.3 From 5294bea40666db5c5d6c336b8e4e55d69fa576ca Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Wed, 4 Nov 2009 11:22:19 -0800 Subject: USB: xhci: Fix scratchpad deallocation. The scratchpad_free() function uses xhci->page_size to free some memory with pci_free_consistent(). However, the page_size is set to zero before the call, causing kernel oopses on driver unload. Call scratchpad_free() before setting xhci->page_size to zero. Signed-off-by: Sarah Sharp Acked-by: John Youn Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 732580c6cbea..b8fd270a8b0d 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -843,9 +843,9 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->dcbaa, xhci->dcbaa->dma); xhci->dcbaa = NULL; + scratchpad_free(xhci); xhci->page_size = 0; xhci->page_shift = 0; - scratchpad_free(xhci); } int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) -- cgit v1.2.3 From fca94748c5136ff390eadc443871b82f1f77dcd6 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Wed, 4 Nov 2009 11:35:53 -0500 Subject: USB: usbmon: fix bug in mon_buff_area_shrink This patch (as1299b) fixes a bug in an error-handling path of usbmon's binary interface. The storage area for URB data is divided into fixed-size blocks. If an URB's data can't be copied, the area reserved for it should be decreased to the size of the truncated information (rounded up to a block boundary). Rounding up the amount to be removed and subtracting it from the reserved size is definitely the wrong thing to do. Also, when the data for an isochronous URB can't be copied, we can still copy the isoc packet descriptors. In fact the current code does copy the descriptors, but then sets the capture length to 0 so they remain inaccessible. The capture length should be reduced to the length of the descriptors, not set to 0. Signed-off-by: Alan Stern Acked-by: Pete Zaitcev CC: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/mon/mon_bin.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/mon/mon_bin.c b/drivers/usb/mon/mon_bin.c index 9ed3e741bee1..10f3205798e8 100644 --- a/drivers/usb/mon/mon_bin.c +++ b/drivers/usb/mon/mon_bin.c @@ -348,12 +348,12 @@ static unsigned int mon_buff_area_alloc_contiguous(struct mon_reader_bin *rp, /* * Return a few (kilo-)bytes to the head of the buffer. - * This is used if a DMA fetch fails. + * This is used if a data fetch fails. */ static void mon_buff_area_shrink(struct mon_reader_bin *rp, unsigned int size) { - size = (size + PKT_ALIGN-1) & ~(PKT_ALIGN-1); + /* size &= ~(PKT_ALIGN-1); -- we're called with aligned size */ rp->b_cnt -= size; if (rp->b_in < size) rp->b_in += rp->b_size; @@ -433,6 +433,7 @@ static void mon_bin_event(struct mon_reader_bin *rp, struct urb *urb, unsigned int urb_length; unsigned int offset; unsigned int length; + unsigned int delta; unsigned int ndesc, lendesc; unsigned char dir; struct mon_bin_hdr *ep; @@ -537,8 +538,10 @@ static void mon_bin_event(struct mon_reader_bin *rp, struct urb *urb, if (length != 0) { ep->flag_data = mon_bin_get_data(rp, offset, urb, length); if (ep->flag_data != 0) { /* Yes, it's 0x00, not '0' */ - ep->len_cap = 0; - mon_buff_area_shrink(rp, length); + delta = (ep->len_cap + PKT_ALIGN-1) & ~(PKT_ALIGN-1); + ep->len_cap -= length; + delta -= (ep->len_cap + PKT_ALIGN-1) & ~(PKT_ALIGN-1); + mon_buff_area_shrink(rp, delta); } } else { ep->flag_data = data_tag; -- cgit v1.2.3 From ff854ce0b17161a86b5ae444c6cb0aa221720fab Mon Sep 17 00:00:00 2001 From: Zhang Le Date: Wed, 4 Nov 2009 23:22:59 +0800 Subject: USB: option.c: add support for D-Link DWM-162-U5 Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device has 4 interfaces, of which 1 is handled by storage and the other 3 by option driver. The device appears first as CD-only 05c6:2100 device and must be switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch. The MessageContent for usb_modeswitch.conf is: "55534243e0c26a85000000000000061b000000020000000000000000000000" Signed-off-by: Zhang Le Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index cd44c68954df..319aaf9725b3 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -308,6 +308,7 @@ static int option_resume(struct usb_serial *serial); #define DLINK_VENDOR_ID 0x1186 #define DLINK_PRODUCT_DWM_652 0x3e04 +#define DLINK_PRODUCT_DWM_652_U5 0xce16 #define QISDA_VENDOR_ID 0x1da5 #define QISDA_PRODUCT_H21_4512 0x4512 @@ -586,6 +587,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, + { USB_DEVICE(ALINK_VENDOR_ID, DLINK_PRODUCT_DWM_652_U5) }, /* Yes, ALINK_VENDOR_ID */ { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4523) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H20_4515) }, -- cgit v1.2.3