From a17b9e4c9c5e9c4da4385908af0377af11529266 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 18 Oct 2016 13:42:09 +0800 Subject: clk: sunxi-ng: sun6i-a31: Force AHB1 clock to use PLL6 as parent On the A31, the DMA engine only works if AHB1 is clocked from PLL6. In addition, the hstimer is clocked from AHB1, and if AHB1 is clocked from the CPU clock, and cpufreq is working, we get an unstable timer. Force the AHB1 clock to use PLL6 as its parent. Previously this was done in the device tree with the assigned-clocks and assigned-clocks-parent bindings. However with this new monolithic driver, the system critical clocks aren't exported through the device tree. The alternative is to force this setting in the driver before the clocks are registered. This is also done in newer versions of mainline U-boot. But people still using an older version, or even the vendor version, can still hit this issue. Hence the need to do it in the kernel as well. Reported-by: Hans de Goede Reported-by: Maxime Ripard Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks") Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- drivers/clk/sunxi-ng/ccu-sun6i-a31.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers') diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-a31.c b/drivers/clk/sunxi-ng/ccu-sun6i-a31.c index 79596463e0d9..4a82a49cff5e 100644 --- a/drivers/clk/sunxi-ng/ccu-sun6i-a31.c +++ b/drivers/clk/sunxi-ng/ccu-sun6i-a31.c @@ -191,6 +191,8 @@ static struct clk_div_table axi_div_table[] = { static SUNXI_CCU_DIV_TABLE(axi_clk, "axi", "cpu", 0x050, 0, 3, axi_div_table, 0); +#define SUN6I_A31_AHB1_REG 0x054 + static const char * const ahb1_parents[] = { "osc32k", "osc24M", "axi", "pll-periph" }; @@ -1230,6 +1232,16 @@ static void __init sun6i_a31_ccu_setup(struct device_node *node) val &= BIT(16); writel(val, reg + SUN6I_A31_PLL_MIPI_REG); + /* Force AHB1 to PLL6 / 3 */ + val = readl(reg + SUN6I_A31_AHB1_REG); + /* set PLL6 pre-div = 3 */ + val &= ~GENMASK(7, 6); + val |= 0x2 << 6; + /* select PLL6 / pre-div */ + val &= ~GENMASK(13, 12); + val |= 0x3 << 12; + writel(val, reg + SUN6I_A31_AHB1_REG); + sunxi_ccu_probe(node, reg, &sun6i_a31_ccu_desc); ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk, -- cgit v1.2.3 From 6a84fb4b4e439a8ef0ce19ec7e7661ad76f655c9 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Fri, 28 Oct 2016 14:34:51 -0700 Subject: device-dax: check devm_nsio_enable() return value If the dax_pmem driver is passed a resource that is already busy the driver probe attempt should fail with a message like the following: dax_pmem dax0.1: could not reserve region [mem 0x100000000-0x11fffffff] However, if we do not catch the error we crash for the obvious reason of accessing memory that is not mapped. BUG: unable to handle kernel paging request at ffffc90020001000 IP: [] __memcpy+0x12/0x20 [..] Call Trace: [] ? nsio_rw_bytes+0x60/0x180 [] nd_pfn_validate+0x75/0x320 [] nvdimm_setup_pfn+0xb9/0x5d0 [] ? devm_nsio_enable+0xff/0x110 [] dax_pmem_probe+0x59/0x260 Cc: Fixes: ab68f2622136 ("/dev/dax, pmem: direct access to persistent memory") Reported-by: Dave Hansen Signed-off-by: Dan Williams --- drivers/dax/pmem.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/dax/pmem.c b/drivers/dax/pmem.c index 4a15fa5df98b..73c6ce93a0d9 100644 --- a/drivers/dax/pmem.c +++ b/drivers/dax/pmem.c @@ -78,7 +78,9 @@ static int dax_pmem_probe(struct device *dev) nsio = to_nd_namespace_io(&ndns->dev); /* parse the 'pfn' info block via ->rw_bytes */ - devm_nsio_enable(dev, nsio); + rc = devm_nsio_enable(dev, nsio); + if (rc) + return rc; altmap = nvdimm_setup_pfn(nd_pfn, &res, &__altmap); if (IS_ERR(altmap)) return PTR_ERR(altmap); -- cgit v1.2.3 From ac95330b96376550ae7a533d1396272d675adfa2 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?St=C3=A9phan=20Rafin?= Date: Fri, 4 Nov 2016 00:53:56 +0100 Subject: clk: sunxi: Fix M factor computation for APB1 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit cfa636886033 ("clk: sunxi: factors: Consolidate get_factors parameters into a struct") introduced a regression for m factor computation in sun4i_get_apb1_factors function. The old code reassigned the "parent_rate" parameter to the targeted divisor value and was buggy for the returned frequency but not for the computed factors. Now, returned frequency is good but m factor is incorrectly computed (its max value 31 is always set resulting in a significantly slower frequency than the requested one...) This patch simply restores the original proper computation for m while keeping the good changes for returned rate. Fixes: cfa636886033 ("clk: sunxi: factors: Consolidate get_factors parameters into a struct") Signed-off-by: Stéphan Rafin Signed-off-by: Maxime Ripard --- drivers/clk/sunxi/clk-sunxi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c index 838b22aa8b67..f2c9274b8bd5 100644 --- a/drivers/clk/sunxi/clk-sunxi.c +++ b/drivers/clk/sunxi/clk-sunxi.c @@ -373,7 +373,7 @@ static void sun4i_get_apb1_factors(struct factors_request *req) else calcp = 3; - calcm = (req->parent_rate >> calcp) - 1; + calcm = (div >> calcp) - 1; req->rate = (req->parent_rate >> calcp) / (calcm + 1); req->m = calcm; -- cgit v1.2.3 From 9bfef729a3d11f04d12788d749a3ce6b47645734 Mon Sep 17 00:00:00 2001 From: Doug Brown Date: Fri, 4 Nov 2016 21:18:20 -0700 Subject: USB: serial: ftdi_sio: add support for TI CC3200 LaunchPad This patch adds support for the TI CC3200 LaunchPad board, which uses a custom USB vendor ID and product ID. Channel A is used for JTAG, and channel B is used for a UART. Signed-off-by: Doug Brown Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/ftdi_sio.c | 2 ++ drivers/usb/serial/ftdi_sio_ids.h | 6 ++++++ 2 files changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 0ff7f38d7800..6e9fc8bcc285 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -1012,6 +1012,8 @@ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(ICPDAS_VID, ICPDAS_I7561U_PID) }, { USB_DEVICE(ICPDAS_VID, ICPDAS_I7563U_PID) }, { USB_DEVICE(WICED_VID, WICED_USB20706V2_PID) }, + { USB_DEVICE(TI_VID, TI_CC3200_LAUNCHPAD_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 21011c0a4c64..48ee04c94a75 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -595,6 +595,12 @@ #define ATMEL_VID 0x03eb /* Vendor ID */ #define STK541_PID 0x2109 /* Zigbee Controller */ +/* + * Texas Instruments + */ +#define TI_VID 0x0451 +#define TI_CC3200_LAUNCHPAD_PID 0xC32A /* SimpleLink Wi-Fi CC3200 LaunchPad */ + /* * Blackfin gnICE JTAG * http://docs.blackfin.uclinux.org/doku.php?id=hw:jtag:gnice -- cgit v1.2.3 From 18f6084a989ba1b38702f9af37a2e4049a924be6 Mon Sep 17 00:00:00 2001 From: Andrey Grodzovsky Date: Thu, 10 Nov 2016 09:35:27 -0500 Subject: scsi: mpt3sas: Fix secure erase premature termination This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming secure erase. Due to the very long time the operation takes, commands issued during the erase will time out and will trigger execution of the abort hook. Even though the abort hook is called for the specific command which timed out, this leads to entire device halt (scsi_state terminated) and premature termination of the secure erase. Set device state to busy while ATA passthrough commands are in progress. [mkp: hand applied to 4.9/scsi-fixes, tweaked patch description] Signed-off-by: Andrey Grodzovsky Acked-by: Sreekanth Reddy Cc: Cc: Sathya Prakash Cc: Chaitra P B Cc: Suganath Prabu Subramani Cc: Sreekanth Reddy Cc: Hannes Reinecke Cc: Signed-off-by: Martin K. Petersen --- drivers/scsi/mpt3sas/mpt3sas_scsih.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c index 8aa769a2d919..91b70bc46e7f 100644 --- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c +++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c @@ -4010,7 +4010,10 @@ _scsih_eedp_error_handling(struct scsi_cmnd *scmd, u16 ioc_status) SAM_STAT_CHECK_CONDITION; } - +static inline bool ata_12_16_cmd(struct scsi_cmnd *scmd) +{ + return (scmd->cmnd[0] == ATA_12 || scmd->cmnd[0] == ATA_16); +} /** * scsih_qcmd - main scsi request entry point @@ -4038,6 +4041,13 @@ scsih_qcmd(struct Scsi_Host *shost, struct scsi_cmnd *scmd) if (ioc->logging_level & MPT_DEBUG_SCSI) scsi_print_command(scmd); + /* + * Lock the device for any subsequent command until command is + * done. + */ + if (ata_12_16_cmd(scmd)) + scsi_internal_device_block(scmd->device); + sas_device_priv_data = scmd->device->hostdata; if (!sas_device_priv_data || !sas_device_priv_data->sas_target) { scmd->result = DID_NO_CONNECT << 16; @@ -4613,6 +4623,9 @@ _scsih_io_done(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 msix_index, u32 reply) if (scmd == NULL) return 1; + if (ata_12_16_cmd(scmd)) + scsi_internal_device_unblock(scmd->device, SDEV_RUNNING); + mpi_request = mpt3sas_base_get_msg_frame(ioc, smid); if (mpi_reply == NULL) { -- cgit v1.2.3 From c733ab3512431436a26e0381829b45794cb13fb0 Mon Sep 17 00:00:00 2001 From: Mauricio Faria de Oliveira Date: Mon, 14 Nov 2016 19:26:22 -0200 Subject: scsi: qla2xxx: do not abort all commands in the adapter during EEH recovery The previous commit 1535aa75a3d8 ("qla2xxx: fix invalid DMA access after command aborts in PCI device remove") introduced a regression during an EEH recovery, since the change to the qla2x00_abort_all_cmds() function calls qla2xxx_eh_abort(), which verifies the EEH recovery condition but handles it heavy-handed. (commit a465537ad1a4 "qla2xxx: Disable the adapter and skip error recovery in case of register disconnect.") This problem warrants a more general/optimistic solution right into qla2xxx_eh_abort() (eg in case a real command abort arrives during EEH recovery, or if it takes long enough to trigger command aborts); but it's still worth to add a check to ensure the code added by the previous commit is correct and contained within its owner function. This commit just adds a 'if (!ha->flags.eeh_busy)' check around it. (ahem; a trivial fix for this -rc series; sorry for this oversight.) With it applied, both PCI device remove and EEH recovery works fine. Fixes: 1535aa75a3d8 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove") Signed-off-by: Mauricio Faria de Oliveira Acked-by: Himanshu Madhani Signed-off-by: Martin K. Petersen --- drivers/scsi/qla2xxx/qla_os.c | 21 +++++++++++++-------- 1 file changed, 13 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index 567fa080e261..56d6142852a5 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -1456,15 +1456,20 @@ qla2x00_abort_all_cmds(scsi_qla_host_t *vha, int res) for (cnt = 1; cnt < req->num_outstanding_cmds; cnt++) { sp = req->outstanding_cmds[cnt]; if (sp) { - /* Get a reference to the sp and drop the lock. - * The reference ensures this sp->done() call - * - and not the call in qla2xxx_eh_abort() - - * ends the SCSI command (with result 'res'). + /* Don't abort commands in adapter during EEH + * recovery as it's not accessible/responding. */ - sp_get(sp); - spin_unlock_irqrestore(&ha->hardware_lock, flags); - qla2xxx_eh_abort(GET_CMD_SP(sp)); - spin_lock_irqsave(&ha->hardware_lock, flags); + if (!ha->flags.eeh_busy) { + /* Get a reference to the sp and drop the lock. + * The reference ensures this sp->done() call + * - and not the call in qla2xxx_eh_abort() - + * ends the SCSI command (with result 'res'). + */ + sp_get(sp); + spin_unlock_irqrestore(&ha->hardware_lock, flags); + qla2xxx_eh_abort(GET_CMD_SP(sp)); + spin_lock_irqsave(&ha->hardware_lock, flags); + } req->outstanding_cmds[cnt] = NULL; sp->done(vha, sp, res); } -- cgit v1.2.3 From 2ce9d2272b98743b911196c49e7af5841381c206 Mon Sep 17 00:00:00 2001 From: Petr Vandrovec Date: Thu, 10 Nov 2016 13:57:14 -0800 Subject: Fix USB CB/CBI storage devices with CONFIG_VMAP_STACK=y Some code (all error handling) submits CDBs that are allocated on the stack. This breaks with CB/CBI code that tries to create URB directly from SCSI command buffer - which happens to be in vmalloced memory with vmalloced kernel stacks. Let's make copy of the command in usb_stor_CB_transport. Signed-off-by: Petr Vandrovec Cc: stable Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/transport.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index ffd086733421..1a59f335b063 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -954,10 +954,15 @@ int usb_stor_CB_transport(struct scsi_cmnd *srb, struct us_data *us) /* COMMAND STAGE */ /* let's send the command via the control pipe */ + /* + * Command is sometime (f.e. after scsi_eh_prep_cmnd) on the stack. + * Stack may be vmallocated. So no DMA for us. Make a copy. + */ + memcpy(us->iobuf, srb->cmnd, srb->cmd_len); result = usb_stor_ctrl_transfer(us, us->send_ctrl_pipe, US_CBI_ADSC, USB_TYPE_CLASS | USB_RECIP_INTERFACE, 0, - us->ifnum, srb->cmnd, srb->cmd_len); + us->ifnum, us->iobuf, srb->cmd_len); /* check the return code for the command */ usb_stor_dbg(us, "Call to usb_stor_ctrl_transfer() returned %d\n", -- cgit v1.2.3 From a5d906bb261cde5f881a949d3b0fbaa285dcc574 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Tue, 15 Nov 2016 18:05:33 +0800 Subject: usb: chipidea: move the lock initialization to core file This can fix below dump when the lock is accessed at host mode due to it is not initialized. [ 46.119638] INFO: trying to register non-static key. [ 46.124643] the code is fine but needs lockdep annotation. [ 46.130144] turning off the locking correctness validator. [ 46.135659] CPU: 0 PID: 690 Comm: cat Not tainted 4.9.0-rc3-00079-g4b75f1d #1210 [ 46.143075] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 46.148923] Backtrace: [ 46.151448] [] (dump_backtrace) from [] (show_stack+0x18/0x1c) [ 46.159038] r7:edf52000 [ 46.161412] r6:60000193 [ 46.163967] r5:00000000 [ 46.165035] r4:c0e25c2c [ 46.169109] [] (show_stack) from [] (dump_stack+0xb4/0xe8) [ 46.176362] [] (dump_stack) from [] (register_lock_class+0x4fc/0x56c) [ 46.184554] r10:c0e25d24 [ 46.187014] r9:edf53e70 [ 46.189569] r8:c1642444 [ 46.190637] r7:ee9da024 [ 46.193191] r6:00000000 [ 46.194258] r5:00000000 [ 46.196812] r4:00000000 [ 46.199185] r3:00000001 [ 46.203259] [] (register_lock_class) from [] (__lock_acquire+0x80/0x10f0) [ 46.211797] r10:c0e25d24 [ 46.214257] r9:edf53e70 [ 46.216813] r8:ee9da024 [ 46.217880] r7:c1642444 [ 46.220435] r6:edcd1800 [ 46.221502] r5:60000193 [ 46.224057] r4:00000000 [ 46.227953] [] (__lock_acquire) from [] (lock_acquire+0x74/0x94) [ 46.235710] r10:00000001 [ 46.238169] r9:edf53e70 [ 46.240723] r8:edf53f80 [ 46.241790] r7:00000001 [ 46.244344] r6:00000001 [ 46.245412] r5:60000193 [ 46.247966] r4:00000000 [ 46.251866] [] (lock_acquire) from [] (_raw_spin_lock_irqsave+0x40/0x54) [ 46.260319] r7:ee1c6a00 [ 46.262691] r6:c062a570 [ 46.265247] r5:20000113 [ 46.266314] r4:ee9da014 [ 46.270393] [] (_raw_spin_lock_irqsave) from [] (ci_port_test_show+0x2c/0x70) [ 46.279280] r6:eebd2000 [ 46.281652] r5:ee9da010 [ 46.284207] r4:ee9da014 [ 46.286810] [] (ci_port_test_show) from [] (seq_read+0x1ac/0x4f8) [ 46.294655] r9:edf53e70 [ 46.297028] r8:edf53f80 [ 46.299583] r7:ee1c6a00 [ 46.300650] r6:00000001 [ 46.303205] r5:00000000 [ 46.304273] r4:eebd2000 [ 46.306850] [] (seq_read) from [] (full_proxy_read+0x54/0x6c) [ 46.314348] r10:00000000 [ 46.316808] r9:c0a6ad30 [ 46.319363] r8:edf53f80 [ 46.320430] r7:00020000 [ 46.322986] r6:b6de3000 [ 46.324053] r5:ee1c6a00 [ 46.326607] r4:c0248b58 [ 46.330505] [] (full_proxy_read) from [] (__vfs_read+0x34/0x118) [ 46.338262] r9:edf52000 [ 46.340635] r8:c0107fc4 [ 46.343190] r7:00020000 [ 46.344257] r6:edf53f80 [ 46.346812] r5:c039e810 [ 46.347879] r4:ee1c6a00 [ 46.350447] [] (__vfs_read) from [] (vfs_read+0x8c/0x11c) [ 46.357597] r9:edf52000 [ 46.359969] r8:c0107fc4 [ 46.362524] r7:edf53f80 [ 46.363592] r6:b6de3000 [ 46.366147] r5:ee1c6a00 [ 46.367214] r4:00020000 [ 46.369782] [] (vfs_read) from [] (SyS_read+0x4c/0xa8) [ 46.376672] r8:c0107fc4 [ 46.379045] r7:00020000 [ 46.381600] r6:b6de3000 [ 46.382667] r5:ee1c6a00 [ 46.385222] r4:ee1c6a00 [ 46.387817] [] (SyS_read) from [] (ret_fast_syscall+0x0/0x1c) [ 46.395314] r7:00000003 [ 46.397687] r6:b6de3000 [ 46.400243] r5:00020000 [ 46.401310] r4:00020000 Cc: Fixes: 26c696c678c4 ("USB: Chipidea: rename struct ci13xxx variables from udc to ci") Signed-off-by: Peter Chen Signed-off-by: Greg Kroah-Hartman --- drivers/usb/chipidea/core.c | 1 + drivers/usb/chipidea/udc.c | 2 -- 2 files changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index 69426e644d17..3dbb4a21ab44 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -914,6 +914,7 @@ static int ci_hdrc_probe(struct platform_device *pdev) if (!ci) return -ENOMEM; + spin_lock_init(&ci->lock); ci->dev = dev; ci->platdata = dev_get_platdata(dev); ci->imx28_write_fix = !!(ci->platdata->flags & diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c index 661f43fe0f9e..c9e80ad48fdc 100644 --- a/drivers/usb/chipidea/udc.c +++ b/drivers/usb/chipidea/udc.c @@ -1889,8 +1889,6 @@ static int udc_start(struct ci_hdrc *ci) struct usb_otg_caps *otg_caps = &ci->platdata->ci_otg_caps; int retval = 0; - spin_lock_init(&ci->lock); - ci->gadget.ops = &usb_gadget_ops; ci->gadget.speed = USB_SPEED_UNKNOWN; ci->gadget.max_speed = USB_SPEED_HIGH; -- cgit v1.2.3 From 2ab13292d7a314fa45de0acc808e41aaad31989c Mon Sep 17 00:00:00 2001 From: Paul Jakma Date: Wed, 16 Nov 2016 10:13:49 +0000 Subject: USB: serial: cp210x: add ID for the Zone DPMX The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB serial interface in its charging dock for the control pods, via which some settings for the pods can be modified. Signed-off-by: Paul Jakma Cc: Barry Redmond Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/cp210x.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index f61477bed3a8..243ac5ebe46a 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -131,6 +131,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */ { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */ { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */ + { USB_DEVICE(0x10C4, 0x8962) }, /* Brim Brothers charging dock */ { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */ { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */ { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */ -- cgit v1.2.3 From 4cb19355ea19995941ccaad115dbfac6b75215ca Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 16 Nov 2016 09:00:38 -0800 Subject: device-dax: fail all private mapping attempts The device-dax implementation originally tried to be tricky and allow private read-only mappings, but in the process allowed writable MAP_PRIVATE + MAP_NORESERVE mappings. For simplicity and predictability just fail all private mapping attempts since device-dax memory is statically allocated and will never support overcommit. Cc: Cc: Dave Hansen Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap") Reported-by: Pawel Lebioda Signed-off-by: Dan Williams --- drivers/dax/dax.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/dax/dax.c b/drivers/dax/dax.c index 0e499bfca41c..3d94ff20fdca 100644 --- a/drivers/dax/dax.c +++ b/drivers/dax/dax.c @@ -270,8 +270,8 @@ static int check_vma(struct dax_dev *dax_dev, struct vm_area_struct *vma, if (!dax_dev->alive) return -ENXIO; - /* prevent private / writable mappings from being established */ - if ((vma->vm_flags & (VM_NORESERVE|VM_SHARED|VM_WRITE)) == VM_WRITE) { + /* prevent private mappings from being established */ + if ((vma->vm_flags & VM_SHARED) != VM_SHARED) { dev_info(dev, "%s: %s: fail, attempted private mapping\n", current->comm, func); return -EINVAL; -- cgit v1.2.3 From 3ca0b51decf780ce6277b088a9f28cd6fb71e372 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Wed, 16 Nov 2016 11:02:00 -0800 Subject: clk: berlin: Pass correct type to hw provider registration Dan Carpenter reports that we're passing a pointer to a pointer here when we should just be passing a pointer. Pass the right pointer so that the of_clk_hw_onecell_get() sees the appropriate data pointer on its end. Reported-by: Dan Carpenter Cc: Jisheng Zhang Cc: Alexandre Belloni Cc: Sebastian Hesselbarth Cc: Stephen Boyd Fixes: f6475e298297 ("clk: berlin: Migrate to clk_hw based registration and OF APIs") Signed-off-by: Stephen Boyd --- drivers/clk/berlin/bg2.c | 2 +- drivers/clk/berlin/bg2q.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/clk/berlin/bg2.c b/drivers/clk/berlin/bg2.c index edf3b96b3b73..1d99292e2039 100644 --- a/drivers/clk/berlin/bg2.c +++ b/drivers/clk/berlin/bg2.c @@ -685,7 +685,7 @@ static void __init berlin2_clock_setup(struct device_node *np) } /* register clk-provider */ - of_clk_add_hw_provider(np, of_clk_hw_onecell_get, &clk_data); + of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data); return; diff --git a/drivers/clk/berlin/bg2q.c b/drivers/clk/berlin/bg2q.c index 0718e831475f..3b784b593afd 100644 --- a/drivers/clk/berlin/bg2q.c +++ b/drivers/clk/berlin/bg2q.c @@ -382,7 +382,7 @@ static void __init berlin2q_clock_setup(struct device_node *np) } /* register clk-provider */ - of_clk_add_hw_provider(np, of_clk_hw_onecell_get, &clk_data); + of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data); return; -- cgit v1.2.3 From bdfdabfedc30c9574dde6198a1739d2be03bf934 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Wed, 16 Nov 2016 11:02:00 -0800 Subject: clk: efm32gg: Pass correct type to hw provider registration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Dan Carpenter reports that we're passing a pointer to a pointer here when we should just be passing a pointer. Pass the right pointer so that the of_clk_hw_onecell_get() sees the appropriate data pointer on its end. Reported-by: Dan Carpenter Cc: Stephen Boyd Cc: Uwe Kleine-König Fixes: 9337631f52a8 ("clk: efm32gg: Migrate to clk_hw based OF and registration APIs") Signed-off-by: Stephen Boyd --- drivers/clk/clk-efm32gg.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/clk/clk-efm32gg.c b/drivers/clk/clk-efm32gg.c index 8802a2dd56ac..f674778fb3ac 100644 --- a/drivers/clk/clk-efm32gg.c +++ b/drivers/clk/clk-efm32gg.c @@ -82,6 +82,6 @@ static void __init efm32gg_cmu_init(struct device_node *np) hws[clk_HFPERCLKDAC0] = clk_hw_register_gate(NULL, "HFPERCLK.DAC0", "HFXO", 0, base + CMU_HFPERCLKEN0, 17, 0, NULL); - of_clk_add_hw_provider(np, of_clk_hw_onecell_get, &clk_data); + of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data); } CLK_OF_DECLARE(efm32ggcmu, "efm32gg,cmu", efm32gg_cmu_init); -- cgit v1.2.3 From da7800a88c5a3b798f763d6f9f343e9a49860c4f Mon Sep 17 00:00:00 2001 From: Rex Zhu Date: Mon, 14 Nov 2016 16:36:08 +0800 Subject: drm/amd/powerplay: avoid out of bounds access on array ps. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit check array index first and then visit the array. Signed-off-by: Rex Zhu Reviewed-by: Christian König Reviewed-by: Alex Deucher Signed-off-by: Alex Deucher --- drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c index 13f2b705ea49..08cd0bd3ebe5 100644 --- a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +++ b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c @@ -2984,19 +2984,19 @@ static int smu7_get_pp_table_entry_callback_func_v0(struct pp_hwmgr *hwmgr, if (!(data->mc_micro_code_feature & DISABLE_MC_LOADMICROCODE) && memory_clock > data->highest_mclk) data->highest_mclk = memory_clock; - performance_level = &(ps->performance_levels - [ps->performance_level_count++]); - PP_ASSERT_WITH_CODE( (ps->performance_level_count < smum_get_mac_definition(hwmgr->smumgr, SMU_MAX_LEVELS_GRAPHICS)), "Performance levels exceeds SMC limit!", return -EINVAL); PP_ASSERT_WITH_CODE( - (ps->performance_level_count <= + (ps->performance_level_count < hwmgr->platform_descriptor.hardwareActivityPerformanceLevels), - "Performance levels exceeds Driver limit!", - return -EINVAL); + "Performance levels exceeds Driver limit, Skip!", + return 0); + + performance_level = &(ps->performance_levels + [ps->performance_level_count++]); /* Performance levels are arranged from low to high. */ performance_level->memory_clock = memory_clock; -- cgit v1.2.3 From c723bd6ec2b50e7c8b3424d9cb8febd8ffa3da1f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:22 -0600 Subject: usb: musb: Fix broken use of static variable for multiple instances We can't use static variable first for checking when musb is initialized when we have multiple musb instances like on am335x. Tested-by: Ladislav Michl Reviewed-by: Johan Hovold Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 9 +++++---- drivers/usb/musb/musb_core.h | 2 ++ 2 files changed, 7 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index e01116e4c067..f1ea4494dcb2 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -2291,6 +2291,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) if (status) goto fail5; + musb->is_initialized = 1; pm_runtime_mark_last_busy(musb->controller); pm_runtime_put_autosuspend(musb->controller); @@ -2629,7 +2630,6 @@ static int musb_runtime_suspend(struct device *dev) static int musb_runtime_resume(struct device *dev) { struct musb *musb = dev_to_musb(dev); - static int first = 1; /* * When pm_runtime_get_sync called for the first time in driver @@ -2640,9 +2640,10 @@ static int musb_runtime_resume(struct device *dev) * Also context restore without save does not make * any sense */ - if (!first) - musb_restore_context(musb); - first = 0; + if (!musb->is_initialized) + return 0; + + musb_restore_context(musb); if (musb->need_finish_resume) { musb->need_finish_resume = 0; diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 2cb88a498f8a..c04abf424c5c 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -385,6 +385,8 @@ struct musb { int a_wait_bcon; /* VBUS timeout in msecs */ unsigned long idle_timeout; /* Next timeout in jiffies */ + unsigned is_initialized:1; + /* active means connected and not suspended */ unsigned is_active:1; -- cgit v1.2.3 From ea2f35c01d5ea72b43b9b4fb4c5b9417a9eb2fb8 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:23 -0600 Subject: usb: musb: Fix sleeping function called from invalid context for hdrc glue Commit 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer that runs in softirq context. That causes a "BUG: sleeping function called from invalid context" every time when polling the cable status: [] (__might_sleep) from [] (__pm_runtime_resume+0x9c/0xa0) [] (__pm_runtime_resume) from [] (otg_timer+0x3c/0x254) [] (otg_timer) from [] (call_timer_fn+0xfc/0x41c) [] (call_timer_fn) from [] (expire_timers+0x120/0x210) [] (expire_timers) from [] (run_timer_softirq+0xa4/0xdc) [] (run_timer_softirq) from [] (__do_softirq+0x12c/0x594) I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled. And looks like also musb_gadget_queue() suffers from the same problem. Let's fix the issue by using a list of delayed work then call it on resume. Note that we want to do this only when musb core and it's parent devices are awake, and we need to make sure the DSPS glue timer is stopped as noted by Johan Hovold . Note that we already are re-enabling the timer with mod_timer() in dsps_musb_enable(). Later on we may be able to remove other delayed work in the musb driver and just do it from pending_resume_work. But this should be done only for delayed work that does not have other timing requirements beyond just being run on resume. Fixes: 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS glue layer") Reported-by: Johan Hovold Reviewed-by: Johan Hovold Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 109 +++++++++++++++++++++++++++++++++++++++-- drivers/usb/musb/musb_core.h | 7 +++ drivers/usb/musb/musb_dsps.c | 36 ++++++++++---- drivers/usb/musb/musb_gadget.c | 33 +++++++++++-- 4 files changed, 167 insertions(+), 18 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index f1ea4494dcb2..384de6cd26f5 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1969,6 +1969,7 @@ static struct musb *allocate_instance(struct device *dev, INIT_LIST_HEAD(&musb->control); INIT_LIST_HEAD(&musb->in_bulk); INIT_LIST_HEAD(&musb->out_bulk); + INIT_LIST_HEAD(&musb->pending_list); musb->vbuserr_retry = VBUSERR_RETRY_COUNT; musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON; @@ -2018,6 +2019,84 @@ static void musb_free(struct musb *musb) musb_host_free(musb); } +struct musb_pending_work { + int (*callback)(struct musb *musb, void *data); + void *data; + struct list_head node; +}; + +/* + * Called from musb_runtime_resume(), musb_resume(), and + * musb_queue_resume_work(). Callers must take musb->lock. + */ +static int musb_run_resume_work(struct musb *musb) +{ + struct musb_pending_work *w, *_w; + unsigned long flags; + int error = 0; + + spin_lock_irqsave(&musb->list_lock, flags); + list_for_each_entry_safe(w, _w, &musb->pending_list, node) { + if (w->callback) { + error = w->callback(musb, w->data); + if (error < 0) { + dev_err(musb->controller, + "resume callback %p failed: %i\n", + w->callback, error); + } + } + list_del(&w->node); + devm_kfree(musb->controller, w); + } + spin_unlock_irqrestore(&musb->list_lock, flags); + + return error; +} + +/* + * Called to run work if device is active or else queue the work to happen + * on resume. Caller must take musb->lock and must hold an RPM reference. + * + * Note that we cowardly refuse queuing work after musb PM runtime + * resume is done calling musb_run_resume_work() and return -EINPROGRESS + * instead. + */ +int musb_queue_resume_work(struct musb *musb, + int (*callback)(struct musb *musb, void *data), + void *data) +{ + struct musb_pending_work *w; + unsigned long flags; + int error; + + if (WARN_ON(!callback)) + return -EINVAL; + + if (pm_runtime_active(musb->controller)) + return callback(musb, data); + + w = devm_kzalloc(musb->controller, sizeof(*w), GFP_ATOMIC); + if (!w) + return -ENOMEM; + + w->callback = callback; + w->data = data; + spin_lock_irqsave(&musb->list_lock, flags); + if (musb->is_runtime_suspended) { + list_add_tail(&w->node, &musb->pending_list); + error = 0; + } else { + dev_err(musb->controller, "could not add resume work %p\n", + callback); + devm_kfree(musb->controller, w); + error = -EINPROGRESS; + } + spin_unlock_irqrestore(&musb->list_lock, flags); + + return error; +} +EXPORT_SYMBOL_GPL(musb_queue_resume_work); + static void musb_deassert_reset(struct work_struct *work) { struct musb *musb; @@ -2065,6 +2144,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) } spin_lock_init(&musb->lock); + spin_lock_init(&musb->list_lock); musb->board_set_power = plat->set_power; musb->min_power = plat->min_power; musb->ops = plat->platform_ops; @@ -2558,6 +2638,7 @@ static int musb_suspend(struct device *dev) musb_platform_disable(musb); musb_generic_disable(musb); + WARN_ON(!list_empty(&musb->pending_list)); spin_lock_irqsave(&musb->lock, flags); @@ -2579,9 +2660,11 @@ static int musb_suspend(struct device *dev) static int musb_resume(struct device *dev) { - struct musb *musb = dev_to_musb(dev); - u8 devctl; - u8 mask; + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + int error; + u8 devctl; + u8 mask; /* * For static cmos like DaVinci, register values were preserved @@ -2615,6 +2698,13 @@ static int musb_resume(struct device *dev) musb_start(musb); + spin_lock_irqsave(&musb->lock, flags); + error = musb_run_resume_work(musb); + if (error) + dev_err(musb->controller, "resume work failed with %i\n", + error); + spin_unlock_irqrestore(&musb->lock, flags); + return 0; } @@ -2623,13 +2713,16 @@ static int musb_runtime_suspend(struct device *dev) struct musb *musb = dev_to_musb(dev); musb_save_context(musb); + musb->is_runtime_suspended = 1; return 0; } static int musb_runtime_resume(struct device *dev) { - struct musb *musb = dev_to_musb(dev); + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + int error; /* * When pm_runtime_get_sync called for the first time in driver @@ -2651,6 +2744,14 @@ static int musb_runtime_resume(struct device *dev) msecs_to_jiffies(USB_RESUME_TIMEOUT)); } + spin_lock_irqsave(&musb->lock, flags); + error = musb_run_resume_work(musb); + if (error) + dev_err(musb->controller, "resume work failed with %i\n", + error); + musb->is_runtime_suspended = 0; + spin_unlock_irqrestore(&musb->lock, flags); + return 0; } diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index c04abf424c5c..15b1f93c7037 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -303,6 +303,7 @@ struct musb_context_registers { struct musb { /* device lock */ spinlock_t lock; + spinlock_t list_lock; /* resume work list lock */ struct musb_io io; const struct musb_platform_ops *ops; @@ -337,6 +338,7 @@ struct musb { struct list_head control; /* of musb_qh */ struct list_head in_bulk; /* of musb_qh */ struct list_head out_bulk; /* of musb_qh */ + struct list_head pending_list; /* pending work list */ struct timer_list otg_timer; struct notifier_block nb; @@ -386,6 +388,7 @@ struct musb { unsigned long idle_timeout; /* Next timeout in jiffies */ unsigned is_initialized:1; + unsigned is_runtime_suspended:1; /* active means connected and not suspended */ unsigned is_active:1; @@ -542,6 +545,10 @@ extern irqreturn_t musb_interrupt(struct musb *); extern void musb_hnp_stop(struct musb *musb); +int musb_queue_resume_work(struct musb *musb, + int (*callback)(struct musb *musb, void *data), + void *data); + static inline void musb_platform_set_vbus(struct musb *musb, int is_on) { if (musb->ops->set_vbus) diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 0f17d2140db6..6096c84ab67a 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -185,24 +185,19 @@ static void dsps_musb_disable(struct musb *musb) musb_writel(reg_base, wrp->coreintr_clear, wrp->usb_bitmap); musb_writel(reg_base, wrp->epintr_clear, wrp->txep_bitmap | wrp->rxep_bitmap); + del_timer_sync(&glue->timer); musb_writeb(musb->mregs, MUSB_DEVCTL, 0); } -static void otg_timer(unsigned long _musb) +/* Caller must take musb->lock */ +static int dsps_check_status(struct musb *musb, void *unused) { - struct musb *musb = (void *)_musb; void __iomem *mregs = musb->mregs; struct device *dev = musb->controller; struct dsps_glue *glue = dev_get_drvdata(dev->parent); const struct dsps_musb_wrapper *wrp = glue->wrp; u8 devctl; - unsigned long flags; int skip_session = 0; - int err; - - err = pm_runtime_get_sync(dev); - if (err < 0) - dev_err(dev, "Poll could not pm_runtime_get: %i\n", err); /* * We poll because DSPS IP's won't expose several OTG-critical @@ -212,7 +207,6 @@ static void otg_timer(unsigned long _musb) dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl, usb_otg_state_string(musb->xceiv->otg->state)); - spin_lock_irqsave(&musb->lock, flags); switch (musb->xceiv->otg->state) { case OTG_STATE_A_WAIT_VRISE: mod_timer(&glue->timer, jiffies + @@ -245,8 +239,30 @@ static void otg_timer(unsigned long _musb) default: break; } - spin_unlock_irqrestore(&musb->lock, flags); + return 0; +} + +static void otg_timer(unsigned long _musb) +{ + struct musb *musb = (void *)_musb; + struct device *dev = musb->controller; + unsigned long flags; + int err; + + err = pm_runtime_get(dev); + if ((err != -EINPROGRESS) && err < 0) { + dev_err(dev, "Poll could not pm_runtime_get: %i\n", err); + pm_runtime_put_noidle(dev); + + return; + } + + spin_lock_irqsave(&musb->lock, flags); + err = musb_queue_resume_work(musb, dsps_check_status, NULL); + if (err < 0) + dev_err(dev, "%s resume work: %i\n", __func__, err); + spin_unlock_irqrestore(&musb->lock, flags); pm_runtime_mark_last_busy(dev); pm_runtime_put_autosuspend(dev); } diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 4042ea017985..910f50967627 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1222,13 +1222,22 @@ void musb_ep_restart(struct musb *musb, struct musb_request *req) rxstate(musb, req); } +static int musb_ep_restart_resume_work(struct musb *musb, void *data) +{ + struct musb_request *req = data; + + musb_ep_restart(musb, req); + + return 0; +} + static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, gfp_t gfp_flags) { struct musb_ep *musb_ep; struct musb_request *request; struct musb *musb; - int status = 0; + int status; unsigned long lockflags; if (!ep || !req) @@ -1245,6 +1254,17 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, if (request->ep != musb_ep) return -EINVAL; + status = pm_runtime_get(musb->controller); + if ((status != -EINPROGRESS) && status < 0) { + dev_err(musb->controller, + "pm runtime get failed in %s\n", + __func__); + pm_runtime_put_noidle(musb->controller); + + return status; + } + status = 0; + trace_musb_req_enq(request); /* request is mine now... */ @@ -1255,7 +1275,6 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, map_dma_buffer(request, musb, musb_ep); - pm_runtime_get_sync(musb->controller); spin_lock_irqsave(&musb->lock, lockflags); /* don't queue if the ep is down */ @@ -1271,8 +1290,14 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, list_add_tail(&request->list, &musb_ep->req_list); /* it this is the head of the queue, start i/o ... */ - if (!musb_ep->busy && &request->list == musb_ep->req_list.next) - musb_ep_restart(musb, request); + if (!musb_ep->busy && &request->list == musb_ep->req_list.next) { + status = musb_queue_resume_work(musb, + musb_ep_restart_resume_work, + request); + if (status < 0) + dev_err(musb->controller, "%s resume work: %i\n", + __func__, status); + } unlock: spin_unlock_irqrestore(&musb->lock, lockflags); -- cgit v1.2.3 From 2bff3916fda9145587c0312b6f5c43d82504980c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:24 -0600 Subject: usb: musb: Fix PM for hub disconnect With a USB hub disconnected, devctl can be 0x19 for about a second on am335x and will stay forever on at least omap3. And we get no further interrupts when devctl session bit clears. This keeps PM runtime active. Let's fix the issue by polling devctl until the session bit clears or times out. We can do this by making musb->irq_work into delayed_work. And with the polling implemented, we can now also have the quirk for invalid VBUS it to avoid disconnecting too early while VBUS is ramping up. Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") Fixes: 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS Tested-by: Ladislav Michl Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 29 +++++++++++++++++++---------- drivers/usb/musb/musb_core.h | 4 ++-- drivers/usb/musb/musb_gadget.c | 6 +++--- drivers/usb/musb/tusb6010.c | 6 +++--- 4 files changed, 27 insertions(+), 18 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 384de6cd26f5..c3e172e15ec3 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -986,7 +986,7 @@ b_host: } #endif - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); return handled; } @@ -1855,14 +1855,23 @@ static void musb_pm_runtime_check_session(struct musb *musb) MUSB_DEVCTL_HR; switch (devctl & ~s) { case MUSB_QUIRK_B_INVALID_VBUS_91: - if (!musb->session && !musb->quirk_invalid_vbus) { - musb->quirk_invalid_vbus = true; + if (musb->quirk_retries--) { musb_dbg(musb, - "First invalid vbus, assume no session"); + "Poll devctl on invalid vbus, assume no session"); + schedule_delayed_work(&musb->irq_work, + msecs_to_jiffies(1000)); + return; } - break; case MUSB_QUIRK_A_DISCONNECT_19: + if (musb->quirk_retries--) { + musb_dbg(musb, + "Poll devctl on possible host mode disconnect"); + schedule_delayed_work(&musb->irq_work, + msecs_to_jiffies(1000)); + + return; + } if (!musb->session) break; musb_dbg(musb, "Allow PM on possible host mode disconnect"); @@ -1886,9 +1895,9 @@ static void musb_pm_runtime_check_session(struct musb *musb) if (error < 0) dev_err(musb->controller, "Could not enable: %i\n", error); + musb->quirk_retries = 3; } else { musb_dbg(musb, "Allow PM with no session: %02x", devctl); - musb->quirk_invalid_vbus = false; pm_runtime_mark_last_busy(musb->controller); pm_runtime_put_autosuspend(musb->controller); } @@ -1899,7 +1908,7 @@ static void musb_pm_runtime_check_session(struct musb *musb) /* Only used to provide driver mode change events */ static void musb_irq_work(struct work_struct *data) { - struct musb *musb = container_of(data, struct musb, irq_work); + struct musb *musb = container_of(data, struct musb, irq_work.work); musb_pm_runtime_check_session(musb); @@ -2288,7 +2297,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) musb_generic_disable(musb); /* Init IRQ workqueue before request_irq */ - INIT_WORK(&musb->irq_work, musb_irq_work); + INIT_DELAYED_WORK(&musb->irq_work, musb_irq_work); INIT_DELAYED_WORK(&musb->deassert_reset_work, musb_deassert_reset); INIT_DELAYED_WORK(&musb->finish_resume_work, musb_host_finish_resume); @@ -2385,7 +2394,7 @@ fail4: musb_host_cleanup(musb); fail3: - cancel_work_sync(&musb->irq_work); + cancel_delayed_work_sync(&musb->irq_work); cancel_delayed_work_sync(&musb->finish_resume_work); cancel_delayed_work_sync(&musb->deassert_reset_work); if (musb->dma_controller) @@ -2452,7 +2461,7 @@ static int musb_remove(struct platform_device *pdev) */ musb_exit_debugfs(musb); - cancel_work_sync(&musb->irq_work); + cancel_delayed_work_sync(&musb->irq_work); cancel_delayed_work_sync(&musb->finish_resume_work); cancel_delayed_work_sync(&musb->deassert_reset_work); pm_runtime_get_sync(musb->controller); diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 15b1f93c7037..91817d77d59c 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -310,7 +310,7 @@ struct musb { struct musb_context_registers context; irqreturn_t (*isr)(int, void *); - struct work_struct irq_work; + struct delayed_work irq_work; struct delayed_work deassert_reset_work; struct delayed_work finish_resume_work; struct delayed_work gadget_work; @@ -381,7 +381,7 @@ struct musb { int port_mode; /* MUSB_PORT_MODE_* */ bool session; - bool quirk_invalid_vbus; + unsigned long quirk_retries; bool is_host; int a_wait_bcon; /* VBUS timeout in msecs */ diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 910f50967627..a55173c9e564 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1114,7 +1114,7 @@ static int musb_gadget_enable(struct usb_ep *ep, musb_ep->dma ? "dma, " : "", musb_ep->packet_sz); - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); fail: spin_unlock_irqrestore(&musb->lock, flags); @@ -1158,7 +1158,7 @@ static int musb_gadget_disable(struct usb_ep *ep) musb_ep->desc = NULL; musb_ep->end_point.desc = NULL; - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); spin_unlock_irqrestore(&(musb->lock), flags); @@ -1994,7 +1994,7 @@ static int musb_gadget_stop(struct usb_gadget *g) */ /* Force check of devctl register for PM runtime */ - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); pm_runtime_mark_last_busy(musb->controller); pm_runtime_put_autosuspend(musb->controller); diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index df7c9f46be54..e85cc8e4e7a9 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -724,7 +724,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) dev_dbg(musb->controller, "vbus change, %s, otg %03x\n", usb_otg_state_string(musb->xceiv->otg->state), otg_stat); idle_timeout = jiffies + (1 * HZ); - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); } else /* A-dev state machine */ { dev_dbg(musb->controller, "vbus change, %s, otg %03x\n", @@ -814,7 +814,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) break; } } - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); return idle_timeout; } @@ -864,7 +864,7 @@ static irqreturn_t tusb_musb_interrupt(int irq, void *__hci) musb_writel(tbase, TUSB_PRCM_WAKEUP_CLEAR, reg); if (reg & ~TUSB_PRCM_WNORCS) { musb->is_active = 1; - schedule_work(&musb->irq_work); + schedule_delayed_work(&musb->irq_work, 0); } dev_dbg(musb->controller, "wake %sactive %02x\n", musb->is_active ? "" : "in", reg); -- cgit v1.2.3 From 536d599d4a5104a8f1f771d3a8db97138b0c9ebb Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:25 -0600 Subject: usb: musb: Add missing pm_runtime_disable and drop 2430 PM timeout We are missing pm_runtime_disable() in 2430 glue layer. Further, we only need to enable PM runtime and disable it on exit. With musb_core.c doing PM, the glue layer as a parent will always be active when musb_core.c is active. This fixes host enumeration issues with some devices as reported by Ladislav Michl . And holding an RPM reference while deregistering the child would lead to a crash in omap2430_runtime_suspend() which dereferences the now freed child's driver data on put as pointed out by Johan Hovold : Unable to handle kernel paging request at virtual address 6b6b6f17 ... [] (omap2430_runtime_suspend) from [] (pm_generic_runtime_suspend+0x3c/0x48) [] (pm_generic_runtime_suspend) from [] (_od_runtime_suspend+0x1c/0x30) [] (_od_runtime_suspend) from [] (__rpm_callback+0x3c/0x70) [] (__rpm_callback) from [] (rpm_callback+0x30/0x90) [] (rpm_callback) from [] (rpm_suspend+0x118/0x6b4) [] (rpm_suspend) from [] (rpm_idle+0x104/0x440) [] (rpm_idle) from [] (__pm_runtime_idle+0x7c/0xb0) [] (__pm_runtime_idle) from [] (omap2430_remove+0x38/0x58) [] (omap2430_remove) from [] (platform_drv_remove+0x34/0x4c) Note that if changes are needed to the autosuspend timeout, it should be done in musb_core.c. Reported-by: Ladislav Michl Fixes: 87326e858448 ("usb: musb: Remove extra PM runtime calls from 2430 glue layer") Tested-by: Ladislav Michl Reviewed-by: Johan Hovold Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/omap2430.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index cc1225485509..e8be8e39ab8f 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -513,17 +513,18 @@ static int omap2430_probe(struct platform_device *pdev) } pm_runtime_enable(glue->dev); - pm_runtime_use_autosuspend(glue->dev); - pm_runtime_set_autosuspend_delay(glue->dev, 100); ret = platform_device_add(musb); if (ret) { dev_err(&pdev->dev, "failed to register musb device\n"); - goto err2; + goto err3; } return 0; +err3: + pm_runtime_disable(glue->dev); + err2: platform_device_put(musb); @@ -535,10 +536,7 @@ static int omap2430_remove(struct platform_device *pdev) { struct omap2430_glue *glue = platform_get_drvdata(pdev); - pm_runtime_get_sync(glue->dev); platform_device_unregister(glue->musb); - pm_runtime_put_sync(glue->dev); - pm_runtime_dont_use_autosuspend(glue->dev); pm_runtime_disable(glue->dev); return 0; -- cgit v1.2.3 From 247529170d72ee16bbdfc94c3a696c79ea645c3a Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:26 -0600 Subject: usb: musb: Drop pointless PM runtime code for dsps glue This already gets done automatically by PM runtime and we have a separate autosuspend timeout in musb_core.c. Reviewed-by: Johan Hovold Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_dsps.c | 22 ++-------------------- 1 file changed, 2 insertions(+), 20 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 6096c84ab67a..feae1561b9ab 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -783,28 +783,13 @@ static int dsps_probe(struct platform_device *pdev) platform_set_drvdata(pdev, glue); pm_runtime_enable(&pdev->dev); - pm_runtime_use_autosuspend(&pdev->dev); - pm_runtime_set_autosuspend_delay(&pdev->dev, 200); - - ret = pm_runtime_get_sync(&pdev->dev); - if (ret < 0) { - dev_err(&pdev->dev, "pm_runtime_get_sync FAILED"); - goto err2; - } - ret = dsps_create_musb_pdev(glue, pdev); if (ret) - goto err3; - - pm_runtime_mark_last_busy(&pdev->dev); - pm_runtime_put_autosuspend(&pdev->dev); + goto err; return 0; -err3: - pm_runtime_put_sync(&pdev->dev); -err2: - pm_runtime_dont_use_autosuspend(&pdev->dev); +err: pm_runtime_disable(&pdev->dev); return ret; } @@ -815,9 +800,6 @@ static int dsps_remove(struct platform_device *pdev) platform_device_unregister(glue->musb); - /* disable usbss clocks */ - pm_runtime_dont_use_autosuspend(&pdev->dev); - pm_runtime_put_sync(&pdev->dev); pm_runtime_disable(&pdev->dev); return 0; -- cgit v1.2.3 From f7c4a46352b58c04e4d2111df7fe0358ce84546d Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 16 Nov 2016 13:21:27 -0600 Subject: phy: twl4030-usb: Fix for musb session bit based PM Now with musb driver implementing generic session bit based PM, we need to have the USB PHYs behaving in a sane way for platforms implementing PM. Currently twl4030-usb enables PM in twl4030_phy_power_on() and then disables it in twl4030_phy_power_off(). This will block PM runtime for the SoC when no cable is connected. Fix the issue by moving PM runtime autosuspend call to happen where it gets called in twl4030_phy_power_on(). Note that this patch should not be backported to anything before commit 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") as before that all the glue layers implemented their own PM. Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") Tested-by: Ladislav Michl Tested-by: Laurent Pinchart Signed-off-by: Tony Lindgren Acked-by: Kishon Vijay Abraham I Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman --- drivers/phy/phy-twl4030-usb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/phy/phy-twl4030-usb.c b/drivers/phy/phy-twl4030-usb.c index 87e6334eab93..547ca7b3f098 100644 --- a/drivers/phy/phy-twl4030-usb.c +++ b/drivers/phy/phy-twl4030-usb.c @@ -459,8 +459,6 @@ static int twl4030_phy_power_off(struct phy *phy) struct twl4030_usb *twl = phy_get_drvdata(phy); dev_dbg(twl->dev, "%s\n", __func__); - pm_runtime_mark_last_busy(twl->dev); - pm_runtime_put_autosuspend(twl->dev); return 0; } @@ -472,6 +470,8 @@ static int twl4030_phy_power_on(struct phy *phy) dev_dbg(twl->dev, "%s\n", __func__); pm_runtime_get_sync(twl->dev); schedule_delayed_work(&twl->id_workaround_work, HZ); + pm_runtime_mark_last_busy(twl->dev); + pm_runtime_put_autosuspend(twl->dev); return 0; } -- cgit v1.2.3 From 05e78c6933d613a7da0d0473f4c19c865af04c2c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Felix=20H=C3=A4dicke?= Date: Fri, 4 Nov 2016 00:23:26 +0100 Subject: usb: gadget: f_fs: fix wrong parenthesis in ffs_func_req_match() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Properly check the return code of ffs_func_revmap_intf() and ffs_func_revmap_ep() for a non-negative value. Instead of checking the return code, the comparison was performed for the last parameter of the function calls, because of wrong parenthesis. This also fixes the following static checker warning: drivers/usb/gadget/function/f_fs.c:3152 ffs_func_req_match() warn: always true condition '(((creq->wIndex)) >= 0) => (0-u16max >= 0)' Reported-by: Dan Carpenter Signed-off-by: Felix Hädicke Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/f_fs.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/gadget/function/f_fs.c b/drivers/usb/gadget/function/f_fs.c index e40d47d47d82..17989b72cdae 100644 --- a/drivers/usb/gadget/function/f_fs.c +++ b/drivers/usb/gadget/function/f_fs.c @@ -3225,11 +3225,11 @@ static bool ffs_func_req_match(struct usb_function *f, switch (creq->bRequestType & USB_RECIP_MASK) { case USB_RECIP_INTERFACE: - return ffs_func_revmap_intf(func, - le16_to_cpu(creq->wIndex) >= 0); + return (ffs_func_revmap_intf(func, + le16_to_cpu(creq->wIndex)) >= 0); case USB_RECIP_ENDPOINT: - return ffs_func_revmap_ep(func, - le16_to_cpu(creq->wIndex) >= 0); + return (ffs_func_revmap_ep(func, + le16_to_cpu(creq->wIndex)) >= 0); default: return (bool) (func->ffs->user_flags & FUNCTIONFS_ALL_CTRL_RECIP); -- cgit v1.2.3 From b0921d5c9ed6ffa8a4d6afc5ee5f136b87445f14 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 15 Nov 2016 11:13:16 +0100 Subject: mmc: sdhci-of-esdhc: fixup PRESENT_STATE read Since commit 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") the ESDHC driver is broken: mmc0: Card stuck in programming state! __mmc_switch mmc0: error -110 whilst initialising MMC card Since this commit __mmc_switch() uses ->card_busy(), which is sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the PRESENT_STATE register, specifically the DAT0 signal level bit. But the ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is required to make the driver work again. Signed-off-by: Michael Walle Fixes: 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") Acked-by: Yangbo Lu Acked-by: Adrian Hunter Cc: # v4.8+ Signed-off-by: Ulf Hansson --- drivers/mmc/host/sdhci-of-esdhc.c | 14 ++++++++++++++ drivers/mmc/host/sdhci.h | 1 + 2 files changed, 15 insertions(+) (limited to 'drivers') diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c index fb71c866eacc..1bb11e4a9fe5 100644 --- a/drivers/mmc/host/sdhci-of-esdhc.c +++ b/drivers/mmc/host/sdhci-of-esdhc.c @@ -66,6 +66,20 @@ static u32 esdhc_readl_fixup(struct sdhci_host *host, return ret; } } + /* + * The DAT[3:0] line signal levels and the CMD line signal level are + * not compatible with standard SDHC register. The line signal levels + * DAT[7:0] are at bits 31:24 and the command line signal level is at + * bit 23. All other bits are the same as in the standard SDHC + * register. + */ + if (spec_reg == SDHCI_PRESENT_STATE) { + ret = value & 0x000fffff; + ret |= (value >> 4) & SDHCI_DATA_LVL_MASK; + ret |= (value << 1) & SDHCI_CMD_LVL; + return ret; + } + ret = value; return ret; } diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 766df17fb7eb..2570455b219a 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -73,6 +73,7 @@ #define SDHCI_DATA_LVL_MASK 0x00F00000 #define SDHCI_DATA_LVL_SHIFT 20 #define SDHCI_DATA_0_LVL_MASK 0x00100000 +#define SDHCI_CMD_LVL 0x01000000 #define SDHCI_HOST_CONTROL 0x28 #define SDHCI_CTRL_LED 0x01 -- cgit v1.2.3 From 647f80a1f233bb66fc58fb25664d029e0f12f3ae Mon Sep 17 00:00:00 2001 From: Jaehoon Chung Date: Mon, 21 Nov 2016 10:51:48 +0900 Subject: mmc: dw_mmc: fix the error handling for dma operation When dma->start is failed,then it has to fall back to PIO mode for current transfer. But Host controller was already set to bits relevant to DMA operation. If needs to use the PIO mode, Host controller has to stop the DMA operation. (It's more stable than now.) When it occurred error, it's not running any request. Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support") Reported-by: Marek Szyprowski Signed-off-by: Jaehoon Chung Reviewed-by: Shawn Lin Cc: # v4.3+ Signed-off-by: Jaehoon Chung Signed-off-by: Ulf Hansson --- drivers/mmc/host/dw_mmc.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index 50a674be6655..df478ae72e23 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -1058,6 +1058,7 @@ static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data) spin_unlock_irqrestore(&host->irq_lock, irqflags); if (host->dma_ops->start(host, sg_len)) { + host->dma_ops->stop(host); /* We can't do DMA, try PIO for this one */ dev_dbg(host->dev, "%s: fall back to PIO mode for current transfer\n", -- cgit v1.2.3 From ec638db8cb9ddd5ca08b23f2835b6c9c15eb616d Mon Sep 17 00:00:00 2001 From: Jacob Pan Date: Mon, 14 Nov 2016 11:08:45 -0800 Subject: thermal/powerclamp: add back module device table Commit 3105f234e0aba43e44e277c20f9b32ee8add43d4 replaced module cpu id table with a cpu feature check, which is logically correct. But we need the module device table to allow module auto loading. Cc: stable@vger.kernel.org # 4.8 Fixes:3105f234 thermal/powerclamp: correct cpu support check Signed-off-by: Jacob Pan Signed-off-by: Zhang Rui --- drivers/thermal/intel_powerclamp.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/thermal/intel_powerclamp.c b/drivers/thermal/intel_powerclamp.c index 7a223074df3d..afada655f861 100644 --- a/drivers/thermal/intel_powerclamp.c +++ b/drivers/thermal/intel_powerclamp.c @@ -669,9 +669,16 @@ static struct thermal_cooling_device_ops powerclamp_cooling_ops = { .set_cur_state = powerclamp_set_cur_state, }; +static const struct x86_cpu_id __initconst intel_powerclamp_ids[] = { + { X86_VENDOR_INTEL, X86_FAMILY_ANY, X86_MODEL_ANY, X86_FEATURE_MWAIT }, + {} +}; +MODULE_DEVICE_TABLE(x86cpu, intel_powerclamp_ids); + static int __init powerclamp_probe(void) { - if (!boot_cpu_has(X86_FEATURE_MWAIT)) { + + if (!x86_match_cpu(intel_powerclamp_ids)) { pr_err("CPU does not support MWAIT"); return -ENODEV; } -- cgit v1.2.3 From 9713adc2a1a5488f4889c657a0c0ce0c16056d3c Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Mon, 21 Nov 2016 14:25:49 +0100 Subject: Revert "ACPI: Execute _PTS before system reboot" Revert commit 2c85025c75df (ACPI: Execute _PTS before system reboot) as it is reported to cause poweroff and reboot to hang on Dell Latitude E7250. Link: https://bugzilla.kernel.org/show_bug.cgi?id=187061 Reported-by: Gianpaolo Signed-off-by: Rafael J. Wysocki --- drivers/acpi/sleep.c | 29 ++++++----------------------- 1 file changed, 6 insertions(+), 23 deletions(-) (limited to 'drivers') diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c index 2b38c1bb0446..7a2e4d45b266 100644 --- a/drivers/acpi/sleep.c +++ b/drivers/acpi/sleep.c @@ -47,32 +47,15 @@ static void acpi_sleep_tts_switch(u32 acpi_state) } } -static void acpi_sleep_pts_switch(u32 acpi_state) -{ - acpi_status status; - - status = acpi_execute_simple_method(NULL, "\\_PTS", acpi_state); - if (ACPI_FAILURE(status) && status != AE_NOT_FOUND) { - /* - * OS can't evaluate the _PTS object correctly. Some warning - * message will be printed. But it won't break anything. - */ - printk(KERN_NOTICE "Failure in evaluating _PTS object\n"); - } -} - -static int sleep_notify_reboot(struct notifier_block *this, +static int tts_notify_reboot(struct notifier_block *this, unsigned long code, void *x) { acpi_sleep_tts_switch(ACPI_STATE_S5); - - acpi_sleep_pts_switch(ACPI_STATE_S5); - return NOTIFY_DONE; } -static struct notifier_block sleep_notifier = { - .notifier_call = sleep_notify_reboot, +static struct notifier_block tts_notifier = { + .notifier_call = tts_notify_reboot, .next = NULL, .priority = 0, }; @@ -916,9 +899,9 @@ int __init acpi_sleep_init(void) pr_info(PREFIX "(supports%s)\n", supported); /* - * Register the sleep_notifier to reboot notifier list so that the _TTS - * and _PTS object can also be evaluated when the system enters S5. + * Register the tts_notifier to reboot notifier list so that the _TTS + * object can also be evaluated when the system enters S5. */ - register_reboot_notifier(&sleep_notifier); + register_reboot_notifier(&tts_notifier); return 0; } -- cgit v1.2.3 From effb46b40f8053fd19698daf9e6b5833cabeba29 Mon Sep 17 00:00:00 2001 From: Mika Westerberg Date: Mon, 21 Nov 2016 15:33:07 +0200 Subject: watchdog: wdat_wdt: Select WATCHDOG_CORE The WDAT watchdog driver uses functionality provided by the watchdog timer core but it did not select it explicitly. This results following linker error when only WDAT_WDT is enabled in Kconfig: drivers/built-in.o: In function `wdat_wdt_probe': drivers/watchdog/wdat_wdt.c:444: undefined reference to `devm_watchdog_register_device' Fix this by explicitly selecting WATCHDOG_CORE when WDAT watchdog driver is enabled. Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog) Reported-by: Vegard Nossum Signed-off-by: Mika Westerberg Reviewed-by: Guenter Roeck Signed-off-by: Rafael J. Wysocki --- drivers/watchdog/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index 50dbaa805658..616a0b2d7768 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -155,6 +155,7 @@ config TANGOX_WATCHDOG config WDAT_WDT tristate "ACPI Watchdog Action Table (WDAT)" depends on ACPI + select WATCHDOG_CORE select ACPI_WATCHDOG help This driver adds support for systems with ACPI Watchdog Action -- cgit v1.2.3 From 7a79279e7186c4ac8b753cbd335ecc4ba81b5970 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 22 Nov 2016 13:56:54 +0000 Subject: drm/arm: hdlcd: fix plane base address update While testing HDMI with Xorg on the Juno board, I find that when Xorg starts up or shuts down, the display is shifted significantly to the right and wrapped in the active region. (No sync bars are visible.) The timings are correct, it behaves as if the start address has been shifted many pixels _into_ the framebuffer. This occurs whenever the display mode size is changed - using xrandr in Xorg shows that changing the resolution triggers the problem almost every time, but changing the refresh rate does not. Using devmem2 to disable and re-enable the HDLCD resolves the issue, and repeated disable/enable cycles do not make the issue re-appear. Further debugging shows that we try to update the controller configuration while enabled. Alwys ensure that the HDLCD is disabled prior to updating the controller timings, and use drm_crtc_vblank_off()/drm_crtc_vblank_on() so that DRM knows whether it can expect vblank interrupts. Signed-off-by: Russell King Signed-off-by: Liviu Dudau --- drivers/gpu/drm/arm/hdlcd_crtc.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/arm/hdlcd_crtc.c b/drivers/gpu/drm/arm/hdlcd_crtc.c index 48019ae22ddb..28341b32067f 100644 --- a/drivers/gpu/drm/arm/hdlcd_crtc.c +++ b/drivers/gpu/drm/arm/hdlcd_crtc.c @@ -150,15 +150,14 @@ static void hdlcd_crtc_enable(struct drm_crtc *crtc) clk_prepare_enable(hdlcd->clk); hdlcd_crtc_mode_set_nofb(crtc); hdlcd_write(hdlcd, HDLCD_REG_COMMAND, 1); + drm_crtc_vblank_on(crtc); } static void hdlcd_crtc_disable(struct drm_crtc *crtc) { struct hdlcd_drm_private *hdlcd = crtc_to_hdlcd_priv(crtc); - if (!crtc->state->active) - return; - + drm_crtc_vblank_off(crtc); hdlcd_write(hdlcd, HDLCD_REG_COMMAND, 0); clk_disable_unprepare(hdlcd->clk); } -- cgit v1.2.3 From 1ffb3c40ffb5c51bc39736409b11816c4260218e Mon Sep 17 00:00:00 2001 From: Benjamin Tissoires Date: Mon, 21 Nov 2016 11:48:39 +0100 Subject: HID: cp2112: make transfer buffers DMA capable Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove buffers allocated on the stack. Use a spinlock to prevent concurrent accesses to the buffer. Signed-off-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/hid-cp2112.c | 115 ++++++++++++++++++++++++++++++++--------------- 1 file changed, 79 insertions(+), 36 deletions(-) (limited to 'drivers') diff --git a/drivers/hid/hid-cp2112.c b/drivers/hid/hid-cp2112.c index 086d8a507157..60d30203a5fa 100644 --- a/drivers/hid/hid-cp2112.c +++ b/drivers/hid/hid-cp2112.c @@ -32,6 +32,11 @@ #include #include "hid-ids.h" +#define CP2112_REPORT_MAX_LENGTH 64 +#define CP2112_GPIO_CONFIG_LENGTH 5 +#define CP2112_GPIO_GET_LENGTH 2 +#define CP2112_GPIO_SET_LENGTH 3 + enum { CP2112_GPIO_CONFIG = 0x02, CP2112_GPIO_GET = 0x03, @@ -161,6 +166,8 @@ struct cp2112_device { atomic_t read_avail; atomic_t xfer_avail; struct gpio_chip gc; + u8 *in_out_buffer; + spinlock_t lock; }; static int gpio_push_pull = 0xFF; @@ -171,62 +178,86 @@ static int cp2112_gpio_direction_input(struct gpio_chip *chip, unsigned offset) { struct cp2112_device *dev = gpiochip_get_data(chip); struct hid_device *hdev = dev->hdev; - u8 buf[5]; + u8 *buf = dev->in_out_buffer; + unsigned long flags; int ret; + spin_lock_irqsave(&dev->lock, flags); + ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, - sizeof(buf), HID_FEATURE_REPORT, - HID_REQ_GET_REPORT); - if (ret != sizeof(buf)) { + CP2112_GPIO_CONFIG_LENGTH, HID_FEATURE_REPORT, + HID_REQ_GET_REPORT); + if (ret != CP2112_GPIO_CONFIG_LENGTH) { hid_err(hdev, "error requesting GPIO config: %d\n", ret); - return ret; + goto exit; } buf[1] &= ~(1 << offset); buf[2] = gpio_push_pull; - ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, sizeof(buf), - HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, + CP2112_GPIO_CONFIG_LENGTH, HID_FEATURE_REPORT, + HID_REQ_SET_REPORT); if (ret < 0) { hid_err(hdev, "error setting GPIO config: %d\n", ret); - return ret; + goto exit; } - return 0; + ret = 0; + +exit: + spin_unlock_irqrestore(&dev->lock, flags); + return ret <= 0 ? ret : -EIO; } static void cp2112_gpio_set(struct gpio_chip *chip, unsigned offset, int value) { struct cp2112_device *dev = gpiochip_get_data(chip); struct hid_device *hdev = dev->hdev; - u8 buf[3]; + u8 *buf = dev->in_out_buffer; + unsigned long flags; int ret; + spin_lock_irqsave(&dev->lock, flags); + buf[0] = CP2112_GPIO_SET; buf[1] = value ? 0xff : 0; buf[2] = 1 << offset; - ret = hid_hw_raw_request(hdev, CP2112_GPIO_SET, buf, sizeof(buf), - HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + ret = hid_hw_raw_request(hdev, CP2112_GPIO_SET, buf, + CP2112_GPIO_SET_LENGTH, HID_FEATURE_REPORT, + HID_REQ_SET_REPORT); if (ret < 0) hid_err(hdev, "error setting GPIO values: %d\n", ret); + + spin_unlock_irqrestore(&dev->lock, flags); } static int cp2112_gpio_get(struct gpio_chip *chip, unsigned offset) { struct cp2112_device *dev = gpiochip_get_data(chip); struct hid_device *hdev = dev->hdev; - u8 buf[2]; + u8 *buf = dev->in_out_buffer; + unsigned long flags; int ret; - ret = hid_hw_raw_request(hdev, CP2112_GPIO_GET, buf, sizeof(buf), - HID_FEATURE_REPORT, HID_REQ_GET_REPORT); - if (ret != sizeof(buf)) { + spin_lock_irqsave(&dev->lock, flags); + + ret = hid_hw_raw_request(hdev, CP2112_GPIO_GET, buf, + CP2112_GPIO_GET_LENGTH, HID_FEATURE_REPORT, + HID_REQ_GET_REPORT); + if (ret != CP2112_GPIO_GET_LENGTH) { hid_err(hdev, "error requesting GPIO values: %d\n", ret); - return ret; + ret = ret < 0 ? ret : -EIO; + goto exit; } - return (buf[1] >> offset) & 1; + ret = (buf[1] >> offset) & 1; + +exit: + spin_unlock_irqrestore(&dev->lock, flags); + + return ret; } static int cp2112_gpio_direction_output(struct gpio_chip *chip, @@ -234,27 +265,33 @@ static int cp2112_gpio_direction_output(struct gpio_chip *chip, { struct cp2112_device *dev = gpiochip_get_data(chip); struct hid_device *hdev = dev->hdev; - u8 buf[5]; + u8 *buf = dev->in_out_buffer; + unsigned long flags; int ret; + spin_lock_irqsave(&dev->lock, flags); + ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, - sizeof(buf), HID_FEATURE_REPORT, - HID_REQ_GET_REPORT); - if (ret != sizeof(buf)) { + CP2112_GPIO_CONFIG_LENGTH, HID_FEATURE_REPORT, + HID_REQ_GET_REPORT); + if (ret != CP2112_GPIO_CONFIG_LENGTH) { hid_err(hdev, "error requesting GPIO config: %d\n", ret); - return ret; + goto fail; } buf[1] |= 1 << offset; buf[2] = gpio_push_pull; - ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, sizeof(buf), - HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + ret = hid_hw_raw_request(hdev, CP2112_GPIO_CONFIG, buf, + CP2112_GPIO_CONFIG_LENGTH, HID_FEATURE_REPORT, + HID_REQ_SET_REPORT); if (ret < 0) { hid_err(hdev, "error setting GPIO config: %d\n", ret); - return ret; + goto fail; } + spin_unlock_irqrestore(&dev->lock, flags); + /* * Set gpio value when output direction is already set, * as specified in AN495, Rev. 0.2, cpt. 4.4 @@ -262,6 +299,10 @@ static int cp2112_gpio_direction_output(struct gpio_chip *chip, cp2112_gpio_set(chip, offset, value); return 0; + +fail: + spin_unlock_irqrestore(&dev->lock, flags); + return ret < 0 ? ret : -EIO; } static int cp2112_hid_get(struct hid_device *hdev, unsigned char report_number, @@ -1007,6 +1048,17 @@ static int cp2112_probe(struct hid_device *hdev, const struct hid_device_id *id) struct cp2112_smbus_config_report config; int ret; + dev = devm_kzalloc(&hdev->dev, sizeof(*dev), GFP_KERNEL); + if (!dev) + return -ENOMEM; + + dev->in_out_buffer = devm_kzalloc(&hdev->dev, CP2112_REPORT_MAX_LENGTH, + GFP_KERNEL); + if (!dev->in_out_buffer) + return -ENOMEM; + + spin_lock_init(&dev->lock); + ret = hid_parse(hdev); if (ret) { hid_err(hdev, "parse failed\n"); @@ -1063,12 +1115,6 @@ static int cp2112_probe(struct hid_device *hdev, const struct hid_device_id *id) goto err_power_normal; } - dev = kzalloc(sizeof(*dev), GFP_KERNEL); - if (!dev) { - ret = -ENOMEM; - goto err_power_normal; - } - hid_set_drvdata(hdev, (void *)dev); dev->hdev = hdev; dev->adap.owner = THIS_MODULE; @@ -1087,7 +1133,7 @@ static int cp2112_probe(struct hid_device *hdev, const struct hid_device_id *id) if (ret) { hid_err(hdev, "error registering i2c adapter\n"); - goto err_free_dev; + goto err_power_normal; } hid_dbg(hdev, "adapter registered\n"); @@ -1123,8 +1169,6 @@ err_gpiochip_remove: gpiochip_remove(&dev->gc); err_free_i2c: i2c_del_adapter(&dev->adap); -err_free_dev: - kfree(dev); err_power_normal: hid_hw_power(hdev, PM_HINT_NORMAL); err_hid_close: @@ -1149,7 +1193,6 @@ static void cp2112_remove(struct hid_device *hdev) */ hid_hw_close(hdev); hid_hw_stop(hdev); - kfree(dev); } static int cp2112_raw_event(struct hid_device *hdev, struct hid_report *report, -- cgit v1.2.3 From 061232f0d47fa10103f3efa3e890f002a930d902 Mon Sep 17 00:00:00 2001 From: Benjamin Tissoires Date: Mon, 21 Nov 2016 11:48:40 +0100 Subject: HID: lg: make transfer buffers DMA capable Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove buffers allocated on the stack. [jkosina@suse.cz: fix up second usage of hid_hw_raw_request(), spotted by 0day build bot] Signed-off-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/hid-lg.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/hid/hid-lg.c b/drivers/hid/hid-lg.c index 76f644deb0a7..c5c5fbe9d605 100644 --- a/drivers/hid/hid-lg.c +++ b/drivers/hid/hid-lg.c @@ -756,11 +756,16 @@ static int lg_probe(struct hid_device *hdev, const struct hid_device_id *id) /* Setup wireless link with Logitech Wii wheel */ if (hdev->product == USB_DEVICE_ID_LOGITECH_WII_WHEEL) { - unsigned char buf[] = { 0x00, 0xAF, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; + const unsigned char cbuf[] = { 0x00, 0xAF, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; + u8 *buf = kmemdup(cbuf, sizeof(cbuf), GFP_KERNEL); - ret = hid_hw_raw_request(hdev, buf[0], buf, sizeof(buf), - HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + if (!buf) { + ret = -ENOMEM; + goto err_free; + } + ret = hid_hw_raw_request(hdev, buf[0], buf, sizeof(cbuf), + HID_FEATURE_REPORT, HID_REQ_SET_REPORT); if (ret >= 0) { /* insert a little delay of 10 jiffies ~ 40ms */ wait_queue_head_t wait; @@ -772,9 +777,10 @@ static int lg_probe(struct hid_device *hdev, const struct hid_device_id *id) buf[1] = 0xB2; get_random_bytes(&buf[2], 2); - ret = hid_hw_raw_request(hdev, buf[0], buf, sizeof(buf), + ret = hid_hw_raw_request(hdev, buf[0], buf, sizeof(cbuf), HID_FEATURE_REPORT, HID_REQ_SET_REPORT); } + kfree(buf); } if (drv_data->quirks & LG_FF) -- cgit v1.2.3 From b7a87ad6775f3ed69e6573b91ed3c2f1338884ad Mon Sep 17 00:00:00 2001 From: Benjamin Tissoires Date: Mon, 21 Nov 2016 11:48:41 +0100 Subject: HID: magicmouse: make transfer buffers DMA capable Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove buffers allocated on the stack. Signed-off-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/hid-magicmouse.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/hid/hid-magicmouse.c b/drivers/hid/hid-magicmouse.c index d6fa496d0ca2..20b40ad26325 100644 --- a/drivers/hid/hid-magicmouse.c +++ b/drivers/hid/hid-magicmouse.c @@ -493,7 +493,8 @@ static int magicmouse_input_configured(struct hid_device *hdev, static int magicmouse_probe(struct hid_device *hdev, const struct hid_device_id *id) { - __u8 feature[] = { 0xd7, 0x01 }; + const u8 feature[] = { 0xd7, 0x01 }; + u8 *buf; struct magicmouse_sc *msc; struct hid_report *report; int ret; @@ -544,6 +545,12 @@ static int magicmouse_probe(struct hid_device *hdev, } report->size = 6; + buf = kmemdup(feature, sizeof(feature), GFP_KERNEL); + if (!buf) { + ret = -ENOMEM; + goto err_stop_hw; + } + /* * Some devices repond with 'invalid report id' when feature * report switching it into multitouch mode is sent to it. @@ -552,8 +559,9 @@ static int magicmouse_probe(struct hid_device *hdev, * but there seems to be no other way of switching the mode. * Thus the super-ugly hacky success check below. */ - ret = hid_hw_raw_request(hdev, feature[0], feature, sizeof(feature), + ret = hid_hw_raw_request(hdev, buf[0], buf, sizeof(feature), HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + kfree(buf); if (ret != -EIO && ret != sizeof(feature)) { hid_err(hdev, "unable to request touch data (%d)\n", ret); goto err_stop_hw; -- cgit v1.2.3 From 6dab07df555b652d8d989348b2ce04498d7f9a70 Mon Sep 17 00:00:00 2001 From: Benjamin Tissoires Date: Mon, 21 Nov 2016 11:48:42 +0100 Subject: HID: rmi: make transfer buffers DMA capable Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove buffers allocated on the stack. Signed-off-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/hid-rmi.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/hid/hid-rmi.c b/drivers/hid/hid-rmi.c index 9cd2ca34a6be..be89bcbf6a71 100644 --- a/drivers/hid/hid-rmi.c +++ b/drivers/hid/hid-rmi.c @@ -188,10 +188,16 @@ static int rmi_set_page(struct hid_device *hdev, u8 page) static int rmi_set_mode(struct hid_device *hdev, u8 mode) { int ret; - u8 txbuf[2] = {RMI_SET_RMI_MODE_REPORT_ID, mode}; + const u8 txbuf[2] = {RMI_SET_RMI_MODE_REPORT_ID, mode}; + u8 *buf; - ret = hid_hw_raw_request(hdev, RMI_SET_RMI_MODE_REPORT_ID, txbuf, + buf = kmemdup(txbuf, sizeof(txbuf), GFP_KERNEL); + if (!buf) + return -ENOMEM; + + ret = hid_hw_raw_request(hdev, RMI_SET_RMI_MODE_REPORT_ID, buf, sizeof(txbuf), HID_FEATURE_REPORT, HID_REQ_SET_REPORT); + kfree(buf); if (ret < 0) { dev_err(&hdev->dev, "unable to set rmi mode to %d (%d)\n", mode, ret); -- cgit v1.2.3 From d443a0aa3a291e5f78072f2fa464e03bc83fafad Mon Sep 17 00:00:00 2001 From: Song Hongyan Date: Tue, 15 Nov 2016 01:11:10 +0000 Subject: HID: hid-sensor-hub: clear memory to avoid random data When user tried to read some fields like hysteresis from IIO sysfs on some systems, it fails. The reason is that this field is a byte field and caller of sensor_hub_get_feature() passes a buffer of 4 bytes. Here the function sensor_hub_get_feature() copies the single byte from the report to the caller buffer and returns "1" as the number of bytes copied. So caller can use the return value. But this is done by multiple callers, so if we just change the sensor_hub_get_feature so that caller buffer is initialized with 0s then we don't to change all functions. Signed-off-by: Song Hongyan Acked-by: Jonathan Cameron Signed-off-by: Jiri Kosina --- drivers/hid/hid-sensor-hub.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/hid/hid-sensor-hub.c b/drivers/hid/hid-sensor-hub.c index c5c3d6111729..60875625cbdf 100644 --- a/drivers/hid/hid-sensor-hub.c +++ b/drivers/hid/hid-sensor-hub.c @@ -212,6 +212,7 @@ int sensor_hub_set_feature(struct hid_sensor_hub_device *hsdev, u32 report_id, __s32 value; int ret = 0; + memset(buffer, 0, buffer_size); mutex_lock(&data->mutex); report = sensor_hub_report(report_id, hsdev->hdev, HID_FEATURE_REPORT); if (!report || (field_index >= report->maxfield)) { -- cgit v1.2.3 From 1db4496f167bcc7c6541d449355ade2e7d339d52 Mon Sep 17 00:00:00 2001 From: Peter Wu Date: Wed, 23 Nov 2016 02:22:24 +0100 Subject: drm/amdgpu: fix power state when port pm is unavailable MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When PCIe port PM is not enabled (system BIOS is pre-2015 or the pcie_port_pm=off parameter is set), legacy ATPX PM should still be marked as supported. Otherwise the GPU can fail to power on after runtime suspend. This affected a Dell Inspiron 5548. Ideally the BIOS date in the PCI core is lowered to 2013 (the first year where hybrid graphics platforms using power resources was introduced), but that seems more risky at this point and would not solve the pcie_port_pm=off issue. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505 Reported-and-tested-by: Nayan Deshmukh Signed-off-by: Peter Wu Signed-off-by: Alex Deucher Cc: # 4.8+ Acked-by: Christian König Reviewed-by: Alex Deucher --- drivers/gpu/drm/amd/amdgpu/amdgpu_atpx_handler.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_atpx_handler.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_atpx_handler.c index dae35a96a694..02ca5dd978f6 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_atpx_handler.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_atpx_handler.c @@ -34,6 +34,7 @@ struct amdgpu_atpx { static struct amdgpu_atpx_priv { bool atpx_detected; + bool bridge_pm_usable; /* handle for device - and atpx */ acpi_handle dhandle; acpi_handle other_handle; @@ -205,7 +206,11 @@ static int amdgpu_atpx_validate(struct amdgpu_atpx *atpx) atpx->is_hybrid = false; if (valid_bits & ATPX_MS_HYBRID_GFX_SUPPORTED) { printk("ATPX Hybrid Graphics\n"); - atpx->functions.power_cntl = false; + /* + * Disable legacy PM methods only when pcie port PM is usable, + * otherwise the device might fail to power off or power on. + */ + atpx->functions.power_cntl = !amdgpu_atpx_priv.bridge_pm_usable; atpx->is_hybrid = true; } @@ -480,6 +485,7 @@ static int amdgpu_atpx_power_state(enum vga_switcheroo_client_id id, */ static bool amdgpu_atpx_pci_probe_handle(struct pci_dev *pdev) { + struct pci_dev *parent_pdev = pci_upstream_bridge(pdev); acpi_handle dhandle, atpx_handle; acpi_status status; @@ -494,6 +500,7 @@ static bool amdgpu_atpx_pci_probe_handle(struct pci_dev *pdev) } amdgpu_atpx_priv.dhandle = dhandle; amdgpu_atpx_priv.atpx.handle = atpx_handle; + amdgpu_atpx_priv.bridge_pm_usable = parent_pdev && parent_pdev->bridge_d3; return true; } -- cgit v1.2.3 From d3ac31f3b4bf9fade93d69770cb9c34912e017be Mon Sep 17 00:00:00 2001 From: Peter Wu Date: Wed, 23 Nov 2016 02:22:25 +0100 Subject: drm/radeon: fix power state when port pm is unavailable (v2) When PCIe port PM is not enabled (system BIOS is pre-2015 or the pcie_port_pm=off parameter is set), legacy ATPX PM should still be marked as supported. Otherwise the GPU can fail to power on after runtime suspend. This affected a Dell Inspiron 5548. Ideally the BIOS date in the PCI core is lowered to 2013 (the first year where hybrid graphics platforms using power resources was introduced), but that seems more risky at this point and would not solve the pcie_port_pm=off issue. v2: agd: fix typo Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505 Signed-off-by: Peter Wu Signed-off-by: Alex Deucher Cc: # 4.8+ Reviewed-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_atpx_handler.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_atpx_handler.c b/drivers/gpu/drm/radeon/radeon_atpx_handler.c index 2fdcd04bc93f..4129b12521a6 100644 --- a/drivers/gpu/drm/radeon/radeon_atpx_handler.c +++ b/drivers/gpu/drm/radeon/radeon_atpx_handler.c @@ -34,6 +34,7 @@ struct radeon_atpx { static struct radeon_atpx_priv { bool atpx_detected; + bool bridge_pm_usable; /* handle for device - and atpx */ acpi_handle dhandle; struct radeon_atpx atpx; @@ -203,7 +204,11 @@ static int radeon_atpx_validate(struct radeon_atpx *atpx) atpx->is_hybrid = false; if (valid_bits & ATPX_MS_HYBRID_GFX_SUPPORTED) { printk("ATPX Hybrid Graphics\n"); - atpx->functions.power_cntl = false; + /* + * Disable legacy PM methods only when pcie port PM is usable, + * otherwise the device might fail to power off or power on. + */ + atpx->functions.power_cntl = !radeon_atpx_priv.bridge_pm_usable; atpx->is_hybrid = true; } @@ -474,6 +479,7 @@ static int radeon_atpx_power_state(enum vga_switcheroo_client_id id, */ static bool radeon_atpx_pci_probe_handle(struct pci_dev *pdev) { + struct pci_dev *parent_pdev = pci_upstream_bridge(pdev); acpi_handle dhandle, atpx_handle; acpi_status status; @@ -487,6 +493,7 @@ static bool radeon_atpx_pci_probe_handle(struct pci_dev *pdev) radeon_atpx_priv.dhandle = dhandle; radeon_atpx_priv.atpx.handle = atpx_handle; + radeon_atpx_priv.bridge_pm_usable = parent_pdev && parent_pdev->bridge_d3; return true; } -- cgit v1.2.3 From 22a1e7783e173ab3d86018eb590107d68df46c11 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 17 Nov 2016 10:49:31 +0100 Subject: xc2028: Fix use-after-free bug properly The commit 8dfbcc4351a0 ("[media] xc2028: avoid use after free") tried to address the reported use-after-free by clearing the reference. However, it's clearing the wrong pointer; it sets NULL to priv->ctrl.fname, but it's anyway overwritten by the next line memcpy(&priv->ctrl, p, sizeof(priv->ctrl)). OTOH, the actual code accessing the freed string is the strcmp() call with priv->fname: if (!firmware_name[0] && p->fname && priv->fname && strcmp(p->fname, priv->fname)) free_firmware(priv); where priv->fname points to the previous file name, and this was already freed by kfree(). For fixing the bug properly, this patch does the following: - Keep the copy of firmware file name in only priv->fname, priv->ctrl.fname isn't changed; - The allocation is done only when the firmware gets loaded; - The kfree() is called in free_firmware() commonly Fixes: commit 8dfbcc4351a0 ('[media] xc2028: avoid use after free') Cc: Signed-off-by: Takashi Iwai Signed-off-by: Mauro Carvalho Chehab --- drivers/media/tuners/tuner-xc2028.c | 37 ++++++++++++++++--------------------- 1 file changed, 16 insertions(+), 21 deletions(-) (limited to 'drivers') diff --git a/drivers/media/tuners/tuner-xc2028.c b/drivers/media/tuners/tuner-xc2028.c index 317ef63ee789..8d96a22647b3 100644 --- a/drivers/media/tuners/tuner-xc2028.c +++ b/drivers/media/tuners/tuner-xc2028.c @@ -281,6 +281,14 @@ static void free_firmware(struct xc2028_data *priv) int i; tuner_dbg("%s called\n", __func__); + /* free allocated f/w string */ + if (priv->fname != firmware_name) + kfree(priv->fname); + priv->fname = NULL; + + priv->state = XC2028_NO_FIRMWARE; + memset(&priv->cur_fw, 0, sizeof(priv->cur_fw)); + if (!priv->firm) return; @@ -291,9 +299,6 @@ static void free_firmware(struct xc2028_data *priv) priv->firm = NULL; priv->firm_size = 0; - priv->state = XC2028_NO_FIRMWARE; - - memset(&priv->cur_fw, 0, sizeof(priv->cur_fw)); } static int load_all_firmwares(struct dvb_frontend *fe, @@ -884,9 +889,8 @@ read_not_reliable: return 0; fail: - priv->state = XC2028_NO_FIRMWARE; + free_firmware(priv); - memset(&priv->cur_fw, 0, sizeof(priv->cur_fw)); if (retry_count < 8) { msleep(50); retry_count++; @@ -1332,11 +1336,8 @@ static int xc2028_dvb_release(struct dvb_frontend *fe) mutex_lock(&xc2028_list_mutex); /* only perform final cleanup if this is the last instance */ - if (hybrid_tuner_report_instance_count(priv) == 1) { + if (hybrid_tuner_report_instance_count(priv) == 1) free_firmware(priv); - kfree(priv->ctrl.fname); - priv->ctrl.fname = NULL; - } if (priv) hybrid_tuner_release_state(priv); @@ -1399,19 +1400,8 @@ static int xc2028_set_config(struct dvb_frontend *fe, void *priv_cfg) /* * Copy the config data. - * For the firmware name, keep a local copy of the string, - * in order to avoid troubles during device release. */ - kfree(priv->ctrl.fname); - priv->ctrl.fname = NULL; memcpy(&priv->ctrl, p, sizeof(priv->ctrl)); - if (p->fname) { - priv->ctrl.fname = kstrdup(p->fname, GFP_KERNEL); - if (priv->ctrl.fname == NULL) { - rc = -ENOMEM; - goto unlock; - } - } /* * If firmware name changed, frees firmware. As free_firmware will @@ -1426,10 +1416,15 @@ static int xc2028_set_config(struct dvb_frontend *fe, void *priv_cfg) if (priv->state == XC2028_NO_FIRMWARE) { if (!firmware_name[0]) - priv->fname = priv->ctrl.fname; + priv->fname = kstrdup(p->fname, GFP_KERNEL); else priv->fname = firmware_name; + if (!priv->fname) { + rc = -ENOMEM; + goto unlock; + } + rc = request_firmware_nowait(THIS_MODULE, 1, priv->fname, priv->i2c_props.adap->dev.parent, -- cgit v1.2.3 From ffa54a238c69184414a8f3dc35a18aed875290e7 Mon Sep 17 00:00:00 2001 From: Kirill Esipov Date: Mon, 21 Nov 2016 19:53:31 +0300 Subject: net: phy: micrel: fix KSZ8041FTL supported value Fix setting of SUPPORTED_FIBRE bit as it was not present in features of KSZ8041. Signed-off-by: Kirill Esipov Signed-off-by: David S. Miller --- drivers/net/phy/micrel.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index 081df68d2ce1..ea92d524d5a8 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -318,12 +318,12 @@ static int ksz8041_config_init(struct phy_device *phydev) /* Limit supported and advertised modes in fiber mode */ if (of_property_read_bool(of_node, "micrel,fiber-mode")) { phydev->dev_flags |= MICREL_PHY_FXEN; - phydev->supported &= SUPPORTED_FIBRE | - SUPPORTED_100baseT_Full | + phydev->supported &= SUPPORTED_100baseT_Full | SUPPORTED_100baseT_Half; - phydev->advertising &= ADVERTISED_FIBRE | - ADVERTISED_100baseT_Full | + phydev->supported |= SUPPORTED_FIBRE; + phydev->advertising &= ADVERTISED_100baseT_Full | ADVERTISED_100baseT_Half; + phydev->advertising |= ADVERTISED_FIBRE; phydev->autoneg = AUTONEG_DISABLE; } -- cgit v1.2.3 From c3891fa2543cbab26093f5e425b8a50cd6837f16 Mon Sep 17 00:00:00 2001 From: Gao Feng Date: Tue, 22 Nov 2016 09:54:36 +0800 Subject: driver: macvlan: Check if need rollback multicast setting in macvlan_open When dev_set_promiscuity failed in macvlan_open, it always invokes dev_set_allmulti without checking if necessary. Now check the IFF_ALLMULTI flag firstly before rollback the multicast setting in the error handler. Signed-off-by: Gao Feng Signed-off-by: David S. Miller --- drivers/net/macvlan.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/macvlan.c b/drivers/net/macvlan.c index d2d6f12a112f..26d6f0bbe14b 100644 --- a/drivers/net/macvlan.c +++ b/drivers/net/macvlan.c @@ -623,7 +623,8 @@ hash_add: return 0; clear_multi: - dev_set_allmulti(lowerdev, -1); + if (dev->flags & IFF_ALLMULTI) + dev_set_allmulti(lowerdev, -1); del_unicast: dev_uc_del(lowerdev, dev->dev_addr); out: -- cgit v1.2.3 From 57aac71b3e9ed890cf2219dd980c36f859b43d6a Mon Sep 17 00:00:00 2001 From: Christophe Jaillet Date: Tue, 22 Nov 2016 06:14:40 +0100 Subject: bnxt_en: Fix a VXLAN vs GENEVE issue Knowing that: #define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0) #define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0) and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not trigger. Replace the bit test that overlap by an equality test, just as in 'bnxt_hwrm_tunnel_dst_port_free()' above. Signed-off-by: Christophe JAILLET Acked-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnxt/bnxt.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt.c b/drivers/net/ethernet/broadcom/bnxt/bnxt.c index e18635b2a002..e41d8bd094ae 100644 --- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c +++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c @@ -3210,11 +3210,17 @@ static int bnxt_hwrm_tunnel_dst_port_alloc(struct bnxt *bp, __be16 port, goto err_out; } - if (tunnel_type & TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_VXLAN) + switch (tunnel_type) { + case TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_VXLAN: bp->vxlan_fw_dst_port_id = resp->tunnel_dst_port_id; - - else if (tunnel_type & TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE) + break; + case TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE: bp->nge_fw_dst_port_id = resp->tunnel_dst_port_id; + break; + default: + break; + } + err_out: mutex_unlock(&bp->hwrm_cmd_lock); return rc; -- cgit v1.2.3 From b6e01232e25629907df9db19f25da7d4e8f5b589 Mon Sep 17 00:00:00 2001 From: Tariq Toukan Date: Tue, 22 Nov 2016 16:20:39 +0200 Subject: net/mlx4_en: Free netdev resources under state lock Make sure mlx4_en_free_resources is called under the netdev state lock. This is needed since RCU dereference of XDP prog should be protected. Fixes: 326fe02d1ed6 ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock") Signed-off-by: Tariq Toukan Reported-by: Sagi Grimberg CC: Brenden Blanco Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index 3a47e83d3e07..a60f635da78b 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -129,6 +129,9 @@ static enum mlx4_net_trans_rule_id mlx4_ip_proto_to_trans_rule_id(u8 ip_proto) } }; +/* Must not acquire state_lock, as its corresponding work_sync + * is done under it. + */ static void mlx4_en_filter_work(struct work_struct *work) { struct mlx4_en_filter *filter = container_of(work, @@ -2189,13 +2192,13 @@ void mlx4_en_destroy_netdev(struct net_device *dev) mutex_lock(&mdev->state_lock); mdev->pndev[priv->port] = NULL; mdev->upper[priv->port] = NULL; - mutex_unlock(&mdev->state_lock); #ifdef CONFIG_RFS_ACCEL mlx4_en_cleanup_filters(priv); #endif mlx4_en_free_resources(priv); + mutex_unlock(&mdev->state_lock); kfree(priv->tx_ring); kfree(priv->tx_cq); -- cgit v1.2.3 From 1ee6f347f81925fa8f3816e69ca1b49021f37850 Mon Sep 17 00:00:00 2001 From: Bibby Hsieh Date: Tue, 18 Oct 2016 16:23:59 +0800 Subject: drm/mediatek: fix a typo of DISP_OD_CFG to OD_RELAYMODE If we want to set the hardware OD to relay mode, we have to set DISP_OD_CFG register rather than OD_RELAYMODE; otherwise, the system will access the wrong address. Change-Id: Ifb9bb4caa63df906437d48b5d5326b6d04ea332a Fixes: 7216436420414144646f5d8343d061355fd23483 ("drm/mediatek: set mt8173 dithering function") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Bibby Hsieh Acked-by: CK Hu --- drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c index df33b3ca6ffd..48cc01fd20c7 100644 --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c @@ -123,7 +123,7 @@ static void mtk_od_config(struct mtk_ddp_comp *comp, unsigned int w, unsigned int bpc) { writel(w << 16 | h, comp->regs + DISP_OD_SIZE); - writel(OD_RELAYMODE, comp->regs + OD_RELAYMODE); + writel(OD_RELAYMODE, comp->regs + DISP_OD_CFG); mtk_dither_set(comp, bpc, DISP_OD_CFG); } -- cgit v1.2.3 From f6c872397028837c80685ee96c4011c62abe9a73 Mon Sep 17 00:00:00 2001 From: Jitao Shi Date: Wed, 16 Nov 2016 11:20:54 +0800 Subject: drm/mediatek: fixed the calc method of data rate per lane Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e. Tlpx, Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP mode, those signals will cause h-time larger than normal and reduce FPS. So need to multiply a coefficient to offset the extra signal's effect. coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+ Ths_trail+Ths_exit)/(htotal*bpp/lane_number) Signed-off-by: Jitao Shi Reviewed-by: Daniel Kurtz --- drivers/gpu/drm/mediatek/mtk_dsi.c | 64 ++++++++++++++++++++++++++++---------- 1 file changed, 48 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c index 28b2044ed9f2..eaa5a2240c0c 100644 --- a/drivers/gpu/drm/mediatek/mtk_dsi.c +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c @@ -86,7 +86,7 @@ #define DSI_PHY_TIMECON0 0x110 #define LPX (0xff << 0) -#define HS_PRPR (0xff << 8) +#define HS_PREP (0xff << 8) #define HS_ZERO (0xff << 16) #define HS_TRAIL (0xff << 24) @@ -102,10 +102,16 @@ #define CLK_TRAIL (0xff << 24) #define DSI_PHY_TIMECON3 0x11c -#define CLK_HS_PRPR (0xff << 0) +#define CLK_HS_PREP (0xff << 0) #define CLK_HS_POST (0xff << 8) #define CLK_HS_EXIT (0xff << 16) +#define T_LPX 5 +#define T_HS_PREP 6 +#define T_HS_TRAIL 8 +#define T_HS_EXIT 7 +#define T_HS_ZERO 10 + #define NS_TO_CYCLE(n, c) ((n) / (c) + (((n) % (c)) ? 1 : 0)) struct phy; @@ -161,20 +167,18 @@ static void mtk_dsi_mask(struct mtk_dsi *dsi, u32 offset, u32 mask, u32 data) static void dsi_phy_timconfig(struct mtk_dsi *dsi) { u32 timcon0, timcon1, timcon2, timcon3; - unsigned int ui, cycle_time; - unsigned int lpx; + u32 ui, cycle_time; ui = 1000 / dsi->data_rate + 0x01; cycle_time = 8000 / dsi->data_rate + 0x01; - lpx = 5; - timcon0 = (8 << 24) | (0xa << 16) | (0x6 << 8) | lpx; - timcon1 = (7 << 24) | (5 * lpx << 16) | ((3 * lpx) / 2) << 8 | - (4 * lpx); + timcon0 = T_LPX | T_HS_PREP << 8 | T_HS_ZERO << 16 | T_HS_TRAIL << 24; + timcon1 = 4 * T_LPX | (3 * T_LPX / 2) << 8 | 5 * T_LPX << 16 | + T_HS_EXIT << 24; timcon2 = ((NS_TO_CYCLE(0x64, cycle_time) + 0xa) << 24) | (NS_TO_CYCLE(0x150, cycle_time) << 16); - timcon3 = (2 * lpx) << 16 | NS_TO_CYCLE(80 + 52 * ui, cycle_time) << 8 | - NS_TO_CYCLE(0x40, cycle_time); + timcon3 = NS_TO_CYCLE(0x40, cycle_time) | (2 * T_LPX) << 16 | + NS_TO_CYCLE(80 + 52 * ui, cycle_time) << 8; writel(timcon0, dsi->regs + DSI_PHY_TIMECON0); writel(timcon1, dsi->regs + DSI_PHY_TIMECON1); @@ -202,19 +206,47 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) { struct device *dev = dsi->dev; int ret; + u64 pixel_clock, total_bits; + u32 htotal, htotal_bits, bit_per_pixel, overhead_cycles, overhead_bits; if (++dsi->refcount != 1) return 0; + switch (dsi->format) { + case MIPI_DSI_FMT_RGB565: + bit_per_pixel = 16; + break; + case MIPI_DSI_FMT_RGB666_PACKED: + bit_per_pixel = 18; + break; + case MIPI_DSI_FMT_RGB666: + case MIPI_DSI_FMT_RGB888: + default: + bit_per_pixel = 24; + break; + } + /** - * data_rate = (pixel_clock / 1000) * pixel_dipth * mipi_ratio; - * pixel_clock unit is Khz, data_rata unit is MHz, so need divide 1000. - * mipi_ratio is mipi clk coefficient for balance the pixel clk in mipi. - * we set mipi_ratio is 1.05. + * vm.pixelclock is in kHz, pixel_clock unit is Hz, so multiply by 1000 + * htotal_time = htotal * byte_per_pixel / num_lanes + * overhead_time = lpx + hs_prepare + hs_zero + hs_trail + hs_exit + * mipi_ratio = (htotal_time + overhead_time) / htotal_time + * data_rate = pixel_clock * bit_per_pixel * mipi_ratio / num_lanes; */ - dsi->data_rate = dsi->vm.pixelclock * 3 * 21 / (1 * 1000 * 10); + pixel_clock = dsi->vm.pixelclock * 1000; + htotal = dsi->vm.hactive + dsi->vm.hback_porch + dsi->vm.hfront_porch + + dsi->vm.hsync_len; + htotal_bits = htotal * bit_per_pixel; + + overhead_cycles = T_LPX + T_HS_PREP + T_HS_ZERO + T_HS_TRAIL + + T_HS_EXIT; + overhead_bits = overhead_cycles * dsi->lanes * 8; + total_bits = htotal_bits + overhead_bits; + + dsi->data_rate = DIV_ROUND_UP_ULL(pixel_clock * total_bits, + htotal * dsi->lanes); - ret = clk_set_rate(dsi->hs_clk, dsi->data_rate * 1000000); + ret = clk_set_rate(dsi->hs_clk, dsi->data_rate); if (ret < 0) { dev_err(dev, "Failed to set data rate: %d\n", ret); goto err_refcount; -- cgit v1.2.3 From 5ad45307d990020b25a8f7486178b6e033790f70 Mon Sep 17 00:00:00 2001 From: Matthias Brugger Date: Fri, 18 Nov 2016 11:06:10 +0100 Subject: drm/mediatek: fix null pointer dereference The probe function requests the interrupt before initializing the ddp component. Which leads to a null pointer dereference at boot. Fix this by requesting the interrput after all components got initialized properly. Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.") Signed-off-by: Matthias Brugger Change-Id: I57193a7ab554dfb37c35a455900689333adf511c --- drivers/gpu/drm/mediatek/mtk_disp_ovl.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/mediatek/mtk_disp_ovl.c b/drivers/gpu/drm/mediatek/mtk_disp_ovl.c index f75c5b5a536c..c70310206ac5 100644 --- a/drivers/gpu/drm/mediatek/mtk_disp_ovl.c +++ b/drivers/gpu/drm/mediatek/mtk_disp_ovl.c @@ -251,13 +251,6 @@ static int mtk_disp_ovl_probe(struct platform_device *pdev) if (irq < 0) return irq; - ret = devm_request_irq(dev, irq, mtk_disp_ovl_irq_handler, - IRQF_TRIGGER_NONE, dev_name(dev), priv); - if (ret < 0) { - dev_err(dev, "Failed to request irq %d: %d\n", irq, ret); - return ret; - } - comp_id = mtk_ddp_comp_get_id(dev->of_node, MTK_DISP_OVL); if (comp_id < 0) { dev_err(dev, "Failed to identify by alias: %d\n", comp_id); @@ -273,6 +266,13 @@ static int mtk_disp_ovl_probe(struct platform_device *pdev) platform_set_drvdata(pdev, priv); + ret = devm_request_irq(dev, irq, mtk_disp_ovl_irq_handler, + IRQF_TRIGGER_NONE, dev_name(dev), priv); + if (ret < 0) { + dev_err(dev, "Failed to request irq %d: %d\n", irq, ret); + return ret; + } + ret = component_add(dev, &mtk_disp_ovl_component_ops); if (ret) dev_err(dev, "Failed to add component: %d\n", ret); -- cgit v1.2.3 From 2bf413d56b7de72ab800a6edb009177e5669b929 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 18 Nov 2016 19:40:04 +0000 Subject: i2c: designware: report short transfers Rather than reporting success for a short transfer due to interrupt latency, report an error both to the caller, as well as to the kernel log. Signed-off-by: Russell King Reviewed-by: Mika Westerberg Acked-by: Jarkko Nikula Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-core.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 11e866d05368..066a2ba6aeda 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -758,7 +758,7 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) } /* no error */ - if (likely(!dev->cmd_err)) { + if (likely(!dev->cmd_err && !dev->status)) { ret = num; goto done; } @@ -768,6 +768,11 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) ret = i2c_dw_handle_tx_abort(dev); goto done; } + + if (dev->status) + dev_err(dev->dev, + "transfer terminated early - interrupt latency too high?\n"); + ret = -EIO; done: -- cgit v1.2.3 From 4d6d5f1d08d2138dc43b28966eb6200e3db2e623 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 18 Nov 2016 19:40:10 +0000 Subject: i2c: designware: fix rx fifo depth tracking When loading the TX fifo to receive bytes on the I2C bus, we incorrectly count the number of bytes: rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR); while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) { if (rx_limit - dev->rx_outstanding <= 0) break; rx_limit--; dev->rx_outstanding++; } DW_IC_RXFLR indicates how many bytes are available to be read in the FIFO, dev->rx_fifo_depth is the FIFO size, and dev->rx_outstanding is the number of bytes that we've requested to be read so far, but which have not been read. Firstly, increasing dev->rx_outstanding and decreasing rx_limit and then comparing them results in each byte consuming "two" bytes in this tracking, so this is obviously wrong. Secondly, the number of bytes that _could_ be received into the FIFO at any time is the number of bytes we have so far requested but not yet read from the FIFO - in other words dev->rx_outstanding. So, in order to request enough bytes to fill the RX FIFO, we need to request dev->rx_fifo_depth - dev->rx_outstanding bytes. Modifying the code thusly results in us reaching the maximum number of bytes outstanding each time we queue more "receive" operations, provided the transfer allows that to happen. Signed-off-by: Russell King Reviewed-by: Mika Westerberg Acked-by: Jarkko Nikula Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 066a2ba6aeda..c53058d6139c 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -611,7 +611,7 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) if (msgs[dev->msg_write_idx].flags & I2C_M_RD) { /* avoid rx buffer overrun */ - if (rx_limit - dev->rx_outstanding <= 0) + if (dev->rx_outstanding >= dev->rx_fifo_depth) break; dw_writel(dev, cmd | 0x100, DW_IC_DATA_CMD); -- cgit v1.2.3 From 867d1212bf3c53dc057f7bca72155048cc51d18c Mon Sep 17 00:00:00 2001 From: Andy Gospodarek Date: Tue, 22 Nov 2016 13:14:08 -0500 Subject: bnxt: do not busy-poll when link is down When busy polling while a link is down (during a link-flap test), TX timeouts were observed as well as the following messages in the ring buffer: bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51 bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1 bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51 bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1 These were resolved by checking for link status and returning if link was not up. Signed-off-by: Andy Gospodarek Signed-off-by: Michael Chan Tested-by: Rob Miller Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnxt/bnxt.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt.c b/drivers/net/ethernet/broadcom/bnxt/bnxt.c index e41d8bd094ae..ee1a803aa11a 100644 --- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c +++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c @@ -1811,6 +1811,9 @@ static int bnxt_busy_poll(struct napi_struct *napi) if (atomic_read(&bp->intr_sem) != 0) return LL_FLUSH_FAILED; + if (!bp->link_info.link_up) + return LL_FLUSH_FAILED; + if (!bnxt_lock_poll(bnapi)) return LL_FLUSH_BUSY; -- cgit v1.2.3 From 76da8706d90d8641eeb9b8e579942ed80b6c0880 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 22 Nov 2016 11:40:58 -0800 Subject: net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change In case the link change and EEE is enabled or disabled, always try to re-negotiate this with the link partner. Fixes: 450b05c15f9c ("net: dsa: bcm_sf2: add support for controlling EEE") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/dsa/bcm_sf2.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c index e3ee27ce13dd..9ec33b51a0ed 100644 --- a/drivers/net/dsa/bcm_sf2.c +++ b/drivers/net/dsa/bcm_sf2.c @@ -588,6 +588,7 @@ static void bcm_sf2_sw_adjust_link(struct dsa_switch *ds, int port, struct phy_device *phydev) { struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); + struct ethtool_eee *p = &priv->port_sts[port].eee; u32 id_mode_dis = 0, port_mode; const char *str = NULL; u32 reg; @@ -662,6 +663,9 @@ force_link: reg |= DUPLX_MODE; core_writel(priv, reg, CORE_STS_OVERRIDE_GMIIP_PORT(port)); + + if (!phydev->is_pseudo_fixed_link) + p->eee_enabled = bcm_sf2_eee_init(ds, port, phydev); } static void bcm_sf2_sw_fixed_link_update(struct dsa_switch *ds, int port, -- cgit v1.2.3 From d74200024009c8d974c7484446c9eb1622408a17 Mon Sep 17 00:00:00 2001 From: Arvind Yadav Date: Wed, 19 Oct 2016 15:34:16 +0530 Subject: gpu/drm/exynos/exynos_hdmi - Unmap region obtained by of_iomap Free memory mapping, if hdmi_probe is not successful. Signed-off-by: Arvind Yadav Signed-off-by: Inki Dae Signed-off-by: Dave Airlie --- drivers/gpu/drm/exynos/exynos_hdmi.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/exynos/exynos_hdmi.c b/drivers/gpu/drm/exynos/exynos_hdmi.c index e8fb6ef947ee..38eaa63afb31 100644 --- a/drivers/gpu/drm/exynos/exynos_hdmi.c +++ b/drivers/gpu/drm/exynos/exynos_hdmi.c @@ -1907,6 +1907,8 @@ err_disable_pm_runtime: err_hdmiphy: if (hdata->hdmiphy_port) put_device(&hdata->hdmiphy_port->dev); + if (hdata->regs_hdmiphy) + iounmap(hdata->regs_hdmiphy); err_ddc: put_device(&hdata->ddc_adpt->dev); @@ -1929,6 +1931,9 @@ static int hdmi_remove(struct platform_device *pdev) if (hdata->hdmiphy_port) put_device(&hdata->hdmiphy_port->dev); + if (hdata->regs_hdmiphy) + iounmap(hdata->regs_hdmiphy); + put_device(&hdata->ddc_adpt->dev); return 0; -- cgit v1.2.3 From d29ccdb3f0e5dccb170200c9f3d573eaa5af261b Mon Sep 17 00:00:00 2001 From: Paul Burton Date: Fri, 14 Oct 2016 10:17:31 +0100 Subject: mfd: syscon: Support native-endian regmaps The regmap devicetree binding documentation states that a native-endian property should be supported as well as big-endian & little-endian, however syscon in its duplication of the parsing of these properties omits support for native-endian. Fix this by setting REGMAP_ENDIAN_NATIVE when a native-endian property is found. Signed-off-by: Paul Burton Cc: Lee Jones Cc: Arnd Bergmann Cc: Guenter Roeck Cc: Ralf Baechle Cc: linux-mips@linux-mips.org Signed-off-by: Lee Jones --- drivers/mfd/syscon.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mfd/syscon.c b/drivers/mfd/syscon.c index 2f2225e845ef..b93fe4c4957a 100644 --- a/drivers/mfd/syscon.c +++ b/drivers/mfd/syscon.c @@ -73,8 +73,10 @@ static struct syscon *of_syscon_register(struct device_node *np) /* Parse the device's DT node for an endianness specification */ if (of_property_read_bool(np, "big-endian")) syscon_config.val_format_endian = REGMAP_ENDIAN_BIG; - else if (of_property_read_bool(np, "little-endian")) + else if (of_property_read_bool(np, "little-endian")) syscon_config.val_format_endian = REGMAP_ENDIAN_LITTLE; + else if (of_property_read_bool(np, "native-endian")) + syscon_config.val_format_endian = REGMAP_ENDIAN_NATIVE; /* * search for reg-io-width property in DT. If it is not provided, -- cgit v1.2.3 From 3cfc43df7af0533b39b97bb03980e02e9716fc52 Mon Sep 17 00:00:00 2001 From: Viresh Kumar Date: Fri, 16 Sep 2016 08:56:59 +0530 Subject: mfd: wm8994-core: Disable regulators before removing them The order in which resources were freed in wm8994_device_exit() isn't correct. The regulators are removed before they are disabled. Fix it by reordering code a bit, which makes it exact opposite of wm8994_device_init() as well. Signed-off-by: Viresh Kumar Acked-by: Charles Keepax Signed-off-by: Lee Jones --- drivers/mfd/wm8994-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mfd/wm8994-core.c b/drivers/mfd/wm8994-core.c index 7eec619a6023..1e644aa53a2d 100644 --- a/drivers/mfd/wm8994-core.c +++ b/drivers/mfd/wm8994-core.c @@ -604,10 +604,10 @@ err: static void wm8994_device_exit(struct wm8994 *wm8994) { pm_runtime_disable(wm8994->dev); - mfd_remove_devices(wm8994->dev); wm8994_irq_exit(wm8994); regulator_bulk_disable(wm8994->num_supplies, wm8994->supplies); + mfd_remove_devices(wm8994->dev); } static const struct of_device_id wm8994_of_match[] = { -- cgit v1.2.3 From 1a41741fd60b0a2d1102c3d1ff9d58cb324a8d29 Mon Sep 17 00:00:00 2001 From: Viresh Kumar Date: Thu, 27 Oct 2016 15:50:18 +0530 Subject: mfd: wm8994-core: Don't use managed regulator bulk get API The kernel WARNs and then crashes today if wm8994_device_init() fails after calling devm_regulator_bulk_get(). That happens because there are multiple devices involved here and the order in which managed resources are freed isn't correct. The regulators are added as children of wm8994->dev. Whereas, devm_regulator_bulk_get() receives wm8994->dev as the device, though it gets the same regulators which were added as children of wm8994->dev earlier. During failures, the children are removed first and the core eventually calls regulator_unregister() for them. As regulator_put() was never done for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at WARN_ON(rdev->open_count); And eventually it crashes from debugfs_remove_recursive(). --------x------------------x---------------- wm8994 3-001a: Device is not a WM8994, ID is 0 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at /mnt/ssd/all/work/repos/devel/linux/drivers/regulator/core.c:4072 regulator_unregister+0xc8/0xd0 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc6-00154-g54fe84cbd50b #41 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [] (show_stack) from [] (dump_stack+0x88/0x9c) [] (dump_stack) from [] (__warn+0xe8/0x100) [] (__warn) from [] (warn_slowpath_null+0x20/0x28) [] (warn_slowpath_null) from [] (regulator_unregister+0xc8/0xd0) [] (regulator_unregister) from [] (release_nodes+0x16c/0x1dc) [] (release_nodes) from [] (__device_release_driver+0x8c/0x110) [] (__device_release_driver) from [] (device_release_driver+0x1c/0x28) [] (device_release_driver) from [] (bus_remove_device+0xd8/0x104) [] (bus_remove_device) from [] (device_del+0x10c/0x218) [] (device_del) from [] (platform_device_del+0x1c/0x88) [] (platform_device_del) from [] (platform_device_unregister+0xc/0x20) [] (platform_device_unregister) from [] (mfd_remove_devices_fn+0x5c/0x64) [] (mfd_remove_devices_fn) from [] (device_for_each_child_reverse+0x4c/0x78) [] (device_for_each_child_reverse) from [] (mfd_remove_devices+0x20/0x30) [] (mfd_remove_devices) from [] (wm8994_device_init+0x2ac/0x7f0) [] (wm8994_device_init) from [] (i2c_device_probe+0x178/0x1fc) [] (i2c_device_probe) from [] (driver_probe_device+0x214/0x2c0) [] (driver_probe_device) from [] (__driver_attach+0xac/0xb0) [] (__driver_attach) from [] (bus_for_each_dev+0x68/0x9c) [] (bus_for_each_dev) from [] (bus_add_driver+0x1a0/0x218) [] (bus_add_driver) from [] (driver_register+0x78/0xf8) [] (driver_register) from [] (i2c_register_driver+0x34/0x84) [] (i2c_register_driver) from [] (do_one_initcall+0x40/0x170) [] (do_one_initcall) from [] (kernel_init_freeable+0x15c/0x1fc) [] (kernel_init_freeable) from [] (kernel_init+0x8/0x114) [] (kernel_init) from [] (ret_from_fork+0x14/0x3c) ---[ end trace 0919d3d0bc998260 ]--- [snip..] Unable to handle kernel NULL pointer dereference at virtual address 00000078 pgd = c0004000 [00000078] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.8.0-rc6-00154-g54fe84cbd50b #41 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) task: ee874000 task.stack: ee878000 PC is at down_write+0x14/0x54 LR is at debugfs_remove_recursive+0x30/0x150 [snip..] [] (down_write) from [] (debugfs_remove_recursive+0x30/0x150) [] (debugfs_remove_recursive) from [] (_regulator_put+0x24/0xac) [] (_regulator_put) from [] (regulator_put+0x1c/0x2c) [] (regulator_put) from [] (release_nodes+0x16c/0x1dc) [] (release_nodes) from [] (driver_probe_device+0xec/0x2c0) [] (driver_probe_device) from [] (__driver_attach+0xac/0xb0) [] (__driver_attach) from [] (bus_for_each_dev+0x68/0x9c) [] (bus_for_each_dev) from [] (bus_add_driver+0x1a0/0x218) [] (bus_add_driver) from [] (driver_register+0x78/0xf8) [] (driver_register) from [] (i2c_register_driver+0x34/0x84) [] (i2c_register_driver) from [] (do_one_initcall+0x40/0x170) [] (do_one_initcall) from [] (kernel_init_freeable+0x15c/0x1fc) [] (kernel_init_freeable) from [] (kernel_init+0x8/0x114) [] (kernel_init) from [] (ret_from_fork+0x14/0x3c) Code: e1a04000 f590f000 e3a03001 e34f3fff (e1902f9f) ---[ end trace 0919d3d0bc998262 ]--- --------x------------------x---------------- Fix the kernel warnings and crashes by using regulator_bulk_get() instead of devm_regulator_bulk_get() and explicitly freeing the supplies in exit paths. Tested on Exynos 5250, dual core ARM A15 machine. Signed-off-by: Viresh Kumar Acked-by: Charles Keepax Signed-off-by: Lee Jones --- drivers/mfd/wm8994-core.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/mfd/wm8994-core.c b/drivers/mfd/wm8994-core.c index 1e644aa53a2d..8588dbad3301 100644 --- a/drivers/mfd/wm8994-core.c +++ b/drivers/mfd/wm8994-core.c @@ -393,8 +393,13 @@ static int wm8994_device_init(struct wm8994 *wm8994, int irq) BUG(); goto err; } - - ret = devm_regulator_bulk_get(wm8994->dev, wm8994->num_supplies, + + /* + * Can't use devres helper here as some of the supplies are provided by + * wm8994->dev's children (regulators) and those regulators are + * unregistered by the devres core before the supplies are freed. + */ + ret = regulator_bulk_get(wm8994->dev, wm8994->num_supplies, wm8994->supplies); if (ret != 0) { dev_err(wm8994->dev, "Failed to get supplies: %d\n", ret); @@ -405,7 +410,7 @@ static int wm8994_device_init(struct wm8994 *wm8994, int irq) wm8994->supplies); if (ret != 0) { dev_err(wm8994->dev, "Failed to enable supplies: %d\n", ret); - goto err; + goto err_regulator_free; } ret = wm8994_reg_read(wm8994, WM8994_SOFTWARE_RESET); @@ -596,6 +601,8 @@ err_irq: err_enable: regulator_bulk_disable(wm8994->num_supplies, wm8994->supplies); +err_regulator_free: + regulator_bulk_free(wm8994->num_supplies, wm8994->supplies); err: mfd_remove_devices(wm8994->dev); return ret; @@ -607,6 +614,7 @@ static void wm8994_device_exit(struct wm8994 *wm8994) wm8994_irq_exit(wm8994); regulator_bulk_disable(wm8994->num_supplies, wm8994->supplies); + regulator_bulk_free(wm8994->num_supplies, wm8994->supplies); mfd_remove_devices(wm8994->dev); } -- cgit v1.2.3 From f7db0ec9572f66b36c0d4d6bc4b564da53c8b35d Mon Sep 17 00:00:00 2001 From: Geliang Tang Date: Wed, 23 Nov 2016 22:24:35 +0800 Subject: dwc_eth_qos: drop duplicate headers Drop duplicate headers types.h and delay.h from dwc_eth_qos.c. Signed-off-by: Geliang Tang Signed-off-by: David S. Miller --- drivers/net/ethernet/synopsys/dwc_eth_qos.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/synopsys/dwc_eth_qos.c b/drivers/net/ethernet/synopsys/dwc_eth_qos.c index 5eedac495077..4ba2421e625d 100644 --- a/drivers/net/ethernet/synopsys/dwc_eth_qos.c +++ b/drivers/net/ethernet/synopsys/dwc_eth_qos.c @@ -33,7 +33,6 @@ #include #include -#include #include #include #include @@ -43,7 +42,6 @@ #include #include -#include #include #include -- cgit v1.2.3 From 89119f08354b628548118cacd686a7700372ad19 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Fri, 25 Nov 2016 17:22:27 +0200 Subject: Revert "i2c: designware: do not disable adapter after transfer" This reverts commit 0317e6c0f1dc1ba86b8d9dccc010c5e77b8355fa. Srinivas reported recently touchscreen and touchpad stopped working in Haswell based machine in Linux 4.9-rc series with timeout errors from i2c_designware: [ 16.508013] i2c_designware INT33C3:00: controller timed out [ 16.508302] i2c_hid i2c-MSFT0001:02: failed to change power setting. [ 17.532016] i2c_designware INT33C3:00: controller timed out [ 18.556022] i2c_designware INT33C3:00: controller timed out [ 18.556315] i2c_hid i2c-ATML1000:00: failed to retrieve report from device. I managed to reproduce similar errors on another Haswell based machine where touchscreen initialization fails maybe in every 1/5 - 1/2 boots. Since root cause for these errors is not clear yet and debugging is ongoing it's better to revert this commit as we are near to release. Reported-by: Srinivas Pandruvada Signed-off-by: Jarkko Nikula Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-core.c | 55 +++++++++++--------------------- 1 file changed, 18 insertions(+), 37 deletions(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index c53058d6139c..b403fa5ecf49 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -91,9 +91,7 @@ DW_IC_INTR_TX_ABRT | \ DW_IC_INTR_STOP_DET) -#define DW_IC_STATUS_ACTIVITY 0x1 -#define DW_IC_STATUS_TFE BIT(2) -#define DW_IC_STATUS_MST_ACTIVITY BIT(5) +#define DW_IC_STATUS_ACTIVITY 0x1 #define DW_IC_SDA_HOLD_RX_SHIFT 16 #define DW_IC_SDA_HOLD_RX_MASK GENMASK(23, DW_IC_SDA_HOLD_RX_SHIFT) @@ -478,25 +476,9 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) { struct i2c_msg *msgs = dev->msgs; u32 ic_tar = 0; - bool enabled; - enabled = dw_readl(dev, DW_IC_ENABLE_STATUS) & 1; - - if (enabled) { - u32 ic_status; - - /* - * Only disable adapter if ic_tar and ic_con can't be - * dynamically updated - */ - ic_status = dw_readl(dev, DW_IC_STATUS); - if (!dev->dynamic_tar_update_enabled || - (ic_status & DW_IC_STATUS_MST_ACTIVITY) || - !(ic_status & DW_IC_STATUS_TFE)) { - __i2c_dw_enable_and_wait(dev, false); - enabled = false; - } - } + /* Disable the adapter */ + __i2c_dw_enable_and_wait(dev, false); /* if the slave address is ten bit address, enable 10BITADDR */ if (dev->dynamic_tar_update_enabled) { @@ -526,8 +508,8 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) /* enforce disabled interrupts (due to HW issues) */ i2c_dw_disable_int(dev); - if (!enabled) - __i2c_dw_enable(dev, true); + /* Enable the adapter */ + __i2c_dw_enable(dev, true); /* Clear and enable interrupts */ dw_readl(dev, DW_IC_CLR_INTR); @@ -708,8 +690,7 @@ static int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev) } /* - * Prepare controller for a transaction and start transfer by calling - * i2c_dw_xfer_init() + * Prepare controller for a transaction and call i2c_dw_xfer_msg */ static int i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) @@ -752,6 +733,16 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) goto done; } + /* + * We must disable the adapter before returning and signaling the end + * of the current transfer. Otherwise the hardware might continue + * generating interrupts which in turn causes a race condition with + * the following transfer. Needs some more investigation if the + * additional interrupts are a hardware bug or this driver doesn't + * handle them correctly yet. + */ + __i2c_dw_enable(dev, false); + if (dev->msg_err) { ret = dev->msg_err; goto done; @@ -893,19 +884,9 @@ static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) */ tx_aborted: - if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) - || dev->msg_err) { - /* - * We must disable interruts before returning and signaling - * the end of the current transfer. Otherwise the hardware - * might continue generating interrupts for non-existent - * transfers. - */ - i2c_dw_disable_int(dev); - dw_readl(dev, DW_IC_CLR_INTR); - + if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err) complete(&dev->cmd_complete); - } else if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK)) { + else if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK)) { /* workaround to trigger pending interrupt */ stat = dw_readl(dev, DW_IC_INTR_MASK); i2c_dw_disable_int(dev); -- cgit v1.2.3 From 97db8afa2ab919fc400fe982f5054060868bdf07 Mon Sep 17 00:00:00 2001 From: Andrew Lunn Date: Thu, 24 Nov 2016 00:08:13 +0100 Subject: net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it actually does not. The hardware probably does support it, but there is no code to configure the filter. As a quick and simple fix, remove the flag. This will cause the core to fall back to promiscuous mode. Signed-off-by: Andrew Lunn Fixes: b50b72de2f2f ("net: mvneta: enable features before registering the driver") Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/mvneta.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c index 5cb07c2017bf..0c0a45af950f 100644 --- a/drivers/net/ethernet/marvell/mvneta.c +++ b/drivers/net/ethernet/marvell/mvneta.c @@ -4151,7 +4151,7 @@ static int mvneta_probe(struct platform_device *pdev) dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO; dev->hw_features |= dev->features; dev->vlan_features |= dev->features; - dev->priv_flags |= IFF_UNICAST_FLT | IFF_LIVE_ADDR_CHANGE; + dev->priv_flags |= IFF_LIVE_ADDR_CHANGE; dev->gso_max_segs = MVNETA_MAX_TSO_SEGS; err = register_netdev(dev); -- cgit v1.2.3 From 1f1e70efe53c01844ce76d77c3383c2bcb6beb49 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 24 Nov 2016 14:20:43 +0300 Subject: fsl/fman: fix a leak in tgec_free() We set "tgec->cfg" to NULL before passing it to kfree(). There is no need to set it to NULL at all. Let's just delete it. Fixes: 57ba4c9b56d8 ("fsl/fman: Add FMan MAC support") Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fman/fman_tgec.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/freescale/fman/fman_tgec.c b/drivers/net/ethernet/freescale/fman/fman_tgec.c index efabb04a1ae8..4b0f3a50b293 100644 --- a/drivers/net/ethernet/freescale/fman/fman_tgec.c +++ b/drivers/net/ethernet/freescale/fman/fman_tgec.c @@ -722,9 +722,6 @@ int tgec_free(struct fman_mac *tgec) { free_init_resources(tgec); - if (tgec->cfg) - tgec->cfg = NULL; - kfree(tgec->cfg); kfree(tgec); -- cgit v1.2.3 From 4ee12efa2dbf949d72ef2f7ef2e044af5a67b515 Mon Sep 17 00:00:00 2001 From: Geliang Tang Date: Thu, 24 Nov 2016 21:58:29 +0800 Subject: ibmvnic: drop duplicate header seq_file.h Drop duplicate header seq_file.h from ibmvnic.c. Signed-off-by: Geliang Tang Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/ibmvnic.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/ibm/ibmvnic.c b/drivers/net/ethernet/ibm/ibmvnic.c index 4f3281a03e7e..0fbf686f5e7c 100644 --- a/drivers/net/ethernet/ibm/ibmvnic.c +++ b/drivers/net/ethernet/ibm/ibmvnic.c @@ -74,7 +74,6 @@ #include #include #include -#include #include #include "ibmvnic.h" -- cgit v1.2.3 From 8f8a8b13b447842b147539ae2cab6699897539b9 Mon Sep 17 00:00:00 2001 From: Geliang Tang Date: Thu, 24 Nov 2016 21:58:32 +0800 Subject: net: ieee802154: drop duplicate header delay.h Drop duplicate header delay.h from adf7242.c. Signed-off-by: Geliang Tang Acked-by: Stefan Schmidt Signed-off-by: David S. Miller --- drivers/net/ieee802154/adf7242.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ieee802154/adf7242.c b/drivers/net/ieee802154/adf7242.c index 9fa7ac9f8e68..f355df7cf84a 100644 --- a/drivers/net/ieee802154/adf7242.c +++ b/drivers/net/ieee802154/adf7242.c @@ -20,7 +20,6 @@ #include #include #include -#include #include #include #include -- cgit v1.2.3 From 5e7dfeb758663391ec721e6a4519d3df874f9b1f Mon Sep 17 00:00:00 2001 From: Geliang Tang Date: Thu, 24 Nov 2016 21:58:33 +0800 Subject: net/mlx5: drop duplicate header delay.h Drop duplicate header delay.h from mlx5/core/main.c. Signed-off-by: Geliang Tang Acked-by: Matan Barak Acked-by: Saeed Mahameed Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx5/core/main.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx5/core/main.c b/drivers/net/ethernet/mellanox/mlx5/core/main.c index 3eb931585b3e..3b7c6a9f2b5f 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/main.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c @@ -46,7 +46,6 @@ #include #include #include -#include #include #ifdef CONFIG_RFS_ACCEL #include -- cgit v1.2.3 From e8f967c3d88489fc1562a31d4e44d905ac1d3aff Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Thu, 24 Nov 2016 17:28:12 +0100 Subject: mvpp2: use correct size for memset gcc-7 detects a short memset in mvpp2, introduced in the original merge of the driver: drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init': drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size] The result seems to be that we write uninitialized data into the flow table registers, although we did not get any warning about that uninitialized data usage. Using sizeof() lets us initialize then entire array instead. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Arnd Bergmann Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/mvpp2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c index 60227a3452a4..1026c452e39d 100644 --- a/drivers/net/ethernet/marvell/mvpp2.c +++ b/drivers/net/ethernet/marvell/mvpp2.c @@ -3293,7 +3293,7 @@ static void mvpp2_cls_init(struct mvpp2 *priv) mvpp2_write(priv, MVPP2_CLS_MODE_REG, MVPP2_CLS_MODE_ACTIVE_MASK); /* Clear classifier flow table */ - memset(&fe.data, 0, MVPP2_CLS_FLOWS_TBL_DATA_WORDS); + memset(&fe.data, 0, sizeof(fe.data)); for (index = 0; index < MVPP2_CLS_FLOWS_TBL_SIZE; index++) { fe.index = index; mvpp2_cls_flow_write(priv, &fe); -- cgit v1.2.3