From 53dd3f802a6e269868cb599609287a841e65a996 Mon Sep 17 00:00:00 2001 From: Eric Biggers Date: Fri, 26 Aug 2022 23:58:46 -0700 Subject: fscrypt: change fscrypt_dio_supported() to prepare for STATX_DIOALIGN To prepare for STATX_DIOALIGN support, make two changes to fscrypt_dio_supported(). First, remove the filesystem-block-alignment check and make the filesystems handle it instead. It previously made sense to have it in fs/crypto/; however, to support STATX_DIOALIGN the alignment restriction would have to be returned to filesystems. It ends up being simpler if filesystems handle this part themselves, especially for f2fs which only allows fs-block-aligned DIO in the first place. Second, make fscrypt_dio_supported() work on inodes whose encryption key hasn't been set up yet, by making it set up the key if needed. This is required for statx(), since statx() doesn't require a file descriptor. Reviewed-by: Christoph Hellwig Signed-off-by: Eric Biggers Link: https://lore.kernel.org/r/20220827065851.135710-4-ebiggers@kernel.org --- fs/crypto/inline_crypt.c | 49 ++++++++++++++++++++++++------------------------ 1 file changed, 24 insertions(+), 25 deletions(-) (limited to 'fs/crypto') diff --git a/fs/crypto/inline_crypt.c b/fs/crypto/inline_crypt.c index 90f3e68f166e..8d4bee5bccbf 100644 --- a/fs/crypto/inline_crypt.c +++ b/fs/crypto/inline_crypt.c @@ -401,46 +401,45 @@ bool fscrypt_mergeable_bio_bh(struct bio *bio, EXPORT_SYMBOL_GPL(fscrypt_mergeable_bio_bh); /** - * fscrypt_dio_supported() - check whether a DIO (direct I/O) request is - * supported as far as encryption is concerned - * @iocb: the file and position the I/O is targeting - * @iter: the I/O data segment(s) + * fscrypt_dio_supported() - check whether DIO (direct I/O) is supported on an + * inode, as far as encryption is concerned + * @inode: the inode in question * * Return: %true if there are no encryption constraints that prevent DIO from * being supported; %false if DIO is unsupported. (Note that in the * %true case, the filesystem might have other, non-encryption-related - * constraints that prevent DIO from actually being supported.) + * constraints that prevent DIO from actually being supported. Also, on + * encrypted files the filesystem is still responsible for only allowing + * DIO when requests are filesystem-block-aligned.) */ -bool fscrypt_dio_supported(struct kiocb *iocb, struct iov_iter *iter) +bool fscrypt_dio_supported(struct inode *inode) { - const struct inode *inode = file_inode(iocb->ki_filp); - const unsigned int blocksize = i_blocksize(inode); + int err; /* If the file is unencrypted, no veto from us. */ if (!fscrypt_needs_contents_encryption(inode)) return true; - /* We only support DIO with inline crypto, not fs-layer crypto. */ - if (!fscrypt_inode_uses_inline_crypto(inode)) - return false; - /* - * Since the granularity of encryption is filesystem blocks, the file - * position and total I/O length must be aligned to the filesystem block - * size -- not just to the block device's logical block size as is - * traditionally the case for DIO on many filesystems. + * We only support DIO with inline crypto, not fs-layer crypto. * - * We require that the user-provided memory buffers be filesystem block - * aligned too. It is simpler to have a single alignment value required - * for all properties of the I/O, as is normally the case for DIO. - * Also, allowing less aligned buffers would imply that data units could - * cross bvecs, which would greatly complicate the I/O stack, which - * assumes that bios can be split at any bvec boundary. + * To determine whether the inode is using inline crypto, we have to set + * up the key if it wasn't already done. This is because in the current + * design of fscrypt, the decision of whether to use inline crypto or + * not isn't made until the inode's encryption key is being set up. In + * the DIO read/write case, the key will always be set up already, since + * the file will be open. But in the case of statx(), the key might not + * be set up yet, as the file might not have been opened yet. */ - if (!IS_ALIGNED(iocb->ki_pos | iov_iter_alignment(iter), blocksize)) + err = fscrypt_require_key(inode); + if (err) { + /* + * Key unavailable or couldn't be set up. This edge case isn't + * worth worrying about; just report that DIO is unsupported. + */ return false; - - return true; + } + return fscrypt_inode_uses_inline_crypto(inode); } EXPORT_SYMBOL_GPL(fscrypt_dio_supported); -- cgit v1.2.3