1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/regulator/rohm,bd71847-regulator.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: ROHM BD71847 and BD71850 Power Management Integrated Circuit regulators
maintainers:
- Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
description: |
List of regulators provided by this controller. BD71847 regulators node
should be sub node of the BD71847 MFD node. See BD71847 MFD bindings at
Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
Regulator nodes should be named to BUCK_<number> and LDO_<number>. The
definition for each of these nodes is defined using the standard
binding for regulators at
Documentation/devicetree/bindings/regulator/regulator.txt.
Note that if BD71847 starts at RUN state you probably want to use
regulator-boot-on at least for BUCK5. LDO6 is supplied by it and it must
not be disabled by driver at startup. If BUCK5 is disabled at startup the
voltage monitoring for LDO5/LDO6 can cause PMIC to reset.
#The valid names for BD71847 regulator nodes are:
#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6
#LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
patternProperties:
"^LDO[1-6]$":
type: object
allOf:
- $ref: regulator.yaml#
description:
Properties for single LDO regulator.
properties:
regulator-name:
pattern: "^ldo[1-6]$"
description:
should be "ldo1", ..., "ldo6"
"^BUCK[1-6]$":
type: object
allOf:
- $ref: regulator.yaml#
description:
Properties for single BUCK regulator.
properties:
regulator-name:
pattern: "^buck[1-6]$"
description:
should be "buck1", ..., "buck6"
rohm,dvs-run-voltage:
allOf:
- $ref: "/schemas/types.yaml#/definitions/uint32"
- minimum: 0
maximum: 1300000
description:
PMIC default "RUN" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-idle-voltage:
allOf:
- $ref: "/schemas/types.yaml#/definitions/uint32"
- minimum: 0
maximum: 1300000
description:
PMIC default "IDLE" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-suspend-voltage:
allOf:
- $ref: "/schemas/types.yaml#/definitions/uint32"
- minimum: 0
maximum: 1300000
description:
PMIC default "SUSPEND" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
# Supported default DVS states:
#
# BD71847:
# buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage
# ----------------------------------------------------------------
# 1 | supported | supported | supported
# ----------------------------------------------------------------
# 2 | supported | supported | not supported
# ----------------------------------------------------------------
# rest | not supported | not supported | not supported
required:
- regulator-name
additionalProperties: false
additionalProperties: false
|
