1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
|
#ifndef _RAID1_H
#define _RAID1_H
struct raid1_info {
struct md_rdev *rdev;
sector_t head_position;
};
/*
* memory pools need a pointer to the mddev, so they can force an unplug
* when memory is tight, and a count of the number of drives that the
* pool was allocated for, so they know how much to allocate and free.
* mddev->raid_disks cannot be used, as it can change while a pool is active
* These two datums are stored in a kmalloced struct.
* The 'raid_disks' here is twice the raid_disks in r1conf.
* This allows space for each 'real' device can have a replacement in the
* second half of the array.
*/
struct pool_info {
struct mddev *mddev;
int raid_disks;
};
struct r1conf {
struct mddev *mddev;
struct raid1_info *mirrors; /* twice 'raid_disks' to
* allow for replacements.
*/
int raid_disks;
/* When choose the best device for a read (read_balance())
* we try to keep sequential reads one the same device
* using 'last_used' and 'next_seq_sect'
*/
int last_used;
sector_t next_seq_sect;
/* During resync, read_balancing is only allowed on the part
* of the array that has been resynced. 'next_resync' tells us
* where that is.
*/
sector_t next_resync;
spinlock_t device_lock;
/* list of 'struct r1bio' that need to be processed by raid1d,
* whether to retry a read, writeout a resync or recovery
* block, or anything else.
*/
struct list_head retry_list;
/* queue pending writes to be submitted on unplug */
struct bio_list pending_bio_list;
int pending_count;
/* for use when syncing mirrors:
* We don't allow both normal IO and resync/recovery IO at
* the same time - resync/recovery can only happen when there
* is no other IO. So when either is active, the other has to wait.
* See more details description in raid1.c near raise_barrier().
*/
wait_queue_head_t wait_barrier;
spinlock_t resync_lock;
int nr_pending;
int nr_waiting;
int nr_queued;
int barrier;
/* Set to 1 if a full sync is needed, (fresh device added).
* Cleared when a sync completes.
*/
int fullsync;
/* When the same as mddev->recovery_disabled we don't allow
* recovery to be attempted as we expect a read error.
*/
int recovery_disabled;
/* poolinfo contains information about the content of the
* mempools - it changes when the array grows or shrinks
*/
struct pool_info *poolinfo;
mempool_t *r1bio_pool;
mempool_t *r1buf_pool;
/* temporary buffer to synchronous IO when attempting to repair
* a read error.
*/
struct page *tmppage;
/* When taking over an array from a different personality, we store
* the new thread here until we fully activate the array.
*/
struct md_thread *thread;
};
/*
* this is our 'private' RAID1 bio.
*
* it contains information about what kind of IO operations were started
* for this RAID1 operation, and about their status:
*/
struct r1bio {
atomic_t remaining; /* 'have we finished' count,
* used from IRQ handlers
*/
atomic_t behind_remaining; /* number of write-behind ios remaining
* in this BehindIO request
*/
sector_t sector;
int sectors;
unsigned long state;
struct mddev *mddev;
/*
* original bio going to /dev/mdx
*/
struct bio *master_bio;
/*
* if the IO is in READ direction, then this is where we read
*/
int read_disk;
struct list_head retry_list;
/* Next two are only valid when R1BIO_BehindIO is set */
struct bio_vec *behind_bvecs;
int behind_page_count;
/*
* if the IO is in WRITE direction, then multiple bios are used.
* We choose the number when they are allocated.
*/
struct bio *bios[0];
/* DO NOT PUT ANY NEW FIELDS HERE - bios array is contiguously alloced*/
};
/* when we get a read error on a read-only array, we redirect to another
* device without failing the first device, or trying to over-write to
* correct the read error. To keep track of bad blocks on a per-bio
* level, we store IO_BLOCKED in the appropriate 'bios' pointer
*/
#define IO_BLOCKED ((struct bio *)1)
/* When we successfully write to a known bad-block, we need to remove the
* bad-block marking which must be done from process context. So we record
* the success by setting bios[n] to IO_MADE_GOOD
*/
#define IO_MADE_GOOD ((struct bio *)2)
#define BIO_SPECIAL(bio) ((unsigned long)bio <= 2)
/* bits for r1bio.state */
#define R1BIO_Uptodate 0
#define R1BIO_IsSync 1
#define R1BIO_Degraded 2
#define R1BIO_BehindIO 3
/* Set ReadError on bios that experience a readerror so that
* raid1d knows what to do with them.
*/
#define R1BIO_ReadError 4
/* For write-behind requests, we call bi_end_io when
* the last non-write-behind device completes, providing
* any write was successful. Otherwise we call when
* any write-behind write succeeds, otherwise we call
* with failure when last write completes (and all failed).
* Record that bi_end_io was called with this flag...
*/
#define R1BIO_Returned 6
/* If a write for this request means we can clear some
* known-bad-block records, we set this flag
*/
#define R1BIO_MadeGood 7
#define R1BIO_WriteError 8
extern int md_raid1_congested(struct mddev *mddev, int bits);
#endif
|