summaryrefslogtreecommitdiffstats
path: root/include/linux/mmc/sdio.h
blob: 245cdacee5443791eb5418d10bde3daa190351a9 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
/*
 *  include/linux/mmc/sdio.h
 *
 *  Copyright 2006-2007 Pierre Ossman
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or (at
 * your option) any later version.
 */

#ifndef MMC_SDIO_H
#define MMC_SDIO_H

/* SDIO commands                         type  argument     response */
#define SD_IO_SEND_OP_COND          5 /* bcr  [23:0] OCR         R4  */
#define SD_IO_RW_DIRECT            52 /* ac   [31:0] See below   R5  */
#define SD_IO_RW_EXTENDED          53 /* adtc [31:0] See below   R5  */

/*
 * SD_IO_RW_DIRECT argument format:
 *
 *      [31] R/W flag
 *      [30:28] Function number
 *      [27] RAW flag
 *      [25:9] Register address
 *      [7:0] Data
 */

/*
 * SD_IO_RW_EXTENDED argument format:
 *
 *      [31] R/W flag
 *      [30:28] Function number
 *      [27] Block mode
 *      [26] Increment address
 *      [25:9] Register address
 *      [8:0] Byte/block count
 */

#define R4_MEMORY_PRESENT (1 << 27)

/*
  SDIO status in R5
  Type
	e : error bit
	s : status bit
	r : detected and set for the actual command response
	x : detected and set during command execution. the host must poll
            the card by sending status command in order to read these bits.
  Clear condition
	a : according to the card state
	b : always related to the previous command. Reception of
            a valid command will clear it (with a delay of one command)
	c : clear by read
 */

#define R5_COM_CRC_ERROR	(1 << 15)	/* er, b */
#define R5_ILLEGAL_COMMAND	(1 << 14)	/* er, b */
#define R5_ERROR		(1 << 11)	/* erx, c */
#define R5_FUNCTION_NUMBER	(1 << 9)	/* er, c */
#define R5_OUT_OF_RANGE		(1 << 8)	/* er, c */
#define R5_STATUS(x)		(x & 0xCB00)
#define R5_IO_CURRENT_STATE(x)	((x & 0x3000) >> 12) /* s, b */

/*
 * Card Common Control Registers (CCCR)
 */

#define SDIO_CCCR_CCCR		0x00

#define  SDIO_CCCR_REV_1_00	0	/* CCCR/FBR Version 1.00 */
#define  SDIO_CCCR_REV_1_10	1	/* CCCR/FBR Version 1.10 */
#define  SDIO_CCCR_REV_1_20	2	/* CCCR/FBR Version 1.20 */

#define  SDIO_SDIO_REV_1_00	0	/* SDIO Spec Version 1.00 */
#define  SDIO_SDIO_REV_1_10	1	/* SDIO Spec Version 1.10 */
#define  SDIO_SDIO_REV_1_20	2	/* SDIO Spec Version 1.20 */
#define  SDIO_SDIO_REV_2_00	3	/* SDIO Spec Version 2.00 */

#define SDIO_CCCR_SD		0x01

#define  SDIO_SD_REV_1_01	0	/* SD Physical Spec Version 1.01 */
#define  SDIO_SD_REV_1_10	1	/* SD Physical Spec Version 1.10 */
#define  SDIO_SD_REV_2_00	2	/* SD Physical Spec Version 2.00 */

#define SDIO_CCCR_IOEx		0x02
#define SDIO_CCCR_IORx		0x03

#define SDIO_CCCR_IENx		0x04	/* Function/Master Interrupt Enable */
#define SDIO_CCCR_INTx		0x05	/* Function Interrupt Pending */

#define SDIO_CCCR_ABORT		0x06	/* function abort/card reset */

#define SDIO_CCCR_IF		0x07	/* bus interface controls */

#define  SDIO_BUS_WIDTH_1BIT	0x00
#define  SDIO_BUS_WIDTH_4BIT	0x02
#define  SDIO_BUS_ECSI		0x20	/* Enable continuous SPI interrupt */
#define  SDIO_BUS_SCSI		0x40	/* Support continuous SPI interrupt */

#define  SDIO_BUS_ASYNC_INT	0x20

#define  SDIO_BUS_CD_DISABLE     0x80	/* disable pull-up on DAT3 (pin 1) */

#define SDIO_CCCR_CAPS		0x08

#define  SDIO_CCCR_CAP_SDC	0x01	/* can do CMD52 while data transfer */
#define  SDIO_CCCR_CAP_SMB	0x02	/* can do multi-block xfers (CMD53) */
#define  SDIO_CCCR_CAP_SRW	0x04	/* supports read-wait protocol */
#define  SDIO_CCCR_CAP_SBS	0x08	/* supports suspend/resume */
#define  SDIO_CCCR_CAP_S4MI	0x10	/* interrupt during 4-bit CMD53 */
#define  SDIO_CCCR_CAP_E4MI	0x20	/* enable ints during 4-bit CMD53 */
#define  SDIO_CCCR_CAP_LSC	0x40	/* low speed card */
#define  SDIO_CCCR_CAP_4BLS	0x80	/* 4 bit low speed card */

#define SDIO_CCCR_CIS		0x09	/* common CIS pointer (3 bytes) */

/* Following 4 regs are valid only if SBS is set */
#define SDIO_CCCR_SUSPEND	0x0c
#define SDIO_CCCR_SELx		0x0d
#define SDIO_CCCR_EXECx		0x0e
#define SDIO_CCCR_READYx	0x0f

#define SDIO_CCCR_BLKSIZE	0x10

#define SDIO_CCCR_POWER		0x12

#define  SDIO_POWER_SMPC	0x01	/* Supports Master Power Control */
#define  SDIO_POWER_EMPC	0x02	/* Enable Master Power Control */

#define SDIO_CCCR_SPEED		0x13

#define  SDIO_SPEED_SHS		0x01	/* Supports High-Speed mode */
#define  SDIO_SPEED_EHS		0x02	/* Enable High-Speed mode */

/*
 * Function Basic Registers (FBR)
 */

#define SDIO_FBR_BASE(f)	((f) * 0x100) /* base of function f's FBRs */

#define SDIO_FBR_STD_IF		0x00

#define  SDIO_FBR_SUPPORTS_CSA	0x40	/* supports Code Storage Area */
#define  SDIO_FBR_ENABLE_CSA	0x80	/* enable Code Storage Area */

#define SDIO_FBR_STD_IF_EXT	0x01

#define SDIO_FBR_POWER		0x02

#define  SDIO_FBR_POWER_SPS	0x01	/* Supports Power Selection */
#define  SDIO_FBR_POWER_EPS	0x02	/* Enable (low) Power Selection */

#define SDIO_FBR_CIS		0x09	/* CIS pointer (3 bytes) */


#define SDIO_FBR_CSA		0x0C	/* CSA pointer (3 bytes) */

#define SDIO_FBR_CSA_DATA	0x0F

#define SDIO_FBR_BLKSIZE	0x10	/* block size (2 bytes) */

#endif