summaryrefslogtreecommitdiffstats
path: root/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch')
-rw-r--r--target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch729
1 files changed, 0 insertions, 729 deletions
diff --git a/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch b/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch
deleted file mode 100644
index c66eb6d887..0000000000
--- a/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch
+++ /dev/null
@@ -1,729 +0,0 @@
-From 0feb25cf50f89502ea7f2150f0fab1f9d40b138a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil@raspberrypi.org>
-Date: Mon, 8 Feb 2016 09:46:33 +0000
-Subject: [PATCH] BCM270X_DT: Adjust overlay README formatting
-
----
- arch/arm/boot/dts/overlays/README | 414 +++++++++++++++++++-------------------
- 1 file changed, 207 insertions(+), 207 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -83,58 +83,58 @@ Name: <The base DTB>
- Info: Configures the base Raspberry Pi hardware
- Load: <loaded automatically>
- Params:
-- audio Set to "on" to enable the onboard ALSA audio
-- interface (default "off")
-+ audio Set to "on" to enable the onboard ALSA audio
-+ interface (default "off")
-
-- i2c_arm Set to "on" to enable the ARM's i2c interface
-- (default "off")
-+ i2c_arm Set to "on" to enable the ARM's i2c interface
-+ (default "off")
-
-- i2c_vc Set to "on" to enable the i2c interface
-- usually reserved for the VideoCore processor
-- (default "off")
-+ i2c_vc Set to "on" to enable the i2c interface
-+ usually reserved for the VideoCore processor
-+ (default "off")
-
-- i2c An alias for i2c_arm
-+ i2c An alias for i2c_arm
-
-- i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
-- (default "100000")
-+ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
-+ (default "100000")
-
-- i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
-- (default "100000")
-+ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
-+ (default "100000")
-
-- i2c_baudrate An alias for i2c_arm_baudrate
-+ i2c_baudrate An alias for i2c_arm_baudrate
-
-- i2s Set to "on" to enable the i2s interface
-- (default "off")
-+ i2s Set to "on" to enable the i2s interface
-+ (default "off")
-
-- spi Set to "on" to enable the spi interfaces
-- (default "off")
-+ spi Set to "on" to enable the spi interfaces
-+ (default "off")
-
-- random Set to "on" to enable the hardware random
-- number generator (default "on")
-+ random Set to "on" to enable the hardware random
-+ number generator (default "on")
-
-- uart0 Set to "off" to disable uart0 (default "on")
-+ uart0 Set to "off" to disable uart0 (default "on")
-
-- watchdog Set to "on" to enable the hardware watchdog
-- (default "off")
-+ watchdog Set to "on" to enable the hardware watchdog
-+ (default "off")
-
-- act_led_trigger Choose which activity the LED tracks.
-- Use "heartbeat" for a nice load indicator.
-- (default "mmc")
-+ act_led_trigger Choose which activity the LED tracks.
-+ Use "heartbeat" for a nice load indicator.
-+ (default "mmc")
-
-- act_led_activelow Set to "on" to invert the sense of the LED
-- (default "off")
-+ act_led_activelow Set to "on" to invert the sense of the LED
-+ (default "off")
-
-- act_led_gpio Set which GPIO to use for the activity LED
-- (in case you want to connect it to an external
-- device)
-- (default "16" on a non-Plus board, "47" on a
-- Plus or Pi 2)
-+ act_led_gpio Set which GPIO to use for the activity LED
-+ (in case you want to connect it to an external
-+ device)
-+ (default "16" on a non-Plus board, "47" on a
-+ Plus or Pi 2)
-
- pwr_led_trigger
- pwr_led_activelow
- pwr_led_gpio
-- As for act_led_*, but using the PWR LED.
-- Not available on Model A/B boards.
-+ As for act_led_*, but using the PWR LED.
-+ Not available on Model A/B boards.
-
- N.B. It is recommended to only enable those interfaces that are needed.
- Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
-@@ -149,19 +149,19 @@ Params:
- Name: ads7846
- Info: ADS7846 Touch controller
- Load: dtoverlay=ads7846,<param>=<val>
--Params: cs SPI bus Chip Select (default 1)
-- speed SPI bus speed (default 2MHz, max 3.25MHz)
-- penirq GPIO used for PENIRQ. REQUIRED
-- penirq_pull Set GPIO pull (default 0=none, 2=pullup)
-- swapxy Swap x and y axis
-- xmin Minimum value on the X axis (default 0)
-- ymin Minimum value on the Y axis (default 0)
-- xmax Maximum value on the X axis (default 4095)
-- ymax Maximum value on the Y axis (default 4095)
-- pmin Minimum reported pressure value (default 0)
-- pmax Maximum reported pressure value (default 65535)
-- xohms Touchpanel sensitivity (X-plate resistance)
-- (default 400)
-+Params: cs SPI bus Chip Select (default 1)
-+ speed SPI bus speed (default 2MHz, max 3.25MHz)
-+ penirq GPIO used for PENIRQ. REQUIRED
-+ penirq_pull Set GPIO pull (default 0=none, 2=pullup)
-+ swapxy Swap x and y axis
-+ xmin Minimum value on the X axis (default 0)
-+ ymin Minimum value on the Y axis (default 0)
-+ xmax Maximum value on the X axis (default 4095)
-+ ymax Maximum value on the Y axis (default 4095)
-+ pmin Minimum reported pressure value (default 0)
-+ pmax Maximum reported pressure value (default 65535)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+ (default 400)
-
- penirq is required and usually xohms (60-100) has to be set as well.
- Apart from that, pmax (255) and swapxy are also common.
-@@ -175,12 +175,12 @@ Name: at86rf233
- Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
- connected to spi0.0
- Load: dtoverlay=at86rf233,<param>=<val>
--Params: interrupt GPIO used for INT (default 23)
-- reset GPIO used for Reset (default 24)
-- sleep GPIO used for Sleep (default 25)
-- speed SPI bus speed in Hz (default 6000000)
-- trim Fine tuning of the internal capacitance
-- arrays (0=+0pF, 15=+4.5pF, default 15)
-+Params: interrupt GPIO used for INT (default 23)
-+ reset GPIO used for Reset (default 24)
-+ sleep GPIO used for Sleep (default 25)
-+ speed SPI bus speed in Hz (default 6000000)
-+ trim Fine tuning of the internal capacitance
-+ arrays (0=+0pF, 15=+4.5pF, default 15)
-
-
- Name: bmp085_i2c-sensor
-@@ -194,8 +194,8 @@ Name: dht11
- Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
- Also sometimes found with the part number(s) AM230x.
- Load: dtoverlay=dht11,<param>=<val>
--Params: gpiopin GPIO connected to the sensor's DATA output.
-- (default 4)
-+Params: gpiopin GPIO connected to the sensor's DATA output.
-+ (default 4)
-
-
- Name: dwc-otg
-@@ -208,15 +208,15 @@ Params: <None>
- Name: dwc2
- Info: Selects the dwc2 USB controller driver
- Load: dtoverlay=dwc2,<param>=<val>
--Params: dr_mode Dual role mode: "host", "peripheral" or "otg"
-+Params: dr_mode Dual role mode: "host", "peripheral" or "otg"
-
-- g-rx-fifo-size Size of rx fifo size in gadget mode
-+ g-rx-fifo-size Size of rx fifo size in gadget mode
-
-- g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget
-- mode
-+ g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget
-+ mode
-
-- g-tx-fifo-size Size of periodic tx fifo per endpoint
-- (except ep0) in gadget mode
-+ g-tx-fifo-size Size of periodic tx fifo per endpoint
-+ (except ep0) in gadget mode
-
-
- [ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
-@@ -225,9 +225,9 @@ Params: dr_mode Dual ro
- Name: enc28j60
- Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
- Load: dtoverlay=enc28j60,<param>=<val>
--Params: int_pin GPIO used for INT (default 25)
-+Params: int_pin GPIO used for INT (default 25)
-
-- speed SPI bus speed (default 12000000)
-+ speed SPI bus speed (default 12000000)
-
-
- Name: gpio-ir
-@@ -237,26 +237,26 @@ Info: Use GPIO pin as rc-core style in
- not required! The key mapping and other decoding parameters can be
- configured by "ir-keytable" tool.
- Load: dtoverlay=gpio-ir,<param>=<val>
--Params: gpio_pin Input pin number. Default is 18.
-+Params: gpio_pin Input pin number. Default is 18.
-
-- gpio_pull Desired pull-up/down state (off, down, up)
-- Default is "down".
-+ gpio_pull Desired pull-up/down state (off, down, up)
-+ Default is "down".
-
-- rc-map-name Default rc keymap (can also be changed by
-- ir-keytable), defaults to "rc-rc6-mce"
-+ rc-map-name Default rc keymap (can also be changed by
-+ ir-keytable), defaults to "rc-rc6-mce"
-
-
- Name: gpio-poweroff
- Info: Drives a GPIO high or low on reboot
- Load: dtoverlay=gpio-poweroff,<param>=<val>
--Params: gpiopin GPIO for signalling (default 26)
-+Params: gpiopin GPIO for signalling (default 26)
-
-- active_low Set if the power control device requires a
-- high->low transition to trigger a power-down.
-- Note that this will require the support of a
-- custom dt-blob.bin to prevent a power-down
-- during the boot process, and that a reboot
-- will also cause the pin to go low.
-+ active_low Set if the power control device requires a
-+ high->low transition to trigger a power-down.
-+ Note that this will require the support of a
-+ custom dt-blob.bin to prevent a power-down
-+ during the boot process, and that a reboot
-+ will also cause the pin to go low.
-
-
- Name: hifiberry-amp
-@@ -300,65 +300,65 @@ Name: hy28a
- Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
- Default values match Texy's display shield
- Load: dtoverlay=hy28a,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-- resetgpio GPIO used to reset controller
-+ resetgpio GPIO used to reset controller
-
-- ledgpio GPIO used to control backlight
-+ ledgpio GPIO used to control backlight
-
-
- Name: hy28b
- Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics
- Default values match Texy's display shield
- Load: dtoverlay=hy28b,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-- resetgpio GPIO used to reset controller
-+ resetgpio GPIO used to reset controller
-
-- ledgpio GPIO used to control backlight
-+ ledgpio GPIO used to control backlight
-
-
- Name: i2c-gpio
- Info: Adds support for software i2c controller on gpio pins
- Load: dtoverlay=i2c-gpio,<param>=<val>
--Params: i2c_gpio_sda GPIO used for I2C data (default "23")
-+Params: i2c_gpio_sda GPIO used for I2C data (default "23")
-
-- i2c_gpio_scl GPIO used for I2C clock (default "24")
-+ i2c_gpio_scl GPIO used for I2C clock (default "24")
-
-- i2c_gpio_delay_us Clock delay in microseconds
-- (default "2" = ~100kHz)
-+ i2c_gpio_delay_us Clock delay in microseconds
-+ (default "2" = ~100kHz)
-
-
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
- Load: dtoverlay=i2c-rtc,<param>=<val>
--Params: ds1307 Select the DS1307 device
-+Params: ds1307 Select the DS1307 device
-
-- ds3231 Select the DS3231 device
-+ ds3231 Select the DS3231 device
-
-- mcp7941x Select the MCP7941x device
-+ mcp7941x Select the MCP7941x device
-
-- pcf2127 Select the PCF2127 device
-+ pcf2127 Select the PCF2127 device
-
-- pcf8523 Select the PCF8523 device
-+ pcf8523 Select the PCF8523 device
-
-- pcf8563 Select the PCF8563 device
-+ pcf8563 Select the PCF8563 device
-
-
- Name: i2s-mmap
-@@ -396,70 +396,70 @@ Name: lirc-rpi
- Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
- Consult the module documentation for more details.
- Load: dtoverlay=lirc-rpi,<param>=<val>
--Params: gpio_out_pin GPIO for output (default "17")
-+Params: gpio_out_pin GPIO for output (default "17")
-
-- gpio_in_pin GPIO for input (default "18")
-+ gpio_in_pin GPIO for input (default "18")
-
-- gpio_in_pull Pull up/down/off on the input pin
-- (default "down")
-+ gpio_in_pull Pull up/down/off on the input pin
-+ (default "down")
-
-- sense Override the IR receive auto-detection logic:
-- "0" = force active-high
-- "1" = force active-low
-- "-1" = use auto-detection
-- (default "-1")
-+ sense Override the IR receive auto-detection logic:
-+ "0" = force active-high
-+ "1" = force active-low
-+ "-1" = use auto-detection
-+ (default "-1")
-
-- softcarrier Turn the software carrier "on" or "off"
-- (default "on")
-+ softcarrier Turn the software carrier "on" or "off"
-+ (default "on")
-
-- invert "on" = invert the output pin (default "off")
-+ invert "on" = invert the output pin (default "off")
-
-- debug "on" = enable additional debug messages
-- (default "off")
-+ debug "on" = enable additional debug messages
-+ (default "off")
-
-
- Name: mcp2515-can0
- Info: Configures the MCP2515 CAN controller on spi0.0
- Load: dtoverlay=mcp2515-can0,<param>=<val>
--Params: oscillator Clock frequency for the CAN controller (Hz)
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-
-- spimaxfrequency Maximum SPI frequence (Hz)
-+ spimaxfrequency Maximum SPI frequence (Hz)
-
-- interrupt GPIO for interrupt signal
-+ interrupt GPIO for interrupt signal
-
-
- Name: mcp2515-can1
- Info: Configures the MCP2515 CAN controller on spi0.1
- Load: dtoverlay=mcp2515-can1,<param>=<val>
--Params: oscillator Clock frequency for the CAN controller (Hz)
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-
-- spimaxfrequency Maximum SPI frequence (Hz)
-+ spimaxfrequency Maximum SPI frequence (Hz)
-
-- interrupt GPIO for interrupt signal
-+ interrupt GPIO for interrupt signal
-
-
- Name: mmc
- Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
- Load: dtoverlay=mmc,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-- force_pio Disable DMA support
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+ force_pio Disable DMA support
-
-
- Name: mz61581
- Info: MZ61581 display by Tontec
- Load: dtoverlay=mz61581,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- txbuflen Transmit buffer length (default 32768)
-+ txbuflen Transmit buffer length (default 32768)
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- [ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ]
-@@ -474,69 +474,69 @@ Params: speed Display
- Name: piscreen
- Info: PiScreen display by OzzMaker.com
- Load: dtoverlay=piscreen,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: piscreen2r
- Info: PiScreen 2 with resistive TP display by OzzMaker.com
- Load: dtoverlay=piscreen2r,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: pitft28-capacitive
- Info: Adafruit PiTFT 2.8" capacitive touch screen
- Load: dtoverlay=pitft28-capacitive,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- touch-sizex Touchscreen size x (default 240)
-+ touch-sizex Touchscreen size x (default 240)
-
-- touch-sizey Touchscreen size y (default 320)
-+ touch-sizey Touchscreen size y (default 320)
-
-- touch-invx Touchscreen inverted x axis
-+ touch-invx Touchscreen inverted x axis
-
-- touch-invy Touchscreen inverted y axis
-+ touch-invy Touchscreen inverted y axis
-
-- touch-swapxy Touchscreen swapped x y axis
-+ touch-swapxy Touchscreen swapped x y axis
-
-
- Name: pitft28-resistive
- Info: Adafruit PiTFT 2.8" resistive touch screen
- Load: dtoverlay=pitft28-resistive,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-
- Name: pps-gpio
- Info: Configures the pps-gpio (pulse-per-second time signal via GPIO).
- Load: dtoverlay=pps-gpio,<param>=<val>
--Params: gpiopin Input GPIO (default "18")
-+Params: gpiopin Input GPIO (default "18")
-
-
- Name: pwm
-@@ -553,9 +553,9 @@ Info: Configures a single PWM channel
- 4) Currently the clock must have been enabled and configured
- by other means.
- Load: dtoverlay=pwm,<param>=<val>
--Params: pin Output pin (default 18) - see table
-- func Pin function (default 2 = Alt5) - see above
-- clock PWM clock frequency (informational)
-+Params: pin Output pin (default 18) - see table
-+ func Pin function (default 2 = Alt5) - see above
-+ clock PWM clock frequency (informational)
-
-
- Name: pwm-2chan
-@@ -572,11 +572,11 @@ Info: Configures both PWM channels
- 4) Currently the clock must have been enabled and configured
- by other means.
- Load: dtoverlay=pwm-2chan,<param>=<val>
--Params: pin Output pin (default 18) - see table
-- pin2 Output pin for other channel (default 19)
-- func Pin function (default 2 = Alt5) - see above
-- func2 Function for pin2 (default 2 = Alt5)
-- clock PWM clock frequency (informational)
-+Params: pin Output pin (default 18) - see table
-+ pin2 Output pin for other channel (default 19)
-+ func Pin function (default 2 = Alt5) - see above
-+ func2 Function for pin2 (default 2 = Alt5)
-+ clock PWM clock frequency (informational)
-
-
- Name: raspidac3
-@@ -600,15 +600,15 @@ Params: <None>
- Name: rpi-display
- Info: RPi-Display - 2.8" Touch Display by Watterott
- Load: dtoverlay=rpi-display,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: rpi-ft5406
-@@ -632,52 +632,52 @@ Params: <None>
- Name: sdhost
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
- Load: dtoverlay=sdhost,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-
- Name: sdio
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
- and enables SDIO via GPIOs 22-27.
- Load: dtoverlay=sdio,<param>=<val>
--Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- sdio_overclock SDIO Clock (in MHz) to use when the MMC
-- framework requests 50MHz
-+ sdio_overclock SDIO Clock (in MHz) to use when the MMC
-+ framework requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-- poll_once Disable SDIO-device polling every second
-- (default on: polling once at boot-time)
-+ poll_once Disable SDIO-device polling every second
-+ (default on: polling once at boot-time)
-
-- bus_width Set the SDIO host bus width (default 4 bits)
-+ bus_width Set the SDIO host bus width (default 4 bits)
-
-
- Name: sdtweak
- Info: Tunes the bcm2835-sdhost SD/MMC driver
- Load: dtoverlay=sdtweak,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-
- Name: smi
-@@ -708,25 +708,25 @@ Name: tinylcd35
- Info: 3.5" Color TFT Display by www.tinylcd.com
- Options: Touch, RTC, keypad
- Load: dtoverlay=tinylcd35,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- touch Enable touch panel
-+ touch Enable touch panel
-
-- touchgpio Touch controller IRQ GPIO
-+ touchgpio Touch controller IRQ GPIO
-
-- xohms Touchpanel: Resistance of X-plate in ohms
-+ xohms Touchpanel: Resistance of X-plate in ohms
-
-- rtc-pcf PCF8563 Real Time Clock
-+ rtc-pcf PCF8563 Real Time Clock
-
-- rtc-ds DS1307 Real Time Clock
-+ rtc-ds DS1307 Real Time Clock
-
-- keypad Enable keypad
-+ keypad Enable keypad
-
- Examples:
- Display with touchpanel, PCF8563 RTC and keypad:
-@@ -738,9 +738,9 @@ Params: speed Display
- Name: uart1
- Info: Enable uart1 in place of uart0
- Load: dtoverlay=uart1,<param>=<val>
--Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14)
-+Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14)
-
-- rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-+ rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-
-
- Name: vc4-kms-v3d
-@@ -763,22 +763,22 @@ Name: w1-gpio
- Info: Configures the w1-gpio Onewire interface module.
- Use this overlay if you *don't* need a GPIO to drive an external pullup.
- Load: dtoverlay=w1-gpio,<param>=<val>
--Params: gpiopin GPIO for I/O (default "4")
-+Params: gpiopin GPIO for I/O (default "4")
-
-- pullup Non-zero, "on", or "y" to enable the parasitic
-- power (2-wire, power-on-data) feature
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-
-
- Name: w1-gpio-pullup
- Info: Configures the w1-gpio Onewire interface module.
- Use this overlay if you *do* need a GPIO to drive an external pullup.
- Load: dtoverlay=w1-gpio-pullup,<param>=<val>
--Params: gpiopin GPIO for I/O (default "4")
-+Params: gpiopin GPIO for I/O (default "4")
-
-- pullup Non-zero, "on", or "y" to enable the parasitic
-- power (2-wire, power-on-data) feature
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-
-- extpullup GPIO for external pullup (default "5")
-+ extpullup GPIO for external pullup (default "5")
-
-
- Troubleshooting
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-12 01:37:02 +0000