diff options
Diffstat (limited to 'target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch')
| -rw-r--r-- | target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch | 127 |
1 files changed, 0 insertions, 127 deletions
diff --git a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch b/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch deleted file mode 100644 index 7576f61879..0000000000 --- a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch +++ /dev/null @@ -1,127 +0,0 @@ -From 358feb7def17978e9a3c45c1971b42d36ff89545 Mon Sep 17 00:00:00 2001 -From: Michael Heimpold <michael.heimpold@i2se.com> -Date: Fri, 29 Jan 2016 12:00:37 +0100 -Subject: [PATCH] Add overlay and enable support for QCA7000 board - -This adds a device tree overlay for the QCA7000 which can be used -when attaching an I2SE's PLC Stamp micro EVK to the Raspberry Pi. - -This Evaluation Board embeds a QCA7000 chip, a Homeplug Green PHY -powerline chip from Qualcomm/Atheros for the Internet of Things. - -This patch also enables the required QCA7000 driver module -in the default configurations. - -Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> -Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com> ---- - arch/arm/boot/dts/overlays/Makefile | 1 + - arch/arm/boot/dts/overlays/README | 8 ++++ - arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 ++++++++++++++++++++++++++ - arch/arm/configs/bcm2709_defconfig | 1 + - arch/arm/configs/bcmrpi_defconfig | 1 + - 5 files changed, 63 insertions(+) - create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts - ---- a/arch/arm/boot/dts/overlays/Makefile -+++ b/arch/arm/boot/dts/overlays/Makefile -@@ -48,6 +48,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pitft28-resis - dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo - dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo - dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo -+dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo - dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo - dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo - dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo ---- a/arch/arm/boot/dts/overlays/README -+++ b/arch/arm/boot/dts/overlays/README -@@ -625,6 +625,14 @@ Params: pin Output p - clock PWM clock frequency (informational) - - -+Name: qca7000 -+Info: I2SE's Evaluation Board for PLC Stamp micro -+Load: dtoverlay=qca7000,<param>=<val> -+Params: int_pin GPIO pin for interrupt signal (default 23) -+ -+ speed SPI bus speed (default 12 MHz) -+ -+ - Name: raspidac3 - Info: Configures the RaspiDAV Rev.3x audio card - Load: dtoverlay=raspidac3 ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts -@@ -0,0 +1,52 @@ -+// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK -+// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ status = "okay"; -+ -+ spidev@0 { -+ status = "disabled"; -+ }; -+ -+ eth1: qca7000@0 { -+ compatible = "qca,qca7000"; -+ reg = <0>; /* CE0 */ -+ pinctrl-names = "default"; -+ pinctrl-0 = <ð1_pins>; -+ interrupt-parent = <&gpio>; -+ interrupts = <23 0x1>; /* rising edge */ -+ spi-max-frequency = <12000000>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ eth1_pins: eth1_pins { -+ brcm,pins = <23>; -+ brcm,function = <0>; /* in */ -+ brcm,pull = <0>; /* none */ -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ int_pin = <ð1>, "interrupts:0", -+ <ð1_pins>, "brcm,pins:0"; -+ speed = <ð1>, "spi-max-frequency:0"; -+ }; -+}; ---- a/arch/arm/configs/bcm2709_defconfig -+++ b/arch/arm/configs/bcm2709_defconfig -@@ -446,6 +446,7 @@ CONFIG_NETCONSOLE=m - CONFIG_TUN=m - CONFIG_VETH=m - CONFIG_ENC28J60=m -+CONFIG_QCA7000=m - CONFIG_MDIO_BITBANG=m - CONFIG_PPP=m - CONFIG_PPP_BSDCOMP=m ---- a/arch/arm/configs/bcmrpi_defconfig -+++ b/arch/arm/configs/bcmrpi_defconfig -@@ -439,6 +439,7 @@ CONFIG_NETCONSOLE=m - CONFIG_TUN=m - CONFIG_VETH=m - CONFIG_ENC28J60=m -+CONFIG_QCA7000=m - CONFIG_MDIO_BITBANG=m - CONFIG_PPP=m - CONFIG_PPP_BSDCOMP=m |