summaryrefslogtreecommitdiffstats
path: root/config/Config-images.in
Commit message (Collapse)AuthorAgeFilesLines
...
* config: support new symbol intro'd in kernel 4.12Koen Vandeputte2018-01-131-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the bootloader. By default, all symbols containing INITRAMFS are wiped from the final config and then re-added conditionally. Add support for this symbol, as the build will stop otherwise questioning the user about this option: * Restart config... * * * General setup * Cross-compiler tool prefix (CROSS_COMPILE) [] Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n ... Initial RAM filesystem and RAM disk (initramfs/initrd) support (BLK_DEV_INITRD) [Y/n/?] y Initramfs source file(s) (INITRAMFS_SOURCE) [] Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE) [N/y/?] (NEW) Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: Enable initramfs for p1020 subtargetChris Blake2017-10-141-0/+1
| | | | | | | The following patch enables building of initramfs images by default for the P1020 subtarget in mpc85xx. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* build: enable gzipping of images on x86 even if ext4 is disabledFelix Fietkau2017-07-061-1/+1
| | | | | | | There is lots of padding between the boot partition and the rootfs, so gzipping is helpful here Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: allow specifying flow-control to grub on serial consolePhilip Prindeville2017-04-031-0/+5
| | | | | | | On the more sophisticated (i.e. deeper FIFO) serial controllers, flow-control might be needed to avoid dropping output. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* x86: Set default baud rate on Geode images to 115200David Woodhouse2017-02-171-1/+0
| | | | | | | | | | | Prior to commit 1496b95a0 ("x86: clean up default grub baudrate settings") we had three different baud rates for the Geode targets: 19200 for net5501, 38400 for alix2, and 115200 for Geos. It doesn't seem that there's a very good reason for varying from our default 115200 baud, so let's make the Geode target do that instead. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* x86: revert default root size back to 256 MBFelix Fietkau2016-12-151-2/+1
| | | | | | | | | | | 2 GB is overkill and was only added to allow unlimited ext4 resizing, which is a pretty rare use case. 256 MB allows resizing up to 256 GB, which should be good enough for almost all users. A lot of this is mostly irrelevant anyway, since you can just use squashfs + ext4 overlay. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uml: clean up the kernel config and add squashfs+ext4/f2fs supportFelix Fietkau2016-11-241-1/+1
| | | | | | Replaces plain ext4 images Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86: bump default kernel partition size to 16MFelix Fietkau2016-11-091-1/+1
| | | | | | | This leaves more room for sysupgrade config data or for having multiple kernel images to choose from Signed-off-by: Felix Fietkau <nbd@nbd.name>
* config: ext4: increase x86 rootfs size to 2GB to support online resize2fsJo-Philipp Wich2016-10-271-1/+2
| | | | | | | | | | | | | | | | | | | The current default rootfs size of 256MB in conjunction with 4K blocks produces an ext4 filesystem which lacks the appropriate amount of backup GDT entries to support online-resizing. For x86 targets, increase the default rootfs size to 2048MB which allows online resizing the filesystem to up to 2TB which is the current theoretical maximum for LEDE, due to missing GPT support on the root block device. Note that the filesystem artefact will not occupy 2GB on the build system as the make_ext4fs utility uses sparse files to generate the filesystem images, so the actual disk usage is much lower. Furthermore the filesystem images are gzip compressed, shrinking them to only a few megabytes on the download server. Signed-off-by: Jo-Philipp Wich <jo@mein.io> Acked-by: Michael Heimpold <mhei@heimpold.de>
* config: ext4: drop option to set maximum number of inodesJo-Philipp Wich2016-10-271-7/+0
| | | | | | | | | | | There is very little practical use to limit the number of available inodes on an ext4 filesystem and the make_ext4fs utility is able to calculate useful defaults by itself. Drop the option to make resulting ext4 filesystems more flexible by default. Signed-off-by: Jo-Philipp Wich <jo@mein.io> Acked-by: Michael Heimpold <mhei@heimpold.de>
* images: bump default rootfs size to 256 MBFelix Fietkau2016-09-081-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add sdcard image creation scriptJosua Mayer2016-09-021-1/+1
| | | | | | | | | | | | | | | | Added gen_mvebu_sdcard_img.sh to facilitate creating an fixed-size sdcard image, adding the bootloader and populating it with actual data. Added the required rules for creating a 4GB sdcard image according to this layout: p0: boot (fat32) p1: rootfs (squashfs) p2: rootfs_data (ext4) This should be generic to any mvebu boards that can boot from block storage. Added the new sdcard image to the Clearfog image profile. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
* apm821xx: use lzma compression for the initramfs imagesChristian Lamparter2016-07-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | The MR24's u-boot takes it sweet time decompressing the LZMA-packed initramfs image. A user reported that compared to the old gzip method in v2: it "takes a ton longer to decompress like 4\x the old boot time for decompression". This patch also fixes a issue with the WNDR4700's initramfs image getting to big and causing the following u-boot crash during the decompression: "Uncompressing Multi-File Image ... Error: inflate() returned -5 out-of-mem or overwrite error - must RESET board to recover" This patch fixes both issues by reverting the MR24's initramfs compression method back to gzip. And choosing to compress the initramfs within the initramfs image as LZMA by default. Cc: chrisrblake93@gmail.com Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* config: remove options for including kernel/dtb in rootfsFelix Fietkau2016-07-201-41/+0
| | | | | | These options were a big design flaw to begin with Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: make TARGET_ROOTFS_JFFS2 depend on USES_JFFS2Felix Fietkau2016-07-201-1/+1
| | | | | | | If jffs2 support was not enabled by the target, jffs2 are quite likely to be broken, so we shouldn't build them. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: remove leftover dependenices on TARGET_rdcFelix Fietkau2016-05-121-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86: clean up default grub baudrate settingsFelix Fietkau2015-03-291-4/+3
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 45113
* build: remove leftover olpc support codeFelix Fietkau2015-03-281-4/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 45084
* x86: use PARTUUID instead explicitly specifying the device by defaultJo-Philipp Wich2015-03-241-2/+0
| | | | | | | | | | | | | This changes the x86 image generation to match x86_64, using the PARTUUID for the rootfs instead of explicitly configuring the device. It unbreaks KVM with VirtIO, which uses /dev/vda2 instead of /dev/sda2. Tested in QEMU/KVM with VirtIO, VirtualBox and VMware. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 44966
* config: use PARTUUID by default on x86_64Jo-Philipp Wich2014-10-271-3/+4
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 43086
* Kconfig: Various typo/grammar/line-length fixes in Config*.in filesHauke Mehrtens2014-09-131-17/+17
| | | | | | | | | | | | | Non-functional changes to config/Config-*.in files, including: * spelling mistakes * inconsistent terminology * grammar * overly long lines in "help" components Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> SVN-Revision: 42519
* x86: add back a line accidentally removed in r41763Felix Fietkau2014-07-201-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 41764
* x86: remove the arbitrary limitation of vmware/virtualbox images to ext4, ↵Felix Fietkau2014-07-201-3/+2
| | | | | | | | select TARGET_IMAGES_PAD instead Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 41763
* config/Config-images.in: enable zlib as the default ubi compressionJohn Crispin2014-06-241-1/+1
| | | | | | | | http://patchwork.openwrt.org/patch/5686/ Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41329
* build: set default squashfs block size to 64k for low-memory systemsFelix Fietkau2014-06-021-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 40981
* build: make the squashfs block size configurableFelix Fietkau2014-06-021-1/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 40979
* config/Config-images.in: the ext4 series introduced a regressionJohn Crispin2014-06-021-3/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 40951
* image: ext4: rename config options as these are only used for ext4 image ↵John Crispin2014-06-021-2/+2
| | | | | | | | creation Signed-off-by: Michael Heimpold <mhei@heimpold.de> SVN-Revision: 40926
* image: ext4: allow creation of a journaling filesystemJohn Crispin2014-06-021-0/+7
| | | | | | Signed-off-by: Michael Heimpold <mhei@heimpold.de> SVN-Revision: 40925
* image: ext4: allow to choose a block size for the rootfsJohn Crispin2014-06-021-0/+24
| | | | | | Signed-off-by: Michael Heimpold <mhei@heimpold.de> SVN-Revision: 40924
* image: ext4: move ext4 specific options into submenuJohn Crispin2014-06-021-15/+16
| | | | | | Signed-off-by: Michael Heimpold <mhei@heimpold.de> SVN-Revision: 40923
* config: don't use /dev/vda2 for kvm guest, its not used since a long timeJo-Philipp Wich2014-05-131-2/+1
| | | | SVN-Revision: 40756
* add x86_64 target supportImre Kaloz2014-01-071-3/+3
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39208
* virtualbox emulates the e1000 for a long time nowImre Kaloz2014-01-071-1/+1
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39207
* move most of the x86 image generation options to the main fileImre Kaloz2014-01-071-1/+80
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39206
* move menuconfig options into separate filesImre Kaloz2013-11-221-0/+201
Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 38895
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-17 06:03:35 +0000