summaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood
Commit message (Collapse)AuthorAgeFilesLines
...
* kirkwood: set testing kernel version to 5.15Pawel Dembicki2022-05-011-0/+1
| | | | | | | | | This patch configures kernel testing version for kirkwood target. Compile tested: all Run tested: Endian 4i Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: refresh 5.15 kernel configPawel Dembicki2022-05-011-5/+7
| | | | | | Done by "make kernel_oldconfig". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: copy config and patches to 5.15Pawel Dembicki2022-05-0117-0/+1264
| | | | | | | | This patch makes only a copy of 5.10 config and patches. Patches merged in upstream was omited. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* target/linux: replace egrep with grep -ERosen Penev2022-02-071-1/+1
| | | | | | | egrep is deprecated and replaced by grep -E. The latter is used throughout the tree. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: add disabled POWER_RESET_QNAPSungbo Eo2022-01-291-1/+0
| | | | | | Move the disabled symbol from target configs to generic configs. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: add support for ipTIME NAS1Sungbo Eo2022-01-296-0/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC. Specifications: * SoC: 88F6281 * RAM: 256 MiB * Flash: SPI NOR 16 MiB * SATA: 1x 3Gb/s * Ethernet: 1x 1GbE * USB: 1x 2.0 * Fan: 2 speed level * UART: JP1 (115200 8N1) * Pinout: [3V3] (TXD) (RXD) (GND) Notes: * There are several variants of the model name: "NAS-I", "NASI", "NAS1". Here "NAS1" is adopted for consistent naming scheme. * The reset button is also a USB copy button in stock FW, but in this patch the former is the only default behavior. Installation via web interface: 1. Flash sysupgrade image through the stock web interface. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: rework 02_networkSungbo Eo2022-01-291-42/+67
| | | | | | | Just like other targets do, introduce two setup functions for interfaces and MAC addresses. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: drop kernel 5.4 supportSungbo Eo2022-01-2920-1937/+0
| | | | | | | It has been 3 months since we switched this target to 5.10, now we can remove the 5.4 files. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: bump 5.10 to 5.10.90Rui Salvaterra2022-01-072-15/+5
| | | | | | | | Add and enable a new kconfig knob to disable unprivileged eBPF by default. Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.4 to 5.4.170John Audia2022-01-072-15/+5
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/mt7621 Signed-off-by: John Audia <graysky@archlinux.us>
* kirkwood: add support for two clones from EndianPawel Dembicki2021-12-294-0/+241
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | They are Endian 4i Edge 200 and his clone Endian UTM Mini. Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 512MB (Micron 29F4G08AAC) - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2) - Lan 5: 1x GBE (Marvell 88E1116R-NNC1) - Storage: MicroSD Slot - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN) - USB: 1x USB 2.0 port - Console: RJ-45 port - LEDs: 3x GPIO controlled Notes: - WLAN led (Endian UTM Mini) is drived by MPCIE card Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv usb reset fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: add support for NETGEAR ReadyNAS Duo v2Pawel Dembicki2021-12-2912-2/+600
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6282 (1.6 GHz) - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 1x USB 2.0 - 2x USB 3.0 - 2x SATA - 3x button - 5x leds - serial on J5 connector accessible from rear panel (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!) Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: usb reset setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Known issues: - Power button and PHY INTn pin are connected to the same GPIO. It causes that every network restart button is pressed in system. As workaround, button is used as regular BTN_1. For more info please look at file: RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c from Netgear GPL sources. Tested-by: Raylynn Knight <rayknight@me.com> Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: 5.10: consolidate mac80211 crypto optionsSergey Ryazanov2021-12-171-2/+0
| | | | | | | | | | | | | | | | | | | | | | Each of - CRYPTO_AEAD2 - CRYPTO_AEAD - CRYPTO_GF128MUL - CRYPTO_GHASH - CRYPTO_HASH2 - CRYPTO_HASH - CRYPTO_MANAGER2 - CRYPTO_MANAGER - CRYPTO_NULL2 either directly required for mac80211 crypto support, or directly selected by such options. Support for the mac80211 crypto was enabled in the generic config since c7182123b9 ("kernel: make cryptoapi support needed by mac80211 built-in"). So move the above options from the target configs to the generic config to make it clear why do we need them. CC: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-171-1/+0
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kirkwood: add support for Ctera C200 V1 NASPawel Dembicki2021-12-046-1/+421
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 256MB (Samsung 216 K9F2G08U0C) - Lan: 1x GBE (Marvell 88E1116R-NNC1) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 2.0 port - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ctera_c200-v1_back_to_factory Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> [apply sorting to device recipe] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: sysupgrade: drop unnecessary UBI to UBI logicBjørn Mork2021-12-031-18/+1
| | | | | | | | | | | | | The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kirkwood: switch to kernel 5.10Adrian Schmutzler2021-10-091-2/+1
| | | | | | | This target has testing support for more than half a year now. Time to switch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: refresh kernel configSungbo Eo2021-10-031-3/+7
| | | | | | | Refresh config with make kernel_oldconfig. Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: solidify SATA_PMP configSungbo Eo2021-10-031-0/+1
| | | | | | | | | | | | | | | | | | | SATA_PMP option is no longer exposed when no SATA host driver is enabled since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option selectable only if any SATA host driver is enabled"). Commit 1bb3f593ee73 ("kirkwood: update config for kernel 5.10") manually added CONFIG_SATA_PMP=y to config file, but the config will disappear for every kernel_oldconfig refresh. To prevent this, a small hack is added, which selects SATA_HOST automatically when SATA_PMP is enabled. This patch can be dropped if SATA_MV is ever re-added into kernel config file. Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run> [Move patch to generic/hack-5.10] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kirkwood: increase kernel size of LinksysesPawel Dembicki2021-09-135-30/+47
| | | | | | | | | | | | | | Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel partition size when kernel 5.10 is used. This patch change kernel partition to maximum size allowed by u-boot. Kernel size is overlapping rootfs now, like mvebu Linksyses and stock partition table. It fix back to stock via sysupgrade, which was broken since 18.06. Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9") Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* treewide: do not quote compatible in shell scriptsAdrian Schmutzler2021-06-061-18/+18
| | | | | | | The compatible is a literal string without any problematic characters, so there is no reason to quote it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-064-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix parsing fixed subpartitionsRafał Miłecki2021-05-062-4/+4
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-212-4/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove redundant ubifs kconfig symbolsRui Salvaterra2021-04-212-6/+0
| | | | | | | For the targets which enable ubifs, these symbols are already part of the generic kconfigs. Drop them from the target kconfigs. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: backport 5.13 mtd partitioning changesRafał Miłecki2021-03-292-8/+8
| | | | | | | | 1. Use upstream accepted NVMEM patches 2. Minor fix for BCM4908 partitioning 3. Support for Linksys firmware partitions on Northstar Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add pending mtd patches adding NVMEM supportRafał Miłecki2021-03-122-4/+4
| | | | | | | | It's meant to provide upstream support for mtd & NVMEM. It's required e.g. for reading MAC address from mtd partition content. It seems to be in a final shape so it's worth testing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-064-4/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: add the latest mtd patch extending ofpart parserRafał Miłecki2021-03-012-12/+12
| | | | | | | | | | | | This adds the latest version of ofpart commit. It hopefully 1. Doesn't break compilation 2. Doesn't break partitioning (this time). It's required to implement fixed partitioning with some quirks. It's required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kirkwood: set testing kernel version to 5.10Sungbo Eo2021-02-241-0/+1
| | | | | | | | | | | | Tested on Pogoplug V4. Linksys EA3500 will not build with buildbot settings and should be disabled when the target is switched, unless the image size is reduced again. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [add EA3500 comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: update config for kernel 5.10Sungbo Eo2021-02-241-5/+7
| | | | | | | | | | | Update config with make kernel_oldconfig. CONFIG_SATA_PMP=y is added manually as done for 5.4. This should be resolved properly in a separate issue. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [add back CONFIG_SATA_PMP, rebase/refresh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: refresh patches for kernel 5.10Sungbo Eo2021-02-243-487/+2
| | | | | | | Refresh patches to make them apply to kernel 5.10. The removed patch has been merged upstream. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: copy files to kernel 5.10Sungbo Eo2021-02-2416-0/+1614
| | | | | | Copy config and patches to kernel 5.10. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: add further missing symbolsAdrian Schmutzler2021-02-241-1/+0
| | | | | | | | | | | CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config. CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package, but got removed there without moving the symbol to generic config. Fixes: dd13add3ceed ("kernel: i2c-pxa: remove slave") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: rename files-5.4 to filesSungbo Eo2021-02-197-0/+0
| | | | | | | Move local DTS files from "files-5.4" to "files" directory so kernel 5.10 can use it. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-102-8/+3
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: use 3 temperature sensors for Zyxel NSA310BThomas Beckler2021-02-051-4/+16
| | | | | | | | | | | | | | | | | | | | Instead of taking the input of one temperature sensor (temp1), the script takes into account three temperature sensors to control the PWM of the cooling fan. temp1 -> placed on main board temp2 -> placed on main board temp3 -> placed on or close to chipset All three temperatures give valid input for the PWM of the fan on NSA310 and are actually changing. Tested on two NSA310. Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com> Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com> [commit title/message facelift, code cleanup] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: refresh kernel configSungbo Eo2021-02-051-63/+2
| | | | | | Refresh config with make kernel_oldconfig. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: remove generic profileAdrian Schmutzler2021-01-271-17/+0
| | | | | | | | | | | On a platform with many very different devices, like found on kirkwood, the generic profile seems like a remnant of the past that does not have a real use anymore. Remove it to have one thing less to maintain. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: add support for Seagate BlackArmor NAS220Kip Porterfield2020-12-224-0/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Seagate BlackArmor NAS220 is a consumer NAS with two internal drive bays. The stock OS runs RAID 1 over the disks via mdadm. Device specification: - SoC: Marvell 88F6192 800 MHz - RAM: 128 MB - Flash: 32 MB - 2 x internal SATA II drives - Ethernet: 10/100/1000 Mbps (single port, no switch) - WLAN: None - LED: Power, Status, Sata Activity - Key: Power, Reset - Serial: 10 pin header, (115200,8,N,1), 3.3V TTL 9|x - x|10 7|x - x|8 5|x - GND|6 3|x - RX|4 1|TX - x|2 front of case - USB ports: 2 x USB 2.0 Flash instruction: NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables TFTP server setup - Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server - Copy these files to TFTP server location - u-boot.kwb - seagate_blackarmor-nas220-initramfs-uImage - seagate_blackarmor-nas220-squashfs-sysupgrade.bin - seagate_blackarmor-nas220-squashfs-factory.bin Seagate NAS setup - Connect LAN cable between PC and seagate device - Connect to serial to seagate device Install u-boot - Boot seagate device and stop in bootloader by pressing any key - run 'printenv' from u-boot and save the values - tftpboot 0x2000000 u-boot.kwb - nand erase.part uboot - nand write 0x2000000 0x0 ${filesize} - reset Update MAC address in u-boot env - Stop in u-boot by pressing any key - Get your MAC address from your saved printenv. Is also on chassis - setenv ethaddr <your MAC> - saveenv Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade - tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage - bootm 0x2000000 - *OpenWrt should be running now, however it is not written to flash yet* - From the running instance of OpenWrt use Luci's "flash image" feature from the web site or use sysupgrade from the console to write seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash Option 2 - Install OpenWrt by flashing factory image from u-boot - nand erase.part ubi - tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin - nand write 0x2000000 ubi ${filesize} - reset Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-221-3/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* target: update SPDX license namesAdrian Schmutzler2020-09-222-2/+2
| | | | | | | SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to GPL-2.0-or-later. Reflect that in the SPDX license headers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: revert sysupgrade adjustments for early DSA-adoptersAdrian Schmutzler2020-09-081-16/+0
| | | | | | | | | | | | | | | | | The uci-default mechanism to update the compat-version was only meant for early DSA-adopters, which should have updated by now. Remove this workaround again in order to prevent the intended experiences for all the other people. This reverts: a9703db72030 ("mvebu: fix sysupgrade experience for early DSA-adopters") 86c89bf5e8f5 ("kirkwood: fix sysupgrade experience for early DSA-adopters") Partially reverted: 1eac573b5304 ("ramips: mt7621: implement compatibility version for DSA migration") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "treewide: add sysupgrade comment for early DSA-adopters"Adrian Schmutzler2020-09-081-2/+1
| | | | | | | | | | This reverts commit e81e625ca375d6dc3c885ec870ec15757ac76d72. This was meant just for early DSA-adopters. Those should have updated by now, remove it so future updaters get the intended experience. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-202-3/+3
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: add sysupgrade comment for early DSA-adoptersAdrian Schmutzler2020-08-081-1/+2
| | | | | | | | | | Add a specific comment for early DSA-adopters that they can keep their config when prompted due to compat-version increase. This is a temporary solution, the patch should be simply reverted before any release. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: fix sysupgrade experience for early DSA-adoptersAdrian Schmutzler2020-08-081-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conceptually, the compat-version during sysupgrade is meant to describe the config. Therefore, if somebody starts with a device on 19.07 and swconfig, and that person does a forceful upgrade into a DSA-based firmware without wiping his/her config, then the local compat-version should stay at 1.0 according to the config present (and not get updated). However, this poses a problem for those people that early-adopted DSA in master, as they already have adjusted their config for DSA, but it still is "1.0" as far as sysupgrade is concerned. This can be healed by a simple uci set system.@system[0].compat_version="1.1" uci commit system But this needs to be applied _after_ the upgrade (as the "old" fwtool on the old installation does not know about compat_version) and it requires access via SSH (i.e. no pure GUI solution is available for this group of people, apart from wiping their config _again_ for no technical reason). Despite, the situation will not become obvious to those just upgrading via GUI, they will just have the experience of a "broken upgrade". This is a conflict which cannot be resolved by achieving both goals, we have to decide to either keep the strict concept or improve the situation for early adopters. In this patch, we address the issue by providing a uci-defaults script that will raise the compat_version for _all_ people upgrading into a 1.1 image, no matter whether they have reset config or not. The idea is to implement this as a _temporary_ solution, so early adopters can upgrade into the new mechanism without issues, and after a few weeks/months we could remove the uci-defaults script again. If we e.g. remove the script just before 20.xx.0-rc1, early adopters should have moved on by then, and existing stable users would still get the intended experience. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTSAdrian Schmutzler2020-08-031-16/+14
| | | | | | | | | | | Since most of the DTS file names follow a common scheme now, let's update the automatically generated DEVICE_DTS value and get rid of some DEVICE_DTS and all BOARD_NAME entries for individual devices. This should specifically make the job easier for developers adding new devices, as they are not tempted to copy over BOARD_NAME anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 23:53:44 +0000