summaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: update patch add PWM support for MT7981Daniel Golle2023-05-181-119/+29
| | | | | | Update patch with version submitted upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for the GL.iNet GL-MT3000Daniel Golle2023-05-184-3/+295
| | | | | | | | | | | | | | | | | | | | | | The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 256 MiB Macronix SPI NAND - RAM: 512 MiB Nanya DDR4 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN) - Ethernet: - 1x 10/100/1000 Mbps built-in PHY (LAN) - 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN) - USB 3.0 port - Buttons: 1 button, 1 switch - LEDs: 1x light-blue, 1x warm-white - Serial console: internal 4-pin header, 115200 8n1 - PWM controlled fan with tacho - Power: 5 VDC, 3 A (USB Type-C) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Cudy WR3000 v1David Bauer2023-05-186-0/+318
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7981 WiSoC 256MB DDR3 RAM 16MB SPI-NOR (XMC XM25QH128C) MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5) UART: 115200 8N1 3.3V [LEDS] VCC-GND-RX-TX [ETH] Header is located below the heatsink Case ---- Unscrew the 4 bottom screws. Remove the top of the case by inserting a small screwdriver into the ventilation holes and lift the top cover. This works best by beginning near the ETH-ports. The top is clipped on the front near the LEDs with two plastic clips. The back has a single clip in the middle. Start at one of the back edges. MAC-Addresses ------------- 80:AF:CA:00:F9:C6 LAN 80:AF:CA:00:F9:C7 WAN 80:AF:CA:00:F9:C6 W2 82:AF:CA:30:F9:C6 W5 Installation ------------ 1. Connect to the serial port as described in the "Hardware" section. 2. Power on the device. Keep pressing the "0" key to enter the U-Boot shell. 3. Download the OpenWrt initramfs image. Place it on an TFTP server connected to the Cudy LAN ports. Make sure the server is reachable at 192.168.1.2. Rename the image to "cudy3000.bin" 4. Download and boot the OpenWrt initramfs image. $ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000 5. Transfer the OpenWrt sysupgrade image to the device using scp. Install with sysupgrade. Note: Cudy does not yet provide a image for disabling their signature-protection. This has happened in the past. Make sure to check the wiki for a possible easier installation method. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: fix typoDavid Bauer2023-05-181-1/+1
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* bmips: improve kernel patchesÁlvaro Fernández Rojas2023-05-1714-185/+181
| | | | | | | Add missing patch headers and regenerate the ones that contain an obsolete patch header. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: add support for MikroTik RB951Ui-2HnDMichał Kępień2023-05-166-0/+168
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951Ui-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit d19b868b12 ("ar71xx: Add support for MikroTik RB951Ui-2HnD"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8229 switch, 5x 10/100 Mbit/s - 1x PoE in (port 1, 8-30 V input) - 1x PoE out (port 5, 500 mA output) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 9x LED: - 1x power (green, not configurable) - 1x user (green) - 5x FE ports (green) - 1x wireless (green) - 1x PoE out (red) - 1x button (restart) See https://mikrotik.com/product/RB951Ui-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* generic: mtk_eth_soc: don't crash if WO firmware is missingDaniel Golle2023-05-151-0/+28
| | | | | | | Import patch to prevent crashes in case WO firmware is missing on devices with only a single frontend (eg. MT7981+MT7976). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: add support for wireless offloading on MT7981Daniel Golle2023-05-152-1/+47
| | | | | | Load appropriate firmware for wireless offloading on MT7981. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: mikrotik: bump compat version for yafut imagesThibaut VARÈNE2023-05-151-0/+4
| | | | | | | | | | | | | | | | | | | | | | | Following 5264296, Mirotik NAND devices now use yafut to flash the kernel on devices. This method is incompatible with the old-style "kernel2minor" flash mechanism. Even though NAND images were disabled in default build since 21.02, a user flashing a new-style image onto an old-style image would result in in a soft-brick[1]. In order to prevent such accidental mishap, especially as these device images will be reenabled in the upcoming release, bump the compat version. After the new image is flashed, the compat version can be updated: uci set system.@system[0].compat_version='1.1' uci commit [1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262 Cc: Michał Kępień <openwrt@kempniu.pl> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Robert Marko <robimarko@gmail.com>
* bcm47xx: Refresh patchesHauke Mehrtens2023-05-141-1/+1
| | | | | | | | Refresh patches to make them cleanly apply. This problem was found by the github CI. Fixes: ecd9abc8c082 ("kernel: use upstream firmware patch for Broadcom's NVRAM") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport NVMEM patch for Broadcom's NVRAM MAC cellsRafał Miłecki2023-05-141-0/+77
| | | | | | | It has just been queued for the v6.5. It allows Ethernet drivers to read MACs from NVRAM using NVMEM interface. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: use upstream firmware patch for Broadcom's NVRAMRafał Miłecki2023-05-143-92/+100
| | | | | | This replaces our 2 downstream patches. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mpc85xx: add support for Aerohive BR200-WPPawel Dembicki2023-05-149-5/+544
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive BR200-WP router to OpenWrt under the mpc85xx/p1010 subtarget. Hardware: - SoC: Freescale P1011 - NOR: Intel JS28F512M29EWH 64MB - Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - 2x LEDs - 1x Button - PoE PSE Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; setenv serverip 192.168.1.3; tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin; bootm 0x2004000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NOR. Note: MAC assigns are taken from stock firmware: Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID -------- -------------- -------- ----- ----------- ---- ---------- ---------- --------- Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 - Eth0 08ea:44XX:XXc0 wan U - - - - - Eth1 08ea:44XX:XXc2 access D - - - hive0 - Eth2 08ea:44XX:XXc3 access D - - - hive0 - Eth3 08ea:44XX:XXc4 access D - - - hive0 - Eth4 08ea:44XX:XXc5 access D - - - hive0 - Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - - Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 - Note2: PoE PSE could be managed with `realtek-poe` package. Example port config: config port option enable '1' option id '4' option name 'lan2' option poe_plus '0' option priority '2' config port option enable '1' option id '3' option name 'lan1' option poe_plus '0' option priority '1' Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (switch@0 -> switch@10, Device's quickstart says LEDs are amber and white => add function+color properties but keep labels around, use pr_info) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kirkwood: Replace dtses with upstream acceptedPawel Dembicki2023-05-149-792/+1020
| | | | | | | | | | | | DTSes from of three boards was sent and accpeted upstream. Let's use backport patches with small OpenWrt tweak like other upstream stuff. List of boards: - Zyxel NSA310S - Endian 4i Edge 200 - Ctera C-200 V1 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: add Cisco Meraki MR18Christian Lamparter2023-05-146-1/+427
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz RAM: 2x Winbond W9751G6KB-25 (128 MiB) FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB) WIFI1: Atheros AR9550 5.0GHz (SoC) WIFI2: Atheros AR9582-AR1A 2.4GHz WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN) LED: 1x Power-LED, 1 x RGB Tricolor-LED INPUT: One Reset Button UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8 (VCC, RX, TX, GND - VCC is closest to the boot set jumper under the console pins.) Flashing instructions: Depending on the installed firmware, there are vastly different methods to flash a MR18. These have been documented on: <https://openwrt.org/toh/meraki/mr18> Tip: Use an initramfs from a previous release and then use sysupgrade to get to the later releases. This is because the initramfs can no longer be built by the build-bots due to its size (>8 MiB). Note on that: Upgrades from AR71XX releases are possible, but they will require the force sysupgrade option ( -F ). Please backup your MR18's configuration before starting the update. The reason here is that a lot of development happend since AR71XX got removed, so I do advise to use the ( -n ) option for sysupgrade as well. This will cause the device to drop the old AR71xx configuration and make a new configurations from scratch. Note on LEDs: The LEDs has changed since AR71XX. The white LED is now used during the boot and when upgrading instead of the green tricolor LED. The technical reason is that currently the RGB-LED is brought up later by a userspace daemon. (added warning note about odm-caldata partition. remove initramfs - it's too big to be built by the bots. MerakiNAND -> meraki-header. sort nu801's targets) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: ar934x: still advertise subpage on soft eccChristian Lamparter2023-05-141-3/+3
| | | | | | | | | | This sort of reverts Koen Vandeputte's commit 6561ca1fa51 ("ath79: ar934x: fix mounting issues if subpage is not supported") since it does not work on the MR18 as the UBI is coming from Meraki in that way and it used to work with AR71XX before. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: nand: enable software BCH supportChristian Lamparter2023-05-141-0/+1
| | | | | | | This is necessary to support the Meraki MR18 and likely Z1 as well. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: set 2048B ECC size for Mikrotik boards using soft ECCLech Perczak2023-05-142-0/+2
| | | | | | | | | | | | | Two Mikrotik board families (SXT 5nD R2 and Routerboard 92x are using software ECC on NAND. Some of them use chips capable of subpage write, others do not - within the same family, and a common block size is required for UBI, to avoid mounting errors. Set the ECC step size explicitly for them to 2048B, so UBI can mount existing volumes without problems, at the same time allowing to unlocking subpage write functionality, reuqired for Meraki MR18. Fixes: 6561ca1fa51 ("ath79: ar934x: fix mounting issues if subpage is not supported") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* apm821xx: rename MerakiNAND -> meraki-headerChristian Lamparter2023-05-141-2/+2
| | | | | | | specify that this functions adds a Cisco Meraki special-sauce header for their custom loader/uboot. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.15 to 5.15.111John Audia2023-05-1349-3661/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: 01. backport-5.15/424-v6.4-0001-mtd-core-provide-unique-name-for-nvmem-device-take-t.patch 02. backport-5.15/424-v6.4-0002-mtd-core-fix-nvmem-error-reporting.patch 03. generic-backport/424-v6.4-0003-mtd-core-fix-error-path-for-nvmem-provider.patch 04. generic-backport/828-v6.4-0001-of-Fix-modalias-string-generation.patch 05. bcm4908/patches-5.15/031-v5.17-0002-arm64-dts-broadcom-bcm4908-add-DT-for-Netgear-RAXE50.patch 06. bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit 07. bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgita 08. bcm4908/patches-5.15/033-v6.0-0010-arm64-dts-Add-base-DTS-file-for-bcmbca-device-Asus-G.patchgit 09. bcm4908/patches-5.15/034-v6.1-0005-arm64-dts-Move-BCM4908-dts-to-bcmbca-folder.patch 10. bcm4908/patches-5.15/036-v6.4-0002-arm64-dts-broadcom-bcmbca-bcm4908-fix-NAND-interrupt.patch 11. bcm4908/patches-5.15/036-v6.4-0004-arm64-dts-broadcom-bcmbca-bcm4908-fix-procmon-nodena.patch 12. ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch Manually rebased: bcm27xx/patches-5.15/950-0078-BCM2708-Add-core-Device-Tree-support.patch bcm27xx/patches-5.15/950-0547-ARM-dts-Add-Pi-Zero-2-support.patch bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgit bcm4908/patches-5.15/030-v5.16-0001-arm64-dts-broadcom-bcm4908-Fix-NAND-node-name.patch bcm4908/patches-5.15/032-v5.18-0002-arm64-dts-broadcom-bcm4908-add-pinctrl-binding.patch bcm4908/patches-5.15/032-v5.18-0003-arm64-dts-broadcom-bcm4908-add-watchdog-block.patch bcm4908/patches-5.15/032-v5.18-0004-arm64-dts-broadcom-bcm4908-add-I2C-block.patch bcm4908/patches-5.15/033-v6.0-0003-ARM64-dts-Add-DTS-files-for-bcmbca-SoC-BCM6858.patchgit bcm4908/patches-5.15/033-v6.0-0008-arm64-dts-broadcom-bcm4908-Fix-timer-node-for-BCM490.patchgit bcm4908/patches-5.15/034-v6.1-0001-arm64-dts-broadcom-bcm4908-add-remaining-LED-pins.patch bcm4908/patches-5.15/034-v6.1-0002-arm64-dts-broadcom-bcm4908-add-LEDs-controller-block.patch bcm4908/patches-5.15/034-v6.1-0003-arm64-dts-broadcom-bcm4908-add-Asus-GT-AC5300-LEDs.patch bcm4908/patches-5.15/034-v6.1-0004-arm64-dts-bcmbca-update-BCM4908-board-dts-files.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod 01. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=77112d23a671697f0f70695ab901f807e15d2093 02. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe07b3b5af01f42b291f5da0da09d047f50b33a6 03. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=273be36e420924237f6c9d43cdad96718c13dd52 04. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe8ab85ed4958e58e991bba0aa0a655b552b0273 05. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6ae67829fa5e9e71f458f69db42f0e216225616a 06. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=1994284cb9226b65ca3a6744ce3320218b584f26 07. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=a46878476c5549a4fde15a31922ce80a50b23492 08. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=112ff0f2530549d50510f116474924f9c4fad590 09. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=7c253e98685e6d884d12e2618ef4d2ad90b4fbd7 10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=8444b46e163aa9559a0af0381a1d230ec4146eb2 11. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6d1af517817a760d7af3dee0fc4603645485495c 12. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=cc4f0e168a5630ad0491ac5328f1a89f3cf3d04e Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: remove device tree legacy compatibilityNick Hainke2023-05-122-64/+0
| | | | | | | We switched to 5.15 kernel, so we don't need to maintain 5.10 compatibility anymore. Signed-off-by: Nick Hainke <vincent@systemli.org>
* treewide: cleanup kernel symbol referencesNick Hainke2023-05-124-9/+4
| | | | | | | | | | | | | | | We only use 5.15 kernel. So remove all those unnecessary symbols referencing 5.10 or 5.15 kernel. Can be found with: git grep -E 'LINUX_5_1(0|5)' Note that we remove the dependency from "sound-soc-chipdip-dac" instead of removing the complete kernel package. The 5.15 version bump forgot to delete the "@LINUX_5_10" dependency. The kernel package is still needed in 5.15 kernel. Signed-off-by: Nick Hainke <vincent@systemli.org>
* treewide: remove all @{lt,gt,ge,le} appearances affecting 5.10 kernelNick Hainke2023-05-121-1/+0
| | | | | | We only use 5.15 kernel. So remove all those unnecessary appearances. Signed-off-by: Nick Hainke <vincent@systemli.org>
* treewide: remove files for building 5.10 kernelNick Hainke2023-05-121544-254274/+0
| | | | | | | | | | | All targets are bumped to 5.15. Remove the old 5.10 patches, configs and files using: find target/linux -iname '*-5.10' -exec rm -r {} \; Further, remove the 5.10 include. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath25: switch default kernel to 5.15Nick Hainke2023-05-121-2/+1
| | | | | | | | | | | | Switch to kernel 5.15 although it is marked as source only. It is marked as source only because nobody was able to test this device. Merging this is important to finally branch a new release. We want to get rid completely of 5.10 kernel. Without this commit we get following error: "Missing kernel version/hash file for 5.10." Hopfully someone will fix the board in the rc phase or it will be removed completly. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath25: 5.15: enable 5.15 testing kernelNick Hainke2023-05-1211-46/+61
| | | | | | | | | | | | | | | | | | | | | | | Manually refreshed: - 140-redboot_boardconfig.patch - 141-redboot_partition_scan.patch - 142-redboot_various_erase_size_fix.patch Automatically refreshed: - 107-ar5312_gpio.patch - 108-ar2315_gpio.patch - 110-ar2313_ethernet.patch - 120-spiflash.patch - 130-watchdog.patch - 330-board_leds.patch Use "make kernel_oldconfig" to refresh the new kernel config. The Ubiquiti Nanostation 2 (XS2) and Ubiquiti Nanostation 5 (XS5) should be marked as broken when switching to 5.15 by default. The new kernel does not fit anymore into the partition. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath25: 5:15: copy config and patch from 5.10Nick Hainke2023-05-1213-0/+3843
| | | | | | Copy config and patch from kernel 5.10 to kernel 5.15. Signed-off-by: Nick Hainke <vincent@systemli.org>
* omap: switch default kernel to 5.15Alexey Smirnov2023-05-121-2/+1
| | | | | | | | | | | | | | | | | | | | | | Switch to kernel 5.15 although it is marked as source only. It is marked as source only because the eth0 interface can't be added to the br-lan default interface resulting in a broken ethernet [0]. There is a workaround to set a higher pvd (e.g. to 4000) in the dts [1]. Other functionality was already tested on a Beaglebone Black for +6month now without issues. Merging this is important to finally branch a new release. We want to get rid completely of 5.10 kernel. Without this commit we get following error: "Missing kernel version/hash file for 5.10." Hopfully someone will fix the board in the rc phase. - [0] https://github.com/openwrt/openwrt/issues/11953 - [1] https://github.com/openwrt/openwrt/issues/11953#issuecomment-1419078990 Signed-off-by: Alexey Smirnov <s.alexey@gmail.com> [rewrite commit message] Signed-off-by: Nick Hainke <vincent@systemli.org>
* lantiq: 5.15: fix compilation warning pciex fixup patchChristian Marangi2023-05-121-1/+1
| | | | | | | | | | | | | | | | | pcibios_map_irq request a const pci_dev while pci_find_capability doesn't. Cast dropping the const to fix compilation warning. Fix compilation warning: arch/mips/pci/fixup-lantiq.c: In function 'pcibios_map_irq': arch/mips/pci/fixup-lantiq.c:34:33: error: passing argument 1 of 'pci_find_capability' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] 34 | if (pci_find_capability(dev, PCI_CAP_ID_EXP)) | ^~~ In file included from arch/mips/pci/fixup-lantiq.c:9: ./include/linux/pci.h:1129:40: note: expected 'struct pci_dev *' but argument is of type 'const struct pci_dev *' 1129 | u8 pci_find_capability(struct pci_dev *dev, int cap); | ~~~~~~~~~~~~~~~~^~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* linux/generic/hack-5.15: add missing patch headerFlorian Eckert2023-05-121-47/+65
| | | | | | | This patch does not have a valid patch headers and does not apply on an external git tree with 'git am'. To fix this add the missing header. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* ramips: fix mt7621 kernel compilationDavid Bauer2023-05-122-8/+14
| | | | | | | | | The OF LED configuration patch fails on MT7621, as the necessary headers were only included for the mediatek subtarget with an additional patch. Fixes: 242fe8634eba ("generic: add hack for MT753x LED configuration") Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: rb91x_nand: fix compilation warning for dev_errChristian Marangi2023-05-121-1/+1
| | | | | | | | | | | | | | | | | Fix compilation warning for dev_err in rb91x_nand driver. Fix compilation warning: drivers/mtd/nand/raw/rb91x_nand.c:289:25: note: in expansion of macro 'dev_err' 289 | dev_err(dev, "failed to get gpios: %d\n", | ^~~~~~~ drivers/mtd/nand/raw/rb91x_nand.c:289:61: note: format string is defined here 289 | dev_err(dev, "failed to get gpios: %d\n", | ~^ | | | int | %ld cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* bmips: 5.15: comment unused macronix_nand_block_protection_supportChristian Marangi2023-05-121-0/+154
| | | | | | | | | | | | Comment unused function macronix_nand_block_protection_support since it does cause boot problem Fix compilation error: drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function] 220 | static void macronix_nand_block_protection_support(struct nand_chip *chip) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* bcm63xx: 5.15: comment unused macronix_nand_block_protection_supportChristian Marangi2023-05-121-0/+154
| | | | | | | | | | | | Comment unused macronix_nand_block_protection_support due to workaround needed to fix booting Fix compilation warning: drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function] 220 | static void macronix_nand_block_protection_support(struct nand_chip *chip) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath79: gpio-latch: fix compilation warning for wrong dev_err %Christian Marangi2023-05-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix compilation warning for using %d instead of %ld for gpio-latch in dev_err. Fix compilation warning: In file included from ./include/linux/device.h:15, from ./include/linux/gpio/driver.h:5, from drivers/gpio/gpio-latch.c:13: drivers/gpio/gpio-latch.c: In function 'gpio_latch_probe': drivers/gpio/gpio-latch.c:137:46: error: format '%d' expects argument of type 'int', but argument 4 has type 'long int' [-Werror=format=] 137 | dev_err(dev, "failed to get gpio %d: %d\n", i, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap' 110 | _p_func(dev, fmt, ##__VA_ARGS__); \ | ^~~ ./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt' 144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~ drivers/gpio/gpio-latch.c:137:33: note: in expansion of macro 'dev_err' 137 | dev_err(dev, "failed to get gpio %d: %d\n", i, | ^~~~~~~ drivers/gpio/gpio-latch.c:137:71: note: format string is defined here 137 | dev_err(dev, "failed to get gpio %d: %d\n", i, | ~^ | | | int | %ld cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mvebu: 5.15: fix compilation warning for mangle bootargs patchChristian Marangi2023-05-121-6/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix compilation warning for mangle bootargs patch. Fix compilation warning: arch/arm/boot/compressed/atags_to_fdt.c: In function 'append_rootblock': arch/arm/boot/compressed/atags_to_fdt.c:84:13: error: assignment discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] 84 | ptr = str - 1; | ^ arch/arm/boot/compressed/atags_to_fdt.c: In function 'atags_to_fdt': arch/arm/boot/compressed/atags_to_fdt.c:213:18: error: unused variable 'memsize' [-Werror=unused-variable] 213 | int ret, memsize; | ^~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c:212:13: error: unused variable 'memcount' [-Werror=unused-variable] 212 | int memcount = 0; | ^~~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c:211:16: error: unused variable 'mem_reg_property' [-Werror=unused-variable] 211 | __be32 mem_reg_property[2 * 2 * NR_BANKS]; | ^~~~~~~~~~~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c: At top level: arch/arm/boot/compressed/atags_to_fdt.c:180:13: error: 'hex_str' defined but not used [-Werror=unused-function] 180 | static void hex_str(char *out, uint32_t value) | ^~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c:63:17: error: 'get_cell_size' defined but not used [-Werror=unused-function] 63 | static uint32_t get_cell_size(const void *fdt) | ^~~~~~~~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c:43:12: error: 'setprop_cell' defined but not used [-Werror=unused-function] 43 | static int setprop_cell(void *fdt, const char *node_path, | ^~~~~~~~~~~~ arch/arm/boot/compressed/atags_to_fdt.c:25:12: error: 'setprop' defined but not used [-Werror=unused-function] 25 | static int setprop(void *fdt, const char *node_path, const char *property, | ^~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: 5.15: add patch commenting unused sdhci functionChristian Marangi2023-05-121-0/+108
| | | | | | | | | | | | Add patch commenting unused sdhci function, hopin this will be dropped when the problem is actually found. Fix compilation warning: drivers/mmc/host/sdhci-msm.c:1781:13: error: 'sdhci_msm_set_clock' defined but not used [-Werror=unused-function] 1781 | static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) | ^~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* layerscape: 5.15: fix compilation warning for fsl ppfe driverChristian Marangi2023-05-121-13/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rework some desc dump and dummy pkt function to fix compilation warning. Fix compilation warning: drivers/staging/fsl_ppfe/pfe_hif.c: In function 'send_dummy_pkt_to_hif': drivers/staging/fsl_ppfe/pfe_hif.c:118:19: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast] 118 | ddr_ptr = (void *)((u64)readl(BMU2_BASE_ADDR + BMU_ALLOC_CTRL)); | ^ drivers/staging/fsl_ppfe/pfe_hif.c:122:20: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast] 122 | lmem_ptr = (void *)((u64)readl(BMU1_BASE_ADDR + BMU_ALLOC_CTRL)); | ^ drivers/staging/fsl_ppfe/pfe_hif.c: In function 'pfe_hif_desc_dump': drivers/staging/fsl_ppfe/pfe_hif.c:195:24: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v + | ^ drivers/staging/fsl_ppfe/pfe_hif.c:195:36: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v + | ^ drivers/staging/fsl_ppfe/pfe_hif.c:207:19: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v + | ^ drivers/staging/fsl_ppfe/pfe_hif.c:207:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v + | ^ cc1: all warnings being treated as errors In file included from ./include/linux/kernel.h:19, from ./include/linux/list.h:9, from ./include/linux/wait.h:7, from ./include/linux/eventfd.h:13, from drivers/staging/fsl_ppfe/pfe_cdev.c:11: drivers/staging/fsl_ppfe/pfe_cdev.c: In function 'pfe_cdev_read': ./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'int' [-Werror=format=] 5 | #define KERN_SOH "\001" /* ASCII Start Of Header */ | ^~~~~~ ./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap' 422 | _p_func(_fmt, ##__VA_ARGS__); \ | ^~~~ ./include/linux/printk.h:132:17: note: in expansion of macro 'printk' 132 | printk(fmt, ##__VA_ARGS__); \ | ^~~~~~ ./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk' 580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~ ./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH' 15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */ | ^~~~~~~~ ./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG' 580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~~ drivers/staging/fsl_ppfe/pfe_cdev.c:42:17: note: in expansion of macro 'pr_debug' 42 | pr_debug("%u %lu", link_states[ret].phy_id, | ^~~~~~~~ ./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'size_t' {aka 'unsigned int'} [-Werror=format=] 5 | #define KERN_SOH "\001" /* ASCII Start Of Header */ | ^~~~~~ ./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap' 422 | _p_func(_fmt, ##__VA_ARGS__); \ | ^~~~ ./include/linux/printk.h:493:9: note: in expansion of macro 'printk' 493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~ ./include/linux/kern_levels.h:11:25: note: in expansion of macro 'KERN_SOH' 11 | #define KERN_ERR KERN_SOH "3" /* error conditions */ | ^~~~~~~~ ./include/linux/printk.h:493:16: note: in expansion of macro 'KERN_ERR' 493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~ drivers/staging/fsl_ppfe/pfe_cdev.c:50:17: note: in expansion of macro 'pr_err' 50 | pr_err("Failed to send (%d)bytes of (%lu) requested.\n", | ^~~~~~ ./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 2 has type 'unsigned int' [-Werror=format=] 5 | #define KERN_SOH "\001" /* ASCII Start Of Header */ | ^~~~~~ ./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap' 422 | _p_func(_fmt, ##__VA_ARGS__); \ | ^~~~ ./include/linux/printk.h:132:17: note: in expansion of macro 'printk' 132 | printk(fmt, ##__VA_ARGS__); \ | ^~~~~~ ./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk' 580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~ ./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH' 15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */ | ^~~~~~~~ ./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG' 580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~~ drivers/staging/fsl_ppfe/pfe_cdev.c:57:9: note: in expansion of macro 'pr_debug' 57 | pr_debug("Read of (%lu) bytes performed.\n", sizeof(link_states)); | ^~~~~~~~ cc1: all warnings being treated as errors In file included from ./include/uapi/linux/posix_types.h:5, from ./include/uapi/linux/types.h:14, from ./include/linux/types.h:6, from ./include/linux/list.h:5, from ./include/linux/module.h:12, from drivers/staging/fsl_ppfe/pfe_sysfs.c:7: drivers/staging/fsl_ppfe/pfe_sysfs.c: In function 'pfe_set_util': ./include/linux/stddef.h:8:14: error: passing argument 2 of 'kstrtoul' makes integer from pointer without a cast [-Werror=int-conversion] 8 | #define NULL ((void *)0) | ^~~~~~~~~~~ | | | void * drivers/staging/fsl_ppfe/pfe_sysfs.c:538:39: note: in expansion of macro 'NULL' 538 | util_do_clear = kstrtoul(buf, NULL, 0); | ^~~~ In file included from ./include/linux/kernel.h:13, from ./include/linux/list.h:9: ./include/linux/kstrtox.h:30:69: note: expected 'unsigned int' but argument is of type 'void *' 30 | static inline int __must_check kstrtoul(const char *s, unsigned int base, unsigned long *res) | ~~~~~~~~~~~~~^~~~ cc1: all warnings being treated as errors With UTIL compiled on, fix compilation warning: drivers/staging/fsl_ppfe/pfe_hal.c: In function 'pe_load_ddr_section': drivers/staging/fsl_ppfe/pfe_hal.c:617:19: error: 'else' without a previous 'if' 617 | } else { | ^~~~ drivers/staging/fsl_ppfe/pfe_hal.c:622:17: error: break statement not within loop or switch 622 | break; | ^~~~~ drivers/staging/fsl_ppfe/pfe_hal.c:624:9: error: case label not within a switch statement 624 | case SHT_NOBITS: | ^~~~ drivers/staging/fsl_ppfe/pfe_hal.c:627:17: error: break statement not within loop or switch 627 | break; | ^~~~~ drivers/staging/fsl_ppfe/pfe_hal.c:629:9: error: 'default' label not within a switch statement 629 | default: | ^~~~~~~ drivers/staging/fsl_ppfe/pfe_hal.c: At top level: drivers/staging/fsl_ppfe/pfe_hal.c:635:9: error: expected identifier or '(' before 'return' 635 | return 0; | ^~~~~~ drivers/staging/fsl_ppfe/pfe_hal.c:636:1: error: expected identifier or '(' before '}' token 636 | } Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* layerscape: 5.15: fix compilation warning for PHY_INTERFACE_MODE_2500SGMIIChristian Marangi2023-05-121-0/+21
| | | | | | | | | | | | Fix compilation warning for PHY_INTERFACE_MODE_2500SGMII patch. Fix compilation warning: drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes': drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch] 360 | switch (interface) { | ^~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq806x: 5.15: drop arm override compile patchChristian Marangi2023-05-121-21/+0
| | | | | | | | | | | | | | | | | Drop arm override compile patch. The use is dubious and at times (2016) it was never explained why this was required. Krait CPU and Cortex-a15 may be similar but they have some intrinsic difference. While very similar they differ a lot in additional feature and also cache configuration. Also these conflict with raid6 libraty compilation that use specific workaround not compatible with cortex-a15 and produce compilation warning. Fix compilation warning: cc1: error: switch '-mcpu=cortex-a15' conflicts with switch '-march=armv7-a+simd' [-Werror] cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: 5.15: replace fallthrough comment for rtl838x ethernet driverChristian Marangi2023-05-121-1/+1
| | | | | | | | | | | | | | Replace fallthrough comment with fallthrough macro for rtl838x ethernet driver. Fix compilarion warning: drivers/net/ethernet/rtl838x_eth.c: In function 'rtl930x_mdio_reset': drivers/net/ethernet/rtl838x_eth.c:1959:43: error: this statement may fall through [-Werror=implicit-fallthrough=] 1959 | private_poll_mask |= BIT(i); drivers/net/ethernet/rtl838x_eth.c:1961:17: note: here 1961 | case PHY_INTERFACE_MODE_USXGMII: | ^~~~ Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: 5.15: fix uninizialized variable in rtl83xx qos driverChristian Marangi2023-05-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | Fix uninizialized variable in rtl83xx qos driver Fix compilation error: drivers/net/dsa/rtl83xx/qos.c: In function 'rtl838x_setup_prio2queue_matrix': drivers/net/dsa/rtl83xx/qos.c:298:19: error: 'v' is used uninitialized [-Werror=uninitialized] 298 | v |= i << (min_queues[i] * 3); | ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/dsa/rtl83xx/qos.c:294:13: note: 'v' was declared here 294 | u32 v; | ^ drivers/net/dsa/rtl83xx/qos.c: In function 'rtl83xx_setup_prio2queue_cpu_matrix': drivers/net/dsa/rtl83xx/qos.c:320:19: error: 'v' is used uninitialized [-Werror=uninitialized] 320 | v |= max_queues[i] << (i * 3); | ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/dsa/rtl83xx/qos.c:316:13: note: 'v' was declared here 316 | u32 v; | ^ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: 5.15: comment unused part of realtek ethernet driverChristian Marangi2023-05-127-253/+263
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Comment unused part of realtek phy driver. Fix compilation warning: drivers/net/phy/rtl83xx-phy.c: In function 'rtl8380_configure_int_rtl8218b': drivers/net/phy/rtl83xx-phy.c:747:21: error: unused variable 'ipd_flag' [-Werror=unused-variable] 747 | int ipd_flag = 1; | ^~~~~~~~ drivers/net/phy/rtl83xx-phy.c: At top level: drivers/net/phy/rtl83xx-phy.c:3333:13: error: 'rtl931x_sds_disable' defined but not used [-Werror=unused-function] 3333 | static void rtl931x_sds_disable(u32 sds) | ^~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Comment unused part of realtek dsa driver. Fix compilation warning: drivers/net/dsa/rtl83xx/common.c: In function 'rtl83xx_fib_event': drivers/net/dsa/rtl83xx/common.c:1430:58: error: unused variable 'fen6_info' [-Werror=unused-variable] 1430 | struct fib6_entry_notifier_info *fen6_info = ptr; | ^~~~~~~~~ drivers/net/dsa/rtl83xx/common.c: At top level: drivers/net/dsa/rtl83xx/common.c:531:12: error: 'rtl83xx_octet_cntr_alloc' defined but not used [-Werror=unused-function] 531 | static int rtl83xx_octet_cntr_alloc(struct rtl838x_switch_priv *priv) | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Drop unused priv in realtek dsa driver. Fix compilation warning: drivers/net/dsa/rtl83xx/dsa.c: In function 'rtl83xx_port_lag_change': drivers/net/dsa/rtl83xx/dsa.c:2016:37: error: unused variable 'priv' [-Werror=unused-variable] 2016 | struct rtl838x_switch_priv *priv = ds->priv; | ^~~~ cc1: all warnings being treated as errors Comment rtl838x_pie_rule_dump in realtek dsa driver for rtl83xx Fix compilation warning: drivers/net/dsa/rtl83xx/rtl838x.c:1294:13: error: 'rtl838x_pie_rule_dump' defined but not used [-Werror=unused-function] 1294 | static void rtl838x_pie_rule_dump(struct pie_rule *pr) | ^~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Comment multiple function in realtek dsa driver for rtl930x Fix compilation warning: drivers/net/dsa/rtl83xx/rtl930x.c:1463:12: error: 'rtl930x_l3_intf_add' defined but not used [-Werror=unused-function] 1463 | static int rtl930x_l3_intf_add(struct rtl838x_switch_priv *priv, struct rtl838x_l3_intf *intf) | ^~~~~~~~~~~~~~~~~~~ drivers/net/dsa/rtl83xx/rtl930x.c:1414:12: error: 'rtl930x_l3_mtu_del' defined but not used [-Werror=unused-function] 1414 | static int rtl930x_l3_mtu_del(struct rtl838x_switch_priv *priv, int mtu) | ^~~~~~~~~~~~~~~~~~ drivers/net/dsa/rtl83xx/rtl930x.c:995:12: error: 'rtl930x_l3_hash6' defined but not used [-Werror=unused-function] 995 | static u32 rtl930x_l3_hash6(struct in6_addr *ip6, int algorithm, bool move_dip) | ^~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors drivers/net/dsa/rtl83xx/rtl930x.c:1690:13: error: 'rtl930x_read_pie_fixed_fields' defined but not used [-Werror=unused-function] 1690 | static void rtl930x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/dsa/rtl83xx/rtl930x.c:1432:12: error: 'rtl930x_l3_mtu_add' defined but not used [-Werror=unused-function] 1432 | static int rtl930x_l3_mtu_add(struct rtl838x_switch_priv *priv, int mtu) | ^~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Comment rtl931x_read_pie_fixed_fields in realtek dsa driver for rtl931x Fix compilation warning: drivers/net/dsa/rtl83xx/rtl931x.c:1116:13: error: 'rtl931x_read_pie_fixed_fields' defined but not used [-Werror=unused-function] 1116 | static void rtl931x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Comment rtl93xx_header_vlan_set in realtek ethernet driver for rtl838x Fix compilation warning: drivers/net/ethernet/rtl838x_eth.c: At top level: drivers/net/ethernet/rtl838x_eth.c:164:13: error: 'rtl93xx_header_vlan_set' defined but not used [-Werror=unused-function] 164 | static void rtl93xx_header_vlan_set(struct p_hdr *h, int vlan) | ^~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: 5.15: fix warning for i2c_mii_valid_phy_id and i2c_mii_phy_addrChristian Marangi2023-05-121-35/+15
| | | | | | | | | | | | | | | | Rework exposing i2c_mii_valid_phy_id and i2c_mii_phy_addr in global include. Fix compilation warning: In file included from drivers/net/phy/sfp.c:11: ./include/linux/mdio/mdio-i2c.h:27:21: error: 'i2c_mii_phy_addr' defined but not used [-Werror=unused-function] 27 | static unsigned int i2c_mii_phy_addr(int phy_id) | ^~~~~~~~~~~~~~~~ ./include/linux/mdio/mdio-i2c.h:22:13: error: 'i2c_mii_valid_phy_id' defined but not used [-Werror=unused-function] 22 | static bool i2c_mii_valid_phy_id(int phy_id) | ^~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: 5.15: fix compilation warning with PHY_INTERFACE_MODE_HSGMIIChristian Marangi2023-05-121-1/+20
| | | | | | | | | | | | | PHY_INTERFACE_MODE_HSGMII was not handled in phylink_get_linkmodes and phylink_parse_mode. Fix compilation warning by adding it in the enum: drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes': drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_HSGMII' not handled in switch [-Werror=switch] 360 | switch (interface) { | ^~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: 5.15: add patch fixing compilation warning for hsdma-mt7621Christian Marangi2023-05-121-0/+31
| | | | | | | | | | | Add patch fixing compilation warning for hsdma-mt7621: drivers/staging/mt7621-dma/hsdma-mt7621.c: In function 'mtk_hsdma_probe': drivers/staging/mt7621-dma/hsdma-mt7621.c:685:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 685 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: rt3833: fix compilation warning from device_reset in fe_probeChristian Marangi2023-05-121-1/+3
| | | | | | | | | | | | | Fix compilation warning from device_reset in fe_probe. On fail print a warning but don't fail probe. Fix compilation warning: drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe': drivers/net/ethernet/ralink/mtk_eth_soc.c:1564:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 1564 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: mt76x8: fix compilation warning in esw driverChristian Marangi2023-05-121-2/+1
| | | | | | | | | | | | | | | | | | | | | | | Fix compilation warning for debug string in esw driver: drivers/net/ethernet/ralink/esw_rt3050.c:1535:9: note: in expansion of macro 'dev_info' 1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n", | ^~~~~~~~ drivers/net/ethernet/ralink/esw_rt3050.c:1535:53: note: format string is defined here 1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n", | ~~~~^ | | | long unsigned int | %08p cc1: all warnings being treated as errors Fix unused variable causing compilation warning: drivers/net/ethernet/ralink/esw_rt3050.c: In function 'esw_interrupt': drivers/net/ethernet/ralink/esw_rt3050.c:769:13: error: unused variable 'i' [-Werror=unused-variable] 769 | int i; | ^ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mtk-mcc: move cmd_buf for dbg under ifdefChristian Marangi2023-05-121-2/+3
| | | | | | | | | | Move cmd_buf for dbg under ifdef to fix compilation warning: drivers/mmc/host/mtk-mmc/dbg.c:51:13: error: 'cmd_buf' defined but not used [-Werror=unused-variable] 51 | static char cmd_buf[256]; | ^~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: mt7620: fix compilation warning for device_reset in i2s driverChristian Marangi2023-05-121-2/+6
| | | | | | | | | | | | | Fix compilation warning for device_reset in i2s driver. Fix compilation warning: sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe': sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 885 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errorralink: mt7620: fix compilation warning for device_reset in i2s driver Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 14:04:42 +0000