From 14d4e308e0aa0b78dc7a059716861a4380de3535 Mon Sep 17 00:00:00 2001 From: Aleksander Jan Bajkowski Date: Tue, 14 Sep 2021 23:21:02 +0200 Subject: [PATCH 5/5] net: lantiq: configure the burst length in ethernet drivers Configure the burst length in Ethernet drivers. This improves Ethernet performance by 58%. According to the vendor BSP, 8W burst length is supported by ar9 and newer SoCs. The NAT benchmark results on xRX200 (Down/Up): * 2W: 330 Mb/s * 4W: 432 Mb/s 372 Mb/s * 8W: 520 Mb/s 389 Mb/s Tested on xRX200 and xRX330. Signed-off-by: Aleksander Jan Bajkowski Signed-off-by: David S. Miller --- drivers/net/ethernet/lantiq_etop.c | 21 ++++++++++++++++++--- drivers/net/ethernet/lantiq_xrx200.c | 21 ++++++++++++++++++--- 2 files changed, 36 insertions(+), 6 deletions(-) --- a/drivers/net/ethernet/lantiq_etop.c +++ b/drivers/net/ethernet/lantiq_etop.c @@ -148,6 +148,9 @@ struct ltq_etop_priv { struct ltq_etop_chan txch; struct ltq_etop_chan rxch; + int tx_burst_len; + int rx_burst_len; + int tx_irq; int rx_irq; @@ -399,7 +402,7 @@ ltq_etop_dma_init(struct net_device *dev int rx = priv->rx_irq - LTQ_DMA_ETOP; int err; - ltq_dma_init_port(DMA_PORT_ETOP); + ltq_dma_init_port(DMA_PORT_ETOP, priv->tx_burst_len, rx_burst_len); priv->txch.dma.nr = tx; priv->txch.dma.dev = &priv->pdev->dev; @@ -676,8 +679,8 @@ ltq_etop_tx(struct sk_buff *skb, struct return NETDEV_TX_BUSY; } - /* dma needs to start on a 16 byte aligned address */ - byte_offset = CPHYSADDR(skb->data) % 16; + /* dma needs to start on a burst length value aligned address */ + byte_offset = CPHYSADDR(skb->data) % (priv->tx_burst_len * 4); priv->txch.skb[priv->txch.dma.desc] = skb; netif_trans_update(dev); @@ -925,6 +928,18 @@ static int ltq_etop_probe(struct platfor spin_lock_init(&priv->lock); SET_NETDEV_DEV(dev, &pdev->dev); + err = device_property_read_u32(&pdev->dev, "lantiq,tx-burst-length", &priv->tx_burst_len); + if (err < 0) { + dev_err(&pdev->dev, "unable to read tx-burst-length property\n"); + return err; + } + + err = device_property_read_u32(&pdev->dev, "lantiq,rx-burst-length", &priv->rx_burst_len); + if (err < 0) { + dev_err(&pdev->dev, "unable to read rx-burst-length property\n"); + return err; + } + netif_napi_add(dev, &priv->txch.napi, ltq_etop_poll_tx, 8); netif_napi_add(dev, &priv->rxch.napi, ltq_etop_poll_rx, 32); priv->txch.netdev = dev; --- a/drivers/net/ethernet/lantiq_xrx200.c +++ b/drivers/net/ethernet/lantiq_xrx200.c @@ -81,6 +81,9 @@ struct xrx200_priv { struct net_device *net_dev; struct device *dev; + int tx_burst_len; + int rx_burst_len; + __iomem void *pmac_reg; }; @@ -363,8 +366,8 @@ static netdev_tx_t xrx200_start_xmit(str if (unlikely(dma_mapping_error(priv->dev, mapping))) goto err_drop; - /* dma needs to start on a 16 byte aligned address */ - byte_offset = mapping % 16; + /* dma needs to start on a burst length value aligned address */ + byte_offset = mapping % (priv->tx_burst_len * 4); desc->addr = mapping - byte_offset; /* Make sure the address is written before we give it to HW */ @@ -465,7 +468,7 @@ static int xrx200_dma_init(struct xrx200 int ret = 0; int i; - ltq_dma_init_port(DMA_PORT_ETOP); + ltq_dma_init_port(DMA_PORT_ETOP, priv->tx_burst_len, rx_burst_len); ch_rx->dma.nr = XRX200_DMA_RX; ch_rx->dma.dev = priv->dev; @@ -575,6 +578,18 @@ static int xrx200_probe(struct platform_ if (err) eth_hw_addr_random(net_dev); + err = device_property_read_u32(dev, "lantiq,tx-burst-length", &priv->tx_burst_len); + if (err < 0) { + dev_err(dev, "unable to read tx-burst-length property\n"); + return err; + } + + err = device_property_read_u32(dev, "lantiq,rx-burst-length", &priv->rx_burst_len); + if (err < 0) { + dev_err(dev, "unable to read rx-burst-length property\n"); + return err; + } + /* bring up the dma engine and IP core */ err = xrx200_dma_init(priv); if (err)