amd/geode_lx: Remove most boards

There is active work to convert remaining two boards,
PC Engines alix1c and alix2d, to EARLY_CBMEM_INIT.

Change-Id: I87e3963af7ef719e9fa2a8b0df34a896265905f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>

28 files changed, 0 insertions, 1814 deletions

diff --git a/src/mainboard/lippert/hurricane-lx/Kconfig b/src/mainboard/lippert/hurricane-lx/Kconfig
deleted file mode 100644
index 04c22201c614..000000000000
--- a/src/mainboard/lippert/hurricane-lx/Kconfig
+++ /dev/null
@@ -1,56 +0,0 @@
-if BOARD_LIPPERT_HURRICANE_LX
-
-config BOARD_SPECIFIC_OPTIONS # dummy
-	def_bool y
-	select CPU_AMD_GEODE_LX
-	select NORTHBRIDGE_AMD_LX
-	select SOUTHBRIDGE_AMD_CS5536
-	select SUPERIO_ITE_IT8712F
-	select HAVE_PIRQ_TABLE
-	select PIRQ_ROUTE
-	select UDELAY_TSC
-	# Board is equipped with a 1 MB SPI flash, however, due to limitations
-	# of the IT8712F Super I/O, only the top 512 KB are directly mapped.
-	select BOARD_ROMSIZE_KB_512
-	select PLL_MANUAL_CONFIG
-	select CORE_GLIU_500_333
-	select POWER_BUTTON_FORCE_ENABLE if !BOARD_OLD_REVISION
-
-config MAINBOARD_DIR
-	string
-	default lippert/hurricane-lx
-
-config MAINBOARD_PART_NUMBER
-	string
-	default "Hurricane-LX"
-
-config IRQ_SLOT_COUNT
-	int
-	default 8
-
-config BOARD_OLD_REVISION
-	bool "Board is old pre-3.0 revision"
-	default n
-	select POWER_BUTTON_DEFAULT_DISABLE
-	help
-	  Look on the bottom side for a number like 406-0001-30.  The last 2
-	  digits state the PCB revision (3.0 in this example).  For 2.0 or older
-	  boards choose Y, for 3.0 and newer say N.
-
-	  Old revision boards need a jumper shorting the power button to
-	  power on automatically.  You may enable the button only after this
-	  jumper has been removed.  New revision boards are not restricted
-	  in this way, and always have the power button enabled.
-
-config ONBOARD_UARTS_RS485
-	bool "Switch on-board serial ports to RS485"
-	default n
-	help
-	  If selected, both on-board serial ports will operate in RS485 mode
-	  instead of RS232.
-
-config PLLMSRlo
-	hex
-	default 0x00de6001
-
-endif # BOARD_LIPPERT_HURRICANE_LX
diff --git a/src/mainboard/lippert/hurricane-lx/Kconfig.name b/src/mainboard/lippert/hurricane-lx/Kconfig.name
deleted file mode 100644
index 810fd4488330..000000000000
--- a/src/mainboard/lippert/hurricane-lx/Kconfig.name
+++ /dev/null
@@ -1,2 +0,0 @@
-config BOARD_LIPPERT_HURRICANE_LX
-	bool "Hurricane-LX"
diff --git a/src/mainboard/lippert/hurricane-lx/board_info.txt b/src/mainboard/lippert/hurricane-lx/board_info.txt
deleted file mode 100644
index b464c8528cec..000000000000
--- a/src/mainboard/lippert/hurricane-lx/board_info.txt
+++ /dev/null
@@ -1,6 +0,0 @@
-Category: half
-Board URL: http://www.adlinktech.com/PD/web/PD_detail.php?pid=1154
-ROM package: SOIC8
-ROM protocol: SPI
-ROM socketed: n
-Flashrom support: n
diff --git a/src/mainboard/lippert/hurricane-lx/devicetree.cb b/src/mainboard/lippert/hurricane-lx/devicetree.cb
deleted file mode 100644
index 7f751eb45408..000000000000
--- a/src/mainboard/lippert/hurricane-lx/devicetree.cb
+++ /dev/null
@@ -1,90 +0,0 @@
-chip northbridge/amd/lx
-	device domain 0 on
-		device pci 1.0 on end				# Northbridge
-		device pci 1.1 on end				# Graphics
-		device pci 1.2 on end				# AES
-		chip southbridge/amd/cs5536
-			# IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK
-			# SIRQ Mode = Active(Quiet) mode. Save power....
-			# Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse,
-			# UARTs, etc IRQs. OK
-			register "lpc_serirq_enable"			= "0x000012DA" # 00010010 11011010
-			register "lpc_serirq_polarity"			= "0x0000ED25" # inverse of above
-			register "lpc_serirq_mode"			= "1"
-			register "enable_gpio_int_route"		= "0x0D0C0700"
-			register "enable_ide_nand_flash"		= "0" # 0:ide mode, 1:flash
-			register "enable_USBP4_device"			= "0" # 0:host, 1:device
-			register "enable_USBP4_overcurrent"		= "0" # 0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
-			register "com1_enable"				= "0"
-			register "com1_address"				= "0x3E8"
-			register "com1_irq"				= "6"
-			register "com2_enable"				= "0"
-			register "com2_address"				= "0x2E8"
-			register "com2_irq"				= "6"
-			register "unwanted_vpci[0]"			= "0" # End of list has a zero
-			device pci 8.0 on end		# Slot4
-			device pci 9.0 on end		# Slot3
-			device pci a.0 on end		# Slot2
-			device pci b.0 on end		# Slot1
-			device pci c.0 on end		# IT8888
-			device pci d.0 on end		# Mini-PCI
-			device pci e.0 on end		# Ethernet
-			device pci f.0 on			# ISA Bridge
-				chip superio/ite/it8712f
-					device pnp 2e.0 on		# Floppy
-						io 0x60 = 0x3f0
-						irq 0x70 = 6
-						drq 0x74 = 2
-					end
-					device pnp 2e.1 on		# Com1
-						io 0x60 = 0x3f8
-						irq 0x70 = 4
-					end
-					device pnp 2e.2 on		# Com2
-						io 0x60 = 0x2f8
-						irq 0x70 = 3
-					end
-					device pnp 2e.3 on		# Parallel port
-						io 0x60 = 0x378
-						irq 0x70 = 7
-					end
-					device pnp 2e.4 on		# EC
-						io 0x60 = 0x290 # EC
-						io 0x62 = 0x298 # PME
-						irq 0x70 = 9
-					end
-					device pnp 2e.5 on		# PS/2 keyboard
-						io 0x60 = 0x60
-						io 0x62 = 0x64
-						irq 0x70 = 1
-					end
-					device pnp 2e.6 on		# PS/2 mouse
-						irq 0x70 = 12
-					end
-					device pnp 2e.7 on		# GPIO
-						io 0x62 = 0x1220 # Simple I/O
-						io 0x64 = 0x1228 # SPI
-					end
-					device pnp 2e.8 off		# MIDI
-						io 0x60 = 0x300
-						irq 0x70 = 9
-					end
-					device pnp 2e.9 off		# Game port
-						io 0x60 = 0x220
-					end
-					device pnp 2e.a off end	# CIR
-				end
-			end
-			device pci f.2 on end		# IDE
-			device pci f.3 on end		# Audio
-			device pci f.4 on end		# OHCI
-			device pci f.5 on end		# EHCI
-		end
-	end
-	# APIC cluster is late CPU init.
-	device cpu_cluster 0 on
-		chip cpu/amd/geode_lx
-			device lapic 0 on end
-		end
-	end
-end
diff --git a/src/mainboard/lippert/hurricane-lx/irq_tables.c b/src/mainboard/lippert/hurricane-lx/irq_tables.c
deleted file mode 100644
index 8d09cf450c5f..000000000000
--- a/src/mainboard/lippert/hurricane-lx/irq_tables.c
+++ /dev/null
@@ -1,72 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on irq_tables.c from the SpaceRunner-LX mainboard. */
-
-#include <arch/pirq_routing.h>
-#include <console/console.h>
-#include <arch/io.h>
-#include <arch/pirq_routing.h>
-#include "southbridge/amd/cs5536/cs5536.h"
-
-/* Platform IRQs */
-#define PIRQA 10
-#define PIRQB 11
-#define PIRQC 5
-#define PIRQD 15
-
-/* Map */
-#define M_PIRQA (1 << PIRQA)	/* Bitmap of supported IRQs */
-#define M_PIRQB (1 << PIRQB)	/* Bitmap of supported IRQs */
-#define M_PIRQC (1 << PIRQC)	/* Bitmap of supported IRQs */
-#define M_PIRQD (1 << PIRQD)	/* Bitmap of supported IRQs */
-
-/* Link */
-#define L_PIRQA	 1		/* Means Slot INTx# Connects To Chipset INTA# */
-#define L_PIRQB	 2		/* Means Slot INTx# Connects To Chipset INTB# */
-#define L_PIRQC	 3		/* Means Slot INTx# Connects To Chipset INTC# */
-#define L_PIRQD	 4		/* Means Slot INTx# Connects To Chipset INTD# */
-
-static const struct irq_routing_table intel_irq_routing_table = {
-	PIRQ_SIGNATURE,		/* u32 signature */
-	PIRQ_VERSION,		/* u16 version   */
-	32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* There can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
-	0x00,			/* Where the interrupt router lies (bus) */
-	(0x0F << 3) | 0x0,	/* Where the interrupt router lies (dev) */
-	0x00,			/* IRQs devoted exclusively to PCI usage */
-	0x100B,			/* Vendor */
-	0x002B,			/* Device */
-	0,			/* Miniport data */
-	{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},	/* u8 rfu[11] */
-	0x36,			/* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
-	{
-		/* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
-		/* bus, dev|fn,           {link, bitmap},      {link, bitmap},     {link, bitmap},     {link, bitmap},     slot, rfu */
-		{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* CPU */
-		{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0},	/* chipset */
-		{0x00, (0x0E << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* ethernet */
-		{0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0},	/* slot1 */
-		{0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0},	/* slot2 */
-		{0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0},	/* slot3 */
-		{0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0},	/* slot4 */
-		{0x00, (0x0D << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00}},       0x5, 0x0},	/* Mini-PCI */
-	}
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
-	return copy_pirq_routing_table(addr, &intel_irq_routing_table);
-}
diff --git a/src/mainboard/lippert/hurricane-lx/mainboard.c b/src/mainboard/lippert/hurricane-lx/mainboard.c
deleted file mode 100644
index 0f210cb200a0..000000000000
--- a/src/mainboard/lippert/hurricane-lx/mainboard.c
+++ /dev/null
@@ -1,83 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on mainboard.c from the SpaceRunner-LX mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <console/console.h>
-#include <device/device.h>
-#include <arch/io.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-
-/* Bit1 switches Com1 to RS485, bit2 same for Com2. */
-#if IS_ENABLED(CONFIG_ONBOARD_UARTS_RS485)
-	#define SIO_GP1X_CONFIG 0x06
-#else
-	#define SIO_GP1X_CONFIG 0x00
-#endif
-
-static const u16 ec_init_table[] = { /* hi = data, lo = index */
-	0x1900,		/* Enable monitoring */
-	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
-	0x805C,		/* Unlock zero adjust */
-	0x7056, 0x3C57,	/* Zero adjust TMPIN1,2 */
-	0x005C,		/* Lock zero adjust */
-	0xD014		/* Also set FAN_CTL polarity to Active High */
-};
-
-static void init(struct device *dev)
-{
-	unsigned int gpio_base, i;
-	printk(BIOS_DEBUG, "LiPPERT Hurricane-LX ENTER %s\n", __func__);
-
-	/* Init CS5536 GPIOs */
-	gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD,
-		    PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
-
-	outl(0x00000040, gpio_base + 0x00); // GPIO6  value      1 - LAN_PD#
-	outl(0x00000040, gpio_base + 0x08); // GPIO6  open drain 1 - LAN_PD# (jumpered GPIO per default)
-	outl(0x00000040, gpio_base + 0x04); // GPIO6  output     1 - LAN_PD#
-	outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1    1 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x20); // GPIO10 input      1 - THRM_ALRM#
-#if !IS_ENABLED(CONFIG_BOARD_OLD_REVISION)
-	outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2   1 - 32kHz
-	outl(0x00000800, gpio_base + 0x84); // GPIO27 output     1 - 32kHz
-#endif
-	outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up    0 - 32kHz (new) / PM-LED (old)
-
-	/* Init Environment Controller. */
-	for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) {
-		u16 val = ec_init_table[i];
-		outb((u8)val, 0x0295);
-		outb(val >> 8, 0x0296);
-	}
-
-	/* bit2 = RS485_EN2, bit1 = RS485_EN1 */
-	outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
-
-	printk(BIOS_DEBUG, "LiPPERT Hurricane-LX EXIT %s\n", __func__);
-}
-
-static void mainboard_enable(struct device *dev)
-{
-	dev->ops->init = init;
-}
-
-struct chip_operations mainboard_ops = {
-	.enable_dev = mainboard_enable,
-};
diff --git a/src/mainboard/lippert/hurricane-lx/romstage.c b/src/mainboard/lippert/hurricane-lx/romstage.c
deleted file mode 100644
index 4e4004bb16e6..000000000000
--- a/src/mainboard/lippert/hurricane-lx/romstage.c
+++ /dev/null
@@ -1,144 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2007 Advanced Micro Devices, Inc.
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on romstage.c from the SpaceRunner-LX mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <console/console.h>
-#include <cpu/x86/bist.h>
-#include <cpu/x86/msr.h>
-#include <cpu/amd/lxdef.h>
-#include <southbridge/amd/cs5536/cs5536.h>
-#include <southbridge/amd/cs5536/smbus.h>
-#include <spd.h>
-#include <superio/ite/common/ite.h>
-#include <superio/ite/it8712f/it8712f.h>
-#include <northbridge/amd/lx/raminit.h>
-
-#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1)
-#define GPIO_DEV PNP_DEV(0x2e, IT8712F_GPIO)
-
-/* Bit0 enables Spread Spectrum. */
-#define SMC_CONFIG	0x01
-
-int spd_read_byte(unsigned int device, unsigned int address)
-{
-	if (device != DIMM0)
-		return 0xFF;	/* No DIMM1, don't even try. */
-
-	return smbus_read_byte(device, address);
-}
-
-#if !IS_ENABLED(CONFIG_BOARD_OLD_REVISION)
-/* Send config data to System Management Controller via SMB. */
-static int smc_send_config(unsigned char config_data)
-{
-	if (smbus_check_stop_condition(SMBUS_IO_BASE))
-		return 1;
-	if (smbus_start_condition(SMBUS_IO_BASE))
-		return 2;
-	if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address
-		return 3;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data
-		return 4;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length
-		return 5;
-	if (smbus_send_command(SMBUS_IO_BASE, config_data))
-		return 6;
-	smbus_stop_condition(SMBUS_IO_BASE);
-	return 0;
-}
-#endif
-
-#include "northbridge/amd/lx/pll_reset.c"
-#include "cpu/amd/geode_lx/cpureginit.c"
-#include "cpu/amd/geode_lx/syspreinit.c"
-#include "cpu/amd/geode_lx/msrinit.c"
-
-static const u16 sio_init_table[] = { // hi = data, lo = index
-	0x042C,		// disable ATXPG; VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 enabled
-	0x1423,		// don't delay PoWeROK1/2
-	0x9072,		// watchdog triggers PWROK, counts seconds
-#if !IS_ENABLED(CONFIG_USE_WATCHDOG_ON_BOOT)
-	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
-#endif
-	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xBF27, 0xFF28, 0x2D29,	// (GP36 = FAN_CTL3 (PWM), GP23,22,16,15 = SPI, GP13 = PWROK1)
-	0x66B8, 0x0CB9,	// enable pullups on SPI, RS485_EN
-	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, WD_ACTIVE
-	0x06C8,		// config GP12,11 as output, GP10 as input
-	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-#if IS_ENABLED(CONFIG_BOARD_OLD_REVISION)
-	0x1F2A, 0xC072,	// switch GP13 to GPIO, WDT output from PWROK to KRST
-#endif
-};
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	int i;
-
-	/* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */
-	for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) {
-		u16 reg = sio_init_table[i];
-		ite_reg_write(GPIO_DEV, (u8) reg, (reg >> 8));
-	}
-}
-
-void asmlinkage mainboard_romstage_entry(unsigned long bist)
-{
-
-	static const struct mem_controller memctrl[] = {
-		{.channel0 = {DIMM0, DIMM1}}
-	};
-
-	SystemPreInit();
-	msr_init();
-
-	cs5536_early_setup();
-
-	/*
-	 * Note: Must do this AFTER the early_setup! It is counting on some
-	 * early MSR setup for CS5536.
-	 */
-	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
-	mb_gpio_init();
-	console_init();
-
-	/* Halt if there was a built in self test failure */
-	report_bist_failure(bist);
-
-	pll_reset();
-
-	cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
-
-#if !IS_ENABLED(CONFIG_BOARD_OLD_REVISION)
-	int err;
-	/* bit0 = Spread Spectrum */
-	if ((err = smc_send_config(SMC_CONFIG))) {
-		printk(BIOS_ERR, "ERROR %d sending config data to SMC\n", err);
-	}
-#endif
-
-	sdram_initialize(1, memctrl);
-
-	/* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
-}
diff --git a/src/mainboard/lippert/literunner-lx/Kconfig b/src/mainboard/lippert/literunner-lx/Kconfig
deleted file mode 100644
index c3aab0e918f3..000000000000
--- a/src/mainboard/lippert/literunner-lx/Kconfig
+++ /dev/null
@@ -1,50 +0,0 @@
-if BOARD_LIPPERT_LITERUNNER_LX
-
-config BOARD_SPECIFIC_OPTIONS # dummy
-	def_bool y
-	select CPU_AMD_GEODE_LX
-	select NORTHBRIDGE_AMD_LX
-	select SOUTHBRIDGE_AMD_CS5536
-	select SUPERIO_ITE_IT8712F
-	select HAVE_DEBUG_SMBUS
-	select HAVE_PIRQ_TABLE
-	select PIRQ_ROUTE
-	select UDELAY_TSC
-	# Board is equipped with a 1 MB SPI flash, however, due to limitations
-	# of the IT8712F Super I/O, only the top 512 KB are directly mapped.
-	select BOARD_ROMSIZE_KB_512
-	select POWER_BUTTON_FORCE_ENABLE
-	select PLL_MANUAL_CONFIG
-	select CORE_GLIU_500_400
-
-config MAINBOARD_DIR
-	string
-	default lippert/literunner-lx
-
-config MAINBOARD_PART_NUMBER
-	string
-	default "Cool LiteRunner-LX"
-
-config IRQ_SLOT_COUNT
-	int
-	default 5
-
-config ONBOARD_UARTS_RS485
-	bool "Switch on-board serial ports 1 & 2 to RS485"
-	default n
-	help
-	  If selected, the first two on-board serial ports will operate in RS485
-	  mode instead of RS232.
-
-config ONBOARD_IDE_SLAVE
-	bool "Make on-board CF socket act as Slave"
-	default n
-	help
-	  If selected, the on-board Compact Flash card socket will act as IDE
-	  Slave instead of Master.
-
-config PLLMSRlo
-	hex
-	default 0x00de6001
-
-endif # BOARD_LIPPERT_LITERUNNER_LX
diff --git a/src/mainboard/lippert/literunner-lx/Kconfig.name b/src/mainboard/lippert/literunner-lx/Kconfig.name
deleted file mode 100644
index 1e44fe472450..000000000000
--- a/src/mainboard/lippert/literunner-lx/Kconfig.name
+++ /dev/null
@@ -1,2 +0,0 @@
-config BOARD_LIPPERT_LITERUNNER_LX
-	bool "Cool LiteRunner-LX"
diff --git a/src/mainboard/lippert/literunner-lx/board_info.txt b/src/mainboard/lippert/literunner-lx/board_info.txt
deleted file mode 100644
index 47b90b5be860..000000000000
--- a/src/mainboard/lippert/literunner-lx/board_info.txt
+++ /dev/null
@@ -1,6 +0,0 @@
-Category: half
-Board URL: http://www.adlinktech.com/PD/web/PD_detail.php?pid=1128
-ROM package: SOIC8
-ROM protocol: SPI
-ROM socketed: n
-Flashrom support: n
diff --git a/src/mainboard/lippert/literunner-lx/devicetree.cb b/src/mainboard/lippert/literunner-lx/devicetree.cb
deleted file mode 100644
index 834f109f6f6a..000000000000
--- a/src/mainboard/lippert/literunner-lx/devicetree.cb
+++ /dev/null
@@ -1,87 +0,0 @@
-chip northbridge/amd/lx
-	device domain 0 on
-		device pci 1.0 on end				# Northbridge
-		device pci 1.1 on end				# Graphics
-		device pci 1.2 on end				# AES
-		chip southbridge/amd/cs5536
-			# IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK
-			# SIRQ Mode = Active(Quiet) mode. Save power....
-			# Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse,
-			# UARTs, etc IRQs. OK
-			register "lpc_serirq_enable"			= "0x0000129A" # 00010010 10011010
-			register "lpc_serirq_polarity"			= "0x0000ED65" # inverse of above
-			register "lpc_serirq_mode"			= "1"
-			register "enable_gpio_int_route"		= "0x0D0C0700"
-			register "enable_ide_nand_flash"		= "0" # 0:ide mode, 1:flash
-			register "enable_USBP4_device"			= "0" # 0:host, 1:device
-			register "enable_USBP4_overcurrent"		= "0" # 0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
-			register "com1_enable"				= "1"
-			register "com1_address"				= "0x3E8"
-			register "com1_irq"				= "6"
-			register "com2_enable"				= "0"
-			register "com2_address"				= "0x2E8"
-			register "com2_irq"				= "6"
-			register "unwanted_vpci[0]"			= "0" # End of list has a zero
-			device pci 8.0 on end		# Ethernet 2
-			device pci c.0 on end		# IT8888
-			device pci d.0 on end		# Mini-PCI
-			device pci e.0 on end		# Ethernet 1
-			device pci f.0 on			# ISA Bridge
-				chip superio/ite/it8712f
-					device pnp 2e.0 off		# Floppy
-						io 0x60 = 0x3f0
-						irq 0x70 = 6
-						drq 0x74 = 2
-					end
-					device pnp 2e.1 on		# Com1
-						io 0x60 = 0x3f8
-						irq 0x70 = 4
-					end
-					device pnp 2e.2 on		# Com2
-						io 0x60 = 0x2f8
-						irq 0x70 = 3
-					end
-					device pnp 2e.3 on		# Parallel port
-						io 0x60 = 0x378
-						irq 0x70 = 7
-					end
-					device pnp 2e.4 on		# EC
-						io 0x60 = 0x290 # EC
-						io 0x62 = 0x298 # PME
-						irq 0x70 = 9
-					end
-					device pnp 2e.5 on		# PS/2 keyboard
-						io 0x60 = 0x60
-						io 0x62 = 0x64
-						irq 0x70 = 1
-					end
-					device pnp 2e.6 on		# PS/2 mouse
-						irq 0x70 = 12
-					end
-					device pnp 2e.7 on		# GPIO
-						io 0x62 = 0x1220 # Simple I/O
-						io 0x64 = 0x1228 # SPI
-					end
-					device pnp 2e.8 off		# MIDI
-						io 0x60 = 0x300
-						irq 0x70 = 9
-					end
-					device pnp 2e.9 off		# Game port
-						io 0x60 = 0x220
-					end
-					device pnp 2e.a off end	# CIR
-				end
-			end
-			device pci f.2 on end		# IDE
-			device pci f.3 on end		# Audio
-			device pci f.4 on end		# OHCI
-			device pci f.5 on end		# EHCI
-		end
-	end
-	# APIC cluster is late CPU init.
-	device cpu_cluster 0 on
-		chip cpu/amd/geode_lx
-			device lapic 0 on end
-		end
-	end
-end
diff --git a/src/mainboard/lippert/literunner-lx/irq_tables.c b/src/mainboard/lippert/literunner-lx/irq_tables.c
deleted file mode 100644
index ede5b1eb8adf..000000000000
--- a/src/mainboard/lippert/literunner-lx/irq_tables.c
+++ /dev/null
@@ -1,69 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on irq_tables.c from the SpaceRunner-LX mainboard. */
-
-#include <arch/pirq_routing.h>
-#include <console/console.h>
-#include <arch/io.h>
-#include <arch/pirq_routing.h>
-#include "southbridge/amd/cs5536/cs5536.h"
-
-/* Platform IRQs */
-#define PIRQA 10
-#define PIRQB 11
-#define PIRQC 5
-#define PIRQD 15
-
-/* Map */
-#define M_PIRQA (1 << PIRQA)	/* Bitmap of supported IRQs */
-#define M_PIRQB (1 << PIRQB)	/* Bitmap of supported IRQs */
-#define M_PIRQC (1 << PIRQC)	/* Bitmap of supported IRQs */
-#define M_PIRQD (1 << PIRQD)	/* Bitmap of supported IRQs */
-
-/* Link */
-#define L_PIRQA	 1		/* Means Slot INTx# Connects To Chipset INTA# */
-#define L_PIRQB	 2		/* Means Slot INTx# Connects To Chipset INTB# */
-#define L_PIRQC	 3		/* Means Slot INTx# Connects To Chipset INTC# */
-#define L_PIRQD	 4		/* Means Slot INTx# Connects To Chipset INTD# */
-
-static const struct irq_routing_table intel_irq_routing_table = {
-	PIRQ_SIGNATURE,		/* u32 signature */
-	PIRQ_VERSION,		/* u16 version   */
-	32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* There can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
-	0x00,			/* Where the interrupt router lies (bus) */
-	(0x0F << 3) | 0x0,	/* Where the interrupt router lies (dev) */
-	0x00,			/* IRQs devoted exclusively to PCI usage */
-	0x100B,			/* Vendor */
-	0x002B,			/* Device */
-	0,			/* Miniport data */
-	{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},	/* u8 rfu[11] */
-	0xB8,			/* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
-	{
-		/* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
-		/* bus, dev|fn,           {link, bitmap},      {link, bitmap},     {link, bitmap},     {link, bitmap},     slot, rfu */
-		{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* CPU */
-		{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0},	/* chipset */
-		{0x00, (0x0E << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* ethernet 1 */
-		{0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* ethernet 2 */
-		{0x00, (0x0D << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00}},       0x1, 0x0},	/* Mini-PCI */
-	}
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
-	return copy_pirq_routing_table(addr, &intel_irq_routing_table);
-}
diff --git a/src/mainboard/lippert/literunner-lx/mainboard.c b/src/mainboard/lippert/literunner-lx/mainboard.c
deleted file mode 100644
index 11f9e1420a8a..000000000000
--- a/src/mainboard/lippert/literunner-lx/mainboard.c
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on mainboard.c from the SpaceRunner-LX mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <console/console.h>
-#include <device/device.h>
-#include <arch/io.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-
-/* Bit0 turns off the Live LED, bit1 switches Com1 to RS485, bit2 same for Com2. */
-#if IS_ENABLED(CONFIG_ONBOARD_UARTS_RS485)
-	#define SIO_GP1X_CONFIG 0x07
-#else
-	#define SIO_GP1X_CONFIG 0x01
-#endif
-
-/* Bit0 enables COM3's transceiver, bit1 disables the RS485 receiver (e.g. for IR). */
-#define SIO_GP2X_CONFIG 0x00
-
-static const u16 ec_init_table[] = { /* hi = data, lo = index */
-	0x1900,		/* Enable monitoring */
-	0x3050,		/* VIN4,5 enabled */
-	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
-	0x805C,		/* Unlock zero adjust */
-	0x7056, 0x3C57,	/* Zero adjust TMPIN1,2 */
-	0x005C,		/* Lock zero adjust */
-	0xD014		/* Also set FAN_CTL polarity to Active High */
-};
-
-static void init(struct device *dev)
-{
-	unsigned int gpio_base, i;
-	printk(BIOS_DEBUG, "LiPPERT LiteRunner-LX ENTER %s\n", __func__);
-
-	/* Init CS5536 GPIOs */
-	gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD,
-		    PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
-
-	outl(0x00000040, gpio_base + 0x00); // GPIO6  value      1 - LAN_PD#
-	outl(0x00000040, gpio_base + 0x04); // GPIO6  output     1 - LAN_PD#
-	outl(0x04000000, gpio_base + 0x18); // GPIO10 pull up    0 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1    1 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x20); // GPIO10 input      1 - THRM_ALRM#
-	outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2   1 - 32kHz
-	outl(0x00000800, gpio_base + 0x84); // GPIO27 output     1 - 32kHz
-	outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up    0 - 32kHz
-
-	/* Init Environment Controller. */
-	for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) {
-		u16 val = ec_init_table[i];
-		outb((u8)val, 0x0295);
-		outb(val >> 8, 0x0296);
-	}
-
-	/* bit2 = RS485_EN2, bit1 = RS485_EN1, bit0 = Live LED */
-	outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
-	/* bit1 = COM3_RX_EN, bit0 = COM3_TX_EN */
-	outb(SIO_GP2X_CONFIG, 0x1221); /* Simple-I/O GP27-20 */
-
-	printk(BIOS_DEBUG, "LiPPERT LiteRunner-LX EXIT %s\n", __func__);
-}
-
-static void mainboard_enable(struct device *dev)
-{
-	dev->ops->init = init;
-}
-
-struct chip_operations mainboard_ops = {
-	.enable_dev = mainboard_enable,
-};
diff --git a/src/mainboard/lippert/literunner-lx/romstage.c b/src/mainboard/lippert/literunner-lx/romstage.c
deleted file mode 100644
index b88a6a4ded22..000000000000
--- a/src/mainboard/lippert/literunner-lx/romstage.c
+++ /dev/null
@@ -1,182 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2007 Advanced Micro Devices, Inc.
- * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on romstage.c from the SpaceRunner-LX mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <spd.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <console/console.h>
-#include <cpu/x86/bist.h>
-#include <cpu/x86/msr.h>
-#include <cpu/amd/lxdef.h>
-#include <southbridge/amd/cs5536/cs5536.h>
-#include <southbridge/amd/cs5536/smbus.h>
-#include <superio/ite/common/ite.h>
-#include <superio/ite/it8712f/it8712f.h>
-#include <northbridge/amd/lx/raminit.h>
-
-#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1)
-#define GPIO_DEV PNP_DEV(0x2e, IT8712F_GPIO)
-
-/* Bit0 enables Spread Spectrum, bit1 makes on-board CF slot act as IDE slave. */
-#if IS_ENABLED(CONFIG_ONBOARD_IDE_SLAVE)
-	#define SMC_CONFIG	0x03
-#else
-	#define SMC_CONFIG	0x01
-#endif
-
-static const unsigned char spdbytes[] = {	// 4x Promos V58C2512164SA-J5I
-	0xFF, 0xFF,				// only values used by Geode-LX raminit.c are set
-	[SPD_MEMORY_TYPE]		= SPD_MEMORY_TYPE_SDRAM_DDR,	// (Fundamental) memory type
-	[SPD_NUM_ROWS]			= 0x0D,	// Number of row address bits [13]
-	[SPD_NUM_COLUMNS]		= 0x0A,	// Number of column address bits [10]
-	[SPD_NUM_DIMM_BANKS]		= 1,	// Number of module rows (banks)
-	0xFF, 0xFF, 0xFF,
-	[SPD_MIN_CYCLE_TIME_AT_CAS_MAX]	= 0x50,	// SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD]
-	0xFF, 0xFF,
-	[SPD_REFRESH]			= 0x82,	// Refresh rate/type [Self Refresh, 7.8 us]
-	[SPD_PRIMARY_SDRAM_WIDTH]	= 64,	// SDRAM width (primary SDRAM) [64 bits]
-	0xFF, 0xFF, 0xFF,
-	[SPD_NUM_BANKS_PER_SDRAM]	= 4,	// SDRAM device attributes, number of banks on SDRAM device
-	[SPD_ACCEPTABLE_CAS_LATENCIES]	= 0x1C,	// SDRAM device attributes, CAS latency [3, 2.5, 2]
-	0xFF, 0xFF,
-	[SPD_MODULE_ATTRIBUTES]		= 0x20,	// SDRAM module attributes [differential clk]
-	[SPD_DEVICE_ATTRIBUTES_GENERAL]	= 0x40,	// SDRAM device attributes, general [Concurrent AP]
-	[SPD_SDRAM_CYCLE_TIME_2ND]	= 0x60,	// SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD]
-	0xFF,
-	[SPD_SDRAM_CYCLE_TIME_3RD]	= 0x75,	// SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD]
-	0xFF,
-	[SPD_tRP]			= 60,	// Min. row precharge time [15 ns in units of 0.25 ns]
-	[SPD_tRRD]			= 40,	// Min. row active to row active [10 ns in units of 0.25 ns]
-	[SPD_tRCD]			= 60,	// Min. RAS to CAS delay [15 ns in units of 0.25 ns]
-	[SPD_tRAS]			= 40,	// Min. RAS pulse width = active to precharge delay [40 ns]
-	[SPD_BANK_DENSITY]		= 0x40,	// Density of each row on module [256 MB]
-	0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-	[SPD_tRFC]			= 70	// SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns]
-};
-
-int spd_read_byte(unsigned int device, unsigned int address)
-{
-	if (device != DIMM0)
-		return 0xFF;	/* No DIMM1, don't even try. */
-
-#if IS_ENABLED(CONFIG_DEBUG_SMBUS)
-	if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF)
-		printk(BIOS_ERR, "ERROR: spd_read_byte(DIMM0, 0x%02x) "
-			"returns 0xff\n", address);
-#endif
-
-	/* Fake SPD ROM value */
-	return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF;
-}
-
-/* Send config data to System Management Controller via SMB. */
-static int smc_send_config(unsigned char config_data)
-{
-	if (smbus_check_stop_condition(SMBUS_IO_BASE))
-		return 1;
-	if (smbus_start_condition(SMBUS_IO_BASE))
-		return 2;
-	if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address
-		return 3;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data
-		return 4;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length
-		return 5;
-	if (smbus_send_command(SMBUS_IO_BASE, config_data))
-		return 6;
-	smbus_stop_condition(SMBUS_IO_BASE);
-	return 0;
-}
-
-#include "northbridge/amd/lx/pll_reset.c"
-#include "cpu/amd/geode_lx/cpureginit.c"
-#include "cpu/amd/geode_lx/syspreinit.c"
-#include "cpu/amd/geode_lx/msrinit.c"
-
-static const u16 sio_init_table[] = { // hi = data, lo = index
-	0x072C,		// VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal
-	0x1423,		// don't delay PoWeROK1/2
-	0x9072,		// watchdog triggers PWROK, counts seconds
-#if !IS_ENABLED(CONFIG_USE_WATCHDOG_ON_BOOT)
-	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
-#endif
-	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xFF27, 0xDF28, 0x2729,	// (GP45 = SUSB, GP23,22,16,15 = SPI, GP13 = PWROK1)
-	0x66B8, 0x0FB9,	// enable pullups on SPI, RS485_EN, COM3_R/TX_EN
-	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED
-	0x03C1,		// enable Simple-I/O for GP21-20= COM3_RX_EN,TX_EN
-	0xFFC2,		// enable Simple-I/O for GP37-30
-	0x07C8,		// config GP12-10 as output
-	0x03C9,		// config GP21-20 as output
-	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x08F8,		// map GP LED Blinking 1 to GP10 = LIVE_LED (deactivate Simple I/O to use)
-};
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	int i;
-
-	/* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */
-	for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) {
-		u16 reg = sio_init_table[i];
-		ite_reg_write(GPIO_DEV, (u8) reg, (reg >> 8));
-	}
-}
-
-void asmlinkage mainboard_romstage_entry(unsigned long bist)
-{
-	int err;
-
-	static const struct mem_controller memctrl[] = {
-		{.channel0 = {DIMM0, DIMM1}}
-	};
-
-	SystemPreInit();
-	msr_init();
-
-	cs5536_early_setup();
-
-	/*
-	 * Note: Must do this AFTER the early_setup! It is counting on some
-	 * early MSR setup for CS5536.
-	 */
-	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
-	mb_gpio_init();
-	console_init();
-
-	/* Halt if there was a built in self test failure */
-	report_bist_failure(bist);
-
-	pll_reset();
-
-	cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
-
-	/* bit1 = on-board IDE is slave, bit0 = Spread Spectrum */
-	if ((err = smc_send_config(SMC_CONFIG))) {
-		printk(BIOS_ERR, "ERROR %d sending config data to SMC\n", err);
-	}
-
-	sdram_initialize(1, memctrl);
-
-	/* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
-}
diff --git a/src/mainboard/lippert/roadrunner-lx/Kconfig b/src/mainboard/lippert/roadrunner-lx/Kconfig
deleted file mode 100644
index 051713a27d45..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/Kconfig
+++ /dev/null
@@ -1,42 +0,0 @@
-if BOARD_LIPPERT_ROADRUNNER_LX
-
-config BOARD_SPECIFIC_OPTIONS # dummy
-	def_bool y
-	select CPU_AMD_GEODE_LX
-	select NORTHBRIDGE_AMD_LX
-	select SOUTHBRIDGE_AMD_CS5536
-	select SUPERIO_ITE_IT8712F
-	select HAVE_PIRQ_TABLE
-	select PIRQ_ROUTE
-	select UDELAY_TSC
-	# Standard chip is a 512 KB FWH. Replacing it with a 1 MB
-	# SST 49LF008A is possible.
-	select BOARD_ROMSIZE_KB_512
-	select POWER_BUTTON_FORCE_ENABLE
-	select PLL_MANUAL_CONFIG
-	select CORE_GLIU_500_333
-
-config MAINBOARD_DIR
-	string
-	default lippert/roadrunner-lx
-
-config MAINBOARD_PART_NUMBER
-	string
-	default "Cool RoadRunner-LX"
-
-config IRQ_SLOT_COUNT
-	int
-	default 7
-
-config ONBOARD_UARTS_RS485
-	bool "Switch on-board serial ports to RS485"
-	default n
-	help
-	  If selected, both on-board serial ports will operate in RS485 mode
-	  instead of RS232.
-
-config PLLMSRlo
-	hex
-	default 0x00de6001
-
-endif # BOARD_LIPPERT_ROADRUNNER_LX
diff --git a/src/mainboard/lippert/roadrunner-lx/Kconfig.name b/src/mainboard/lippert/roadrunner-lx/Kconfig.name
deleted file mode 100644
index e7185da0faa3..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/Kconfig.name
+++ /dev/null
@@ -1,2 +0,0 @@
-config BOARD_LIPPERT_ROADRUNNER_LX
-	bool "Cool RoadRunner-LX"
diff --git a/src/mainboard/lippert/roadrunner-lx/board_info.txt b/src/mainboard/lippert/roadrunner-lx/board_info.txt
deleted file mode 100644
index fc48fcd97323..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/board_info.txt
+++ /dev/null
@@ -1,6 +0,0 @@
-Category: half
-Board URL: http://www.adlinktech.com/PD/web/PD_detail.php?pid=1147
-ROM package: PLCC
-ROM protocol: FWH
-ROM socketed: y
-Flashrom support: y
diff --git a/src/mainboard/lippert/roadrunner-lx/devicetree.cb b/src/mainboard/lippert/roadrunner-lx/devicetree.cb
deleted file mode 100644
index f82368108d47..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/devicetree.cb
+++ /dev/null
@@ -1,89 +0,0 @@
-chip northbridge/amd/lx
-	device domain 0 on
-		device pci 1.0 on end		# Northbridge
-		device pci 1.1 on end		# Graphics
-		device pci 1.2 on end		# AES
-		chip southbridge/amd/cs5536		# Southbridge
-			# IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK
-			# SIRQ Mode = Active(Quiet) mode. Save power...
-			# Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse,
-			# UARTs, etc IRQs. OK
-			register "lpc_serirq_enable"			= "0x000012DA"	# 00010010 11011010
-			register "lpc_serirq_polarity"			= "0x0000ED25"	# inverse of above
-			register "lpc_serirq_mode"			= "1"
-			register "enable_gpio_int_route"		= "0x0D0C0700"
-			register "enable_ide_nand_flash"		= "0"	# 0:ide mode, 1:flash
-			register "enable_USBP4_device"			= "0"	# 0: host, 1:device
-			register "enable_USBP4_overcurrent"		= "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
-			register "com1_enable"				= "0"
-			register "com1_address"				= "0x3E8"
-			register "com1_irq"				= "6"
-			register "com2_enable"				= "0"
-			register "com2_address"				= "0x2E8"
-			register "com2_irq"				= "6"
-			register "unwanted_vpci[0]"			= "0"	# End of list has a zero
-			device pci 8.0 on end		# Slot4
-			device pci 9.0 on end		# Slot3
-			device pci a.0 on end		# Slot2
-			device pci b.0 on end		# Slot1
-			device pci c.0 on end		# IT8888
-			device pci e.0 on end		# Ethernet
-			device pci f.0 on			# ISA bridge
-				chip superio/ite/it8712f
-					device pnp 2e.0 off		# Floppy
-						io 0x60 = 0x3f0
-						irq 0x70 = 6
-						drq 0x74 = 2
-					end
-					device pnp 2e.1 on		# Com1
-						io 0x60 = 0x3f8
-						irq 0x70 = 4
-					end
-					device pnp 2e.2 on		# Com2
-						io 0x60 = 0x2f8
-						irq 0x70 = 3
-					end
-					device pnp 2e.3 on		# Parallel port
-						io 0x60 = 0x378
-						irq 0x70 = 7
-					end
-					device pnp 2e.4 on		# EC
-						io 0x60 = 0x290 # EC
-						io 0x62 = 0x298 # PME
-						irq 0x70 = 9
-					end
-					device pnp 2e.5 on		# PS/2 keyboard
-						io 0x60 = 0x60
-						io 0x62 = 0x64
-						irq 0x70 = 1
-					end
-					device pnp 2e.6 on		# PS/2 mouse
-						irq 0x70 = 12
-					end
-					device pnp 2e.7 on		# GPIO
-						io 0x62 = 0x1220 # Simple I/O
-						# io 0x64 = 0x1228 # SPI
-					end
-					device pnp 2e.8 off		# MIDI
-						io 0x60 = 0x300
-						irq 0x70 = 9
-					end
-					device pnp 2e.9 off		# Game port
-						io 0x60 = 0x220
-					end
-					device pnp 2e.a off end	# CIR
-				end
-			end
-			device pci f.2 on end		# IDE controller
-			device pci f.3 on end		# Audio
-			device pci f.4 on end		# OHCI
-			device pci f.5 on end		# EHCI
-		end
-	end
-	# APIC cluster is late CPU init.
-	device cpu_cluster 0 on
-		chip cpu/amd/geode_lx
-			device lapic 0 on end
-		end
-	end
-end
diff --git a/src/mainboard/lippert/roadrunner-lx/irq_tables.c b/src/mainboard/lippert/roadrunner-lx/irq_tables.c
deleted file mode 100644
index f5cf69882789..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/irq_tables.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on irq_tables.c from AMD's DB800 mainboard. */
-
-#include <arch/pirq_routing.h>
-#include <console/console.h>
-#include <arch/io.h>
-#include <arch/pirq_routing.h>
-#include "southbridge/amd/cs5536/cs5536.h"
-
-/* Platform IRQs */
-#define PIRQA 10
-#define PIRQB 11
-#define PIRQC 5
-#define PIRQD 15
-
-/* Map */
-#define M_PIRQA (1 << PIRQA)	/* Bitmap of supported IRQs */
-#define M_PIRQB (1 << PIRQB)	/* Bitmap of supported IRQs */
-#define M_PIRQC (1 << PIRQC)	/* Bitmap of supported IRQs */
-#define M_PIRQD (1 << PIRQD)	/* Bitmap of supported IRQs */
-
-/* Link */
-#define L_PIRQA	 1		/* Means Slot INTx# Connects To Chipset INTA# */
-#define L_PIRQB	 2		/* Means Slot INTx# Connects To Chipset INTB# */
-#define L_PIRQC	 3		/* Means Slot INTx# Connects To Chipset INTC# */
-#define L_PIRQD	 4		/* Means Slot INTx# Connects To Chipset INTD# */
-
-static const struct irq_routing_table intel_irq_routing_table = {
-	PIRQ_SIGNATURE,		/* u32 signature */
-	PIRQ_VERSION,		/* u16 version   */
-	32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* there can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
-	0x00,			/* Where the interrupt router lies (bus) */
-	(0x0F << 3) | 0x0,	/* Where the interrupt router lies (dev) */
-	0x00,			/* IRQs devoted exclusively to PCI usage */
-	0x100B,			/* Vendor */
-	0x002B,			/* Device */
-	0,			/* Miniport data */
-	{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},	/* u8 rfu[11] */
-	0xE0,			/* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
-	{
-		/* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
-		/* bus, dev|fn,           {link, bitmap},      {link, bitmap},     {link, bitmap},     {link, bitmap},     slot, rfu */
-		{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* CPU */
-		{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0},	/* chipset */
-		{0x00, (0x0E << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* ethernet */
-		{0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0},	/* slot1 */
-		{0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0},	/* slot2 */
-		{0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0},	/* slot3 */
-		{0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0},	/* slot4 */
-	}
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
-	return copy_pirq_routing_table(addr, &intel_irq_routing_table);
-}
diff --git a/src/mainboard/lippert/roadrunner-lx/mainboard.c b/src/mainboard/lippert/roadrunner-lx/mainboard.c
deleted file mode 100644
index b922e7872b2e..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/mainboard.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on mainboard.c from AMD's DB800 mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <console/console.h>
-#include <device/device.h>
-#include <arch/io.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-
-/* Bit1 switches Com1 to RS485, bit2 same for Com2, bit5 turns off the Live LED. */
-#if IS_ENABLED(CONFIG_ONBOARD_UARTS_RS485)
-	#define SIO_GP1X_CONFIG 0x26
-#else
-	#define SIO_GP1X_CONFIG 0x20
-#endif
-
-static const u16 ec_init_table[] = {	/* hi = data, lo = index */
-	0x1900,		/* Enable monitoring */
-	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
-	0x805C,		/* Unlock zero adjust */
-	0x7056, 0x3C57,	/* Zero adjust TMPIN1,2 */
-	0x005C,		/* Lock zero adjust */
-	0xD014		/* Also set FAN_CTL polarity to Active High */
-};
-
-static void init(struct device *dev)
-{
-	unsigned int gpio_base, i;
-	printk(BIOS_DEBUG, "LiPPERT RoadRunner-LX ENTER %s\n", __func__);
-
-	/* Init CS5536 GPIOs. */
-	gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD,
-		    PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
-
-	outl(0x00000040, gpio_base + 0x00); // GPIO6  value      1 - LAN_PD#
-	outl(0x00000040, gpio_base + 0x04); // GPIO6  output     1 - LAN_PD#
-	outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1    1 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x20); // GPIO10 input      1 - THRM_ALRM#
-	outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up    0 - PM-LED
-
-	/* Init Environment Controller. */
-	for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) {
-		u16 val = ec_init_table[i];
-		outb((u8)val, 0x0295);
-		outb(val >> 8, 0x0296);
-	}
-
-	/* bit5 = Live LED, bit2 = RS485_EN2, bit1 = RS485_EN1 */
-	outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
-	printk(BIOS_DEBUG, "LiPPERT RoadRunner-LX EXIT %s\n", __func__);
-}
-
-static void mainboard_enable(struct device *dev)
-{
-	dev->ops->init = init;
-}
-
-struct chip_operations mainboard_ops = {
-	.enable_dev = mainboard_enable,
-};
diff --git a/src/mainboard/lippert/roadrunner-lx/romstage.c b/src/mainboard/lippert/roadrunner-lx/romstage.c
deleted file mode 100644
index 49b333b590b1..000000000000
--- a/src/mainboard/lippert/roadrunner-lx/romstage.c
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- * Copyright (C) 2007 Advanced Micro Devices, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on romstage.c from AMD's DB800 and DBM690T mainboards. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <console/console.h>
-#include <cpu/x86/bist.h>
-#include <cpu/x86/msr.h>
-#include <cpu/amd/lxdef.h>
-#include <southbridge/amd/cs5536/cs5536.h>
-#include <spd.h>
-#include <superio/ite/common/ite.h>
-#include <superio/ite/it8712f/it8712f.h>
-#include <northbridge/amd/lx/raminit.h>
-
-#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1)
-#define GPIO_DEV PNP_DEV(0x2e, IT8712F_GPIO)
-
-int spd_read_byte(unsigned int device, unsigned int address)
-{
-	if (device != DIMM0)
-		return 0xFF;	/* No DIMM1, don't even try. */
-
-	return smbus_read_byte(device, address);
-}
-
-#include "northbridge/amd/lx/pll_reset.c"
-#include "cpu/amd/geode_lx/cpureginit.c"
-#include "cpu/amd/geode_lx/syspreinit.c"
-#include "cpu/amd/geode_lx/msrinit.c"
-
-static const u16 sio_init_table[] = {	// hi = data, lo = index
-	0x1E2C,		// disable ATXPG; VIN6,FAN4/5,VIN3 enabled, VIN7 internal
-	0x1423,		// don't delay PoWeROK1/2 - triggers 2nd reset
-	0x9072,		// watchdog triggers PWROK, counts seconds
-#if !IS_ENABLED(CONFIG_USE_WATCHDOG_ON_BOOT)
-	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
-#endif
-	0xBF25, 0x372A, 0xF326, // select GPIO function for most pins
-	0xBF27, 0xFF28, 0x2529, // (GP36 = FAN_CTL3, GP13 = PWROK1)
-	0x46B8, 0x0CB9,	// enable pullups on RS485_EN
-	0x36C0,		// enable Simple-I/O for GP15,14,12,11= LIVE_LED, WD_ACTIVE, RS485_EN2,1
-	0xFFC3,		// enable Simple-I/O for GP47-40 (GPIOs on Supervisory Connector)
-	0x26C8,		// config GP15,12,11 as output; GP14 as input
-	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x0DF8,		// map GP LED Blinking 1 to GP15 = LIVE_LED (deactivate Simple-I/O to use)
-};
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	int i;
-
-	/* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */
-	for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) {
-		u16 reg = sio_init_table[i];
-		ite_reg_write(GPIO_DEV, (u8) reg, (reg >> 8));
-	}
-}
-
-void asmlinkage mainboard_romstage_entry(unsigned long bist)
-{
-
-	static const struct mem_controller memctrl[] = {
-		{.channel0 = {DIMM0, DIMM1}}
-	};
-
-	SystemPreInit();
-	msr_init();
-
-	cs5536_early_setup();
-
-	/*
-	 * Note: must do this AFTER the early_setup! It is counting on some
-	 * early MSR setup for CS5536.
-	 */
-	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
-	mb_gpio_init();
-	console_init();
-
-	/* Halt if there was a built in self test failure */
-	report_bist_failure(bist);
-
-	pll_reset();
-
-	cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
-
-	sdram_initialize(1, memctrl);
-
-	/* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
-}
diff --git a/src/mainboard/lippert/spacerunner-lx/Kconfig b/src/mainboard/lippert/spacerunner-lx/Kconfig
deleted file mode 100644
index 65645fdbf041..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/Kconfig
+++ /dev/null
@@ -1,49 +0,0 @@
-if BOARD_LIPPERT_SPACERUNNER_LX
-
-config BOARD_SPECIFIC_OPTIONS # dummy
-	def_bool y
-	select CPU_AMD_GEODE_LX
-	select NORTHBRIDGE_AMD_LX
-	select SOUTHBRIDGE_AMD_CS5536
-	select SUPERIO_ITE_IT8712F
-	select HAVE_DEBUG_SMBUS
-	select HAVE_PIRQ_TABLE
-	select PIRQ_ROUTE
-	select UDELAY_TSC
-	# Board is equipped with a 1 MB SPI flash, however, due to limitations
-	# of the IT8712F Super I/O, only the top 512 KB are directly mapped.
-	select BOARD_ROMSIZE_KB_512
-	select POWER_BUTTON_FORCE_ENABLE
-	select PLL_MANUAL_CONFIG
-	select CORE_GLIU_500_400
-
-config MAINBOARD_DIR
-	string
-	default lippert/spacerunner-lx
-
-config MAINBOARD_PART_NUMBER
-	string
-	default "Cool SpaceRunner-LX"
-
-config IRQ_SLOT_COUNT
-	int
-	default 7
-
-config ONBOARD_UARTS_RS485
-	bool "Switch on-board serial ports to RS485"
-	default n
-	help
-	  If selected, both on-board serial ports will operate in RS485 mode
-	  instead of RS232.
-
-config ONBOARD_IDE_SLAVE
-	bool "Make on-board SSD act as Slave"
-	default n
-	help
-	  If selected, the on-board SSD will act as IDE Slave instead of Master.
-
-config PLLMSRlo
-	hex
-	default 0x00de6001
-
-endif # BOARD_LIPPERT_SPACERUNNER_LX
diff --git a/src/mainboard/lippert/spacerunner-lx/Kconfig.name b/src/mainboard/lippert/spacerunner-lx/Kconfig.name
deleted file mode 100644
index 85eec9638260..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/Kconfig.name
+++ /dev/null
@@ -1,2 +0,0 @@
-config BOARD_LIPPERT_SPACERUNNER_LX
-	bool "Cool SpaceRunner-LX"
diff --git a/src/mainboard/lippert/spacerunner-lx/board_info.txt b/src/mainboard/lippert/spacerunner-lx/board_info.txt
deleted file mode 100644
index 76be510bb61c..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/board_info.txt
+++ /dev/null
@@ -1,6 +0,0 @@
-Category: half
-Board URL: http://www.adlinktech.com/PD/web/PD_detail.php?pid=1148
-ROM package: SOIC8
-ROM protocol: SPI
-ROM socketed: n
-Flashrom support: n
diff --git a/src/mainboard/lippert/spacerunner-lx/devicetree.cb b/src/mainboard/lippert/spacerunner-lx/devicetree.cb
deleted file mode 100644
index 5f5b15bbb60f..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/devicetree.cb
+++ /dev/null
@@ -1,90 +0,0 @@
-chip northbridge/amd/lx
-	device domain 0 on
-		device pci 1.0 on end				# Northbridge
-		device pci 1.1 on end				# Graphics
-		device pci 1.2 on end				# AES
-		chip southbridge/amd/cs5536
-			# IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK
-			# SIRQ Mode = Active(Quiet) mode. Save power....
-			# Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse,
-			# UARTs, etc IRQs. OK
-			register "lpc_serirq_enable"			= "0x000012DA" # 00010010 11011010
-			register "lpc_serirq_polarity"			= "0x0000ED25" # inverse of above
-			register "lpc_serirq_mode"			= "1"
-			register "enable_gpio_int_route"		= "0x0D0C0700"
-			register "enable_ide_nand_flash"		= "0" # 0:ide mode, 1:flash
-			register "enable_USBP4_device"			= "0" # 0:host, 1:device
-			register "enable_USBP4_overcurrent"		= "0" # 0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
-			register "com1_enable"				= "0"
-			register "com1_address"				= "0x3E8"
-			register "com1_irq"				= "6"
-			register "com2_enable"				= "0"
-			register "com2_address"				= "0x2E8"
-			register "com2_irq"				= "6"
-			register "unwanted_vpci[0]"			= "0x80007B00" # Audio: 1 << 31 + Device 0x0F << 11 + Function 3 << 8
-			register "unwanted_vpci[1]"			= "0" # End of list has a zero
-			device pci 8.0 on end		# Slot4
-			device pci 9.0 on end		# Slot3
-			device pci a.0 on end		# Slot2
-			device pci b.0 on end		# Slot1
-			device pci c.0 on end		# IT8888
-			device pci e.0 on end		# Ethernet
-			device pci f.0 on			# ISA Bridge
-				chip superio/ite/it8712f
-					device pnp 2e.0 off		# Floppy
-						io 0x60 = 0x3f0
-						irq 0x70 = 6
-						drq 0x74 = 2
-					end
-					device pnp 2e.1 on		# Com1
-						io 0x60 = 0x3f8
-						irq 0x70 = 4
-					end
-					device pnp 2e.2 on		# Com2
-						io 0x60 = 0x2f8
-						irq 0x70 = 3
-					end
-					device pnp 2e.3 on		# Parallel port
-						io 0x60 = 0x378
-						irq 0x70 = 7
-					end
-					device pnp 2e.4 on		# EC
-						io 0x60 = 0x290 # EC
-						io 0x62 = 0x298 # PME
-						irq 0x70 = 9
-					end
-					device pnp 2e.5 on		# PS/2 keyboard
-						io 0x60 = 0x60
-						io 0x62 = 0x64
-						irq 0x70 = 1
-					end
-					device pnp 2e.6 on		# PS/2 mouse
-						irq 0x70 = 12
-					end
-					device pnp 2e.7 on		# GPIO
-						io 0x62 = 0x1220 # Simple I/O
-						io 0x64 = 0x1228 # SPI
-					end
-					device pnp 2e.8 off		# MIDI
-						io 0x60 = 0x300
-						irq 0x70 = 9
-					end
-					device pnp 2e.9 off		# Game port
-						io 0x60 = 0x220
-					end
-					device pnp 2e.a off end	# CIR
-				end
-			end
-			device pci f.2 on end		# IDE
-			device pci f.3 off end		# Audio
-			device pci f.4 on end		# OHCI
-			device pci f.5 on end		# EHCI
-		end
-	end
-	# APIC cluster is late CPU init.
-	device cpu_cluster 0 on
-		chip cpu/amd/geode_lx
-			device lapic 0 on end
-		end
-	end
-end
diff --git a/src/mainboard/lippert/spacerunner-lx/irq_tables.c b/src/mainboard/lippert/spacerunner-lx/irq_tables.c
deleted file mode 100644
index 37e82e5cf4ae..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/irq_tables.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on irq_tables.c from AMD's DB800 mainboard. */
-
-#include <arch/pirq_routing.h>
-#include <console/console.h>
-#include <arch/io.h>
-#include <arch/pirq_routing.h>
-#include "southbridge/amd/cs5536/cs5536.h"
-
-/* Platform IRQs */
-#define PIRQA 10
-#define PIRQB 11
-#define PIRQC 5
-#define PIRQD 15
-
-/* Map */
-#define M_PIRQA (1 << PIRQA)	/* Bitmap of supported IRQs */
-#define M_PIRQB (1 << PIRQB)	/* Bitmap of supported IRQs */
-#define M_PIRQC (1 << PIRQC)	/* Bitmap of supported IRQs */
-#define M_PIRQD (1 << PIRQD)	/* Bitmap of supported IRQs */
-
-/* Link */
-#define L_PIRQA	 1		/* Means Slot INTx# Connects To Chipset INTA# */
-#define L_PIRQB	 2		/* Means Slot INTx# Connects To Chipset INTB# */
-#define L_PIRQC	 3		/* Means Slot INTx# Connects To Chipset INTC# */
-#define L_PIRQD	 4		/* Means Slot INTx# Connects To Chipset INTD# */
-
-static const struct irq_routing_table intel_irq_routing_table = {
-	PIRQ_SIGNATURE,		/* u32 signature */
-	PIRQ_VERSION,		/* u16 version   */
-	32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* There can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
-	0x00,			/* Where the interrupt router lies (bus) */
-	(0x0F << 3) | 0x0,	/* Where the interrupt router lies (dev) */
-	0x00,			/* IRQs devoted exclusively to PCI usage */
-	0x100B,			/* Vendor */
-	0x002B,			/* Device */
-	0,			/* Miniport data */
-	{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},	/* u8 rfu[11] */
-	0xE0,			/* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
-	{
-		/* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
-		/* bus, dev|fn,           {link, bitmap},      {link, bitmap},     {link, bitmap},     {link, bitmap},     slot, rfu */
-		{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* CPU */
-		{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0},	/* chipset */
-		{0x00, (0x0E << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00},       {0x00, 0x00},       {0x00, 0x00}},       0x0, 0x0},	/* ethernet */
-		{0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0},	/* slot1 */
-		{0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0},	/* slot2 */
-		{0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0},	/* slot3 */
-		{0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0},	/* slot4 */
-	}
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
-	return copy_pirq_routing_table(addr, &intel_irq_routing_table);
-}
diff --git a/src/mainboard/lippert/spacerunner-lx/mainboard.c b/src/mainboard/lippert/spacerunner-lx/mainboard.c
deleted file mode 100644
index 594545d14617..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/mainboard.c
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on mainboard.c from AMD's DB800 mainboard. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <console/console.h>
-#include <device/device.h>
-#include <arch/io.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-
-/* Bit0 turns off the Live LED, bit1 switches Com1 to RS485, bit2 same for Com2. */
-#if IS_ENABLED(CONFIG_ONBOARD_UARTS_RS485)
-	#define SIO_GP1X_CONFIG 0x07
-#else
-	#define SIO_GP1X_CONFIG 0x01
-#endif
-
-static const u16 ec_init_table[] = { /* hi = data, lo = index */
-	0x1900,		/* Enable monitoring */
-	0x3050,		/* VIN4,5 enabled */
-	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
-	0x805C,		/* Unlock zero adjust */
-	0x7056, 0x3C57,	/* Zero adjust TMPIN1,2 */
-	0x005C,		/* Lock zero adjust */
-	0xD014		/* Also set FAN_CTL polarity to Active High */
-};
-
-static void init(struct device *dev)
-{
-	unsigned int gpio_base, i;
-	printk(BIOS_DEBUG, "LiPPERT SpaceRunner-LX ENTER %s\n", __func__);
-
-	/* Init CS5536 GPIOs */
-	gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD,
-		    PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
-
-	outl(0x00000040, gpio_base + 0x00); // GPIO6  value      1 - LAN_PD#
-	outl(0x00000040, gpio_base + 0x04); // GPIO6  output     1 - LAN_PD#
-	outl(0x04000000, gpio_base + 0x18); // GPIO10 pull up    0 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1    1 - THRM_ALRM#
-	outl(0x00000400, gpio_base + 0x20); // GPIO10 input      1 - THRM_ALRM#
-	outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2   1 - 32kHz
-	outl(0x00000800, gpio_base + 0x84); // GPIO27 output     1 - 32kHz
-	outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up    0 - 32kHz
-
-	/* Init Environment Controller. */
-	for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) {
-		u16 val = ec_init_table[i];
-		outb((u8)val, 0x0295);
-		outb(val >> 8, 0x0296);
-	}
-
-	/* bit2 = RS485_EN2, bit1 = RS485_EN1, bit0 = Live LED */
-	outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
-
-	printk(BIOS_DEBUG, "LiPPERT SpaceRunner-LX EXIT %s\n", __func__);
-}
-
-static void mainboard_enable(struct device *dev)
-{
-	dev->ops->init = init;
-}
-
-struct chip_operations mainboard_ops = {
-	.enable_dev = mainboard_enable,
-};
diff --git a/src/mainboard/lippert/spacerunner-lx/romstage.c b/src/mainboard/lippert/spacerunner-lx/romstage.c
deleted file mode 100644
index a8885700ef0f..000000000000
--- a/src/mainboard/lippert/spacerunner-lx/romstage.c
+++ /dev/null
@@ -1,181 +0,0 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2007 Advanced Micro Devices, Inc.
- * Copyright (C) 2008 LiPPERT Embedded Computers GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/* Based on romstage.c from AMD's DB800 and DBM690T mainboards. */
-
-#include <stdlib.h>
-#include <stdint.h>
-#include <spd.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <console/console.h>
-#include <cpu/x86/bist.h>
-#include <cpu/x86/msr.h>
-#include <cpu/amd/lxdef.h>
-#include <southbridge/amd/cs5536/cs5536.h>
-#include <southbridge/amd/cs5536/smbus.h>
-#include <superio/ite/common/ite.h>
-#include <superio/ite/it8712f/it8712f.h>
-#include <northbridge/amd/lx/raminit.h>
-
-#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1)
-#define GPIO_DEV PNP_DEV(0x2e, IT8712F_GPIO)
-
-/* Bit0 enables Spread Spectrum, bit1 makes on-board SSD act as IDE slave. */
-#if IS_ENABLED(CONFIG_ONBOARD_IDE_SLAVE)
-	#define SMC_CONFIG	0x03
-#else
-	#define SMC_CONFIG	0x01
-#endif
-
-static const unsigned char spdbytes[] = {	// 4x Promos V58C2512164SA-J5I
-	0xFF, 0xFF,				// only values used by Geode-LX raminit.c are set
-	[SPD_MEMORY_TYPE]		= SPD_MEMORY_TYPE_SDRAM_DDR,	// (Fundamental) memory type
-	[SPD_NUM_ROWS]			= 0x0D,	// Number of row address bits [13]
-	[SPD_NUM_COLUMNS]		= 0x0A,	// Number of column address bits [10]
-	[SPD_NUM_DIMM_BANKS]		= 1,	// Number of module rows (banks)
-	0xFF, 0xFF, 0xFF,
-	[SPD_MIN_CYCLE_TIME_AT_CAS_MAX]	= 0x50,	// SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD]
-	0xFF, 0xFF,
-	[SPD_REFRESH]			= 0x82,	// Refresh rate/type [Self Refresh, 7.8 us]
-	[SPD_PRIMARY_SDRAM_WIDTH]	= 64,	// SDRAM width (primary SDRAM) [64 bits]
-	0xFF, 0xFF, 0xFF,
-	[SPD_NUM_BANKS_PER_SDRAM]	= 4,	// SDRAM device attributes, number of banks on SDRAM device
-	[SPD_ACCEPTABLE_CAS_LATENCIES]	= 0x1C,	// SDRAM device attributes, CAS latency [3, 2.5, 2]
-	0xFF, 0xFF,
-	[SPD_MODULE_ATTRIBUTES]		= 0x20,	// SDRAM module attributes [differential clk]
-	[SPD_DEVICE_ATTRIBUTES_GENERAL]	= 0x40,	// SDRAM device attributes, general [Concurrent AP]
-	[SPD_SDRAM_CYCLE_TIME_2ND]	= 0x60,	// SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD]
-	0xFF,
-	[SPD_SDRAM_CYCLE_TIME_3RD]	= 0x75,	// SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD]
-	0xFF,
-	[SPD_tRP]			= 60,	// Min. row precharge time [15 ns in units of 0.25 ns]
-	[SPD_tRRD]			= 40,	// Min. row active to row active [10 ns in units of 0.25 ns]
-	[SPD_tRCD]			= 60,	// Min. RAS to CAS delay [15 ns in units of 0.25 ns]
-	[SPD_tRAS]			= 40,	// Min. RAS pulse width = active to precharge delay [40 ns]
-	[SPD_BANK_DENSITY]		= 0x40,	// Density of each row on module [256 MB]
-	0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-	[SPD_tRFC]			= 70	// SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns]
-};
-
-int spd_read_byte(unsigned int device, unsigned int address)
-{
-	if (device != DIMM0)
-		return 0xFF;	/* No DIMM1, don't even try. */
-
-#if IS_ENABLED(CONFIG_DEBUG_SMBUS)
-	if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) {
-		printk(BIOS_ERR, "ERROR: spd_read_byte(DIMM0, 0x%02x) "
-			"returns 0xff\n", address);
-	}
-#endif
-
-	/* Fake SPD ROM value */
-	return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF;
-}
-
-/* Send config data to System Management Controller via SMB. */
-static int smc_send_config(unsigned char config_data)
-{
-	if (smbus_check_stop_condition(SMBUS_IO_BASE))
-		return 1;
-	if (smbus_start_condition(SMBUS_IO_BASE))
-		return 2;
-	if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address
-		return 3;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data
-		return 4;
-	if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length
-		return 5;
-	if (smbus_send_command(SMBUS_IO_BASE, config_data))
-		return 6;
-	smbus_stop_condition(SMBUS_IO_BASE);
-	return 0;
-}
-
-#include "northbridge/amd/lx/pll_reset.c"
-#include "cpu/amd/geode_lx/cpureginit.c"
-#include "cpu/amd/geode_lx/syspreinit.c"
-#include "cpu/amd/geode_lx/msrinit.c"
-
-static const u16 sio_init_table[] = { // hi = data, lo = index
-	0x072C,		// VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal
-	0x1423,		// don't delay PoWeROK1/2
-	0x9072,		// watchdog triggers PWROK, counts seconds
-#if !IS_ENABLED(CONFIG_USE_WATCHDOG_ON_BOOT)
-	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
-#endif
-	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xFF27, 0xDF28, 0x2729,	// (GP45 = SUSB, GP23,22,16,15 = SPI, GP13 = PWROK1)
-	0x66B8, 0x0CB9,	// enable pullups on SPI, RS485_EN
-	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED
-	0x07C8,		// config GP12-10 as output
-	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x08F8,		// map GP LED Blinking 1 to GP10 = LIVE_LED (deactivate Simple I/O to use)
-};
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
-	int i;
-
-	/* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */
-	for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) {
-		u16 reg = sio_init_table[i];
-		ite_reg_write(GPIO_DEV, (u8) reg, (reg >> 8));
-	}
-}
-
-void asmlinkage mainboard_romstage_entry(unsigned long bist)
-{
-	int err;
-
-	static const struct mem_controller memctrl[] = {
-		{.channel0 = {DIMM0, DIMM1}}
-	};
-
-	SystemPreInit();
-	msr_init();
-
-	cs5536_early_setup();
-
-	/*
-	 * Note: Must do this AFTER the early_setup! It is counting on some
-	 * early MSR setup for CS5536.
-	 */
-	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
-	mb_gpio_init();
-	console_init();
-
-	/* Halt if there was a built in self test failure */
-	report_bist_failure(bist);
-
-	pll_reset();
-
-	cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
-
-	/* bit1 = on-board IDE is slave, bit0 = Spread Spectrum */
-	if ((err = smc_send_config(SMC_CONFIG))) {
-		printk(BIOS_ERR, "ERROR %d sending config data to SMC\n", err);
-	}
-
-	sdram_initialize(1, memctrl);
-
-	/* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
-	return;
-}