soc/qualcomm/common: Move UART SC7180 driver to common section

Move existing UART driver from sc7180 to common folder.

This implements UART driver for QCOM SoC's

BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.

Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I7bc2d3765f956e04bae3e45c3a9b9e2ad424c7b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>

1 files changed, 154 insertions, 0 deletions

diff --git a/src/soc/qualcomm/common/qupv3_uart.c b/src/soc/qualcomm/common/qupv3_uart.c
new file mode 100644
index 000000000000..2086c1df70a1
--- /dev/null
+++ b/src/soc/qualcomm/common/qupv3_uart.c
@@ -0,0 +1,154 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <assert.h>
+#include <boot/coreboot_tables.h>
+#include <console/uart.h>
+#include <soc/clock.h>
+#include <soc/qcom_qup_se.h>
+#include <soc/qup_se_handlers_common.h>
+#include <soc/qupv3_config_common.h>
+#include <types.h>
+
+/* COMMON STATUS/CONFIGURATION REGISTERS AND MASKS */
+
+#define GENI_STATUS_M_GENI_CMD_ACTIVE_MASK	0x1
+#define GENI_STATUS_S_GENI_CMD_ACTIVE_MASK	0x1000
+
+#define UART_TX_WATERMARK_MARGIN	4	/* Represented in words */
+#define UART_RX_WATERMARK_MARGIN	8	/* Represented in words */
+#define UART_RX_RFR_WATERMARK_MARGIN	4	/* Represented in words */
+#define UART_TX_BITS_PER_WORD	8
+#define UART_RX_BITS_PER_WORD	8
+#define START_UART_TX		0x8000000
+#define START_UART_RX		0x8000000
+
+/* UART FIFO Packing Configuration. */
+/* Start_idx:0, direction:0, len:7, stop:0 */
+#define UART_TX_PACK_VECTOR0	0x0E
+/* Start_idx:8, direction:0, len:7, stop:0 */
+#define UART_TX_PACK_VECTOR1	0x10E
+/* Start_idx:16, direction:0, len:7, stop:0 */
+#define UART_TX_PACK_VECTOR2	0x20E
+/* Start_idx:24, direction:0, len:7, stop:1 */
+#define UART_TX_PACK_VECTOR3	0x30F
+/* Start_idx:0, direction:0, len:7, stop:1 */
+#define UART_RX_PACK_VECTOR0	0xF
+#define UART_RX_PACK_VECTOR2	0x00
+
+void uart_tx_flush(unsigned int idx)
+{
+	struct qup_regs *regs = qup[idx].regs;
+
+	while (read32(&regs->geni_status) &
+	       GENI_STATUS_M_GENI_CMD_ACTIVE_MASK)
+		;
+}
+
+void uart_init(unsigned int idx)
+{
+	struct qup_regs *regs = qup[idx].regs;
+	unsigned int reg_value;
+	unsigned int div, baud_rate, uart_freq;
+
+	/*
+	 * If the RX (secondary) sequencer is already active, it means the core
+	 * has been already initialized in the previous stage. Skip
+	 * configuration
+	 */
+	if (read32(&regs->geni_status) & GENI_STATUS_S_GENI_CMD_ACTIVE_MASK)
+		return;
+
+	qupv3_se_fw_load_and_init(idx, SE_PROTOCOL_UART, FIFO);
+	clock_enable_qup(idx);
+
+	reg_value = read32(&regs->geni_fw_revision_ro);
+	reg_value &= GENI_FW_REVISION_RO_PROTOCOL_MASK;
+	reg_value >>= GENI_FW_REVISION_RO_PROTOCOL_SHIFT;
+
+	assert(reg_value == SE_PROTOCOL_UART);
+
+	baud_rate = get_uart_baudrate();
+
+	/*requires 16 clock pulses to sample 1 bit of data */
+	uart_freq = baud_rate * 16;
+
+	div = DIV_ROUND_CLOSEST(SRC_XO_HZ, uart_freq);
+	write32(&regs->geni_ser_m_clk_cfg, (div << 4) | 1);
+	write32(&regs->geni_ser_s_clk_cfg, (div << 4) | 1);
+
+	/* GPIO Configuration */
+	gpio_configure(qup[idx].pin[2], qup[idx].func[2], GPIO_PULL_UP,
+				GPIO_2MA, GPIO_OUTPUT);
+	gpio_configure(qup[idx].pin[3], qup[idx].func[3], GPIO_PULL_UP,
+				GPIO_2MA, GPIO_INPUT);
+
+	write32(&regs->geni_tx_watermark_reg, UART_TX_WATERMARK_MARGIN);
+	write32(&regs->geni_rx_watermark_reg, FIFO_DEPTH
+					- UART_RX_WATERMARK_MARGIN);
+	write32(&regs->geni_rx_rfr_watermark_reg,
+			FIFO_DEPTH - UART_RX_RFR_WATERMARK_MARGIN);
+
+	write32(&regs->uart_tx_word_len, UART_TX_BITS_PER_WORD);
+	write32(&regs->uart_rx_word_len, UART_RX_BITS_PER_WORD);
+
+	/* Disable TX parity calculation */
+	write32(&regs->uart_tx_parity_cfg, 0x0);
+	/* Ignore CTS line status for TX communication */
+	write32(&regs->uart_tx_trans_cfg_reg, 0x2);
+	/* Disable RX parity calculation */
+	write32(&regs->uart_rx_parity_cfg, 0x0);
+	/* Disable parity, framing and break check on received word */
+	write32(&regs->uart_rx_trans_cfg, 0x0);
+	/* Set UART TX stop bit len to one UART bit length */
+	write32(&regs->uart_tx_stop_bit_len, 0x0);
+	write32(&regs->uart_rx_stale_cnt, 0x16 * 10);
+
+	write32(&regs->geni_tx_packing_cfg0, UART_TX_PACK_VECTOR0 |
+						(UART_TX_PACK_VECTOR1 << 10));
+	write32(&regs->geni_tx_packing_cfg1, UART_TX_PACK_VECTOR2 |
+						(UART_TX_PACK_VECTOR3 << 10));
+	write32(&regs->geni_rx_packing_cfg0, UART_RX_PACK_VECTOR0);
+	write32(&regs->geni_rx_packing_cfg1, UART_RX_PACK_VECTOR2);
+
+	/* Start RX */
+	write32(&regs->geni_s_cmd0, START_UART_RX);
+}
+
+unsigned char uart_rx_byte(unsigned int idx)
+{
+	struct qup_regs *regs = qup[idx].regs;
+
+	if (read32(&regs->geni_rx_fifo_status) & RX_FIFO_WC_MSK)
+		return read32(&regs->geni_rx_fifon) & 0xFF;
+	return 0;
+}
+
+void uart_tx_byte(unsigned int idx, unsigned char data)
+{
+	struct qup_regs *regs = qup[idx].regs;
+
+	uart_tx_flush(idx);
+
+	write32(&regs->uart_tx_trans_len, 1);
+	/* Start TX */
+	write32(&regs->geni_m_cmd0, START_UART_TX);
+	write32(&regs->geni_tx_fifon, data);
+}
+
+uintptr_t uart_platform_base(unsigned int idx)
+{
+	return (uintptr_t)qup[idx].regs;
+}
+
+void uart_fill_lb(void *data)
+{
+	struct lb_serial serial = {0};
+
+	serial.type = LB_SERIAL_TYPE_MEMORY_MAPPED;
+	serial.baseaddr = (uint32_t)uart_platform_base(CONFIG_UART_FOR_CONSOLE);
+	serial.baud = get_uart_baudrate();
+	serial.regwidth = 4;
+	serial.input_hertz = SRC_XO_HZ;
+
+	lb_add_serial(&serial, data);
+}