Revert "mb/aopen/dxplplusu: Remove board"

This reverts commit eb76a455cd39ec59b7f2ba28baeec9538befd59e
and applies minor fixes to make it build again.

PARALLEL_MP was working prior to board removal and no
relevant SMI handlers were implemented. So NO_SMM choice
is now selected.

Change-Id: Ia1cd02278240d1b5d006fb2a7730d3d86390f85b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>

1 files changed, 328 insertions, 0 deletions

diff --git a/src/southbridge/intel/i82801dx/lpc.c b/src/southbridge/intel/i82801dx/lpc.c
new file mode 100644
index 000000000000..1de376656359
--- /dev/null
+++ b/src/southbridge/intel/i82801dx/lpc.c
@@ -0,0 +1,328 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <arch/hpet.h>
+#include <arch/io.h>
+#include <arch/ioapic.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <option.h>
+#include <pc80/mc146818rtc.h>
+#include <pc80/isa-dma.h>
+#include <pc80/i8259.h>
+#include "chip.h"
+#include "i82801dx.h"
+
+#define NMI_OFF 0
+
+typedef struct southbridge_intel_i82801dx_config config_t;
+
+/**
+ * Enable ACPI I/O range.
+ *
+ * @param dev PCI device with ACPI and PM BAR's
+ */
+static void i82801dx_enable_acpi(struct device *dev)
+{
+	/* Set ACPI base address (I/O space). */
+	pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
+
+	/* Enable ACPI I/O range decode and ACPI power management. */
+	pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
+}
+
+/**
+ * Set miscellaneous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801dx_enable_ioapic(struct device *dev)
+{
+	u32 reg32;
+
+	reg32 = pci_read_config32(dev, GEN_CNTL);
+	reg32 |= (1 << 13);	/* Coprocessor error enable (COPR_ERR_EN) */
+	reg32 |= (3 << 7);	/* IOAPIC enable (APIC_EN) */
+	reg32 |= (1 << 2);	/* DMA collection buffer enable (DCB_EN) */
+	reg32 |= (1 << 1);	/* Delayed transaction enable (DTE) */
+	pci_write_config32(dev, GEN_CNTL, reg32);
+	printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
+
+	setup_ioapic(VIO_APIC_VADDR, 0x02);
+
+	ioapic_set_boot_config(VIO_APIC_VADDR, true);
+}
+
+static void i82801dx_enable_serial_irqs(struct device *dev)
+{
+	/* Set packet length and toggle silent mode bit. */
+	pci_write_config8(dev, SERIRQ_CNTL,
+			  (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0));
+	pci_write_config8(dev, SERIRQ_CNTL,
+			  (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0));
+}
+
+static void i82801dx_pirq_init(struct device *dev)
+{
+	/* Get the chip configuration */
+	config_t *config = dev->chip_info;
+
+	pci_write_config8(dev, PIRQA_ROUT, config->pirqa_routing);
+	pci_write_config8(dev, PIRQB_ROUT, config->pirqb_routing);
+	pci_write_config8(dev, PIRQC_ROUT, config->pirqc_routing);
+	pci_write_config8(dev, PIRQD_ROUT, config->pirqd_routing);
+	pci_write_config8(dev, PIRQE_ROUT, config->pirqe_routing);
+	pci_write_config8(dev, PIRQF_ROUT, config->pirqf_routing);
+	pci_write_config8(dev, PIRQG_ROUT, config->pirqg_routing);
+	pci_write_config8(dev, PIRQH_ROUT, config->pirqh_routing);
+}
+
+static void i82801dx_power_options(struct device *dev)
+{
+	u8 reg8;
+	u16 reg16, pmbase;
+	u32 reg32;
+	const char *state;
+
+	/* Which state do we want to goto after g3 (power restored)?
+	 * 0 == S0 Full On
+	 * 1 == S5 Soft Off
+	 *
+	 * If the option is not existent (Laptops), use MAINBOARD_POWER_ON.
+	 */
+	const unsigned int pwr_on = get_uint_option("power_on_after_fail", MAINBOARD_POWER_ON);
+
+	reg8 = pci_read_config8(dev, GEN_PMCON_3);
+	reg8 &= 0xfe;
+	switch (pwr_on)	{
+	case MAINBOARD_POWER_OFF:
+		reg8 |= 1;
+		state = "off";
+		break;
+	case MAINBOARD_POWER_ON:
+		reg8 &= ~1;
+		state = "on";
+		break;
+	case MAINBOARD_POWER_KEEP:
+		reg8 &= ~1;
+		state = "state keep";
+		break;
+	default:
+		state = "undefined";
+	}
+
+	reg8 &= ~(1 << 3);	/* minimum assertion is 1 to 2 RTCCLK */
+
+	pci_write_config8(dev, GEN_PMCON_3, reg8);
+	printk(BIOS_INFO, "Set power %s after power failure.\n", state);
+
+	/* Set up NMI on errors. */
+	reg8 = inb(0x61);
+	reg8 &= 0x0f;		/* Higher Nibble must be 0 */
+	reg8 &= ~(1 << 3);	/* IOCHK# NMI Enable */
+	// reg8 &= ~(1 << 2);	/* PCI SERR# Enable */
+	reg8 |= (1 << 2); /* PCI SERR# Disable for now */
+	outb(reg8, 0x61);
+
+	reg8 = inb(0x70);
+	const unsigned int nmi_option = get_uint_option("nmi", NMI_OFF);
+	if (nmi_option) {
+		printk(BIOS_INFO, "NMI sources enabled.\n");
+		reg8 &= ~(1 << 7);	/* Set NMI. */
+	} else {
+		printk(BIOS_INFO, "NMI sources disabled.\n");
+		reg8 |= (1 << 7);	/* Disable NMI. */
+	}
+	outb(reg8, 0x70);
+
+	/* Set SMI# rate down and enable CPU_SLP# */
+	reg16 = pci_read_config16(dev, GEN_PMCON_1);
+	reg16 &= ~(3 << 0);	// SMI# rate 1 minute
+	reg16 |= (1 << 5);	// CPUSLP_EN Desktop only
+	pci_write_config16(dev, GEN_PMCON_1, reg16);
+
+	pmbase = pci_read_config16(dev, 0x40) & 0xfffe;
+
+	/* Set up power management block and determine sleep mode */
+	reg32 = inl(pmbase + 0x04); // PM1_CNT
+
+	reg32 &= ~(7 << 10);	// SLP_TYP
+	reg32 |= (1 << 0);	// SCI_EN
+	outl(reg32, pmbase + 0x04);
+}
+
+static void gpio_init(struct device *dev)
+{
+	/* This should be done in romstage.c already */
+	pci_write_config32(dev, GPIO_BASE, (GPIOBASE_ADDR | 1));
+	pci_write_config8(dev, GPIO_CNTL, 0x10);
+}
+
+static void i82801dx_rtc_init(struct device *dev)
+{
+	u8 reg8;
+	u32 reg32;
+	int rtc_failed;
+
+	reg8 = pci_read_config8(dev, GEN_PMCON_3);
+	rtc_failed = reg8 & RTC_BATTERY_DEAD;
+	if (rtc_failed) {
+		reg8 &= ~(1 << 1);	/* Preserve the power fail state. */
+		pci_write_config8(dev, GEN_PMCON_3, reg8);
+	}
+	reg32 = pci_read_config32(dev, GEN_STS);
+	rtc_failed |= reg32 & (1 << 2);
+	cmos_init(rtc_failed);
+
+	/* Enable access to the upper 128 byte bank of CMOS RAM. */
+	pci_write_config8(dev, RTC_CONF, 0x04);
+}
+
+static void i82801dx_lpc_route_dma(struct device *dev, u8 mask)
+{
+	u16 reg16;
+	int i;
+
+	reg16 = pci_read_config16(dev, PCI_DMA_CFG);
+	reg16 &= 0x300;
+	for (i = 0; i < 8; i++) {
+		if (i == 4)
+			continue;
+		reg16 |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
+	}
+	pci_write_config16(dev, PCI_DMA_CFG, reg16);
+}
+
+static void i82801dx_lpc_decode_en(struct device *dev)
+{
+	/* Decode 0x3F8-0x3FF (COM1) for COMA port, 0x2F8-0x2FF (COM2) for COMB.
+	 * LPT decode defaults to 0x378-0x37F and 0x778-0x77F.
+	 * Floppy decode defaults to 0x3F0-0x3F5, 0x3F7.
+	 * We also need to set the value for LPC I/F Enables Register.
+	 */
+	pci_write_config8(dev, COM_DEC, 0x10);
+	pci_write_config16(dev, LPC_EN, 0x300F);
+}
+
+/* ICH4 does not mention HPET in the docs, but
+ * all ICH3 and ICH4 do have HPETs built in.
+ */
+static void enable_hpet(struct device *dev)
+{
+	u32 reg32, hpet, val;
+
+	/* Set HPET base address and enable it */
+	printk(BIOS_DEBUG, "Enabling HPET at 0x%x\n", HPET_BASE_ADDRESS);
+	reg32 = pci_read_config32(dev, GEN_CNTL);
+	/*
+	 * Bit 17 is HPET enable bit.
+	 * Bit 16:15 control the HPET base address.
+	 */
+	reg32 &= ~(3 << 15);	/* Clear it */
+
+	hpet = HPET_BASE_ADDRESS >> 12;
+	hpet &= 0x3;
+
+	reg32 |= (hpet << 15);
+	reg32 |= (1 << 17);	/* Enable HPET. */
+	pci_write_config32(dev, GEN_CNTL, reg32);
+
+	/* Check to see whether it took */
+	reg32 = pci_read_config32(dev, GEN_CNTL);
+	val = reg32 >> 15;
+	val &= 0x7;
+
+	if ((val & 0x4) && (hpet == (val & 0x3))) {
+		printk(BIOS_INFO, "HPET enabled at 0x%x\n", HPET_BASE_ADDRESS);
+	} else {
+		printk(BIOS_WARNING, "HPET was not enabled correctly\n");
+		reg32 &= ~(1 << 17);	/* Clear Enable */
+		pci_write_config32(dev, GEN_CNTL, reg32);
+	}
+}
+
+static void lpc_init(struct device *dev)
+{
+	i82801dx_enable_acpi(dev);
+	/* IO APIC initialization. */
+	i82801dx_enable_ioapic(dev);
+
+	i82801dx_enable_serial_irqs(dev);
+
+	/* Setup the PIRQ. */
+	i82801dx_pirq_init(dev);
+
+	/* Setup power options. */
+	i82801dx_power_options(dev);
+
+	/* Set the state of the GPIO lines. */
+	gpio_init(dev);
+
+	/* Initialize the real time clock. */
+	i82801dx_rtc_init(dev);
+
+	/* Route DMA. */
+	i82801dx_lpc_route_dma(dev, 0xff);
+
+	/* Initialize ISA DMA. */
+	isa_dma_init();
+
+	/* Setup decode ports and LPC I/F enables. */
+	i82801dx_lpc_decode_en(dev);
+
+	/* Initialize the High Precision Event Timers */
+	enable_hpet(dev);
+
+	setup_i8259();
+}
+
+static void i82801dx_lpc_read_resources(struct device *dev)
+{
+	struct resource *res;
+
+	/* Get the normal PCI resources of this device. */
+	pci_dev_read_resources(dev);
+
+	/* Add an extra subtractive resource for both memory and I/O. */
+	res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
+	res->base = 0;
+	res->size = 0x1000;
+	res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+		     IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+	res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
+	res->base = 0xff800000;
+	res->size = 0x00800000; /* 8 MB for flash */
+	res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
+		     IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+	res = new_resource(dev, 3); /* IOAPIC */
+	res->base = IO_APIC_ADDR;
+	res->size = 0x00001000;
+	res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+}
+
+static struct device_operations lpc_ops = {
+	.read_resources		= i82801dx_lpc_read_resources,
+	.set_resources		= pci_dev_set_resources,
+	.enable_resources	= pci_dev_enable_resources,
+	.init			= lpc_init,
+	.scan_bus		= scan_static_bus,
+	.enable			= i82801dx_enable,
+};
+
+/* 82801DB/DBL */
+static const struct pci_driver lpc_driver_db __pci_driver = {
+	.ops = &lpc_ops,
+	.vendor = PCI_VID_INTEL,
+	.device = PCI_DID_INTEL_82801DB_LPC,
+};
+
+/* 82801DBM */
+static const struct pci_driver lpc_driver_dbm __pci_driver = {
+	.ops = &lpc_ops,
+	.vendor = PCI_VID_INTEL,
+	.device = PCI_DID_INTEL_82801DBM_LPC,
+};