diff options
Diffstat (limited to 'src/mainboard/google/puff/variants/baseboard/devicetree.cb')
| -rw-r--r-- | src/mainboard/google/puff/variants/baseboard/devicetree.cb | 355 |
1 files changed, 355 insertions, 0 deletions
diff --git a/src/mainboard/google/puff/variants/baseboard/devicetree.cb b/src/mainboard/google/puff/variants/baseboard/devicetree.cb new file mode 100644 index 000000000000..976d82970c8f --- /dev/null +++ b/src/mainboard/google/puff/variants/baseboard/devicetree.cb @@ -0,0 +1,355 @@ +chip soc/intel/cannonlake + + # GPE configuration + # Note that GPE events called out in ASL code rely on this + # route. i.e. If this route changes then the affected GPE + # offset bits also need to be changed. + # DW1 is used by: + # - GPP_C1 - PCIE_14_WLAN_WAKE_ODL + # - GPP_C21 - H1_PCH_INT_ODL + register "gpe0_dw0" = "PMC_GPP_A" + register "gpe0_dw1" = "PMC_GPP_C" + register "gpe0_dw2" = "PMC_GPP_D" + + # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f + register "gen1_dec" = "0x00fc0801" + register "gen2_dec" = "0x000c0201" + # EC memory map range is 0x900-0x9ff + register "gen3_dec" = "0x00fc0901" + + # FSP configuration + register "SkipExtGfxScan" = "1" + register "SataSalpSupport" = "1" + register "SataPortsEnable[1]" = "1" + register "SataPortsDevSlp[1]" = "1" + # Configure devslp pad reset to PLT_RST + register "SataPortsDevSlpResetConfig[1]" = "SataDevSlpPlatformReset" + register "satapwroptimize" = "1" + # Enable System Agent dynamic frequency + register "SaGv" = "SaGv_Enabled" + # Enable S0ix + register "s0ix_enable" = "1" + # Enable DPTF + register "dptf_enable" = "1" + register "power_limits_config" = "{ + .tdp_pl1_override = 15, + .tdp_pl2_override = 64, + }" + register "Device4Enable" = "1" + # Enable eDP device + register "DdiPortEdp" = "1" + # Enable HPD for DDI ports B/C + register "DdiPortBHpd" = "1" + register "DdiPortCHpd" = "1" + register "tcc_offset" = "10" # TCC of 90C + # Unlock GPIO pads + register "PchUnlockGpioPads" = "1" + # SD card WP pin configuration + register "ScsSdCardWpPinEnabled" = "0" + + # NOTE: if any variant wants to override this value, use the same format + # as register "common_soc_config.pch_thermal_trip" = "value", instead of + # putting it under register "common_soc_config" in overridetree.cb file. + register "common_soc_config.pch_thermal_trip" = "77" + + # Select CPU PL2/PL4 config + register "cpu_pl2_4_cfg" = "baseline" + + # VR Settings Configuration for 4 Domains + #+----------------+-------+-------+-------+-------+ + #| Domain/Setting | SA | IA | GTUS | GTS | + #+----------------+-------+-------+-------+-------+ + #| Psi1Threshold | 20A | 20A | 20A | 20A | + #| Psi2Threshold | 5A | 5A | 5A | 5A | + #| Psi3Threshold | 1A | 1A | 1A | 1A | + #| Psi3Enable | 1 | 1 | 1 | 1 | + #| Psi4Enable | 1 | 1 | 1 | 1 | + #| ImonSlope | 0 | 0 | 0 | 0 | + #| ImonOffset | 0 | 0 | 0 | 0 | + #| IccMax | 6A | 70A | 31A | 31A | + #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | + #| AcLoadline | 10.3 | 1.8 | 3.1 | 3.1 | + #| DcLoadline | 10.3 | 1.8 | 3.1 | 3.1 | + #+----------------+-------+-------+-------+-------+ + register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 1030, + .dc_loadline = 1030, + }" + + register "domain_vr_config[VR_IA_CORE]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 180, + .dc_loadline = 180, + }" + + register "domain_vr_config[VR_GT_UNSLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 310, + .dc_loadline = 310, + }" + + register "domain_vr_config[VR_GT_SLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 310, + .dc_loadline = 310, + }" + + register "PchPmSlpS3MinAssert" = "2" # 50ms + register "PchPmSlpS4MinAssert" = "1" # 1s + register "PchPmSlpSusMinAssert" = "1" # 500ms + register "PchPmSlpAMinAssert" = "3" # 98ms + + # NOTE: Duration programmed in the below register should never be smaller than the + # stretch duration programmed in the following registers - + # - GEN_PMCON_A.SLP_S3_MIN_ASST_WDTH (PchPmSlpS3MinAssert) + # - GEN_PMCON_A.S4MAW (PchPmSlpS4MinAssert) + # - PM_CFG.SLP_A_MIN_ASST_WDTH (PchPmSlpAMinAssert) + # - PM_CFG.SLP_LAN_MIN_ASST_WDTH + register "PchPmPwrCycDur" = "1" # 1s + + # Enable Audio DSP oscillator qualification for S0ix + register "cppmvric2_adsposcdis" = "1" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port 0 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port 1 + register "usb2_ports[2]" = "USB2_PORT_SHORT(OC3)" # Type-A Port 0 + register "usb2_ports[3]" = "USB2_PORT_LONG(OC3)" # Type-A Port 1 + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # WWAN + register "usb2_ports[6]" = "USB2_PORT_LONG(OC_SKIP)" # Camera + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # BT + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 0 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 1 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 0 + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 1 + register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC_SKIP)" # WWAN + + # Enable Root port 9(x4) for NVMe. + register "PcieRpEnable[8]" = "1" + register "PcieRpLtrEnable[8]" = "1" + # RP 9 uses CLK SRC 1 + register "PcieClkSrcUsage[1]" = "8" + # ClkReq-to-ClkSrc mapping for CLK SRC 1 + register "PcieClkSrcClkReq[1]" = "1" + + # PCIe port 14 for M.2 E-key WLAN + register "PcieRpEnable[13]" = "1" + register "PcieRpLtrEnable[13]" = "1" + # RP 14 uses CLK SRC 3 + register "PcieClkSrcUsage[3]" = "13" + register "PcieClkSrcClkReq[3]" = "3" + + #Enable I2S Audio, SSP0, SSP1 and DMIC0, default DMIC1 N/A (by variants override) + register "PchHdaDspEnable" = "1" + register "PchHdaAudioLinkSsp0" = "1" + register "PchHdaAudioLinkSsp1" = "1" + register "PchHdaAudioLinkDmic0" = "1" + register "PchHdaAudioLinkDmic1" = "0" + + # GPIO PM programming + register "gpio_override_pm" = "1" + + # GPIO community PM configuration + # Disable dynamic clock gating; with bits 0-5 set in these registers, + # some short interrupt pulses were missed (esp. cr50 irq) + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + + device cpu_cluster 0 on + device lapic 0 on end + end + + device domain 0 on + device pci 00.0 on end # Host Bridge + device pci 02.0 on end # Integrated Graphics Device + device pci 04.0 off end # SA Thermal device + device pci 05.0 off end # SA IPU + device pci 12.0 on end # Thermal Subsystem + device pci 12.5 off end # UFS SCS + device pci 12.6 off end # GSPI #2 + device pci 14.0 on + chip drivers/usb/acpi + register "desc" = ""Root Hub"" + register "type" = "UPC_TYPE_HUB" + device usb 0.0 on + chip drivers/usb/acpi + register "desc" = ""Left Type-C Port"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 2.0 on end + end + chip drivers/usb/acpi + register "desc" = ""Right Type-C Port 1"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device usb 2.1 on end + end + chip drivers/usb/acpi + register "desc" = ""Left Type-A Port"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 2.2 on end + end + chip drivers/usb/acpi + register "desc" = ""Right Type-A Port 1"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(2, 2)" + device usb 2.3 on end + end + chip drivers/usb/acpi + register "desc" = ""WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device usb 2.5 on end + end + chip drivers/usb/acpi + register "desc" = ""Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device usb 2.6 on end + end + chip drivers/usb/acpi + register "desc" = ""Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C14)" + device usb 2.9 on end + end + chip drivers/usb/acpi + register "desc" = ""Left Type-C Port"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 3.0 on end + end + chip drivers/usb/acpi + register "desc" = ""Right Type-C Port 1"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device usb 3.1 on end + end + chip drivers/usb/acpi + register "desc" = ""Left Type-A Port"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 3.2 on end + end + chip drivers/usb/acpi + register "desc" = ""Right Type-A Port 1"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(2, 2)" + device usb 3.3 on end + end + chip drivers/usb/acpi + register "desc" = ""WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device usb 3.4 on end + end + end + end + end # USB xHCI + device pci 14.1 off end # USB xDCI (OTG) + device pci 14.3 on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end # CNVi wifi + device pci 14.5 on end # SDCard + device pci 15.0 on end # I2C #0 + device pci 15.1 on end # I2C #1 + device pci 15.2 on end # I2C #2 + device pci 15.3 on end # I2C #3 + device pci 16.0 on end # Management Engine Interface 1 + device pci 16.1 off end # Management Engine Interface 2 + device pci 16.2 off end # Management Engine IDE-R + device pci 16.3 off end # Management Engine KT Redirection + device pci 16.4 off end # Management Engine Interface 3 + device pci 16.5 off end # Management Engine Interface 4 + device pci 17.0 on end # SATA + device pci 19.0 on end # I2C #4 + device pci 19.1 off end # I2C #5 + device pci 19.2 off end # UART #2 + device pci 1a.0 off end # eMMC + device pci 1c.0 off end # PCI Express Port 1 (USB) + device pci 1c.1 off end # PCI Express Port 2 (USB) + device pci 1c.2 off end # PCI Express Port 3 (USB) + device pci 1c.3 off end # PCI Express Port 4 (USB) + device pci 1c.4 off end # PCI Express Port 5 (USB) + device pci 1c.5 off end # PCI Express Port 6 + device pci 1c.6 off end # PCI Express Port 7 + device pci 1c.7 off end # PCI Express Port 8 + device pci 1d.0 on # PCI Express Port 9 (X4 NVME) + register "PcieRpSlotImplemented[8]" = "1" + end + device pci 1d.1 off end # PCI Express Port 10 + device pci 1d.2 off end # PCI Express Port 11 + device pci 1d.3 off end # PCI Express Port 12 + device pci 1d.4 off end # PCI Express port 13 + device pci 1d.5 on + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_01" + device pci 00.0 on end + end + register "PcieRpSlotImplemented[13]" = "1" + end # PCI Express Port 14 (x4) + device pci 1e.0 on end # UART #0 + device pci 1e.1 off end # UART #1 + device pci 1e.2 on + chip drivers/spi/acpi + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "compat_string" = ""google,cr50"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_C21_IRQ)" + device spi 0 on end + end + end # GSPI #0 + device pci 1e.3 on end # GSPI #1 + device pci 1f.0 on + chip ec/google/chromeec + device pnp 0c09.0 on end + end + end # eSPI Interface + device pci 1f.1 on end # P2SB + device pci 1f.2 hidden end # Power Management Controller + device pci 1f.3 on end # Intel HDA + device pci 1f.4 on end # SMBus + device pci 1f.5 on end # PCH SPI + device pci 1f.6 off end # GbE + end +end |