1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <stdint.h>
#include <console/console.h>
#include <northbridge/intel/sandybridge/sandybridge.h>
#include <northbridge/intel/sandybridge/raminit.h>
#include <southbridge/intel/bd82x6x/pch.h>
#include <southbridge/intel/common/gpio.h>
#include <bootmode.h>
#include <ec/quanta/it8518/ec.h>
#include "ec.h"
#include "onboard.h"
void mainboard_late_rcba_config(void)
{
/*
* GFX INTA -> PIRQA (MSI)
* D20IP_XHCI XHCI INTA -> PIRQD (MSI)
* D26IP_E2P EHCI #2 INTA -> PIRQF
* D27IP_ZIP HDA INTA -> PIRQA (MSI)
* D28IP_P2IP WLAN INTA -> PIRQD
* D28IP_P3IP Card Reader INTB -> PIRQE
* D28IP_P6IP LAN INTC -> PIRQB
* D29IP_E1P EHCI #1 INTA -> PIRQD
* D31IP_SIP SATA INTA -> PIRQB (MSI)
* D31IP_SMIP SMBUS INTB -> PIRQH
*/
/* Device interrupt pin register (board specific) */
RCBA32(D31IP) = (NOINT << D31IP_TTIP) | (NOINT << D31IP_SIP2) |
(INTB << D31IP_SMIP) | (INTA << D31IP_SIP);
RCBA32(D30IP) = (NOINT << D30IP_PIP);
RCBA32(D29IP) = (INTA << D29IP_E1P);
RCBA32(D28IP) = (NOINT << D28IP_P1IP) | (INTA << D28IP_P2IP) |
(INTB << D28IP_P3IP) | (NOINT << D28IP_P4IP) |
(NOINT << D28IP_P5IP) | (INTC << D28IP_P6IP) |
(NOINT << D28IP_P7IP) | (NOINT << D28IP_P8IP);
RCBA32(D27IP) = (INTA << D27IP_ZIP);
RCBA32(D26IP) = (INTA << D26IP_E2P);
RCBA32(D25IP) = (NOINT << D25IP_LIP);
RCBA32(D22IP) = (NOINT << D22IP_MEI1IP);
RCBA32(D20IP) = (INTA << D20IP_XHCIIP);
/* Device interrupt route registers */
DIR_ROUTE(D31IR, PIRQB, PIRQH, PIRQA, PIRQC);
DIR_ROUTE(D29IR, PIRQD, PIRQE, PIRQF, PIRQG);
DIR_ROUTE(D28IR, PIRQD, PIRQE, PIRQB, PIRQC);
DIR_ROUTE(D27IR, PIRQA, PIRQB, PIRQC, PIRQD);
DIR_ROUTE(D26IR, PIRQF, PIRQB, PIRQC, PIRQD);
DIR_ROUTE(D25IR, PIRQA, PIRQB, PIRQC, PIRQD);
DIR_ROUTE(D22IR, PIRQA, PIRQB, PIRQC, PIRQD);
DIR_ROUTE(D20IR, PIRQD, PIRQE, PIRQF, PIRQG);
}
/*
* The Stout EC needs to be reset to RW mode. It is important that
* the RTC_PWR_STS is not set until ramstage EC init.
*/
static void early_ec_init(void)
{
u8 ec_status = ec_read(EC_STATUS_REG);
int rec_mode = get_recovery_mode_switch();
if (((ec_status & 0x3) == EC_IN_RO_MODE) ||
((ec_status & 0x3) == EC_IN_RECOVERY_MODE)) {
printk(BIOS_DEBUG, "EC Cold Boot Detected\n");
if (!rec_mode) {
/*
* Tell EC to exit RO mode
*/
printk(BIOS_DEBUG, "EC will exit RO mode and boot normally\n");
ec_write_cmd(EC_CMD_EXIT_BOOT_BLOCK);
die("wait for ec to reset");
}
} else {
printk(BIOS_DEBUG, "EC Warm Boot Detected\n");
ec_write_cmd(EC_CMD_WARM_RESET);
}
}
void mainboard_fill_pei_data(struct pei_data *pei_data)
{
/* TODO: Confirm if nortbridge_fill_pei_data() gets .system_type right (should be 0) */
}
void mainboard_early_init(int s3resume)
{
/* Do ec reset as early as possible, but skip it on S3 resume */
if (!s3resume) {
early_ec_init();
}
}
const struct southbridge_usb_port mainboard_usb_ports[] = {
/* enabled USB oc pin length */
{1, 0, 0}, /* P0: USB 3.0 1 (OC0) */
{1, 0, 0}, /* P1: USB 3.0 2 (OC0) */
{0, 0, 0}, /* P2: Empty */
{1, 0, -1}, /* P3: Camera (no OC) */
{1, 0, -1}, /* P4: WLAN (no OC) */
{1, 0, -1}, /* P5: WWAN (no OC) */
{0, 0, 0}, /* P6: Empty */
{0, 0, 0}, /* P7: Empty */
{0, 0, 0}, /* P8: Empty */
{1, 0, 4}, /* P9: USB 2.0 (AUO4) (OC4) */
{0, 0, 0}, /* P10: Empty */
{0, 0, 0}, /* P11: Empty */
{0, 0, 0}, /* P12: Empty */
{1, 0, -1}, /* P13: Bluetooth (no OC) */
};
|
