blob: b06f4bc0a64e89d1fdcf54d0ecee8a85525bcc52 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
|
# SPDX-License-Identifier: GPL-2.0-or-later
chip soc/amd/picasso
# Start : OPN Performance Configuration
# See devhub #55593 Chapter 3.2 for documentation
# For the below fields, 0 indicates use SOC default
# System config index
register "system_config" = "2"
# Set STAPM confiuration. All of these fields must be set >0 to take affect
register "slow_ppt_limit" = "20000" #mw
register "fast_ppt_limit" = "24000" #mw
register "slow_ppt_time_constant" = "5" #second
register "stapm_time_constant" = "200" #second
register "sustained_power_limit" = "12000" #mw
register "telemetry_vddcr_vdd_slope" = "62413" #mA
register "telemetry_vddcr_vdd_offset" = "0"
register "telemetry_vddcr_soc_slope" = "28977" #mA
register "telemetry_vddcr_soc_offset" = "0"
# End : OPN Performance Configuration
# USB OC pin mapping
register "usb_port_overcurrent_pin[0]" = "USB_OC_PIN_0" # USB C0
register "usb_port_overcurrent_pin[1]" = "USB_OC_PIN_0" # USB A0
register "usb_port_overcurrent_pin[2]" = "USB_OC_PIN_1" # USB A1
register "usb_port_overcurrent_pin[3]" = "USB_OC_PIN_1" # USB C1
register "xhci0_force_gen1" = "1"
# Enable I2C2 for trackpad, touchscreen, pen at 400kHz
register "i2c[2]" = "{
.speed = I2C_SPEED_FAST,
.rise_time_ns = 3,
.fall_time_ns = 2,
}"
# Enable I2C3 for H1 400kHz
register "i2c[3]" = "{
.speed = I2C_SPEED_FAST,
.rise_time_ns = 16,
.fall_time_ns = 8,
.early_init = true,
}"
# See AMD 55570-B1 Table 13: PCI Device ID Assignments.
device domain 0 on
subsystemid 0x1022 0x1510 inherit
end # domain
device mmio 0xfedc4000 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_9)"
register "wake" = "GEVENT_22"
register "probed" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""PNP0C50""
register "generic.desc" = ""Synaptics Touchpad""
register "generic.irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_9)"
register "generic.wake" = "GEVENT_22"
register "generic.probed" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2c on end
end
chip drivers/i2c/generic
register "hid" = ""RAYD0001""
register "desc" = ""Raydium Touchscreen""
register "probed" = "1"
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_12)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)"
# 32ms: Rise time of the reset line
# 20ms: Firmware ready time
register "reset_delay_ms" = "32 + 20"
register "has_power_resource" = "1"
register "disable_gpio_export_in_crs" = "1"
device i2c 39 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""ELAN9004""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.probed" = "1"
register "generic.irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_12)"
register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)"
register "generic.reset_delay_ms" = "20"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 10 on end
end
end
end # chip soc/amd/picasso
|
