1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootstate.h>
#include <console/console.h>
#include <device/pci_ids.h>
#include <device/pci_ops.h>
#include <gpio.h>
#include <hwilib.h>
#include <intelblocks/lpc_lib.h>
#include <intelblocks/pcr.h>
#include <soc/pcr_ids.h>
#include <timer.h>
#include <timestamp.h>
#include <baseboard/variants.h>
#include <types.h>
#define TX_DWORD3 0xa8c
void variant_mainboard_final(void)
{
struct device *dev = NULL;
/*
* PIR6 register mapping for PCIe root ports
* INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#-> PIRQA#
*/
pcr_write16(PID_ITSS, 0x314c, 0x0321);
/* Disable clock outputs 1-5 (CLKOUT) for XIO2001 PCIe to PCI Bridge. */
dev = dev_find_device(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2001, 0);
if (dev)
pci_write_config8(dev, 0xd8, 0x3e);
/* Enable CLKRUN_EN for power gating LPC */
lpc_enable_pci_clk_cntl();
/*
* Enable LPC PCE (Power Control Enable) by setting IOSF-SB port 0xD2
* offset 0x341D bit3 and bit0.
* Enable LPC CCE (Clock Control Enable) by setting IOSF-SB port 0xD2
* offset 0x341C bit [3:0].
*/
pcr_or32(PID_LPC, PCR_LPC_PRC, (PCR_LPC_CCE_EN | PCR_LPC_PCE_EN));
/*
* Correct the SATA transmit signal via the High Speed I/O Transmit
* Control Register 3.
* Bit [23:16] set the output voltage swing for TX line.
* The value 0x4a sets the swing level to 0.58 V.
*/
pcr_rmw32(PID_MODPHY, TX_DWORD3, (0x00 << 16), (0x4a << 16));
}
static void wait_for_legacy_dev(void *unused)
{
uint32_t legacy_delay, us_since_boot;
struct stopwatch sw;
/* Open main hwinfo block. */
if (hwilib_find_blocks("hwinfo.hex") != CB_SUCCESS)
return;
/* Get legacy delay parameter from hwinfo. */
if (hwilib_get_field(LegacyDelay, (uint8_t *) &legacy_delay,
sizeof(legacy_delay)) != sizeof(legacy_delay))
return;
us_since_boot = get_us_since_boot();
/* No need to wait if the time since boot is already long enough.*/
if (us_since_boot > legacy_delay)
return;
stopwatch_init_msecs_expire(&sw, (legacy_delay - us_since_boot) / 1000);
printk(BIOS_NOTICE, "Wait remaining %d of %d us for legacy devices...",
legacy_delay - us_since_boot, legacy_delay);
stopwatch_wait_until_expired(&sw);
printk(BIOS_NOTICE, "done!\n");
}
static void finalize_boot(void *unused)
{
/* Set coreboot ready LED. */
gpio_output(CNV_RGI_DT, 1);
}
BOOT_STATE_INIT_ENTRY(BS_DEV_ENUMERATE, BS_ON_ENTRY, wait_for_legacy_dev, NULL);
BOOT_STATE_INIT_ENTRY(BS_PAYLOAD_BOOT, BS_ON_ENTRY, finalize_boot, NULL);
|
