1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
/* SPDX-License-Identifier: GPL-2.0-only */
/* This file is part of the coreboot project. */
#include <bootstate.h>
#include <console/console.h>
#include <device/mmio.h>
#include <device/device.h>
#include <intelblocks/pmc.h>
#include <intelblocks/pmclib.h>
#include <intelblocks/rtc.h>
#include <soc/pci_devs.h>
#include <soc/pm.h>
#include "chip.h"
/*
* Set which power state system will be after reapplying
* the power (from G3 State)
*/
void pmc_soc_set_afterg3_en(const bool on)
{
uint8_t reg8;
uint8_t *const pmcbase = pmc_mmio_regs();
reg8 = read8(pmcbase + GEN_PMCON_A);
if (on)
reg8 &= ~SLEEP_AFTER_POWER_FAIL;
else
reg8 |= SLEEP_AFTER_POWER_FAIL;
write8(pmcbase + GEN_PMCON_A, reg8);
}
static void pm1_enable_pwrbtn_smi(void *unused)
{
/*
* Enable power button SMI only before jumping to payload. This ensures
* that:
* 1. Power button SMI is enabled only after coreboot is done.
* 2. On resume path, power button SMI is not enabled and thus avoids
* any shutdowns because of power button presses due to power button
* press in resume path.
*/
pmc_update_pm1_enable(PWRBTN_EN);
}
BOOT_STATE_INIT_ENTRY(BS_PAYLOAD_LOAD, BS_ON_EXIT, pm1_enable_pwrbtn_smi, NULL);
static void config_deep_sX(uint32_t offset, uint32_t mask, int sx, int enable)
{
uint32_t reg;
uint8_t *pmcbase = pmc_mmio_regs();
printk(BIOS_DEBUG, "%sabling Deep S%c\n",
enable ? "En" : "Dis", sx + '0');
reg = read32(pmcbase + offset);
if (enable)
reg |= mask;
else
reg &= ~mask;
write32(pmcbase + offset, reg);
}
static void config_deep_s5(int on_ac, int on_dc)
{
/* Treat S4 the same as S5. */
config_deep_sX(S4_PWRGATE_POL, S4AC_GATE_SUS, 4, on_ac);
config_deep_sX(S4_PWRGATE_POL, S4DC_GATE_SUS, 4, on_dc);
config_deep_sX(S5_PWRGATE_POL, S5AC_GATE_SUS, 5, on_ac);
config_deep_sX(S5_PWRGATE_POL, S5DC_GATE_SUS, 5, on_dc);
}
static void config_deep_s3(int on_ac, int on_dc)
{
config_deep_sX(S3_PWRGATE_POL, S3AC_GATE_SUS, 3, on_ac);
config_deep_sX(S3_PWRGATE_POL, S3DC_GATE_SUS, 3, on_dc);
}
static void config_deep_sx(uint32_t deepsx_config)
{
uint32_t reg;
uint8_t *pmcbase = pmc_mmio_regs();
reg = read32(pmcbase + DSX_CFG);
reg &= ~DSX_CFG_MASK;
reg |= deepsx_config;
write32(pmcbase + DSX_CFG, reg);
}
static void pmc_init(void *unused)
{
const config_t *config = config_of_soc();
rtc_init();
pmc_set_power_failure_state(true);
pmc_gpe_init();
config_deep_s3(config->deep_s3_enable_ac, config->deep_s3_enable_dc);
config_deep_s5(config->deep_s5_enable_ac, config->deep_s5_enable_dc);
config_deep_sx(config->deep_sx_config);
}
/*
* Initialize PMC controller.
*
* PMC controller gets hidden from PCI bus during FSP-Silicon init call.
* Hence PCI enumeration can't be used to initialize bus device and
* allocate resources.
*/
BOOT_STATE_INIT_ENTRY(BS_DEV_INIT_CHIPS, BS_ON_EXIT, pmc_init, NULL);
static void soc_acpi_mode_init(void *unused)
{
/*
* PMC initialization happens earlier for this SoC because FSP-Silicon
* init hides PMC from PCI bus. However, pmc_set_acpi_mode, which
* disables ACPI mode doesn't need to happen that early and can be
* delayed till typical BS_DEV_INIT. This ensures that ACPI mode
* disabling happens the same way for all SoCs and hence the ordering of
* events is the same.
*
* This is important to ensure that the ordering does not break the
* assumptions of any other drivers (e.g. ChromeEC) which could be
* taking different actions based on disabling of ACPI (e.g. flushing of
* all EC hostevent bits).
*
* P.S.: This cannot be done as part of pmc_soc_init as PMC device is
* hidden and hence the PMC driver never gets enumerated and so init is
* not called for it.
*/
pmc_set_acpi_mode();
}
BOOT_STATE_INIT_ENTRY(BS_DEV_INIT, BS_ON_EXIT, soc_acpi_mode_init, NULL);
|
