1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
/* SPDX-License-Identifier: GPL-2.0-only */
#ifndef INTEL_LYNXPOINT_LP_GPIO_H
#define INTEL_LYNXPOINT_LP_GPIO_H
/* LynxPoint LP GPIOBASE Registers */
#define GPIO_OWNER(set) (0x00 + ((set) * 4))
#define GPIO_PIRQ_APIC_EN 0x10
#define GPIO_BLINK 0x18
#define GPIO_SER_BLINK 0x1c
#define GPIO_SER_BLINK_CS 0x20
#define GPIO_SER_BLINK_DATA 0x24
#define GPIO_ROUTE(set) (0x30 + ((set) * 4))
#define GPIO_RESET(set) (0x60 + ((set) * 4))
#define GPIO_GLOBAL_CONFIG 0x7c
#define GPIO_IRQ_IS(set) (0x80 + ((set) * 4))
#define GPIO_IRQ_IE(set) (0x90 + ((set) * 4))
#define GPIO_CONFIG0(gpio) (0x100 + ((gpio) * 8))
#define GPIO_CONFIG1(gpio) (0x104 + ((gpio) * 8))
#define MAX_GPIO_NUMBER 94 /* zero based */
#define GPIO_LIST_END 0xffffffff
/* conf0 */
#define GPIO_MODE_NATIVE (0 << 0)
#define GPIO_MODE_GPIO (1 << 0)
#define GPIO_DIR_OUTPUT (0 << 2)
#define GPIO_DIR_INPUT (1 << 2)
#define GPIO_NO_INVERT (0 << 3)
#define GPIO_INVERT (1 << 3)
#define GPIO_IRQ_EDGE (0 << 4)
#define GPIO_IRQ_LEVEL (1 << 4)
#define GPI_LEVEL (1 << 30)
#define GPO_LEVEL_SHIFT 31
#define GPO_LEVEL_MASK (1UL << GPO_LEVEL_SHIFT)
#define GPO_LEVEL_LOW (0UL << GPO_LEVEL_SHIFT)
#define GPO_LEVEL_HIGH (1UL << GPO_LEVEL_SHIFT)
/* conf1 */
#define GPIO_PULL_NONE (0 << 0)
#define GPIO_PULL_DOWN (1 << 0)
#define GPIO_PULL_UP (2 << 0)
#define GPIO_SENSE_ENABLE (0 << 2)
#define GPIO_SENSE_DISABLE (1 << 2)
/* owner */
#define GPIO_OWNER_ACPI 0
#define GPIO_OWNER_GPIO 1
/* route */
#define GPIO_ROUTE_SCI 0
#define GPIO_ROUTE_SMI 1
/* irqen */
#define GPIO_IRQ_DISABLE 0
#define GPIO_IRQ_ENABLE 1
/* blink */
#define GPO_NO_BLINK 0
#define GPO_BLINK 1
/* reset */
#define GPIO_RESET_PWROK 0
#define GPIO_RESET_RSMRST 1
/* pirq route to io-apic */
#define GPIO_PIRQ_APIC_MASK 0
#define GPIO_PIRQ_APIC_ROUTE 1
#define LP_GPIO_END \
{ .conf0 = GPIO_LIST_END }
#define LP_GPIO_NATIVE \
{ .conf0 = GPIO_MODE_NATIVE }
#define LP_GPIO_UNUSED \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT, \
.owner = GPIO_OWNER_GPIO, \
.conf1 = GPIO_SENSE_DISABLE }
#define LP_GPIO_ACPI_SCI \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT, \
.owner = GPIO_OWNER_ACPI, \
.route = GPIO_ROUTE_SCI }
#define LP_GPIO_ACPI_SMI \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT, \
.owner = GPIO_OWNER_ACPI, \
.route = GPIO_ROUTE_SMI }
#define LP_GPIO_INPUT \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT, \
.owner = GPIO_OWNER_GPIO }
#define LP_GPIO_INPUT_INVERT \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT, \
.owner = GPIO_OWNER_GPIO }
#define LP_GPIO_IRQ_EDGE \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_EDGE, \
.owner = GPIO_OWNER_GPIO, \
.irqen = GPIO_IRQ_ENABLE }
#define LP_GPIO_IRQ_LEVEL \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL, \
.owner = GPIO_OWNER_GPIO, \
.irqen = GPIO_IRQ_ENABLE }
#define LP_GPIO_PIRQ \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT, \
.owner = GPIO_OWNER_GPIO, \
.pirq = GPIO_PIRQ_APIC_ROUTE }
#define LP_GPIO_OUT_HIGH \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_OUTPUT | GPO_LEVEL_HIGH, \
.owner = GPIO_OWNER_GPIO, \
.conf1 = GPIO_SENSE_DISABLE }
#define LP_GPIO_OUT_LOW \
{ .conf0 = GPIO_MODE_GPIO | GPIO_DIR_OUTPUT | GPO_LEVEL_LOW, \
.owner = GPIO_OWNER_GPIO, \
.conf1 = GPIO_SENSE_DISABLE }
struct pch_lp_gpio_map {
u8 gpio;
u32 conf0;
u32 conf1;
u8 owner;
u8 route;
u8 irqen;
u8 reset;
u8 blink;
u8 pirq;
} __packed;
/* Configure GPIOs with mainboard provided settings */
void setup_pch_lp_gpios(const struct pch_lp_gpio_map map[]);
/* get GPIO pin value */
int get_gpio(int gpio_num);
/*
* get a number comprised of multiple GPIO values. gpio_num_array points to
* the array of gpio pin numbers to scan, terminated by -1.
*/
unsigned int get_gpios(const int *gpio_num_array);
void set_gpio(int gpio_num, int value);
int gpio_is_native(int gpio_num);
#endif
|
