path: root/src/vendorcode/intel/fsp/fsp2_0/alderlake/FspsUpd.h

/** @file

Copyright (c) 2021, Intel Corporation. All rights reserved.<BR>

Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this
  list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
  list of conditions and the following disclaimer in the documentation and/or
  other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
  be used to endorse or promote products derived from this software without
  specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  THE POSSIBILITY OF SUCH DAMAGE.

  This file is automatically generated. Please do NOT modify !!!

**/

#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__

#include <FspUpd.h>

#pragma pack(1)


///
/// Azalia Header structure
///
typedef struct {
  UINT16 VendorId;           ///< Codec Vendor ID
  UINT16 DeviceId;           ///< Codec Device ID
  UINT8  RevisionId;         ///< Revision ID of the codec. 0xFF matches any revision.
  UINT8  SdiNum;             ///< SDI number, 0xFF matches any SDI.
  UINT16 DataDwords;         ///< Number of data DWORDs pointed by the codec data buffer.
  UINT32 Reserved;           ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;

///
/// Audio Azalia Verb Table structure
///
typedef struct {
  AZALIA_HEADER Header;      ///< AZALIA PCH header
  UINT32        *Data;       ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;

///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
  SiPchNoInt,        ///< No Interrupt Pin
  SiPchIntA,
  SiPchIntB,
  SiPchIntC,
  SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
  UINT8        Device;                  ///< Device number
  UINT8        Function;                ///< Device function
  UINT8        IntX;                    ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
  UINT8        Irq;                     ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;

#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG  64       ///< Number of all PCH devices


/** Fsp S Configuration
**/
typedef struct {

/** Offset 0x0040 - Logo Pointer
  Points to PEI Display Logo Image
**/
  UINT32                      LogoPtr;

/** Offset 0x0044 - Logo Size
  Size of PEI Display Logo Image
**/
  UINT32                      LogoSize;

/** Offset 0x0048 - Blt Buffer Address
  Address of Blt buffer
**/
  UINT32                      BltBufferAddress;

/** Offset 0x004C - Blt Buffer Size
  Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
  EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
  UINT32                      BltBufferSize;

/** Offset 0x0050 - Graphics Configuration Ptr
  Points to VBT
**/
  UINT32                      GraphicsConfigPtr;

/** Offset 0x0054 - Enable Device 4
  Enable/disable Device 4
  $EN_DIS
**/
  UINT8                       Device4Enable;

/** Offset 0x0055 - Show SPI controller
  Enable/disable to show SPI controller.
  $EN_DIS
**/
  UINT8                       ShowSpiController;

/** Offset 0x0056 - Reserved
**/
  UINT8                       Reserved0[2];

/** Offset 0x0058 - MicrocodeRegionBase
  Memory Base of Microcode Updates
**/
  UINT32                      MicrocodeRegionBase;

/** Offset 0x005C - MicrocodeRegionSize
  Size of Microcode Updates
**/
  UINT32                      MicrocodeRegionSize;

/** Offset 0x0060 - Turbo Mode
  Enable/Disable Turbo mode. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       TurboMode;

/** Offset 0x0061 - Enable SATA SALP Support
  Enable/disable SATA Aggressive Link Power Management.
  $EN_DIS
**/
  UINT8                       SataSalpSupport;

/** Offset 0x0062 - Enable SATA ports
  Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
  and so on.
**/
  UINT8                       SataPortsEnable[8];

/** Offset 0x006A - Enable SATA DEVSLP Feature
  Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
  port, byte0 for port0, byte1 for port1, and so on.
**/
  UINT8                       SataPortsDevSlp[8];

/** Offset 0x0072 - Reserved
**/
  UINT8                       Reserved1[34];

/** Offset 0x0094 - Enable USB2 ports
  Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb20Enable[16];

/** Offset 0x00A4 - Enable USB3 ports
  Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb30Enable[10];

/** Offset 0x00AE - Enable xDCI controller
  Enable/disable to xDCI controller.
  $EN_DIS
**/
  UINT8                       XdciEnable;

/** Offset 0x00AF - Reserved
**/
  UINT8                       Reserved2;

/** Offset 0x00B0 - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
  The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
  UINT32                      DevIntConfigPtr;

/** Offset 0x00B4 - Number of DevIntConfig Entry
  Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
  must not be NULL.
**/
  UINT8                       NumOfDevIntConfig;

/** Offset 0x00B5 - PIRQx to IRQx Map Config
  PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
  PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
  8259 PCI mode.
**/
  UINT8                       PxRcConfig[8];

/** Offset 0x00BD - Select GPIO IRQ Route
  GPIO IRQ Select. The valid value is 14 or 15.
**/
  UINT8                       GpioIrqRoute;

/** Offset 0x00BE - Select SciIrqSelect
  SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
  UINT8                       SciIrqSelect;

/** Offset 0x00BF - Select TcoIrqSelect
  TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
  UINT8                       TcoIrqSelect;

/** Offset 0x00C0 - Enable/Disable Tco IRQ
  Enable/disable TCO IRQ
  $EN_DIS
**/
  UINT8                       TcoIrqEnable;

/** Offset 0x00C1 - PCH HDA Verb Table Entry Number
  Number of Entries in Verb Table.
**/
  UINT8                       PchHdaVerbTableEntryNum;

/** Offset 0x00C2 - Reserved
**/
  UINT8                       Reserved3[2];

/** Offset 0x00C4 - PCH HDA Verb Table Pointer
  Pointer to Array of pointers to Verb Table.
**/
  UINT32                      PchHdaVerbTablePtr;

/** Offset 0x00C8 - PCH HDA Codec Sx Wake Capability
  Capability to detect wake initiated by a codec in Sx
**/
  UINT8                       PchHdaCodecSxWakeCapability;

/** Offset 0x00C9 - Enable SATA
  Enable/disable SATA controller.
  $EN_DIS
**/
  UINT8                       SataEnable;

/** Offset 0x00CA - SATA Mode
  Select SATA controller working mode.
  0:AHCI, 1:RAID
**/
  UINT8                       SataMode;

/** Offset 0x00CB - SPIn Device Mode
  Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
  modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
  UINT8                       SerialIoSpiMode[7];

/** Offset 0x00D2 - SPI<N> Chip Select Polarity
  Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
  1:SerialIoSpiCsActiveHigh
**/
  UINT8                       SerialIoSpiCsPolarity[14];

/** Offset 0x00E0 - SPI<N> Chip Select Enable
  0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
  UINT8                       SerialIoSpiCsEnable[14];

/** Offset 0x00EE - SPIn Default Chip Select Output
  Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available
  options: 0:CS0, 1:CS1
**/
  UINT8                       SerialIoSpiDefaultCsOutput[7];

/** Offset 0x00F5 - SPIn Default Chip Select Mode HW/SW
  Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
  SPI1, ... Available options: 0:HW, 1:SW
**/
  UINT8                       SerialIoSpiCsMode[7];

/** Offset 0x00FC - SPIn Default Chip Select State Low/High
  Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
  Available options: 0:Low, 1:High
**/
  UINT8                       SerialIoSpiCsState[7];

/** Offset 0x0103 - UARTn Device Mode
  Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
  modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
  4:SerialIoUartSkipInit
**/
  UINT8                       SerialIoUartMode[7];

/** Offset 0x010A - Reserved
**/
  UINT8                       Reserved4[2];

/** Offset 0x010C - Default BaudRate for each Serial IO UART
  Set default BaudRate Supported from 0 - default to 6000000
**/
  UINT32                      SerialIoUartBaudRate[7];

/** Offset 0x0128 - Default ParityType for each Serial IO UART
  Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
  UINT8                       SerialIoUartParity[7];

/** Offset 0x012F - Default DataBits for each Serial IO UART
  Set default word length. 0: Default, 5,6,7,8
**/
  UINT8                       SerialIoUartDataBits[7];

/** Offset 0x0136 - Default StopBits for each Serial IO UART
  Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3:
  TwoStopBits
**/
  UINT8                       SerialIoUartStopBits[7];

/** Offset 0x013D - Power Gating mode for each Serial IO UART that works in COM mode
  Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto
**/
  UINT8                       SerialIoUartPowerGating[7];

/** Offset 0x0144 - Enable Dma for each Serial IO UART that supports it
  Set DMA/PIO mode. 0: Disabled, 1: Enabled
**/
  UINT8                       SerialIoUartDmaEnable[7];

/** Offset 0x014B - Enables UART hardware flow control, CTS and RTS lines
  Enables UART hardware flow control, CTS and RTS lines.
**/
  UINT8                       SerialIoUartAutoFlow[7];

/** Offset 0x0152 - Reserved
**/
  UINT8                       Reserved5[2];

/** Offset 0x0154 - SerialIoUartRtsPinMuxPolicy
  Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
  for possible values.
**/
  UINT32                      SerialIoUartRtsPinMuxPolicy[7];

/** Offset 0x0170 - SerialIoUartCtsPinMuxPolicy
  Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
  for possible values.
**/
  UINT32                      SerialIoUartCtsPinMuxPolicy[7];

/** Offset 0x018C - SerialIoUartRxPinMuxPolicy
  Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for
  possible values.
**/
  UINT32                      SerialIoUartRxPinMuxPolicy[7];

/** Offset 0x01A8 - SerialIoUartTxPinMuxPolicy
  Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for
  possible values.
**/
  UINT32                      SerialIoUartTxPinMuxPolicy[7];

/** Offset 0x01C4 - UART Number For Debug Purpose
  UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5,
  6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used
  for debug purpose.
   0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6
**/
  UINT8                       SerialIoDebugUartNumber;

/** Offset 0x01C5 - Serial IO UART DBG2 table
  Enable or disable Serial Io UART DBG2 table, default is Disable; <b>0: Disable;</b>
  1: Enable.
**/
  UINT8                       SerialIoUartDbg2[7];

/** Offset 0x01CC - I2Cn Device Mode
  Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
  modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
  UINT8                       SerialIoI2cMode[8];

/** Offset 0x01D4 - Serial IO I2C SDA Pin Muxing
  Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSdaPinMux[8];

/** Offset 0x01F4 - Serial IO I2C SCL Pin Muxing
  Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSclPinMux[8];

/** Offset 0x0214 - PCH SerialIo I2C Pads Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination
  respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on.
**/
  UINT8                       PchSerialIoI2cPadsTermination[8];

/** Offset 0x021C - ISH GP GPIO Pin Muxing
  Determines ISH GP GPIO Pin muxing. See GPIO_*_MUXING_ISH_GP_x_GPIO_*. 'x' are GP_NUMBER
**/
  UINT32                      IshGpGpioPinMuxing[8];

/** Offset 0x023C - ISH UART Rx Pin Muxing
  Determines ISH UART Rx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_TXD_*
**/
  UINT32                      IshUartRxPinMuxing[3];

/** Offset 0x0248 - ISH UART Tx Pin Muxing
  Determines ISH UART Tx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_RXD_*
**/
  UINT32                      IshUartTxPinMuxing[3];

/** Offset 0x0254 - ISH UART Rts Pin Muxing
  Select ISH UART Rts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_RTS_* for possible values.
**/
  UINT32                      IshUartRtsPinMuxing[3];

/** Offset 0x0260 - ISH UART Rts Pin Muxing
  Select ISH UART Cts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_CTS_* for possible values.
**/
  UINT32                      IshUartCtsPinMuxing[3];

/** Offset 0x026C - ISH I2C SDA Pin Muxing
  Select ISH I2C SDA Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SDA_* for possible values.
**/
  UINT32                      IshI2cSdaPinMuxing[3];

/** Offset 0x0278 - ISH I2C SCL Pin Muxing
  Select ISH I2C SCL Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SCL_* for possible values.
**/
  UINT32                      IshI2cSclPinMuxing[3];

/** Offset 0x0284 - ISH SPI MOSI Pin Muxing
  Select ISH SPI MOSI Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MOSI_* for possible values.
**/
  UINT32                      IshSpiMosiPinMuxing[2];

/** Offset 0x028C - ISH SPI MISO Pin Muxing
  Select ISH SPI MISO Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MISO_* for possible values.
**/
  UINT32                      IshSpiMisoPinMuxing[2];

/** Offset 0x0294 - ISH SPI CLK Pin Muxing
  Select ISH SPI CLK Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CLK_* for possible values.
**/
  UINT32                      IshSpiClkPinMuxing[2];

/** Offset 0x029C - ISH SPI CS#N Pin Muxing
  Select ISH SPI CS#N Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CS<N>_* for possible
  values. N-SPI number, 0-1.
**/
  UINT32                      IshSpiCsPinMuxing[4];

/** Offset 0x02AC - ISH GP GPIO Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo GP#N GPIO pads termination
  respectively. #N are GP_NUMBER, not strictly relate to indexes of this table. Index
  0-23 -> ISH_GP_0-23, Index 24-25 -> ISH_GP_30-31
**/
  UINT8                       IshGpGpioPadTermination[8];

/** Offset 0x02B4 - ISH UART Rx Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rx pads termination
  respectively. #N-byte for each controller, byte0 for UART0 Rx, byte1 for UART1
  Rx, and so on.
**/
  UINT8                       IshUartRxPadTermination[3];

/** Offset 0x02B7 - ISH UART Tx Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Tx pads termination
  respectively. #N-byte for each controller, byte0 for UART0 Tx, byte1 for UART1
  Tx, and so on.
**/
  UINT8                       IshUartTxPadTermination[3];

/** Offset 0x02BA - ISH UART Rts Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rts pads termination
  respectively. #N-byte for each controller, byte0 for UART0 Rts, byte1 for UART1
  Rts, and so on.
**/
  UINT8                       IshUartRtsPadTermination[3];

/** Offset 0x02BD - ISH UART Rts Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Cts pads termination
  respectively. #N-byte for each controller, byte0 for UART0 Cts, byte1 for UART1
  Cts, and so on.
**/
  UINT8                       IshUartCtsPadTermination[3];

/** Offset 0x02C0 - ISH I2C SDA Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Sda pads termination
  respectively. #N-byte for each controller, byte0 for I2C0 Sda, byte1 for I2C1 Sda,
  and so on.
**/
  UINT8                       IshI2cSdaPadTermination[3];

/** Offset 0x02C3 - ISH I2C SCL Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Scl pads termination
  respectively. #N-byte for each controller, byte0 for I2C0 Scl, byte1 for I2C1 Scl,
  and so on.
**/
  UINT8                       IshI2cSclPadTermination[3];

/** Offset 0x02C6 - ISH SPI MOSI Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Mosi pads termination
  respectively. #N-byte for each controller, byte0 for SPI0 Mosi, byte1 for SPI1
  Mosi, and so on.
**/
  UINT8                       IshSpiMosiPadTermination[2];

/** Offset 0x02C8 - ISH SPI MISO Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Miso pads termination
  respectively. #N-byte for each controller, byte0 for SPI0 Miso, byte1 for SPI1
  Miso, and so on.
**/
  UINT8                       IshSpiMisoPadTermination[2];

/** Offset 0x02CA - ISH SPI CLK Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Clk pads termination
  respectively. #N-byte for each controller, byte0 for SPI0 Clk, byte1 for SPI1 Clk,
  and so on.
**/
  UINT8                       IshSpiClkPadTermination[2];

/** Offset 0x02CC - ISH SPI CS#N Pad termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Cs#M pads termination
  respectively. N*M-byte for each controller, byte0 for SPI0 Cs0, byte1 for SPI1
  Cs1, SPI1 Cs0, byte2, SPI1 Cs1, byte3
**/
  UINT8                       IshSpiCsPadTermination[4];

/** Offset 0x02D0 - Enable PCH ISH SPI Cs#N pins assigned
  Set if ISH SPI Cs#N pins are to be enabled by BIOS. 0: Disable; 1: Enable. N-Cs
  number: 0-1
**/
  UINT8                       PchIshSpiCsEnable[4];

/** Offset 0x02D4 - USB Per Port HS Preemphasis Bias
  USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
  UINT8                       Usb2PhyPetxiset[16];

/** Offset 0x02E4 - USB Per Port HS Transmitter Bias
  USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
  UINT8                       Usb2PhyTxiset[16];

/** Offset 0x02F4 - USB Per Port HS Transmitter Emphasis
  USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
  10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
  UINT8                       Usb2PhyPredeemp[16];

/** Offset 0x0304 - USB Per Port Half Bit Pre-emphasis
  USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
  One byte for each port.
**/
  UINT8                       Usb2PhyPehalfbit[16];

/** Offset 0x0314 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
  Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmphEnable[10];

/** Offset 0x031E - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
  USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
  <b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmph[10];

/** Offset 0x0328 - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
  Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmpEnable[10];

/** Offset 0x0332 - USB 3.0 TX Output Downscale Amplitude Adjustment
  USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default
  = 00h</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmp[10];

/** Offset 0x033C
**/
  UINT8                       PchUsb3HsioCtrlAdaptOffsetCfgEnable[10];

/** Offset 0x0346
**/
  UINT8                       PchUsb3HsioFilterSelNEnable[10];

/** Offset 0x0350
**/
  UINT8                       PchUsb3HsioFilterSelPEnable[10];

/** Offset 0x035A
**/
  UINT8                       PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10];

/** Offset 0x0364
**/
  UINT8                       PchUsb3HsioCtrlAdaptOffsetCfg[10];

/** Offset 0x036E
**/
  UINT8                       PchUsb3HsioOlfpsCfgPullUpDwnRes[10];

/** Offset 0x0378
**/
  UINT8                       PchUsb3HsioFilterSelN[10];

/** Offset 0x0382
**/
  UINT8                       PchUsb3HsioFilterSelP[10];

/** Offset 0x038C - Enable LAN
  Enable/disable LAN controller.
  $EN_DIS
**/
  UINT8                       PchLanEnable;

/** Offset 0x038D - Enable PCH TSN
  Enable/disable TSN on the PCH.
  $EN_DIS
**/
  UINT8                       PchTsnEnable;

/** Offset 0x038E - TSN Link Speed
  Set TSN Link Speed.
  0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps
**/
  UINT8                       PchTsnLinkSpeed;

/** Offset 0x038F - Reserved
**/
  UINT8                       Reserved6[9];

/** Offset 0x0398 - PCIe PTM enable/disable
  Enable/disable Precision Time Measurement for PCIE Root Ports.
**/
  UINT8                       PciePtm[28];

/** Offset 0x03B4 - PCIe DPC enable/disable
  Enable/disable Downstream Port Containment for PCIE Root Ports.
**/
  UINT8                       PcieDpc[28];

/** Offset 0x03D0 - PCIe DPC extensions enable/disable
  Enable/disable Downstream Port Containment Extensions for PCIE Root Ports.
**/
  UINT8                       PcieEdpc[28];

/** Offset 0x03EC - USB PDO Programming
  Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming
  during later phase. 1: enable, 0: disable
  $EN_DIS
**/
  UINT8                       UsbPdoProgramming;

/** Offset 0x03ED - Reserved
**/
  UINT8                       Reserved7[3];

/** Offset 0x03F0 - Power button debounce configuration
  Debounce time for PWRBTN in microseconds. For values not supported by HW, they will
  be rounded down to closest supported on. 0: disable, 250-1024000us: supported range
**/
  UINT32                      PmcPowerButtonDebounce;

/** Offset 0x03F4 - PCH eSPI Host and Device BME enabled
  PCH eSPI Host and Device BME enabled
  $EN_DIS
**/
  UINT8                       PchEspiBmeMasterSlaveEnabled;

/** Offset 0x03F5 - PCH eSPI Link Configuration Lock (SBLCL)
  Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI slaves
  addresseses from range 0x0 - 0x7FF
  $EN_DIS
**/
  UINT8                       PchEspiLockLinkConfiguration;

/** Offset 0x03F6 - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states
  Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT4:S5, BIT5:S0
**/
  UINT8                       PchFivrExtV1p05RailEnabledStates;

/** Offset 0x03F7 - Mask to enable the platform configuration of external V1p05 VR rail
  External V1P05 Rail Supported Configuration
**/
  UINT8                       PchFivrExtV1p05RailSupportedVoltageStates;

/** Offset 0x03F8 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtV1p05RailVoltage;

/** Offset 0x03FA - External V1P05 Icc Max Value
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtV1p05RailIccMax;

/** Offset 0x03FB - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states
  Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtVnnRailEnabledStates;

/** Offset 0x03FC - Mask to enable the platform configuration of external Vnn VR rail
  External Vnn Rail Supported Configuration
**/
  UINT8                       PchFivrExtVnnRailSupportedVoltageStates;

/** Offset 0x03FD - Reserved
**/
  UINT8                       Reserved8;

/** Offset 0x03FE - External Vnn Voltage Value that will be used in S0ix/Sx states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420
**/
  UINT16                      PchFivrExtVnnRailVoltage;

/** Offset 0x0400 - External Vnn Icc Max Value that will be used in S0ix/Sx states
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailIccMax;

/** Offset 0x0401 - Mask to enable the usage of external Vnn VR rail in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in
  Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT4:S5, BIT5:S0
**/
  UINT8                       PchFivrExtVnnRailSxEnabledStates;

/** Offset 0x0402 - External Vnn Voltage Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
  (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtVnnRailSxVoltage;

/** Offset 0x0404 - External Vnn Icc Max Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
  is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailSxIccMax;

/** Offset 0x0405 - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to low current mode voltage.
**/
  UINT8                       PchFivrVccinAuxLowToHighCurModeVolTranTime;

/** Offset 0x0406 - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToHighCurModeVolTranTime;

/** Offset 0x0407 - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToLowCurModeVolTranTime;

/** Offset 0x0408 - Transition time in microseconds from Off (0V) to High Current Mode Voltage
  This field has 1us resolution. When value is 0 Transition to 0V is disabled.
**/
  UINT16                      PchFivrVccinAuxOffToHighCurModeVolTranTime;

/** Offset 0x040A - PMC Debug Message Enable
  When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW
  will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix
  $EN_DIS
**/
  UINT8                       PmcDbgMsgEn;

/** Offset 0x040B - Reserved
**/
  UINT8                       Reserved9;

/** Offset 0x040C - Pointer of ChipsetInit Binary
  ChipsetInit Binary Pointer.
**/
  UINT32                      ChipsetInitBinPtr;

/** Offset 0x0410 - Length of ChipsetInit Binary
  ChipsetInit Binary Length.
**/
  UINT32                      ChipsetInitBinLen;

/** Offset 0x0414 - FIVR Dynamic Power Management
  Enable/Disable FIVR Dynamic Power Management.
  $EN_DIS
**/
  UINT8                       PchFivrDynPm;

/** Offset 0x0415 - Reserved
**/
  UINT8                       Reserved10;

/** Offset 0x0416 - External V1P05 Icc Max Value
  Granularity of this setting is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtV1p05RailIccMaximum;

/** Offset 0x0418 - External Vnn Icc Max Value that will be used in S0ix/Sx states
  Granularity of this setting is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtVnnRailIccMaximum;

/** Offset 0x041A - External Vnn Icc Max Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
  is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtVnnRailSxIccMaximum;

/** Offset 0x041C - Extented BIOS Direct Read Decode enable
  Enable/Disable access to bigger than 16MB BIOS Region through Direct Memory Reads.
  0: disabled (default), 1: enabled
  $EN_DIS
**/
  UINT8                       PchSpiExtendedBiosDecodeRangeEnable;

/** Offset 0x041D - Reserved
**/
  UINT8                       Reserved11[3];

/** Offset 0x0420 - Extended BIOS Direct Read Decode Range base
  Bits of 31:16 of a memory address that'll be a base for Extended BIOS Direct Read Decode.
**/
  UINT32                      PchSpiExtendedBiosDecodeRangeBase;

/** Offset 0x0424 - Extended BIOS Direct Read Decode Range limit
  Bits of 31:16 of a memory address that'll be a limit for Extended BIOS Direct Read Decode.
**/
  UINT32                      PchSpiExtendedBiosDecodeRangeLimit;

/** Offset 0x0428 - Reserved
**/
  UINT8                       Reserved12[12];

/** Offset 0x0434 - CNVi Configuration
  This option allows for automatic detection of Connectivity Solution. [Auto Detection]
  assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
  0:Disable, 1:Auto
**/
  UINT8                       CnviMode;

/** Offset 0x0435 - Reserved
**/
  UINT8                       Reserved13;

/** Offset 0x0436 - CNVi BT Core
  Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtCore;

/** Offset 0x0437 - CNVi BT Audio Offload
  Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtAudioOffload;

/** Offset 0x0438 - CNVi RF_RESET pin muxing
  Select CNVi RF_RESET# pin depending on board routing. ADP-P/M: GPP_A8 = 0x2942E408(default)
  or GPP_F4 = 0x194CE404. ADP-S: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h.
**/
  UINT32                      CnviRfResetPinMux;

/** Offset 0x043C - CNVi CLKREQ pin muxing
  Select CNVi CLKREQ pin depending on board routing. ADP-P/M: GPP_A9 = 0x3942E609(default)
  or GPP_F5 = 0x394CE605. ADP-S: 0. Refer to GPIO_*_MUXING_CNVI_CRF_XTAL_CLKREQ_*
  in GpioPins*.h.
**/
  UINT32                      CnviClkreqPinMux;

/** Offset 0x0440 - Enable Host C10 reporting through eSPI
  Enable/disable Host C10 reporting to Device via eSPI Virtual Wire.
  $EN_DIS
**/
  UINT8                       PchEspiHostC10ReportEnable;

/** Offset 0x0441 - PCH USB2 PHY Power Gating enable
  1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY
  Sus Well PG
  $EN_DIS
**/
  UINT8                       PmcUsb2PhySusPgEnable;

/** Offset 0x0442 - PCH USB OverCurrent mapping enable
  1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin
  mapping allow for NOA usage of OC pins
  $EN_DIS
**/
  UINT8                       PchUsbOverCurrentEnable;

/** Offset 0x0443 - Espi Lgmr Memory Range decode
  This option enables or disables espi lgmr
  $EN_DIS
**/
  UINT8                       PchEspiLgmrEnable;

/** Offset 0x0444 - External V1P05 Control Ramp Timer value
  Hold off time to be used when changing the v1p05_ctrl for external bypass value in us
**/
  UINT8                       PchFivrExtV1p05RailCtrlRampTmr;

/** Offset 0x0445 - External VNN Control Ramp Timer value
  Hold off time to be used when changing the vnn_ctrl for external bypass value in us
**/
  UINT8                       PchFivrExtVnnRailCtrlRampTmr;

/** Offset 0x0446 - Set SATA DEVSLP GPIO Reset Config
  Set SATA DEVSLP GPIO Reset Config per port. 0x00 - GpioResetDefault, 0x01 - GpioResumeReset,
  0x03 - GpioHostDeepReset, 0x05 - GpioPlatformReset, 0x07 - GpioDswReset. One byte
  for each port, byte0 for port0, byte1 for port1, and so on.
**/
  UINT8                       SataPortsDevSlpResetConfig[8];

/** Offset 0x044E - PCHHOT# pin
  Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PchHotEnable;

/** Offset 0x044F - SATA LED
  SATA LED indicating SATA controller activity. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       SataLedEnable;

/** Offset 0x0450 - VRAlert# Pin
  When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling
  to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PchPmVrAlert;

/** Offset 0x0451 - AMT Switch
  Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
  $EN_DIS
**/
  UINT8                       AmtEnabled;

/** Offset 0x0452 - WatchDog Timer Switch
  Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting
  is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       WatchDogEnabled;

/** Offset 0x0453 - PET Progress
  Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
  PET Events. Setting is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       FwProgress;

/** Offset 0x0454 - SOL Switch
  Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx.
  Setting is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       AmtSolEnabled;

/** Offset 0x0455 - Reserved
**/
  UINT8                       Reserved14;

/** Offset 0x0456 - OS Timer
  16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
  UINT16                      WatchDogTimerOs;

/** Offset 0x0458 - BIOS Timer
  16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
  UINT16                      WatchDogTimerBios;

/** Offset 0x045A - Force MEBX execution
  Enable/Disable. 0: Disable, 1: enable, Force MEBX execution.
  $EN_DIS
**/
  UINT8                       ForcMebxSyncUp;

/** Offset 0x045B - PCH PCIe root port connection type
  0: built-in device, 1:slot
**/
  UINT8                       PcieRpSlotImplemented[28];

/** Offset 0x0477 - PCIE RP Access Control Services Extended Capability
  Enable/Disable PCIE RP Access Control Services Extended Capability
**/
  UINT8                       PcieRpAcsEnabled[28];

/** Offset 0x0493 - PCIE RP Clock Power Management
  Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
  can still be controlled by L1 PM substates mechanism
**/
  UINT8                       PcieRpEnableCpm[28];

/** Offset 0x04AF - Reserved
**/
  UINT8                       Reserved15;

/** Offset 0x04B0 - PCIE RP Detect Timeout Ms
  The number of milliseconds within 0~65535 in reference code will wait for link to
  exit Detect state for enabled ports before assuming there is no device and potentially
  disabling the port.
**/
  UINT16                      PcieRpDetectTimeoutMs[28];

/** Offset 0x04E8 - ModPHY SUS Power Domain Dynamic Gating
  Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on
  PCH-H. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcModPhySusPgEnable;

/** Offset 0x04E9 - V1p05-PHY supply external FET control
  Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY
  supply. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcV1p05PhyExtFetControlEn;

/** Offset 0x04EA - V1p05-IS supply external FET control
  Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS
  supply. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcV1p05IsExtFetControlEn;

/** Offset 0x04EB - Enable/Disable PavpEnable
  Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
  $EN_DIS
**/
  UINT8                       PavpEnable;

/** Offset 0x04EC - CdClock Frequency selection
  0 (Default) Auto (Max based on reference clock frequency),  0: 192, 1: 307.2, 2:
  312 Mhz, 3: 324Mhz, 4: 326.4 Mhz, 5: 552 Mhz, 6: 556.8 Mhz, 7: 648 Mhz, 8: 652.8 Mhz
  0xFF: Auto (Max based on reference clock frequency), 0: 192, 1: 307.2, 2: 312 Mhz,
  3: 324Mhz, 4: 326.4 Mhz, 5: 552 Mhz, 6: 556.8 Mhz, 7: 648 Mhz, 8: 652.8 Mhz
**/
  UINT8                       CdClock;

/** Offset 0x04ED - Enable/Disable PeiGraphicsPeimInit
  <b>Enable(Default):</b> FSP will initialize the framebuffer and provide it via EFI_PEI_GRAPHICS_INFO_HOB.
  Disable: FSP will NOT initialize the framebuffer.
  $EN_DIS
**/
  UINT8                       PeiGraphicsPeimInit;

/** Offset 0x04EE - Enable D3 Hot in TCSS
  This policy will enable/disable D3 hot support in IOM
  $EN_DIS
**/
  UINT8                       D3HotEnable;

/** Offset 0x04EF - Enable or disable GNA device
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       GnaEnable;

/** Offset 0x04F0 - TypeC port GPIO setting
  GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined
  in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Adl
  = AlderLake)
**/
  UINT32                      IomTypeCPortPadCfg[8];

/** Offset 0x0510 - CPU USB3 Port Over Current Pin
  Describe the specific over current pin number of USBC Port N.
**/
  UINT8                       CpuUsb3OverCurrentPin[8];

/** Offset 0x0518 - Enable D3 Cold in TCSS
  This policy will enable/disable D3 cold support in IOM
  $EN_DIS
**/
  UINT8                       D3ColdEnable;

/** Offset 0x0519 - Enable/Disable PCIe tunneling for USB4
  Enable/Disable PCIe tunneling for USB4, default is enable
  $EN_DIS
**/
  UINT8                       ITbtPcieTunnelingForUsb4;

/** Offset 0x051A - Enable/Disable SkipFspGop
  Enable: Skip FSP provided GOP driver, Disable(Default): Use FSP provided GOP driver
  $EN_DIS
**/
  UINT8                       SkipFspGop;

/** Offset 0x051B - TC State in TCSS
  This TC C-State Limit in IOM
**/
  UINT8                       TcCstateLimit;

/** Offset 0x051C - Intel Graphics VBT (Video BIOS Table) Size
  Size of Internal Graphics VBT Image
**/
  UINT32                      VbtSize;

/** Offset 0x0520 - Platform LID Status for LFP Displays.
  LFP Display Lid Status (LID_STATUS enum): 0 (Default): LidClosed, 1: LidOpen.
  0: LidClosed, 1: LidOpen
**/
  UINT8                       LidStatus;

/** Offset 0x0521 - Reserved
**/
  UINT8                       Reserved16[8];

/** Offset 0x0529 - Enable VMD controller
  Enable/disable to VMD controller.0: Disable; 1: Enable(Default)
  $EN_DIS
**/
  UINT8                       VmdEnable;

/** Offset 0x052A - Map port under VMD
  Map/UnMap port under VMD
  $EN_DIS
**/
  UINT8                       VmdPort[31];

/** Offset 0x0549 - VMD Port Device
  VMD Root port device number.
**/
  UINT8                       VmdPortDev[31];

/** Offset 0x0568 - VMD Port Func
  VMD Root port function number.
**/
  UINT8                       VmdPortFunc[31];

/** Offset 0x0587 - VMD Config Bar size
  Set The VMD Config Bar Size.
**/
  UINT8                       VmdCfgBarSize;

/** Offset 0x0588 - VMD Config Bar Attributes
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdCfgBarAttr;

/** Offset 0x0589 - VMD Mem Bar1 size
  Set The VMD Mem Bar1 Size.
**/
  UINT8                       VmdMemBarSize1;

/** Offset 0x058A - VMD Mem Bar1 Attributes
  0: VMD_32BIT_NONPREFETCH(Default), 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdMemBar1Attr;

/** Offset 0x058B - VMD Mem Bar2 size
  Set The VMD Mem Bar2 Size.
**/
  UINT8                       VmdMemBarSize2;

/** Offset 0x058C - VMD Mem Bar2 Attributes
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdMemBar2Attr;

/** Offset 0x058D - Reserved
**/
  UINT8                       Reserved17[3];

/** Offset 0x0590 - VMD Variable
  VMD Variable Pointer.
**/
  UINT32                      VmdVariablePtr;

/** Offset 0x0594 - Temporary CfgBar address for VMD
  VMD Variable Pointer.
**/
  UINT32                      VmdCfgBarBase;

/** Offset 0x0598 - Temporary MemBar1 address for VMD
  VMD Variable Pointer.
**/
  UINT32                      VmdMemBar1Base;

/** Offset 0x059C - Temporary MemBar2 address for VMD
  VMD Variable Pointer.
**/
  UINT32                      VmdMemBar2Base;

/** Offset 0x05A0 - Reserved
**/
  UINT8                       Reserved18;

/** Offset 0x05A1 - Enable/Disable PMC-PD Solution
  This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution
  $EN_DIS
**/
  UINT8                       PmcPdEnable;

/** Offset 0x05A2 - TCSS Aux Orientation Override Enable
  Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
  UINT16                      TcssAuxOri;

/** Offset 0x05A4 - TCSS HSL Orientation Override Enable
  Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
  UINT16                      TcssHslOri;

/** Offset 0x05A6 - USB override in IOM
  This policy will enable/disable USB Connect override in IOM
  $EN_DIS
**/
  UINT8                       UsbOverride;

/** Offset 0x05A7 - ITBT Root Port Enable
  ITBT Root Port Enable, 0:Disable, 1:Enable
  0:Disable, 1:Enable
**/
  UINT8                       ITbtPcieRootPortEn[4];

/** Offset 0x05AB - TCSS USB Port Enable
  Bits 0, 1, ... max Type C port control enables
**/
  UINT8                       UsbTcPortEn;

/** Offset 0x05AC - ITBTForcePowerOn Timeout value
  ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000.
  100 = 100 ms.
**/
  UINT16                      ITbtForcePowerOnTimeoutInMs;

/** Offset 0x05AE - ITbtConnectTopology Timeout value
  ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range
  is 0-10000. 100 = 100 ms.
**/
  UINT16                      ITbtConnectTopologyTimeoutInMs;

/** Offset 0x05B0 - VCCST request for IOM
  This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5
  $EN_DIS
**/
  UINT8                       VccSt;

/** Offset 0x05B1 - Reserved
**/
  UINT8                       Reserved19;

/** Offset 0x05B2 - ITBT DMA LTR
  TCSS DMA1, DMA2 LTR value
**/
  UINT16                      ITbtDmaLtr[2];

/** Offset 0x05B6 - Reserved
**/
  UINT8                       Reserved20;

/** Offset 0x05B7 - Enable/Disable PTM
  This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports
  $EN_DIS
**/
  UINT8                       PtmEnabled[4];

/** Offset 0x05BB - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       SaPcieItbtRpLtrEnable[4];

/** Offset 0x05BF - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       SaPcieItbtRpSnoopLatencyOverrideMode[4];

/** Offset 0x05C3 - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       SaPcieItbtRpSnoopLatencyOverrideMultiplier[4];

/** Offset 0x05C7 - Reserved
**/
  UINT8                       Reserved21;

/** Offset 0x05C8 - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      SaPcieItbtRpSnoopLatencyOverrideValue[4];

/** Offset 0x05D0 - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       SaPcieItbtRpNonSnoopLatencyOverrideMode[4];

/** Offset 0x05D4 - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4];

/** Offset 0x05D8 - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      SaPcieItbtRpNonSnoopLatencyOverrideValue[4];

/** Offset 0x05E0 - Force LTR Override
  Force LTR Override.
**/
  UINT8                       SaPcieItbtRpForceLtrOverride[4];

/** Offset 0x05E4 - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       SaPcieItbtRpLtrConfigLock[4];

/** Offset 0x05E8 - Advanced Encryption Standard (AES) feature
  Enable or Disable Advanced Encryption Standard (AES) feature; </b>0: Disable; <b>1: Enable
  $EN_DIS
**/
  UINT8                       AesEnable;

/** Offset 0x05E9 - Power State 3 enable/disable
  PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; <b>1: Enable</b>.
  For all VR Indexes
**/
  UINT8                       Psi3Enable[5];

/** Offset 0x05EE - Power State 4 enable/disable
  PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; <b>1: Enable</b>.For
  all VR Indexes
**/
  UINT8                       Psi4Enable[5];

/** Offset 0x05F3 - Reserved
**/
  UINT8                       Reserved22;

/** Offset 0x05F4 - Imon slope correction
  PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
  Range is 0-200. 125 = 1.25. <b>0: Auto</b>.For all VR Indexes
**/
  UINT16                      ImonSlope[5];

/** Offset 0x05FE - Imon offset correction
  PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer.
  Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. <b>0: Auto</b>
**/
  UINT16                      ImonOffset[5];

/** Offset 0x0608 - Enable/Disable BIOS configuration of VR
  Enable/Disable BIOS configuration of VR; <b>0: Disable</b>; 1: Enable.For all VR Indexes
**/
  UINT8                       VrConfigEnable[5];

/** Offset 0x060D - Thermal Design Current enable/disable
  PCODE MMIO Mailbox: Thermal Design Current enable/disable; <b>0: Disable</b>; 1:
  Enable.For all VR Indexes
**/
  UINT8                       TdcEnable[5];

/** Offset 0x0612 - Reserved
**/
  UINT8                       Reserved23[2];

/** Offset 0x0614 - Thermal Design Current time window
  PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds.
  Range 1ms to 448s
**/
  UINT32                      TdcTimeWindow[5];

/** Offset 0x0628 - Thermal Design Current Lock
  PCODE MMIO Mailbox: Thermal Design Current Lock; <b>0: Disable</b>; 1: Enable.For
  all VR Indexes
**/
  UINT8                       TdcLock[5];

/** Offset 0x062D - Platform Psys slope correction
  PCODE MMIO Mailbox: Platform Psys slope correction. <b>0 - Auto</b> Specified in
  1/100 increment values. Range is 0-200. 125 = 1.25
**/
  UINT8                       PsysSlope;

/** Offset 0x062E - Platform Psys offset correction
  PCODE MMIO Mailbox: Platform Psys offset correction. <b>0 - Auto</b> Units 1/1000,
  Range 0-63999. For an offset of 25.348, enter 25348.
**/
  UINT16                      PsysOffset;

/** Offset 0x0630 - Acoustic Noise Mitigation feature
  Enable or Disable Acoustic Noise Mitigation feature. <b>0: Disabled</b>; 1: Enabled
  $EN_DIS
**/
  UINT8                       AcousticNoiseMitigation;

/** Offset 0x0631 - Disable Fast Slew Rate for Deep Package C States for VR domains
  Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
  feature enabled. <b>0: False</b>; 1: True
  $EN_DIS
**/
  UINT8                       FastPkgCRampDisable[5];

/** Offset 0x0636 - Slew Rate configuration for Deep Package C States for VR domains
  Slew Rate configuration for Deep Package C States for VR domains based on Acoustic
  Noise Mitigation feature enabled. ADL supports VCCIA FAST/2/4/8/16, VCCGT FAST/2/4/8
  and VCCSA FAST/2 <b>0: Fast/2</b>; 1: Fast/4; 2: Fast/8; 3: Fast/16
  0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
  UINT8                       SlowSlewRate[5];

/** Offset 0x063B - Reserved
**/
  UINT8                       Reserved24;

/** Offset 0x063C - Thermal Design Current current limit
  PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units.
  Range is 0-4095. 1000 = 125A. <b>0: Auto</b>. For all VR Indexes
**/
  UINT16                      TdcCurrentLimit[5];

/** Offset 0x0646 - AcLoadline
  PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
  0-6249. <b>Intel Recommended Defaults vary by domain and SKU.
**/
  UINT16                      AcLoadline[5];

/** Offset 0x0650 - DcLoadline
  PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
  0-6249.<b>Intel Recommended Defaults vary by domain and SKU.</b>
**/
  UINT16                      DcLoadline[5];

/** Offset 0x065A - Power State 1 Threshold current
  PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi1Threshold[5];

/** Offset 0x0664 - Power State 2 Threshold current
  PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi2Threshold[5];

/** Offset 0x066E - Power State 3 Threshold current
  PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi3Threshold[5];

/** Offset 0x0678 - Icc Max limit
  PCODE MMIO Mailbox: VR Icc Max limit. 0-512A in 1/4 A units. 400 = 100A
**/
  UINT16                      IccMax[5];

/** Offset 0x0682 - Enable or Disable TXT
  Enable or Disable TXT; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       TxtEnable;

/** Offset 0x0683 - Skip Multi-Processor Initialization
  When this is skipped, boot loader must initialize processors before SilicionInit
  API. </b>0: Initialize; <b>1: Skip
  $EN_DIS
**/
  UINT8                       SkipMpInit;

/** Offset 0x0684 - FIVR RFI Frequency
  PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. <b>0:
  Auto</b>. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock;
  0-1535 (Up to 153.5MHz) for 19MHz clock.
**/
  UINT16                      FivrRfiFrequency;

/** Offset 0x0686 - FIVR RFI Spread Spectrum
  Set the Spread Spectrum Range. <b>1.5%</b>; Range: 0.5%, 1%, 1.5%, 2%, 3%, 4%, 5%,
  6%. Each Range is translated to an encoded value for FIVR register. 0.5% = 0, 1%
  = 3, 1.5% = 8, 2% = 18, 3% = 28, 4% = 34, 5% = 39, 6% = 44.
**/
  UINT8                       FivrSpreadSpectrum;

/** Offset 0x0687 - Reserved
**/
  UINT8                       Reserved25;

/** Offset 0x0688 - CpuBistData
  Pointer CPU BIST Data
**/
  UINT32                      CpuBistData;

/** Offset 0x068C - CpuMpPpi
  <b>Optional</b> pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI.
  If not NULL, FSP will use the boot loader's implementation of multiprocessing.
  See section 5.1.4 of the FSP Integration Guide for more details.
**/
  UINT32                      CpuMpPpi;

/** Offset 0x0690 - Pre Wake Randomization time
  PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum pre-wake
  randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
  is enabled. Range 0-255 <b>0</b>.
**/
  UINT8                       PreWake;

/** Offset 0x0691 - Ramp Up Randomization time
  PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum Ramp Up
  randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
  is enabled.Range 0-255 <b>0</b>.
**/
  UINT8                       RampUp;

/** Offset 0x0692 - Ramp Down Randomization time
  PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum Ramp Down
  randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
  is enabled.Range 0-255 <b>0</b>.
**/
  UINT8                       RampDown;

/** Offset 0x0693 - Reserved
**/
  UINT8                       Reserved26;

/** Offset 0x0694 - VR Voltage Limit
  PCODE MMIO Mailbox: Voltage Limit. Range is 0 - 7999mV
**/
  UINT16                      VrVoltageLimit[5];

/** Offset 0x069E - VccIn Aux Imon IccMax
  PCODE MMIO Mailbox: VccIn Aux Imon IccMax. <b>0 - Auto</b> Values are in 1/4 Amp
  increments. Range is 0-512.
**/
  UINT16                      VccInAuxImonIccImax;

/** Offset 0x06A0 - Reserved
**/
  UINT8                       Reserved27[10];

/** Offset 0x06AA - FIVR RFI Spread Spectrum Enable or disable
  Enable or Disable FIVR RFI Spread Spectrum. 0: Disable ; <b> 1: Enable </b>
**/
  UINT8                       FivrSpectrumEnable;

/** Offset 0x06AB - Reserved
**/
  UINT8                       Reserved28[13];

/** Offset 0x06B8 - PpinSupport to view Protected Processor Inventory Number
  Enable or Disable or Auto (Based on End of Manufacturing flag. Disabled if this
  flag is set) for PPIN Support
  0: Disable, 1: Enable, 2: Auto
**/
  UINT8                       PpinSupport;

/** Offset 0x06B9 - Enable or Disable Minimum Voltage Override
  Enable or disable Minimum Voltage overrides ; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       EnableMinVoltageOverride;

/** Offset 0x06BA - Min Voltage for Runtime
  PCODE MMIO Mailbox: Minimum voltage for runtime. Valid if EnableMinVoltageOverride
  = 1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
  UINT16                      MinVoltageRuntime;

/** Offset 0x06BC - Reserved
**/
  UINT8                       Reserved29[2];

/** Offset 0x06BE - Min Voltage for C8
  PCODE MMIO Mailbox: Minimum voltage for C8. Valid if EnableMinVoltageOverride =
  1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
  UINT16                      MinVoltageC8;

/** Offset 0x06C0 - Smbios Type4 Max Speed Override
  Provide the option for platform to override the MaxSpeed field of Smbios Type 4.
  If this value is not zero, it dominates the field.
**/
  UINT16                      SmbiosType4MaxSpeedOverride;

/** Offset 0x06C2 - Reserved
**/
  UINT8                       Reserved30[5];

/** Offset 0x06C7 - AvxDisable
  Enable or Disable AVX Support. This only applicable when all small core is disabled.
  0: Enable, 1: Disable
**/
  UINT8                       AvxDisable;

/** Offset 0x06C8 - Avx3Disable
  DEPRECATED
  0: Enable, 1: Disable
**/
  UINT8                       Avx3Disable;

/** Offset 0x06C9 - Reserved
**/
  UINT8                       Reserved31;

/** Offset 0x06CA - CPU VR Power Delivery Design
  Used to communicate the power delivery design capability of the board. This value
  is an enum of the available power delivery segments that are defined in the Platform
  Design Guide.
**/
  UINT8                       VrPowerDeliveryDesign;

/** Offset 0x06CB - Reserved
**/
  UINT8                       Reserved32[32];

/** Offset 0x06EB - Enable Power Optimizer
  Enable DMI Power Optimizer on PCH side.
  $EN_DIS
**/
  UINT8                       PchPwrOptEnable;

/** Offset 0x06EC - PCH Flash Protection Ranges Write Enble
  Write or erase is blocked by hardware.
**/
  UINT8                       PchWriteProtectionEnable[5];

/** Offset 0x06F1 - PCH Flash Protection Ranges Read Enble
  Read is blocked by hardware.
**/
  UINT8                       PchReadProtectionEnable[5];

/** Offset 0x06F6 - PCH Protect Range Limit
  Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
  limit comparison.
**/
  UINT16                      PchProtectedRangeLimit[5];

/** Offset 0x0700 - PCH Protect Range Base
  Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
  UINT16                      PchProtectedRangeBase[5];

/** Offset 0x070A - Enable Pme
  Enable Azalia wake-on-ring.
  $EN_DIS
**/
  UINT8                       PchHdaPme;

/** Offset 0x070B - HD Audio Link Frequency
  HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz.
  0: 6MHz, 1: 12MHz, 2: 24MHz
**/
  UINT8                       PchHdaLinkFrequency;

/** Offset 0x070C - Enable PCH ISH SPI Cs0 pins assigned
  Set if ISH SPI Cs0 pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
  UINT8                       PchIshSpiCs0Enable[1];

/** Offset 0x070D - Enable PCH Io Apic Entry 24-119
  0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       PchIoApicEntry24_119;

/** Offset 0x070E - PCH Io Apic ID
  This member determines IOAPIC ID. Default is 0x02.
**/
  UINT8                       PchIoApicId;

/** Offset 0x070F - Enable PCH ISH SPI pins assigned
  Set if ISH SPI native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
  UINT8                       PchIshSpiEnable[1];

/** Offset 0x0710 - Enable PCH ISH UART pins assigned
  Set if ISH UART native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
  UINT8                       PchIshUartEnable[2];

/** Offset 0x0712 - Enable PCH ISH I2C pins assigned
  Set if ISH I2C native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
  UINT8                       PchIshI2cEnable[3];

/** Offset 0x0715 - Enable PCH ISH GP pins assigned
  Set if ISH GP native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
  UINT8                       PchIshGpEnable[8];

/** Offset 0x071D - PCH ISH PDT Unlock Msg
  0: False; 1: True.
  $EN_DIS
**/
  UINT8                       PchIshPdtUnlock;

/** Offset 0x071E - Enable PCH Lan LTR capabilty of PCH internal LAN
  0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       PchLanLtrEnable;

/** Offset 0x071F - Enable LOCKDOWN BIOS LOCK
  Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
  protection.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosLock;

/** Offset 0x0720 - PCH Compatibility Revision ID
  This member describes whether or not the CRID feature of PCH should be enabled.
  $EN_DIS
**/
  UINT8                       PchCrid;

/** Offset 0x0721 - RTC BIOS Interface Lock
  Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed.
  $EN_DIS
**/
  UINT8                       RtcBiosInterfaceLock;

/** Offset 0x0722 - RTC Cmos Memory Lock
  Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
  and and lower 128-byte bank of RTC RAM.
  $EN_DIS
**/
  UINT8                       RtcMemoryLock;

/** Offset 0x0723 - Enable PCIE RP HotPlug
  Indicate whether the root port is hot plug available.
**/
  UINT8                       PcieRpHotPlug[28];

/** Offset 0x073F - Enable PCIE RP Pm Sci
  Indicate whether the root port power manager SCI is enabled.
**/
  UINT8                       PcieRpPmSci[28];

/** Offset 0x075B - Enable PCIE RP Transmitter Half Swing
  Indicate whether the Transmitter Half Swing is enabled.
**/
  UINT8                       PcieRpTransmitterHalfSwing[28];

/** Offset 0x0777 - Enable PCIE RP Clk Req Detect
  Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
  UINT8                       PcieRpClkReqDetect[28];

/** Offset 0x0793 - PCIE RP Advanced Error Report
  Indicate whether the Advanced Error Reporting is enabled.
**/
  UINT8                       PcieRpAdvancedErrorReporting[28];

/** Offset 0x07AF - PCIE RP Unsupported Request Report
  Indicate whether the Unsupported Request Report is enabled.
**/
  UINT8                       PcieRpUnsupportedRequestReport[28];

/** Offset 0x07CB - PCIE RP Fatal Error Report
  Indicate whether the Fatal Error Report is enabled.
**/
  UINT8                       PcieRpFatalErrorReport[28];

/** Offset 0x07E7 - PCIE RP No Fatal Error Report
  Indicate whether the No Fatal Error Report is enabled.
**/
  UINT8                       PcieRpNoFatalErrorReport[28];

/** Offset 0x0803 - PCIE RP Correctable Error Report
  Indicate whether the Correctable Error Report is enabled.
**/
  UINT8                       PcieRpCorrectableErrorReport[28];

/** Offset 0x081F - PCIE RP System Error On Fatal Error
  Indicate whether the System Error on Fatal Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnFatalError[28];

/** Offset 0x083B - PCIE RP System Error On Non Fatal Error
  Indicate whether the System Error on Non Fatal Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnNonFatalError[28];

/** Offset 0x0857 - PCIE RP System Error On Correctable Error
  Indicate whether the System Error on Correctable Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnCorrectableError[28];

/** Offset 0x0873 - PCIE RP Max Payload
  Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
  UINT8                       PcieRpMaxPayload[28];

/** Offset 0x088F - Touch Host Controller Port 0 Assignment
  Assign THC Port 0
  0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0
**/
  UINT8                       ThcPort0Assignment;

/** Offset 0x0890 - Touch Host Controller Port 0 Interrupt Pin Mux
  Set THC Port 0 Pin Muxing Value if signal can be enabled on multiple pads. Refer
  to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
  UINT32                      ThcPort0InterruptPinMuxing;

/** Offset 0x0894 - Reserved
**/
  UINT8                       Reserved33;

/** Offset 0x0895 - Touch Host Controller Port 1 Assignment
  Assign THC Port 1
  0x0:ThcAssignmentNone, 0x1:ThcPort1AssignmentThc0, 0x2:ThcAssignmentThc1
**/
  UINT8                       ThcPort1Assignment;

/** Offset 0x0896 - Reserved
**/
  UINT8                       Reserved34[2];

/** Offset 0x0898 - Touch Host Controller Port 1 Interrupt Pin Mux
  Set THC Port 1 Pin Muxing Value if signal can be enabled on multiple pads. Refer
  to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
  UINT32                      ThcPort1InterruptPinMuxing;

/** Offset 0x089C - Reserved
**/
  UINT8                       Reserved35;

/** Offset 0x089D - PCIE RP Pcie Speed
  Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3;
  4: Gen4 (see: PCIE_SPEED).
**/
  UINT8                       PcieRpPcieSpeed[28];

/** Offset 0x08B9 - PCIE RP Physical Slot Number
  Indicates the slot number for the root port. Default is the value as root port index.
**/
  UINT8                       PcieRpPhysicalSlotNumber[28];

/** Offset 0x08D5 - PCIE RP Completion Timeout
  The root port completion timeout(see: PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
  UINT8                       PcieRpCompletionTimeout[28];

/** Offset 0x08F1 - PCIE RP Aspm
  The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
  PchPcieAspmAutoConfig.
**/
  UINT8                       PcieRpAspm[28];

/** Offset 0x090D - PCIE RP L1 Substates
  The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
  Default is PchPcieL1SubstatesL1_1_2.
**/
  UINT8                       PcieRpL1Substates[28];

/** Offset 0x0929 - Reserved
**/
  UINT8                       Reserved36[28];

/** Offset 0x0945 - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       PcieRpLtrEnable[28];

/** Offset 0x0961 - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       PcieRpLtrConfigLock[28];

/** Offset 0x097D - PCIe override default settings for EQ
  Choose PCIe EQ method
  $EN_DIS
**/
  UINT8                       PcieEqOverrideDefault;

/** Offset 0x097E - PCIe choose EQ method
  Choose PCIe EQ method
  0: HardwareEq, 1: FixedEq
**/
  UINT8                       PcieEqMethod;

/** Offset 0x097F - PCIe choose EQ mode
  Choose PCIe EQ mode
  0: PresetEq, 1: CoefficientEq
**/
  UINT8                       PcieEqMode;

/** Offset 0x0980 - PCIe EQ local transmitter override
  Enable/Disable local transmitter override
  $EN_DIS
**/
  UINT8                       PcieEqLocalTransmitterOverrideEnable;

/** Offset 0x0981 - PCIe number of valid list entries
  Select number of presets or coefficients depending on the mode
**/
  UINT8                       PcieEqPh3NumberOfPresetsOrCoefficients;

/** Offset 0x0982 - PCIe pre-cursor coefficient list
  Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PreCursorList[10];

/** Offset 0x098C - PCIe post-cursor coefficient list
  Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PostCursorList[10];

/** Offset 0x0996 - PCIe preset list
  Provide a list of presets to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PresetList[11];

/** Offset 0x09A1 - Reserved
**/
  UINT8                       Reserved37[3];

/** Offset 0x09A4 - PCIe EQ phase 1 downstream transmitter port preset
  Allows to select the downstream port preset value that will be used during phase
  1 of equalization
**/
  UINT32                      PcieEqPh1DownstreamPortTransmitterPreset;

/** Offset 0x09A8 - PCIe EQ phase 1 upstream tranmitter port preset
  Allows to select the upstream port preset value that will be used during phase 1
  of equalization
**/
  UINT32                      PcieEqPh1UpstreamPortTransmitterPreset;

/** Offset 0x09AC - PCIe EQ phase 2 local transmitter override preset
  Allows to select the value of the preset used during phase 2 local transmitter override
**/
  UINT8                       PcieEqPh2LocalTransmitterOverridePreset;

/** Offset 0x09AD - PCIE Enable Peer Memory Write
  This member describes whether Peer Memory Writes are enabled on the platform.
  $EN_DIS
**/
  UINT8                       PcieEnablePeerMemoryWrite[28];

/** Offset 0x09C9 - PCIE Compliance Test Mode
  Compliance Test Mode shall be enabled when using Compliance Load Board.
  $EN_DIS
**/
  UINT8                       PcieComplianceTestMode;

/** Offset 0x09CA - PCIE Rp Function Swap
  DEPRECATED. Allows BIOS to use root port function number swapping when root port
  of function 0 is disabled.
  $EN_DIS
**/
  UINT8                       PcieRpFunctionSwap;

/** Offset 0x09CB - Enable/Disable PEG GEN3 Static EQ Phase1 programming
  Program Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
  Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       CpuPcieGen3ProgramStaticEq;

/** Offset 0x09CC - Enable/Disable GEN4 Static EQ Phase1 programming
  Program Gen4 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
  Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       CpuPcieGen4ProgramStaticEq;

/** Offset 0x09CD - PCH Pm PME_B0_S5_DIS
  When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
  $EN_DIS
**/
  UINT8                       PchPmPmeB0S5Dis;

/** Offset 0x09CE - PCIE IMR
  Enables Isolated Memory Region for PCIe.
  $EN_DIS
**/
  UINT8                       PcieRpImrEnabled;

/** Offset 0x09CF - PCIE IMR port number
  Selects PCIE root port number for IMR feature.
**/
  UINT8                       PcieRpImrSelection;

/** Offset 0x09D0 - PCH Pm Wol Enable Override
  Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
  $EN_DIS
**/
  UINT8                       PchPmWolEnableOverride;

/** Offset 0x09D1 - PCH Pm Pcie Wake From DeepSx
  Determine if enable PCIe to wake from deep Sx.
  $EN_DIS
**/
  UINT8                       PchPmPcieWakeFromDeepSx;

/** Offset 0x09D2 - PCH Pm WoW lan Enable
  Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
  $EN_DIS
**/
  UINT8                       PchPmWoWlanEnable;

/** Offset 0x09D3 - PCH Pm WoW lan DeepSx Enable
  Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
  PWRM_CFG3 register.
  $EN_DIS
**/
  UINT8                       PchPmWoWlanDeepSxEnable;

/** Offset 0x09D4 - PCH Pm Lan Wake From DeepSx
  Determine if enable LAN to wake from deep Sx.
  $EN_DIS
**/
  UINT8                       PchPmLanWakeFromDeepSx;

/** Offset 0x09D5 - PCH Pm Deep Sx Pol
  Deep Sx Policy.
  $EN_DIS
**/
  UINT8                       PchPmDeepSxPol;

/** Offset 0x09D6 - PCH Pm Slp S3 Min Assert
  SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
  UINT8                       PchPmSlpS3MinAssert;

/** Offset 0x09D7 - PCH Pm Slp S4 Min Assert
  SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
  UINT8                       PchPmSlpS4MinAssert;

/** Offset 0x09D8 - PCH Pm Slp Sus Min Assert
  SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
  UINT8                       PchPmSlpSusMinAssert;

/** Offset 0x09D9 - PCH Pm Slp A Min Assert
  SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
  UINT8                       PchPmSlpAMinAssert;

/** Offset 0x09DA - USB Overcurrent Override for VISA
  This option overrides USB Over Current enablement state that USB OC will be disabled
  after enabling this option. Enable when VISA pin is muxed with USB OC
  $EN_DIS
**/
  UINT8                       PchEnableDbcObs;

/** Offset 0x09DB - PCH Pm Slp Strch Sus Up
  Enable SLP_X Stretching After SUS Well Power Up.
  $EN_DIS
**/
  UINT8                       PchPmSlpStrchSusUp;

/** Offset 0x09DC - PCH Pm Slp Lan Low Dc
  Enable/Disable SLP_LAN# Low on DC Power.
  $EN_DIS
**/
  UINT8                       PchPmSlpLanLowDc;

/** Offset 0x09DD - PCH Pm Pwr Btn Override Period
  PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
  UINT8                       PchPmPwrBtnOverridePeriod;

/** Offset 0x09DE - PCH Pm Disable Dsx Ac Present Pulldown
  When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
  $EN_DIS
**/
  UINT8                       PchPmDisableDsxAcPresentPulldown;

/** Offset 0x09DF - PCH Pm Disable Native Power Button
  Power button native mode disable.
  $EN_DIS
**/
  UINT8                       PchPmDisableNativePowerButton;

/** Offset 0x09E0 - PCH Pm ME_WAKE_STS
  Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
  $EN_DIS
**/
  UINT8                       PchPmMeWakeSts;

/** Offset 0x09E1 - PCH Pm WOL_OVR_WK_STS
  Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
  $EN_DIS
**/
  UINT8                       PchPmWolOvrWkSts;

/** Offset 0x09E2 - PCH Pm Reset Power Cycle Duration
  Could be customized in the unit of second. Please refer to EDS for all support settings.
  0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
  UINT8                       PchPmPwrCycDur;

/** Offset 0x09E3 - PCH Pm Pcie Pll Ssc
  Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No
  BIOS override.
**/
  UINT8                       PchPmPciePllSsc;

/** Offset 0x09E4 - PCH Legacy IO Low Latency Enable
  Set to enable low latency of legacy IO. <b>0: Disable</b>, 1: Enable
  $EN_DIS
**/
  UINT8                       PchLegacyIoLowLatency;

/** Offset 0x09E5 - PCH Sata Pwr Opt Enable
  SATA Power Optimizer on PCH side.
  $EN_DIS
**/
  UINT8                       SataPwrOptEnable;

/** Offset 0x09E6 - PCH Sata eSATA Speed Limit
  When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
  $EN_DIS
**/
  UINT8                       EsataSpeedLimit;

/** Offset 0x09E7 - PCH Sata Speed Limit
  Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
  UINT8                       SataSpeedLimit;

/** Offset 0x09E8 - Enable SATA Port HotPlug
  Enable SATA Port HotPlug.
**/
  UINT8                       SataPortsHotPlug[8];

/** Offset 0x09F0 - Enable SATA Port Interlock Sw
  Enable SATA Port Interlock Sw.
**/
  UINT8                       SataPortsInterlockSw[8];

/** Offset 0x09F8 - Enable SATA Port External
  Enable SATA Port External.
**/
  UINT8                       SataPortsExternal[8];

/** Offset 0x0A00 - Enable SATA Port SpinUp
  Enable the COMRESET initialization Sequence to the device.
**/
  UINT8                       SataPortsSpinUp[8];

/** Offset 0x0A08 - Enable SATA Port Solid State Drive
  0: HDD; 1: SSD.
**/
  UINT8                       SataPortsSolidStateDrive[8];

/** Offset 0x0A10 - Enable SATA Port Enable Dito Config
  Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
  UINT8                       SataPortsEnableDitoConfig[8];

/** Offset 0x0A18 - Enable SATA Port DmVal
  DITO multiplier. Default is 15.
**/
  UINT8                       SataPortsDmVal[8];

/** Offset 0x0A20 - Enable SATA Port DmVal
  DEVSLP Idle Timeout (DITO), Default is 625.
**/
  UINT16                      SataPortsDitoVal[8];

/** Offset 0x0A30 - Enable SATA Port ZpOdd
  Support zero power ODD.
**/
  UINT8                       SataPortsZpOdd[8];

/** Offset 0x0A38 - PCH Sata Rst Raid Alternate Id
  Enable RAID Alternate ID.
  $EN_DIS
**/
  UINT8                       SataRstRaidDeviceId;

/** Offset 0x0A39 - PCH Sata Rst Pcie Storage Remap enable
  Enable Intel RST for PCIe Storage remapping.
**/
  UINT8                       SataRstPcieEnable[3];

/** Offset 0x0A3C - PCH Sata Rst Pcie Storage Port
  Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
  UINT8                       SataRstPcieStoragePort[3];

/** Offset 0x0A3F - PCH Sata Rst Pcie Device Reset Delay
  PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
  UINT8                       SataRstPcieDeviceResetDelay[3];

/** Offset 0x0A42 - UFS enable/disable
  PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
  $EN_DIS
**/
  UINT8                       UfsEnable[2];

/** Offset 0x0A44 - IEH Mode
  Integrated Error Handler Mode, 0: Bypass, 1: Enable
  0: Bypass, 1:Enable
**/
  UINT8                       IehMode;

/** Offset 0x0A45 - Reserved
**/
  UINT8                       Reserved38;

/** Offset 0x0A46 - Thermal Throttling Custimized T0Level Value
  Custimized T0Level value.
**/
  UINT16                      PchT0Level;

/** Offset 0x0A48 - Thermal Throttling Custimized T1Level Value
  Custimized T1Level value.
**/
  UINT16                      PchT1Level;

/** Offset 0x0A4A - Thermal Throttling Custimized T2Level Value
  Custimized T2Level value.
**/
  UINT16                      PchT2Level;

/** Offset 0x0A4C - Enable The Thermal Throttle
  Enable the thermal throttle function.
  $EN_DIS
**/
  UINT8                       PchTTEnable;

/** Offset 0x0A4D - PMSync State 13
  When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
  at least T2 state.
  $EN_DIS
**/
  UINT8                       PchTTState13Enable;

/** Offset 0x0A4E - Thermal Throttle Lock
  Thermal Throttle Lock.
  $EN_DIS
**/
  UINT8                       PchTTLock;

/** Offset 0x0A4F - Thermal Throttling Suggested Setting
  Thermal Throttling Suggested Setting.
  $EN_DIS
**/
  UINT8                       TTSuggestedSetting;

/** Offset 0x0A50 - Enable PCH Cross Throttling
  Enable/Disable PCH Cross Throttling
  $EN_DIS
**/
  UINT8                       TTCrossThrottling;

/** Offset 0x0A51 - DMI Thermal Sensor Autonomous Width Enable
  DMI Thermal Sensor Autonomous Width Enable.
  $EN_DIS
**/
  UINT8                       PchDmiTsawEn;

/** Offset 0x0A52 - DMI Thermal Sensor Suggested Setting
  DMT thermal sensor suggested representative values.
  $EN_DIS
**/
  UINT8                       DmiSuggestedSetting;

/** Offset 0x0A53 - Thermal Sensor 0 Target Width
  Thermal Sensor 0 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS0TW;

/** Offset 0x0A54 - Thermal Sensor 1 Target Width
  Thermal Sensor 1 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS1TW;

/** Offset 0x0A55 - Thermal Sensor 2 Target Width
  Thermal Sensor 2 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS2TW;

/** Offset 0x0A56 - Thermal Sensor 3 Target Width
  Thermal Sensor 3 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS3TW;

/** Offset 0x0A57 - Port 0 T1 Multipler
  Port 0 T1 Multipler.
**/
  UINT8                       SataP0T1M;

/** Offset 0x0A58 - Port 0 T2 Multipler
  Port 0 T2 Multipler.
**/
  UINT8                       SataP0T2M;

/** Offset 0x0A59 - Port 0 T3 Multipler
  Port 0 T3 Multipler.
**/
  UINT8                       SataP0T3M;

/** Offset 0x0A5A - Port 0 Tdispatch
  Port 0 Tdispatch.
**/
  UINT8                       SataP0TDisp;

/** Offset 0x0A5B - Port 1 T1 Multipler
  Port 1 T1 Multipler.
**/
  UINT8                       SataP1T1M;

/** Offset 0x0A5C - Port 1 T2 Multipler
  Port 1 T2 Multipler.
**/
  UINT8                       SataP1T2M;

/** Offset 0x0A5D - Port 1 T3 Multipler
  Port 1 T3 Multipler.
**/
  UINT8                       SataP1T3M;

/** Offset 0x0A5E - Port 1 Tdispatch
  Port 1 Tdispatch.
**/
  UINT8                       SataP1TDisp;

/** Offset 0x0A5F - Port 0 Tinactive
  Port 0 Tinactive.
**/
  UINT8                       SataP0Tinact;

/** Offset 0x0A60 - Port 0 Alternate Fast Init Tdispatch
  Port 0 Alternate Fast Init Tdispatch.
  $EN_DIS
**/
  UINT8                       SataP0TDispFinit;

/** Offset 0x0A61 - Port 1 Tinactive
  Port 1 Tinactive.
**/
  UINT8                       SataP1Tinact;

/** Offset 0x0A62 - Port 1 Alternate Fast Init Tdispatch
  Port 1 Alternate Fast Init Tdispatch.
  $EN_DIS
**/
  UINT8                       SataP1TDispFinit;

/** Offset 0x0A63 - Sata Thermal Throttling Suggested Setting
  Sata Thermal Throttling Suggested Setting.
  $EN_DIS
**/
  UINT8                       SataThermalSuggestedSetting;

/** Offset 0x0A64 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
  $EN_DIS
**/
  UINT8                       PchMemoryThrottlingEnable;

/** Offset 0x0A65 - Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryPmsyncEnable[2];

/** Offset 0x0A67 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryC0TransmitEnable[2];

/** Offset 0x0A69 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryPinSelection[2];

/** Offset 0x0A6B - Reserved
**/
  UINT8                       Reserved39;

/** Offset 0x0A6C - Thermal Device Temperature
  Decides the temperature.
**/
  UINT16                      PchTemperatureHotLevel;

/** Offset 0x0A6E - USB2 Port Over Current Pin
  Describe the specific over current pin number of USB 2.0 Port N.
**/
  UINT8                       Usb2OverCurrentPin[16];

/** Offset 0x0A7E - USB3 Port Over Current Pin
  Describe the specific over current pin number of USB 3.0 Port N.
**/
  UINT8                       Usb3OverCurrentPin[10];

/** Offset 0x0A88 - Enable xHCI LTR override
  Enables override of recommended LTR values for xHCI
  $EN_DIS
**/
  UINT8                       PchUsbLtrOverrideEnable;

/** Offset 0x0A89 - Reserved
**/
  UINT8                       Reserved40[3];

/** Offset 0x0A8C - xHCI High Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting
**/
  UINT32                      PchUsbLtrHighIdleTimeOverride;

/** Offset 0x0A90 - xHCI Medium Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting
**/
  UINT32                      PchUsbLtrMediumIdleTimeOverride;

/** Offset 0x0A94 - xHCI Low Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting
**/
  UINT32                      PchUsbLtrLowIdleTimeOverride;

/** Offset 0x0A98 - Enable 8254 Static Clock Gating
  Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
  might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
  legacy OS using 8254 timer. Also enable this while S0ix is enabled.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGating;

/** Offset 0x0A99 - Enable 8254 Static Clock Gating On S3
  This is only applicable when Enable8254ClockGating is disabled. FSP will do the
  8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
  avoids the SMI requirement for the programming.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGatingOnS3;

/** Offset 0x0A9A - Enable TCO timer.
  When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
  huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
  emulation must be enabled, and WDAT table must not be exposed to the OS.
  $EN_DIS
**/
  UINT8                       EnableTcoTimer;

/** Offset 0x0A9B - Hybrid Storage Detection and Configuration Mode
  Enables support for Hybrid storage devices. 0: Disabled; 1: Dynamic Configuration.
  Default is 0: Disabled
  0: Disabled, 1: Dynamic Configuration
**/
  UINT8                       HybridStorageMode;

/** Offset 0x0A9C - Reserved
**/
  UINT8                       Reserved41[4];

/** Offset 0x0AA0 - BgpdtHash[4]
  BgpdtHash values
**/
  UINT64                      BgpdtHash[4];

/** Offset 0x0AC0 - BiosGuardAttr
  BiosGuardAttr default values
**/
  UINT32                      BiosGuardAttr;

/** Offset 0x0AC4 - Reserved
**/
  UINT8                       Reserved42[4];

/** Offset 0x0AC8 - BiosGuardModulePtr
  BiosGuardModulePtr default values
**/
  UINT64                      BiosGuardModulePtr;

/** Offset 0x0AD0 - SendEcCmd
  SendEcCmd function pointer. \n
  @code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
  EcCmdType, IN UINT8  EcCmd, IN UINT8  SendData, IN OUT UINT8  *ReceiveData); @endcode
**/
  UINT64                      SendEcCmd;

/** Offset 0x0AD8 - EcCmdProvisionEav
  Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
  UINT8                       EcCmdProvisionEav;

/** Offset 0x0AD9 - EcCmdLock
  EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
  UINT8                       EcCmdLock;

/** Offset 0x0ADA - Skip Ssid Programming.
  When set to TRUE, silicon code will not do any SSID programming and platform code
  needs to handle that by itself properly.
  $EN_DIS
**/
  UINT8                       SiSkipSsidProgramming;

/** Offset 0x0ADB - Reserved
**/
  UINT8                       Reserved43;

/** Offset 0x0ADC - Change Default SVID
  Change the default SVID used in FSP to programming internal devices. This is only
  valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiCustomizedSvid;

/** Offset 0x0ADE - Change Default SSID
  Change the default SSID used in FSP to programming internal devices. This is only
  valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiCustomizedSsid;

/** Offset 0x0AE0 - SVID SDID table Poniter.
  The address of the table of SVID SDID to customize each SVID SDID entry. This is
  only valid when SkipSsidProgramming is FALSE.
**/
  UINT32                      SiSsidTablePtr;

/** Offset 0x0AE4 - Number of ssid table.
  SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr.
  This is only valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiNumberOfSsidTableEntry;

/** Offset 0x0AE6 - USB2 Port Reset Message Enable
  0: Disable USB2 Port Reset Message; 1: Enable USB2 Port Reset Message; This must
  be enable for USB2 Port those are paired with CPU XHCI Port
**/
  UINT8                       PortResetMessageEnable[16];

/** Offset 0x0AF6 - SATA RST Interrupt Mode
  Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
  0:Msix, 1:Msi, 2:Legacy
**/
  UINT8                       SataRstInterrupt;

/** Offset 0x0AF7 - ME Unconfig on RTC clear
  0: Disable ME Unconfig On Rtc Clear. <b>1: Enable ME Unconfig On Rtc Clear</b>.
  2: Cmos is clear, status unkonwn. 3: Reserved
  0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
  is clear, 3: Reserved
**/
  UINT8                       MeUnconfigOnRtcClear;

/** Offset 0x0AF8 - Enforce Enhanced Debug Mode
  Determine if ME should enter Enhanced Debug Mode. <b>0: disable</b>, 1: enable
  $EN_DIS
**/
  UINT8                       EnforceEDebugMode;

/** Offset 0x0AF9 - Enable PS_ON.
  PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
  target that will be required by the California Energy Commission (CEC). When FALSE,
  PS_ON is to be disabled.
  $EN_DIS
**/
  UINT8                       PsOnEnable;

/** Offset 0x0AFA - Pmc Cpu C10 Gate Pin Enable
  Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO
  and VccSTG rails instead of SLP_S0# pin.
  $EN_DIS
**/
  UINT8                       PmcCpuC10GatePinEnable;

/** Offset 0x0AFB - Pch Dmi Aspm Ctrl
  ASPM configuration on the PCH side of the DMI/OPI Link. Default is <b>PchPcieAspmL1</b>
  0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
  UINT8                       PchDmiAspmCtrl;

/** Offset 0x0AFC - PchDmiCwbEnable
  Central Write Buffer feature configurable and enabled by default
  $EN_DIS
**/
  UINT8                       PchDmiCwbEnable;

/** Offset 0x0AFD - OS IDLE Mode Enable
  Enable/Disable OS Idle Mode
  $EN_DIS
**/
  UINT8                       PmcOsIdleEnable;

/** Offset 0x0AFE - S0ix Auto-Demotion
  Enable/Disable the Low Power Mode Auto-Demotion Host Control feature.
  $EN_DIS
**/
  UINT8                       PchS0ixAutoDemotion;

/** Offset 0x0AFF - Latch Events C10 Exit
  When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are
  captured on C10 exit (instead of C10 entry which is default)
  $EN_DIS
**/
  UINT8                       PchPmLatchEventsC10Exit;

/** Offset 0x0B00 - Reserved
**/
  UINT8                       Reserved44[12];

/** Offset 0x0B0C - PCIE Eq Ph3 Lane Param Cm
  CPU_PCIE_EQ_LANE_PARAM. Coefficient C-1.
**/
  UINT8                       CpuPcieEqPh3LaneParamCm[32];

/** Offset 0x0B2C - PCIE Eq Ph3 Lane Param Cp
  CPU_PCIE_EQ_LANE_PARAM. Coefficient C+1.
**/
  UINT8                       CpuPcieEqPh3LaneParamCp[32];

/** Offset 0x0B4C - Gen3 Root port preset values per lane
  Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 8 is default
  for each lane
**/
  UINT8                       CpuPcieGen3RootPortPreset[20];

/** Offset 0x0B60 - Pcie Gen4 Root port preset values per lane
  Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 8 is default
  for each lane
**/
  UINT8                       CpuPcieGen4RootPortPreset[20];

/** Offset 0x0B74 - Pcie Gen3 End port preset values per lane
  Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 7 is default
  for each lane
**/
  UINT8                       CpuPcieGen3EndPointPreset[20];

/** Offset 0x0B88 - Pcie Gen4 End port preset values per lane
  Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 7 is default
  for each lane
**/
  UINT8                       CpuPcieGen4EndPointPreset[20];

/** Offset 0x0B9C - Pcie Gen3 End port Hint values per lane
  Used for programming Pcie Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       CpuPcieGen3EndPointHint[20];

/** Offset 0x0BB0 - Pcie Gen4 End port Hint values per lane
  Used for programming Pcie Gen4 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       CpuPcieGen4EndPointHint[20];

/** Offset 0x0BC4 - CPU PCIe Fia Programming
  Load Fia configuration if enable. 0: Disable; 1: Enable(Default).
  $EN_DIS
**/
  UINT8                       CpuPcieFiaProgramming;

/** Offset 0x0BC5 - CPU PCIe RootPort Clock Gating
  Describes whether the PCI Express Clock Gating for each root port is enabled by
  platform modules. 0: Disable; 1: Enable(Default).
  $EN_DIS
**/
  UINT8                       CpuPcieClockGating[4];

/** Offset 0x0BC9 - CPU PCIe RootPort Power Gating
  Describes whether the PCI Express Power Gating for each root port is enabled by
  platform modules. 0: Disable; 1: Enable(Default).
  $EN_DIS
**/
  UINT8                       CpuPciePowerGating[4];

/** Offset 0x0BCD - PCIE Compliance Test Mode
  Compliance Test Mode shall be enabled when using Compliance Load Board.
  $EN_DIS
**/
  UINT8                       CpuPcieComplianceTestMode;

/** Offset 0x0BCE - PCIE Enable Peer Memory Write
  This member describes whether Peer Memory Writes are enabled on the platform.
  $EN_DIS
**/
  UINT8                       CpuPcieEnablePeerMemoryWrite;

/** Offset 0x0BCF - PCIE Rp Function Swap
  Allows BIOS to use root port function number swapping when root port of function
  0 is disabled.
  $EN_DIS
**/
  UINT8                       CpuPcieRpFunctionSwap;

/** Offset 0x0BD0 - PCI Express Slot Selection
  Select the PCIe M2 or CEMx4 slot.0: CEMx4 slot; 1: M2 slot(Default).
  $EN_DIS
**/
  UINT8                       CpuPcieSlotSelection;

/** Offset 0x0BD1 - Reserved
**/
  UINT8                       Reserved45[3];

/** Offset 0x0BD4 - CPU PCIE device override table pointer
  The PCIe device table is being used to override PCIe device ASPM settings. This
  is a pointer points to a 32bit address. And it's only used in PostMem phase. Please
  refer to CPU_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId
  must be 0.
**/
  UINT32                      CpuPcieDeviceOverrideTablePtr;

/** Offset 0x0BD8 - Enable PCIE RP HotPlug
  Indicate whether the root port is hot plug available.
**/
  UINT8                       CpuPcieRpHotPlug[4];

/** Offset 0x0BDC - Enable PCIE RP Pm Sci
  Indicate whether the root port power manager SCI is enabled.
**/
  UINT8                       CpuPcieRpPmSci[4];

/** Offset 0x0BE0 - Enable PCIE RP Transmitter Half Swing
  Indicate whether the Transmitter Half Swing is enabled.
**/
  UINT8                       CpuPcieRpTransmitterHalfSwing[4];

/** Offset 0x0BE4 - PCIE RP Access Control Services Extended Capability
  Enable/Disable PCIE RP Access Control Services Extended Capability
**/
  UINT8                       CpuPcieRpAcsEnabled[4];

/** Offset 0x0BE8 - PCIE RP Clock Power Management
  Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
  can still be controlled by L1 PM substates mechanism
**/
  UINT8                       CpuPcieRpEnableCpm[4];

/** Offset 0x0BEC - PCIE RP Advanced Error Report
  Indicate whether the Advanced Error Reporting is enabled.
**/
  UINT8                       CpuPcieRpAdvancedErrorReporting[4];

/** Offset 0x0BF0 - PCIE RP Unsupported Request Report
  Indicate whether the Unsupported Request Report is enabled.
**/
  UINT8                       CpuPcieRpUnsupportedRequestReport[4];

/** Offset 0x0BF4 - PCIE RP Fatal Error Report
  Indicate whether the Fatal Error Report is enabled.
**/
  UINT8                       CpuPcieRpFatalErrorReport[4];

/** Offset 0x0BF8 - PCIE RP No Fatal Error Report
  Indicate whether the No Fatal Error Report is enabled.
**/
  UINT8                       CpuPcieRpNoFatalErrorReport[4];

/** Offset 0x0BFC - PCIE RP Correctable Error Report
  Indicate whether the Correctable Error Report is enabled.
**/
  UINT8                       CpuPcieRpCorrectableErrorReport[4];

/** Offset 0x0C00 - PCIE RP System Error On Fatal Error
  Indicate whether the System Error on Fatal Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnFatalError[4];

/** Offset 0x0C04 - PCIE RP System Error On Non Fatal Error
  Indicate whether the System Error on Non Fatal Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnNonFatalError[4];

/** Offset 0x0C08 - PCIE RP System Error On Correctable Error
  Indicate whether the System Error on Correctable Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnCorrectableError[4];

/** Offset 0x0C0C - PCIE RP Max Payload
  Max Payload Size supported, Default 128B, see enum CPU_PCIE_MAX_PAYLOAD.
**/
  UINT8                       CpuPcieRpMaxPayload[4];

/** Offset 0x0C10 - DPC for PCIE RP Mask
  Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable.
  One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpDpcEnabled[4];

/** Offset 0x0C14 - DPC Extensions PCIE RP Mask
  Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit
  for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpDpcExtensionsEnabled[4];

/** Offset 0x0C18 - CPU PCIe root port connection type
  0: built-in device, 1:slot
**/
  UINT8                       CpuPcieRpSlotImplemented[4];

/** Offset 0x0C1C - PCIE RP Gen3 Equalization Phase Method
  PCIe Gen3 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
  1: hardware equalization; 4: Fixed Coeficients.
**/
  UINT8                       CpuPcieRpGen3EqPh3Method[4];

/** Offset 0x0C20 - PCIE RP Gen4 Equalization Phase Method
  PCIe Gen4 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
  1: hardware equalization; 4: Fixed Coeficients.
**/
  UINT8                       CpuPcieRpGen4EqPh3Method[4];

/** Offset 0x0C24 - PCIE RP Physical Slot Number
  Indicates the slot number for the root port. Default is the value as root port index.
**/
  UINT8                       CpuPcieRpPhysicalSlotNumber[4];

/** Offset 0x0C28 - PCIE RP Aspm
  The ASPM configuration of the root port (see: CPU_PCIE_ASPM_CONTROL).0: Disable;
  1: CpuPcieAspmL0s; 2: CpuPcieAspmL1; 3:CpuPcieAspmL0sL1(Default)
**/
  UINT8                       CpuPcieRpAspm[4];

/** Offset 0x0C2C - PCIE RP L1 Substates
  The L1 Substates configuration of the root port (see: CPU_PCIE_L1SUBSTATES_CONTROL).
  Default is CpuPcieL1SubstatesL1_1_2.
**/
  UINT8                       CpuPcieRpL1Substates[4];

/** Offset 0x0C30 - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       CpuPcieRpLtrEnable[4];

/** Offset 0x0C34 - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       CpuPcieRpLtrConfigLock[4];

/** Offset 0x0C38 - RpPtmBytes
**/
  UINT8                       RpPtmBytes[4];

/** Offset 0x0C3C - PCIE RP Detect Timeout Ms
  The number of milliseconds within 0~65535 in reference code will wait for link to
  exit Detect state for enabled ports before assuming there is no device and potentially
  disabling the port.
**/
  UINT16                      CpuPcieRpDetectTimeoutMs[4];

/** Offset 0x0C44 - Multi-VC for PCIE RP Mask
  Enable/disable Multiple Virtual Channel for PCIE Root Ports. 0: disable, 1: enable.
  One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpMultiVcEnabled[4];

/** Offset 0x0C48 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate3UniqTranEnable[10];

/** Offset 0x0C52 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3
  USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], <b>Default
  = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate3UniqTran[10];

/** Offset 0x0C5C - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate2UniqTranEnable[10];

/** Offset 0x0C66 - USB 3.0 TX Output Unique Transition Bit Scale for rate 2
  USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate2UniqTran[10];

/** Offset 0x0C70 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate1UniqTranEnable[10];

/** Offset 0x0C7A - USB 3.0 TX Output Unique Transition Bit Scale for rate 1
  USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate1UniqTran[10];

/** Offset 0x0C84 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate0UniqTranEnable[10];

/** Offset 0x0C8E - USB 3.0 TX Output Unique Transition Bit Scale for rate 0
  USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate0UniqTran[10];

/** Offset 0x0C98 - Skip PAM regsiter lock
  Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
  PAM registers will be locked by RC
  $EN_DIS
**/
  UINT8                       SkipPamLock;

/** Offset 0x0C99 - EDRAM Test Mode
  Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
  PAM registers will be locked by RC
  0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode
**/
  UINT8                       EdramTestMode;

/** Offset 0x0C9A - Enable/Disable IGFX RenderStandby
  Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
  $EN_DIS
**/
  UINT8                       RenderStandby;

/** Offset 0x0C9B - Enable/Disable IGFX PmSupport
  Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
  $EN_DIS
**/
  UINT8                       PmSupport;

/** Offset 0x0C9C - Enable/Disable CdynmaxClamp
  Enable: Enable CdynmaxClamp, Disable(Default): Disable CdynmaxClamp
  $EN_DIS
**/
  UINT8                       CdynmaxClampEnable;

/** Offset 0x0C9D - GT Frequency Limit
  0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
  7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
  650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
  0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
  0x18: 1200 Mhz
  0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
  7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
  650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
  0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
  0x18: 1200 Mhz
**/
  UINT8                       GtFreqMax;

/** Offset 0x0C9E - Disable Turbo GT
   0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
  $EN_DIS
**/
  UINT8                       DisableTurboGt;

/** Offset 0x0C9F - Enable/Disable CdClock Init
  Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full
  CD clock if not initialized by Gfx PEIM
  $EN_DIS
**/
  UINT8                       SkipCdClockInit;

/** Offset 0x0CA0 - Enable RC1p frequency request to PMA (provided all other conditions are met)
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       RC1pFreqEnable;

/** Offset 0x0CA1 - Enable TSN Multi-VC
  Enable/disable Multi Virtual Channels(VC) in TSN.
  $EN_DIS
**/
  UINT8                       PchTsnMultiVcEnable;

/** Offset 0x0CA2 - Reserved
**/
  UINT8                       Reserved46[2];

/** Offset 0x0CA4 - LogoPixelHeight Address
  Address of LogoPixelHeight
**/
  UINT32                      LogoPixelHeight;

/** Offset 0x0CA8 - LogoPixelWidth Address
  Address of LogoPixelWidth
**/
  UINT32                      LogoPixelWidth;

/** Offset 0x0CAC - Reserved
**/
  UINT8                       Reserved47[5];

/** Offset 0x0CB1 - RSR feature
  Enable or Disable RSR feature; 0: Disable; <b>1: Enable </b>
  $EN_DIS
**/
  UINT8                       EnableRsr;

/** Offset 0x0CB2 - Reserved
**/
  UINT8                       Reserved48[4];

/** Offset 0x0CB6 - Enable or Disable HWP
  Enable or Disable HWP(Hardware P states) Support. 0: Disable; <b>1: Enable;</b>
  2-3:Reserved
  $EN_DIS
**/
  UINT8                       Hwp;

/** Offset 0x0CB7 - Hardware Duty Cycle Control
  Hardware Duty Cycle Control configuration. 0: Disabled; <b>1: Enabled</b> 2-3:Reserved
  $EN_DIS
**/
  UINT8                       HdcControl;

/** Offset 0x0CB8 - Package Long duration turbo mode time
  Package Long duration turbo mode time window in seconds. Valid values(Unit in seconds)
  0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
  UINT8                       PowerLimit1Time;

/** Offset 0x0CB9 - Short Duration Turbo Mode
  Enable or Disable short duration Turbo Mode. </b>0 : Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PowerLimit2;

/** Offset 0x0CBA - Turbo settings Lock
  Lock all Turbo settings Enable/Disable; <b>0: Disable , </b> 1: Enable
  $EN_DIS
**/
  UINT8                       TurboPowerLimitLock;

/** Offset 0x0CBB - Package PL3 time window
  Package PL3 time window range for this policy from 0 to 64ms
**/
  UINT8                       PowerLimit3Time;

/** Offset 0x0CBC - Package PL3 Duty Cycle
  Package PL3 Duty Cycle; Valid Range is 0 to 100
**/
  UINT8                       PowerLimit3DutyCycle;

/** Offset 0x0CBD - Package PL3 Lock
  Package PL3 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
  $EN_DIS
**/
  UINT8                       PowerLimit3Lock;

/** Offset 0x0CBE - Package PL4 Lock
  Package PL4 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
  $EN_DIS
**/
  UINT8                       PowerLimit4Lock;

/** Offset 0x0CBF - TCC Activation Offset
  TCC Activation Offset. Offset from factory set TCC activation temperature at which
  the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
  Temperature, in volts.For SKL Y SKU, the recommended default for this policy is
  <b>10</b>, For all other SKUs the recommended default are <b>0</b>
**/
  UINT8                       TccActivationOffset;

/** Offset 0x0CC0 - Tcc Offset Clamp Enable/Disable
  Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
  below P1.For SKL Y SKU, the recommended default for this policy is <b>1: Enabled</b>,
  For all other SKUs the recommended default are  <b>0: Disabled</b>.
  $EN_DIS
**/
  UINT8                       TccOffsetClamp;

/** Offset 0x0CC1 - Tcc Offset Lock
  Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
  target; <b>0: Disabled</b>; 1: Enabled.
  $EN_DIS
**/
  UINT8                       TccOffsetLock;

/** Offset 0x0CC2 - Custom Ratio State Entries
  The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
  ratio table.Sets the number of custom P-states. At least 2 states must be present
**/
  UINT8                       NumberOfEntries;

/** Offset 0x0CC3 - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 1. Valid Range 0 to 128
**/
  UINT8                       Custom1PowerLimit1Time;

/** Offset 0x0CC4 - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255
**/
  UINT8                       Custom1TurboActivationRatio;

/** Offset 0x0CC5 - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom1ConfigTdpControl;

/** Offset 0x0CC6 - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 2. Valid Range 0 to 128
**/
  UINT8                       Custom2PowerLimit1Time;

/** Offset 0x0CC7 - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255
**/
  UINT8                       Custom2TurboActivationRatio;

/** Offset 0x0CC8 - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom2ConfigTdpControl;

/** Offset 0x0CC9 - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 3. Valid Range 0 to 128
**/
  UINT8                       Custom3PowerLimit1Time;

/** Offset 0x0CCA - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255
**/
  UINT8                       Custom3TurboActivationRatio;

/** Offset 0x0CCB - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom3ConfigTdpControl;

/** Offset 0x0CCC - ConfigTdp mode settings Lock
  Lock the ConfigTdp mode settings from runtime changes; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       ConfigTdpLock;

/** Offset 0x0CCD - Load Configurable TDP SSDT
  Configure whether to load Configurable TDP SSDT; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       ConfigTdpBios;

/** Offset 0x0CCE - PL1 Enable value
  PL1 Enable value to limit average platform power. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       PsysPowerLimit1;

/** Offset 0x0CCF - PL1 timewindow
  PL1 timewindow in seconds.Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16
  , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
  UINT8                       PsysPowerLimit1Time;

/** Offset 0x0CD0 - PL2 Enable Value
  PL2 Enable activates the PL2 value to limit average platform power.<b>0: Disable</b>;
  1: Enable.
  $EN_DIS
**/
  UINT8                       PsysPowerLimit2;

/** Offset 0x0CD1 - Enable or Disable MLC Streamer Prefetcher
  Enable or Disable MLC Streamer Prefetcher; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MlcStreamerPrefetcher;

/** Offset 0x0CD2 - Enable or Disable MLC Spatial Prefetcher
  Enable or Disable MLC Spatial Prefetcher; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       MlcSpatialPrefetcher;

/** Offset 0x0CD3 - Enable or Disable Monitor /MWAIT instructions
  Enable or Disable Monitor /MWAIT instructions; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MonitorMwaitEnable;

/** Offset 0x0CD4 - Enable or Disable initialization of machine check registers
  Enable or Disable initialization of machine check registers; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MachineCheckEnable;

/** Offset 0x0CD5 - AP Idle Manner of waiting for SIPI
  AP Idle Manner of waiting for SIPI; 1: HALT loop; <b>2: MWAIT loop</b>; 3: RUN loop.
  1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
  UINT8                       ApIdleManner;

/** Offset 0x0CD6 - Control on Processor Trace output scheme
  Control on Processor Trace output scheme; <b>0: Single Range Output</b>; 1: ToPA Output.
  0: Single Range Output, 1: ToPA Output
**/
  UINT8                       ProcessorTraceOutputScheme;

/** Offset 0x0CD7 - Enable or Disable Processor Trace feature
  Enable or Disable Processor Trace feature; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       ProcessorTraceEnable;

/** Offset 0x0CD8 - Enable or Disable Intel SpeedStep Technology
  Enable or Disable Intel SpeedStep Technology. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       Eist;

/** Offset 0x0CD9 - Enable or Disable Energy Efficient P-state
  Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable;
  <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnergyEfficientPState;

/** Offset 0x0CDA - Enable or Disable Energy Efficient Turbo
  Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       EnergyEfficientTurbo;

/** Offset 0x0CDB - Enable or Disable T states
  Enable or Disable T states; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       TStates;

/** Offset 0x0CDC - Enable or Disable Bi-Directional PROCHOT#
  Enable or Disable Bi-Directional PROCHOT#; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       BiProcHot;

/** Offset 0x0CDD - Enable or Disable PROCHOT# signal being driven externally
  Enable or Disable PROCHOT# signal being driven externally; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       DisableProcHotOut;

/** Offset 0x0CDE - Enable or Disable PROCHOT# Response
  Enable or Disable PROCHOT# Response; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       ProcHotResponse;

/** Offset 0x0CDF - Enable or Disable VR Thermal Alert
  Enable or Disable VR Thermal Alert; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       DisableVrThermalAlert;

/** Offset 0x0CE0 - Enable or Disable Thermal Reporting
  Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       EnableAllThermalFunctions;

/** Offset 0x0CE1 - Enable or Disable Thermal Monitor
  Enable or Disable Thermal Monitor; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       ThermalMonitor;

/** Offset 0x0CE2 - Enable or Disable CPU power states (C-states)
  Enable or Disable CPU power states (C-states). 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       Cx;

/** Offset 0x0CE3 - Configure C-State Configuration Lock
  Configure C-State Configuration Lock; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       PmgCstCfgCtrlLock;

/** Offset 0x0CE4 - Enable or Disable Enhanced C-states
  Enable or Disable Enhanced C-states. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1e;

/** Offset 0x0CE5 - Enable or Disable Package Cstate Demotion
  Enable or Disable Package Cstate Demotion. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PkgCStateDemotion;

/** Offset 0x0CE6 - Enable or Disable Package Cstate UnDemotion
  Enable or Disable Package Cstate UnDemotion. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PkgCStateUnDemotion;

/** Offset 0x0CE7 - Enable or Disable CState-Pre wake
  Enable or Disable CState-Pre wake. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       CStatePreWake;

/** Offset 0x0CE8 - Enable or Disable TimedMwait Support.
  Enable or Disable TimedMwait Support. <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       TimedMwait;

/** Offset 0x0CE9 - Enable or Disable IO to MWAIT redirection
  Enable or Disable IO to MWAIT redirection; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       CstCfgCtrIoMwaitRedirection;

/** Offset 0x0CEA - Set the Max Pkg Cstate
  Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep
  C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S ,
  6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto
**/
  UINT8                       PkgCStateLimit;

/** Offset 0x0CEB - TimeUnit for C-State Latency Control0
  TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl0TimeUnit;

/** Offset 0x0CEC - TimeUnit for C-State Latency Control1
  TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl1TimeUnit;

/** Offset 0x0CED - TimeUnit for C-State Latency Control2
  TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl2TimeUnit;

/** Offset 0x0CEE - TimeUnit for C-State Latency Control3
  TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl3TimeUnit;

/** Offset 0x0CEF - TimeUnit for C-State Latency Control4
  Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl4TimeUnit;

/** Offset 0x0CF0 - TimeUnit for C-State Latency Control5
  TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl5TimeUnit;

/** Offset 0x0CF1 - Interrupt Redirection Mode Select
  Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;7:
  No change.
**/
  UINT8                       PpmIrmSetting;

/** Offset 0x0CF2 - Lock prochot configuration
  Lock prochot configuration Enable/Disable; 0: Disable;<b> 1: Enable</b>
  $EN_DIS
**/
  UINT8                       ProcHotLock;

/** Offset 0x0CF3 - Configuration for boot TDP selection
  Configuration for boot TDP selection; <b>0: TDP Nominal</b>; 1: TDP Down; 2: TDP
  Up;0xFF : Deactivate
**/
  UINT8                       ConfigTdpLevel;

/** Offset 0x0CF4 - Max P-State Ratio
  Max P-State Ratio, Valid Range 0 to 0x7F
**/
  UINT8                       MaxRatio;

/** Offset 0x0CF5 - P-state ratios for custom P-state table
  P-state ratios for custom P-state table. NumberOfEntries has valid range between
  0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
  are configurable. Valid Range of each entry is 0 to 0x7F
**/
  UINT8                       StateRatio[40];

/** Offset 0x0D1D - P-state ratios for max 16 version of custom P-state table
  P-state ratios for max 16 version of custom P-state table. This table is used for
  OS versions limited to a max of 16 P-States. If the first entry of this table is
  0, or if Number of Entries is 16 or less, then this table will be ignored, and
  up to the top 16 values of the StateRatio table will be used instead. Valid Range
  of each entry is 0 to 0x7F
**/
  UINT8                       StateRatioMax16[16];

/** Offset 0x0D2D - Reserved
**/
  UINT8                       Reserved49;

/** Offset 0x0D2E - Platform Power Pmax
  PCODE MMIO Mailbox: Platform Power Pmax. <b>0 - Auto</b> Specified in 1/8 Watt increments.
  Range 0-1024 Watts. Value of 800 = 100W
**/
  UINT16                      PsysPmax;

/** Offset 0x0D30 - Interrupt Response Time Limit of C-State LatencyContol1
  Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl1Irtl;

/** Offset 0x0D32 - Interrupt Response Time Limit of C-State LatencyContol2
  Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl2Irtl;

/** Offset 0x0D34 - Interrupt Response Time Limit of C-State LatencyContol3
  Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl3Irtl;

/** Offset 0x0D36 - Interrupt Response Time Limit of C-State LatencyContol4
  Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl4Irtl;

/** Offset 0x0D38 - Interrupt Response Time Limit of C-State LatencyContol5
  Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl5Irtl;

/** Offset 0x0D3A - Reserved
**/
  UINT8                       Reserved50[2];

/** Offset 0x0D3C - Package Long duration turbo mode power limit
  Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
  Valid Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit1;

/** Offset 0x0D40 - Package Short duration turbo mode power limit
  Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit2Power;

/** Offset 0x0D44 - Package PL3 power limit
  Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit3;

/** Offset 0x0D48 - Package PL4 power limit
  Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit4;

/** Offset 0x0D4C - Tcc Offset Time Window for RATL
  Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      TccOffsetTimeWindowForRatl;

/** Offset 0x0D50 - Short term Power Limit value for custom cTDP level 1
  Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom1PowerLimit1;

/** Offset 0x0D54 - Long term Power Limit value for custom cTDP level 1
  Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom1PowerLimit2;

/** Offset 0x0D58 - Short term Power Limit value for custom cTDP level 2
  Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom2PowerLimit1;

/** Offset 0x0D5C - Long term Power Limit value for custom cTDP level 2
  Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom2PowerLimit2;

/** Offset 0x0D60 - Short term Power Limit value for custom cTDP level 3
  Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom3PowerLimit1;

/** Offset 0x0D64 - Long term Power Limit value for custom cTDP level 3
  Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom3PowerLimit2;

/** Offset 0x0D68 - Platform PL1 power
  Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
  0 to 4095875 in Step size of 125
**/
  UINT32                      PsysPowerLimit1Power;

/** Offset 0x0D6C - Platform PL2 power
  Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
  0 to 4095875 in Step size of 125
**/
  UINT32                      PsysPowerLimit2Power;

/** Offset 0x0D70 - Race To Halt
  Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
  in order to enter pkg C-State faster to reduce overall power. (RTH is controlled
  through MSR 1FC bit 20)Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       RaceToHalt;

/** Offset 0x0D71 - Set Three Strike Counter Disable
  False (default): Three Strike counter will be incremented and True: Prevents Three
  Strike counter from incrementing; <b>0: False</b>; 1: True.
  0: False, 1: True
**/
  UINT8                       ThreeStrikeCounterDisable;

/** Offset 0x0D72 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
  Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       HwpInterruptControl;

/** Offset 0x0D73 - Reserved
**/
  UINT8                       Reserved51[4];

/** Offset 0x0D77 - Intel Turbo Boost Max Technology 3.0
  Intel Turbo Boost Max Technology 3.0. 0: Disabled; <b>1: Enabled</b>
  $EN_DIS
**/
  UINT8                       EnableItbm;

/** Offset 0x0D78 - Enable or Disable C1 Cstate Demotion
  Enable or Disable C1 Cstate Demotion. Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1StateAutoDemotion;

/** Offset 0x0D79 - Enable or Disable C1 Cstate UnDemotion
  Enable or Disable C1 Cstate UnDemotion. Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1StateUnDemotion;

/** Offset 0x0D7A - Minimum Ring ratio limit override
  Minimum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
  ratio limit
**/
  UINT8                       MinRingRatioLimit;

/** Offset 0x0D7B - Maximum Ring ratio limit override
  Maximum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
  ratio limit
**/
  UINT8                       MaxRingRatioLimit;

/** Offset 0x0D7C - Enable or Disable Per Core P State OS control
  Enable or Disable Per Core P State OS control. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnablePerCorePState;

/** Offset 0x0D7D - Enable or Disable HwP Autonomous Per Core P State OS control
  Enable or Disable HwP Autonomous Per Core P State OS control. 0: Disable; <b>1:
  Enable</b>
  $EN_DIS
**/
  UINT8                       EnableHwpAutoPerCorePstate;

/** Offset 0x0D7E - Enable or Disable HwP Autonomous EPP Grouping
  Enable or Disable HwP Autonomous EPP Grouping. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnableHwpAutoEppGrouping;

/** Offset 0x0D7F - Enable or Disable EPB override over PECI
  Enable or Disable EPB override over PECI. <b>0: Disable;</b> 1: Enable
  $EN_DIS
**/
  UINT8                       EnableEpbPeciOverride;

/** Offset 0x0D80 - Enable or Disable Fast MSR for IA32_HWP_REQUEST
  Enable or Disable Fast MSR for IA32_HWP_REQUEST. 0: Disable;<b> 1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnableFastMsrHwpReq;

/** Offset 0x0D81 - Enable Configurable TDP
  Applies TDP initialization settings based on non-cTDP or cTDP.; 0: Applies to non-cTDP;
  <b>1: Applies to cTDP</b>
  $EN_DIS
**/
  UINT8                       ApplyConfigTdp;

/** Offset 0x0D82 - Reserved
**/
  UINT8                       Reserved52;

/** Offset 0x0D83 - Dual Tau Boost
  Enable, Disable Dual Tau Boost feature. This is only applicable for Desktop; <b>0:
  Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       DualTauBoost;

/** Offset 0x0D84 - Reserved
**/
  UINT8                       Reserved53[32];

/** Offset 0x0DA4 - End of Post message
  Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
  EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE
  0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
  UINT8                       EndOfPostMessage;

/** Offset 0x0DA5 - D0I3 Setting for HECI Disable
  Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
  HECI devices
  $EN_DIS
**/
  UINT8                       DisableD0I3SettingForHeci;

/** Offset 0x0DA6 - Mctp Broadcast Cycle
  Test, Determine if MCTP Broadcast is enabled <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       MctpBroadcastCycle;

/** Offset 0x0DA7 - Enable LOCKDOWN SMI
  Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
  $EN_DIS
**/
  UINT8                       PchLockDownGlobalSmi;

/** Offset 0x0DA8 - Enable LOCKDOWN BIOS Interface
  Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosInterface;

/** Offset 0x0DA9 - Unlock all GPIO pads
  Force all GPIO pads to be unlocked for debug purpose.
  $EN_DIS
**/
  UINT8                       PchUnlockGpioPads;

/** Offset 0x0DAA - PCH Unlock SideBand access
  The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before
  3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access.
  $EN_DIS
**/
  UINT8                       PchSbAccessUnlock;

/** Offset 0x0DAB - Reserved
**/
  UINT8                       Reserved54;

/** Offset 0x0DAC - PCIE RP Ltr Max Snoop Latency
  Latency Tolerance Reporting, Max Snoop Latency.
**/
  UINT16                      PcieRpLtrMaxSnoopLatency[28];

/** Offset 0x0DE4 - PCIE RP Ltr Max No Snoop Latency
  Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
  UINT16                      PcieRpLtrMaxNoSnoopLatency[28];

/** Offset 0x0E1C - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       PcieRpSnoopLatencyOverrideMode[28];

/** Offset 0x0E38 - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       PcieRpSnoopLatencyOverrideMultiplier[28];

/** Offset 0x0E54 - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      PcieRpSnoopLatencyOverrideValue[28];

/** Offset 0x0E8C - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       PcieRpNonSnoopLatencyOverrideMode[28];

/** Offset 0x0EA8 - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       PcieRpNonSnoopLatencyOverrideMultiplier[28];

/** Offset 0x0EC4 - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      PcieRpNonSnoopLatencyOverrideValue[28];

/** Offset 0x0EFC - PCIE RP Slot Power Limit Scale
  Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
  UINT8                       PcieRpSlotPowerLimitScale[28];

/** Offset 0x0F18 - PCIE RP Slot Power Limit Value
  Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
  UINT16                      PcieRpSlotPowerLimitValue[28];

/** Offset 0x0F50 - PCIE RP Enable Port8xh Decode
  This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
  1: Enable.
  $EN_DIS
**/
  UINT8                       PcieEnablePort8xhDecode;

/** Offset 0x0F51 - PCIE Port8xh Decode Port Index
  The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
  UINT8                       PchPciePort8xhDecodePortIndex;

/** Offset 0x0F52 - PCH Energy Reporting
  Disable/Enable PCH to CPU energy report feature.
  $EN_DIS
**/
  UINT8                       PchPmDisableEnergyReport;

/** Offset 0x0F53 - PCH Sata Test Mode
  Allow entrance to the PCH SATA test modes.
  $EN_DIS
**/
  UINT8                       SataTestMode;

/** Offset 0x0F54 - PCH USB OverCurrent mapping lock enable
  If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
  that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
  $EN_DIS
**/
  UINT8                       PchXhciOcLock;

/** Offset 0x0F55 - LpmStateEnableMask
**/
  UINT8                       LpmStateEnableMask;

/** Offset 0x0F56 - PCIE RP Ltr Max Snoop Latency
  Latency Tolerance Reporting, Max Snoop Latency.
**/
  UINT16                      CpuPcieRpLtrMaxSnoopLatency[4];

/** Offset 0x0F5E - PCIE RP Ltr Max No Snoop Latency
  Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
  UINT16                      CpuPcieRpLtrMaxNoSnoopLatency[4];

/** Offset 0x0F66 - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       CpuPcieRpSnoopLatencyOverrideMode[4];

/** Offset 0x0F6A - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       CpuPcieRpSnoopLatencyOverrideMultiplier[4];

/** Offset 0x0F6E - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      CpuPcieRpSnoopLatencyOverrideValue[4];

/** Offset 0x0F76 - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       CpuPcieRpNonSnoopLatencyOverrideMode[4];

/** Offset 0x0F7A - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       CpuPcieRpNonSnoopLatencyOverrideMultiplier[4];

/** Offset 0x0F7E - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      CpuPcieRpNonSnoopLatencyOverrideValue[4];

/** Offset 0x0F86 - PCIE RP Upstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen3Uptp[4];

/** Offset 0x0F8A - PCIE RP Downstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen3Dptp[4];

/** Offset 0x0F8E - PCIE RP Upstream Port Transmiter Preset
  Used during Gen4 Link Equalization. Used for all lanes.  Default is 8.
**/
  UINT8                       CpuPcieRpGen4Uptp[4];

/** Offset 0x0F92 - PCIE RP Downstream Port Transmiter Preset
  Used during Gen4 Link Equalization. Used for all lanes.  Default is 9.
**/
  UINT8                       CpuPcieRpGen4Dptp[4];

/** Offset 0x0F96 - Reserved
**/
  UINT8                       Reserved55[16];

/** Offset 0x0FA6 - FOMS Control Policy
  Choose the Foms Control Policy, <b>Default = 0 </b>
  0: Auto, 1: Gen3 Foms, 2: Gen4 Foms, 3: Gen3 and Gen4 Foms
**/
  UINT8                       CpuPcieFomsCp[4];

/** Offset 0x0FAA - PMC C10 dynamic threshold dajustment enable
  Set if you want to enable PMC C10 dynamic threshold adjustment. Only works on supported SKUs
  $EN_DIS
**/
  UINT8                       PmcC10DynamicThresholdAdjustment;

/** Offset 0x0FAB - P2P mode for PCIE RP
  Enable/disable peer to peer mode for PCIE Root Ports. 0: Disable, 1: Enable.
  0: Disable, 1: Enable
**/
  UINT8                       CpuPcieRpPeerToPeerMode[4];

/** Offset 0x0FAF - Reserved
**/
  UINT8                       Reserved56[33];

/** Offset 0x0FD0 - FspEventHandler
  <b>Optional</b> pointer to the boot loader's implementation of FSP_EVENT_HANDLER.
**/
  UINT32                      FspEventHandler;

/** Offset 0x0FD4 - Enable VMD Global Mapping
  Enable/disable to VMD controller.0: Disable; 1: Enable(Default)
  $EN_DIS
**/
  UINT8                       VmdGlobalMapping;

/** Offset 0x0FD5 - Reserved
**/
  UINT8                       Reserved57[11];
} FSP_S_CONFIG;

/** Fsp S UPD Configuration
**/
typedef struct {

/** Offset 0x0000
**/
  FSP_UPD_HEADER              FspUpdHeader;

/** Offset 0x0020
**/
  FSPS_ARCH_UPD               FspsArchUpd;

/** Offset 0x0040
**/
  FSP_S_CONFIG                FspsConfig;

/** Offset 0x0FE0
**/
  UINT8                       UnusedUpdSpace40[6];

/** Offset 0x0FE6
**/
  UINT16                      UpdTerminator;
} FSPS_UPD;

#pragma pack()

#endif