blob: 624f967fecd0efc54e25943ab212dbce418e904d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/** @file
Master header file for SecCore.
Copyright (c) 2013, Intel Corporation. All rights reserved.<BR>
SPDX-License-Identifier: BSD-2-Clause-Patent
**/
#ifndef _SEC_CORE_H_
#define _SEC_CORE_H_
#include <PiPei.h>
#include <Ppi/SecPlatformInformation.h>
#include <Ppi/TemporaryRamSupport.h>
#include <Library/BaseLib.h>
#include <Library/DebugLib.h>
#include <Library/PcdLib.h>
#include <Library/BaseMemoryLib.h>
#include <Library/UefiCpuLib.h>
#include <Library/PeCoffGetEntryPointLib.h>
#include <Library/PeCoffExtraActionLib.h>
#include <Library/DebugAgentLib.h>
#define SEC_IDT_ENTRY_COUNT 34
typedef struct _SEC_IDT_TABLE {
//
// Reserved 8 bytes preceding IDT to store EFI_PEI_SERVICES**, since IDT base
// address should be 8-byte alignment.
// Note: For IA32, only the 4 bytes immediately preceding IDT is used to store
// EFI_PEI_SERVICES**
//
UINT64 PeiService;
UINT64 IdtTable[SEC_IDT_ENTRY_COUNT];
} SEC_IDT_TABLE;
/**
Switch the stack in the temporary memory to the one in the permanent memory.
This function must be invoked after the memory migration immediately. The relative
position of the stack in the temporary and permanent memory is same.
@param TemporaryMemoryBase Base address of the temporary memory.
@param PermenentMemoryBase Base address of the permanent memory.
**/
VOID
EFIAPI
SecSwitchStack (
UINT32 TemporaryMemoryBase,
UINT32 PermenentMemoryBase
);
/**
This service of the TEMPORARY_RAM_SUPPORT_PPI that migrates temporary RAM into
permanent memory.
@param PeiServices Pointer to the PEI Services Table.
@param TemporaryMemoryBase Source Address in temporary memory from which the SEC or PEIM will copy the
Temporary RAM contents.
@param PermanentMemoryBase Destination Address in permanent memory into which the SEC or PEIM will copy the
Temporary RAM contents.
@param CopySize Amount of memory to migrate from temporary to permanent memory.
@retval EFI_SUCCESS The data was successfully returned.
@retval EFI_INVALID_PARAMETER PermanentMemoryBase + CopySize > TemporaryMemoryBase when
TemporaryMemoryBase > PermanentMemoryBase.
**/
EFI_STATUS
EFIAPI
SecTemporaryRamSupport (
IN CONST EFI_PEI_SERVICES **PeiServices,
IN EFI_PHYSICAL_ADDRESS TemporaryMemoryBase,
IN EFI_PHYSICAL_ADDRESS PermanentMemoryBase,
IN UINTN CopySize
);
/**
Entry point to the C language phase of SEC. After the SEC assembly
code has initialized some temporary memory and set up the stack,
the control is transferred to this function.
@param SizeOfRam Size of the temporary memory available for use.
@param TempRamBase Base address of temporary ram
@param BootFirmwareVolume Base address of the Boot Firmware Volume.
**/
VOID
EFIAPI
SecStartup (
IN UINT32 SizeOfRam,
IN UINT32 TempRamBase,
IN VOID *BootFirmwareVolume
);
/**
Find and return Pei Core entry point.
It also find SEC and PEI Core file debug information. It will report them if
remote debug is enabled.
@param BootFirmwareVolumePtr Point to the boot firmware volume.
@param PeiCoreEntryPoint Point to the PEI core entry point.
**/
VOID
EFIAPI
FindAndReportEntryPoints (
IN EFI_FIRMWARE_VOLUME_HEADER *BootFirmwareVolumePtr,
OUT EFI_PEI_CORE_ENTRY_POINT *PeiCoreEntryPoint
);
/**
Autogenerated function that calls the library constructors for all of the module's
dependent libraries. This function must be called by the SEC Core once a stack has
been established.
**/
VOID
EFIAPI
ProcessLibraryConstructorList (
VOID
);
#endif
|