path: root/MdeModulePkg/MdeModulePkg.dec

## @file  MdeModulePkg.dec
# This package provides the modules that conform to UEFI/PI Industry standards.
# It also provides the definitions(including PPIs/PROTOCOLs/GUIDs and library classes)
# and libraries instances, which are used for those modules.
#
# Copyright (c) 2007 - 2014, Intel Corporation. All rights reserved.<BR>
# This program and the accompanying materials are licensed and made available under 
# the terms and conditions of the BSD License that accompanies this distribution.  
# The full text of the license may be found at
# http://opensource.org/licenses/bsd-license.php.                                                                          
# 
# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,                     
# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.  
#
##


[Defines]
  DEC_SPECIFICATION              = 0x00010005
  PACKAGE_NAME                   = MdeModulePkg
  PACKAGE_UNI_FILE               = MdeModulePkg.uni
  PACKAGE_GUID                   = BA0D78D6-2CAF-414b-BD4D-B6762A894288
  PACKAGE_VERSION                = 0.94

[Includes]
  Include


[LibraryClasses]
  ##  @libraryclass  IpIo layer upon EFI IP4 Protocol.
  #   This library is only intended to be used by UEFI network stack modules.
  IpIoLib|Include/Library/IpIoLib.h

  ##  @libraryclass  Basic function for UEFI network stack.
  #   This library is only intended to be used by UEFI network stack modules.
  NetLib|Include/Library/NetLib.h

  ##  @libraryclass  The helper routines to access UDP service.
  #   This library is only intended to be used by UEFI network stack modules.
  UdpIoLib|Include/Library/UdpIoLib.h

  ##  @libraryclass  The helper routines to access TCP service.
  #   This library is only intended to be used by UEFI network stack modules.
  TcpIoLib|Include/Library/TcpIoLib.h

  ##  @libraryclass  Defines a set of methods to reset whole system.
  ResetSystemLib|Include/Library/ResetSystemLib.h

  ##  @libraryclass  Defines a set of methods related do S3 mode.
  #   This library class is no longer used and modules using this library should
  #   directly locate EFI_PEI_S3_RESUME_PPI defined in PI 1.2 specification.
  S3Lib|Include/Library/S3Lib.h

  ##  @libraryclass  Defines a set of methods related recovery mode.
  #   This library class is no longer used and modules using this library should
  #   directly locate EFI_PEI_RECOVERY_MODULE_PPI defined in PI 1.2 specification.
  RecoveryLib|Include/Library/RecoveryLib.h

  ##  @libraryclass  Provides HII related functions.
  HiiLib|Include/Library/HiiLib.h

  ##  @libraryclass  Defines a set of interfaces on how to process capusle image update.
  CapsuleLib|Include/Library/CapsuleLib.h

  ##  @libraryclass  Library for Deferred Procedure Calls.
  DpcLib|Include/Library/DpcLib.h

  ##  @libraryclass    Provides global variables that are pointers
  #   to the UEFI HII related protocols.
  #
  UefiHiiServicesLib|Include/Library/UefiHiiServicesLib.h

  ##  @libraryclass    Provides a set of interfaces to abstract the policy of security measurement.
  #
  SecurityManagementLib|Include/Library/SecurityManagementLib.h

  ##  @libraryclass  OEM status code libary is used to report status code to OEM device.
  #
  OemHookStatusCodeLib|Include/Library/OemHookStatusCodeLib.h

  ##  @libraryclass  Debug Agent is used to provide soft debug capability.
  #
  DebugAgentLib|Include/Library/DebugAgentLib.h

  ##  @libraryclass  Provide platform specific hooks.
  #
  PlatformHookLib|Include/Library/PlatformHookLib.h

  ##  @libraryclass  Provide platform specific hooks for SMM core.
  #
  SmmCorePlatformHookLib|Include/Library/SmmCorePlatformHookLib.h

  ##  @libraryclass  Provide capability to maintain the data integrity cross S3 phase.
  #
  LockBoxLib|Include/Library/LockBoxLib.h
  
  ##  @libraryclass  Provide the CPU exception handler.
  #
  CpuExceptionHandlerLib|Include/Library/CpuExceptionHandlerLib.h
  
  ##  @libraryclass    Provides platform specific display interface.
  #
  CustomizedDisplayLib|Include/Library/CustomizedDisplayLib.h

[Guids]
  ## MdeModule package token space guid
  # Include/Guid/MdeModulePkgTokenSpace.h
  gEfiMdeModulePkgTokenSpaceGuid       = { 0xA1AFF049, 0xFDEB, 0x442a, { 0xB3, 0x20, 0x13, 0xAB, 0x4C, 0xB7, 0x2B, 0xBC }}

  ## Hob guid for Pcd DataBase
  #  Include/Guid/PcdDataBaseHobGuid.h
  gPcdDataBaseHobGuid            = { 0xEA296D92, 0x0B69, 0x423C, { 0x8C, 0x28, 0x33, 0xB4, 0xE0, 0xA9, 0x12, 0x68 }}

  ## Guid for PCD DataBase signature.
  # Include/Guid/PcdDataBaseSignatureGuid.h
  gPcdDataBaseSignatureGuid = { 0x3c7d193c, 0x682c, 0x4c14, { 0xa6, 0x8f, 0x55, 0x2d, 0xea, 0x4f, 0x43, 0x7e }}

  ## Guid for EDKII implementation GUIDed opcodes
  #  Include/Guid/MdeModuleHii.h
  gEfiIfrTianoGuid      = { 0xf0b1735, 0x87a0, 0x4193, {0xb2, 0x66, 0x53, 0x8c, 0x38, 0xaf, 0x48, 0xce }}

  ## Guid for Framework vfr GUIDed opcodes.
  #  Include/Guid/MdeModuleHii.h
  gEfiIfrFrameworkGuid  = { 0x31ca5d1a, 0xd511, 0x4931, { 0xb7, 0x82, 0xae, 0x6b, 0x2b, 0x17, 0x8c, 0xd7 }}

  ## Guid to specify the System Non Volatile FV
  #  Include/Guid/SystemNvDataGuid.h
  gEfiSystemNvDataFvGuid         = { 0xFFF12B8D, 0x7696, 0x4C8B, { 0xA9, 0x85, 0x27, 0x47, 0x07, 0x5B, 0x4F, 0x50 }}

  ## GUID used as the signature of FTW working block header.
  #  Include/Guid/SystemNvDataGuid.h
  gEdkiiWorkingBlockSignatureGuid   = { 0x9e58292b, 0x7c68, 0x497d, { 0xa0, 0xce, 0x65,  0x0, 0xfd, 0x9f, 0x1b, 0x95 }}

  ## GUID used to build FTW last write data hob and install PPI to inform the check for FTW last write data has been done.
  #  Include/Guid/FaultTolerantWrite.h
  gEdkiiFaultTolerantWriteGuid      = { 0x1d3e9cb8, 0x43af, 0x490b, { 0x83,  0xa, 0x35, 0x16, 0xaa, 0x53, 0x20, 0x47 }}

  ## Guid specify the device is the console out device.
  #  Include/Guid/ConsoleOutDevice.h
  gEfiConsoleOutDeviceGuid       = { 0xD3B36F2C, 0xD551, 0x11D4, { 0x9A, 0x46, 0x00, 0x90, 0x27, 0x3F, 0xC1, 0x4D }}

  ## Guid specify the device is the console in device.
  #  Include/Guid/ConsoleInDevice.h
  gEfiConsoleInDeviceGuid        = { 0xD3B36F2B, 0xD551, 0x11D4, { 0x9A, 0x46, 0x00, 0x90, 0x27, 0x3F, 0xC1, 0x4D }}

  ## Hob and Variable guid specify the platform memory type information.
  #  Include/Guid/MemoryTypeInformation.h
  gEfiMemoryTypeInformationGuid  = { 0x4C19049F, 0x4137, 0x4DD3, { 0x9C, 0x10, 0x8B, 0x97, 0xA8, 0x3F, 0xFD, 0xFA }}

  ## Capsule update hob and variable guid
  #  Include/Guid/CapsuleVendor.h
  gEfiCapsuleVendorGuid          = { 0x711C703F, 0xC285, 0x4B10, { 0xA3, 0xB0, 0x36, 0xEC, 0xBD, 0x3C, 0x8B, 0xE2 }}

  ## Guid specifiy the device is the StdErr device.
  #  Include/Guid/StandardErrorDevice.h
  gEfiStandardErrorDeviceGuid    = { 0xD3B36F2D, 0xD551, 0x11D4, { 0x9A, 0x46, 0x00, 0x90, 0x27, 0x3F, 0xC1, 0x4D }}

  ## Guid acted as variable store header's signature and to specify the variable list entries put in the EFI system table.
  #  Include/Guid/VariableFormat.h
  gEfiVariableGuid           = { 0xddcf3616, 0x3275, 0x4164, { 0x98, 0xb6, 0xfe, 0x85, 0x70, 0x7f, 0xfe, 0x7d }}

  #  Include/Guid/VariableIndexTable.h
  gEfiVariableIndexTableGuid  = { 0x8cfdb8c8, 0xd6b2, 0x40f3, { 0x8e, 0x97, 0x02, 0x30, 0x7c, 0xc9, 0x8b, 0x7c }}

  ## Guid is defined for SMM variable module to notify SMM variable wrapper module when variable write service was ready.
  #  Include/Guid/SmmVariableCommon.h
  gSmmVariableWriteGuid  = { 0x93ba1826, 0xdffb, 0x45dd, { 0x82, 0xa7, 0xe7, 0xdc, 0xaa, 0x3b, 0xbd, 0xf3 }}
  
  ## Performance protocol guid that also acts as the performance HOB guid and performance variable GUID
  #  Include/Guid/Performance.h
  gPerformanceProtocolGuid       = { 0x76B6BDFA, 0x2ACD, 0x4462, { 0x9E, 0x3F, 0xCB, 0x58, 0xC9, 0x69, 0xD9, 0x37 } }
  gSmmPerformanceProtocolGuid    = { 0xf866226a, 0xeaa5, 0x4f5a, { 0xa9, 0xa,  0x6c, 0xfb, 0xa5, 0x7c, 0x58, 0x8e } }
  gPerformanceExProtocolGuid     = { 0x1ea81bec, 0xf01a, 0x4d98, { 0xa2, 0x1,  0x4a, 0x61, 0xce, 0x2f, 0xc0, 0x22 } }
  gSmmPerformanceExProtocolGuid  = { 0x931fc048, 0xc71d, 0x4455, { 0x89, 0x30, 0x47, 0x6,  0x30, 0xe3, 0xe,  0xe5 } }

  ## Guid is defined for CRC32 encapsulation scheme.
  #  Include/Guid/Crc32GuidedSectionExtraction.h
  gEfiCrc32GuidedSectionExtractionGuid = { 0xFC1BCDB0, 0x7D31, 0x49aa, {0x93, 0x6A, 0xA4, 0x60, 0x0D, 0x9D, 0xD0, 0x83 } }

  ## Include/Guid/NicIp4ConfigNvData.h
  gEfiNicIp4ConfigVariableGuid   = {0xd8944553, 0xc4dd, 0x41f4, { 0x9b, 0x30, 0xe1, 0x39, 0x7c, 0xfb, 0x26, 0x7b }}

  ## Include/Guid/StatusCodeCallbackGuid.h
  gStatusCodeCallbackGuid   = {0xe701458c, 0x4900, 0x4ca5, {0xb7, 0x72, 0x3d, 0x37, 0x94, 0x9f, 0x79, 0x27}}

  ## GUID identifies status code records HOB that originate from the PEI status code
  #  Include/Guid/MemoryStatusCodeRecord.h
  gMemoryStatusCodeRecordGuid     = { 0x060CC026, 0x4C0D, 0x4DDA, { 0x8F, 0x41, 0x59, 0x5F, 0xEF, 0x00, 0xA5, 0x02 }}

  ## GUID used to pass DEBUG() macro information through the Status Code Protocol and Status Code PPI
  #  Include/Guid/StatusCodeDataTypeDebug.h
  gEfiStatusCodeDataTypeDebugGuid  = { 0x9A4E9246, 0xD553, 0x11D5, { 0x87, 0xE2, 0x00, 0x06, 0x29, 0x45, 0xC3, 0xB9 }}

  ##  A configuration Table Guid for Load module at fixed address 
  #  Include/Guid/LoadModuleAtFixedAddress.h
  gLoadFixedAddressConfigurationTableGuid  = { 0x2CA88B53,0xD296,0x4080, { 0xA4,0xA5,0xCA,0xD9,0xBA,0xE2,0x4B,0x9 } }

  ## GUID used to store the global debug mask value into an EFI Variable
  # Include/Guid/DebugMask.h  
  gEfiGenericVariableGuid = { 0x59d1c24f, 0x50f1, 0x401a, {0xb1, 0x01, 0xf3, 0x3e, 0x0d, 0xae, 0xd4, 0x43} }
  
  ##  Event for the DXE Core to signal idle events
  #  Include/Guid/EventIdle.h
  gIdleLoopEventGuid  = { 0x3c8d294c, 0x5fc3, 0x4451, { 0xbb, 0x31, 0xc4, 0xc0, 0x32, 0x29, 0x5e, 0x6c } }

  ## Include/Guid/RecoveryDevice.h
  gRecoveryOnFatUsbDiskGuid          = { 0x0FFBCE19, 0x324C, 0x4690, { 0xA0, 0x09, 0x98, 0xC6, 0xAE, 0x2E, 0xB1, 0x86 }}

  ## Include/Guid/RecoveryDevice.h
  gRecoveryOnFatIdeDiskGuid          = { 0xB38573B6, 0x6200, 0x4AC5, { 0xB5, 0x1D, 0x82, 0xE6, 0x59, 0x38, 0xD7, 0x83 }}

  ## Include/Guid/RecoveryDevice.h
  gRecoveryOnFatFloppyDiskGuid       = { 0x2E3D2E75, 0x9B2E, 0x412D, { 0xB4, 0xB1, 0x70, 0x41, 0x6B, 0x87, 0x00, 0xFF }}

  ## Include/Guid/RecoveryDevice.h
  gRecoveryOnDataCdGuid              = { 0x5CAC0099, 0x0DC9, 0x48E5, { 0x80, 0x68, 0xBB, 0x95, 0xF5, 0x40, 0x0A, 0x9F }}

  ## Include/Guid/SmmLockBox.h
  gEfiSmmLockBoxCommunicationGuid    = { 0x2a3cfebd, 0x27e8, 0x4d0a, { 0x8b, 0x79, 0xd6, 0x88, 0xc2, 0xa3, 0xe1, 0xc0 }}

  ## Include/Guid/AcpiS3Context.h
  gEfiAcpiVariableGuid               = { 0xAF9FFD67, 0xEC10, 0x488A, { 0x9D, 0xFC, 0x6C, 0xBF, 0x5E, 0xE2, 0x2C, 0x2E }}

  ## Include/Guid/AcpiS3Context.h
  gEfiAcpiS3ContextGuid              = { 0xef98d3a, 0x3e33, 0x497a, { 0xa4, 0x1, 0x77, 0xbe, 0x3e, 0xb7, 0x4f, 0x38 }}

  ## Include/Guid/BootScriptExecutorVariable.h
  gEfiBootScriptExecutorVariableGuid = { 0x3079818c, 0x46d4, 0x4a73, { 0xae, 0xf3, 0xe3, 0xe4, 0x6c, 0xf1, 0xee, 0xdb }}
  gEfiBootScriptExecutorContextGuid  = { 0x79cb58c4, 0xac51, 0x442f, { 0xaf, 0xd7, 0x98, 0xe4, 0x7d, 0x2e, 0x99, 0x8 }}

  ## Include/Guid/UsbKeyBoardLayout.h
  gUsbKeyboardLayoutPackageGuid      = { 0xc0f3b43, 0x44de, 0x4907, { 0xb4, 0x78, 0x22, 0x5f, 0x6f, 0x62, 0x89, 0xdc }}
  gUsbKeyboardLayoutKeyGuid          = { 0x3a4d7a7c, 0x18a, 0x4b42, { 0x81, 0xb3, 0xdc, 0x10, 0xe3, 0xb5, 0x91, 0xbd }}
  
  ## Include/Guid/HiiResourceSampleHii.h
  gHiiResourceSamleFormSetGuid       = { 0x4f4ef7f0, 0xaa29, 0x4ce9, { 0xba, 0x41, 0x64, 0x3e, 0x1, 0x23, 0xa9, 0x9f }}

  ## Include/Guid/DriverSampleHii.h
  gDriverSampleFormSetGuid           = { 0xA04A27f4, 0xDF00, 0x4D42, { 0xB5, 0x52, 0x39, 0x51, 0x13, 0x02, 0x11, 0x3D }}
  gDriverSampleInventoryGuid         = { 0xb3f56470, 0x6141, 0x4621, { 0x8f, 0x19, 0x70, 0x4e, 0x57, 0x7a, 0xa9, 0xe8 }}
  gEfiIfrRefreshIdOpGuid             = { 0xF5E655D9, 0x02A6, 0x46f2, { 0x9E, 0x76, 0xB8, 0xBE, 0x8E, 0x60, 0xAB, 0x22 }}

  ## Include/Guid/PlatDriOverrideHii.h
  gPlatformOverridesManagerGuid      = { 0x8614567d, 0x35be, 0x4415, { 0x8d, 0x88, 0xbd, 0x7d, 0xc, 0x9c, 0x70, 0xc0 }}

  ## Include/Guid/Ip4ConfigHii.h
  gNicIp4ConfigNvDataGuid            = { 0x9d5b53f, 0xf4b0, 0x4f59, { 0xa0, 0xb1, 0x7b, 0x57, 0xd3, 0x5c, 0xe, 0x5 }}

  ## Include/Guid/VlanConfigHii.h
  gVlanConfigFormSetGuid             = { 0xd79df6b0, 0xef44, 0x43bd, { 0x97, 0x97, 0x43, 0xe9, 0x3b, 0xcf, 0x5f, 0xa8 }}

  ## Include/Guid/Ip4IScsiConfigHii.h
  gIp4IScsiConfigGuid                = { 0x6456ed61, 0x3579, 0x41c9, { 0x8a, 0x26, 0x0a, 0x0b, 0xd6, 0x2b, 0x78, 0xfc }}
  gIScsiCHAPAuthInfoGuid             = { 0x786ec0ac, 0x65ae, 0x4d1b, { 0xb1, 0x37, 0xd, 0x11, 0xa, 0x48, 0x37, 0x97 }}

  ## Include/Guid/ZeroGuid.h
  gZeroGuid                          = { 0x0, 0x0, 0x0, {0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}}
  
  ## Include/Guid/MtcVendor.h
  gMtcVendorGuid                     = { 0xeb704011, 0x1402, 0x11d3, { 0x8e, 0x77, 0x0, 0xa0, 0xc9, 0x69, 0x72, 0x3b }}

  ## Guid for Firmware Performance Data Table (FPDT) implementation.
  #  Include/Guid/FirmwarePerformance.h
  gEfiFirmwarePerformanceGuid        = { 0xc095791a, 0x3001, 0x47b2, { 0x80, 0xc9, 0xea, 0xc7, 0x31, 0x9f, 0x2f, 0xa4 }}
  gFirmwarePerformanceS3PointerGuid  = { 0xdc65adc,  0xa973, 0x4130, { 0x8d, 0xf0, 0x2a, 0xdb, 0xeb, 0x9e, 0x4a, 0x31 }}

  ## Include/Guid/ExitBootServiceFailed.h
  gEventExitBootServicesFailedGuid   = { 0x4f6c5507, 0x232f, 0x4787, { 0xb9, 0x5e, 0x72, 0xf8, 0x62, 0x49, 0xc, 0xb1 } }

  ## Include/Guid/ConnectConInEvent.h
  gConnectConInEventGuid             = { 0xdb4e8151, 0x57ed, 0x4bed, { 0x88, 0x33, 0x67, 0x51, 0xb5, 0xd1, 0xa8, 0xd7 }}

  ## Include/Guid/StatusCodeDataTypeVariable.h
  gEdkiiStatusCodeDataTypeVariableGuid = { 0xf6ee6dbb, 0xd67f, 0x4ea0, { 0x8b, 0x96, 0x6a, 0x71, 0xb1, 0x9d, 0x84, 0xad }}

[Ppis]
  ## Include/Ppi/AtaController.h
  gPeiAtaControllerPpiGuid       = { 0xa45e60d1, 0xc719, 0x44aa, { 0xb0, 0x7a, 0xaa, 0x77, 0x7f, 0x85, 0x90, 0x6d }}

  ## Include/Ppi/UsbHostController.h
  gPeiUsbHostControllerPpiGuid   = { 0x652B38A9, 0x77F4, 0x453F, { 0x89, 0xD5, 0xE7, 0xBD, 0xC3, 0x52, 0xFC, 0x53 }}

  ## Include/Ppi/Usb2HostController.h
  gPeiUsb2HostControllerPpiGuid  = { 0xfedd6305, 0xe2d7, 0x4ed5, { 0x9f, 0xaa, 0xda, 0x8, 0xe, 0x33, 0x6c, 0x22   }}

  ## Include/Ppi/UsbController.h
  gPeiUsbControllerPpiGuid       = { 0x3BC1F6DE, 0x693E, 0x4547, { 0xA3, 0x00, 0x21, 0x82, 0x3C, 0xA4, 0x20, 0xB2 }}

  ## Include/Ppi/UsbIo.h
  gPeiUsbIoPpiGuid               = { 0x7C29785C, 0x66B9, 0x49FC, { 0xB7, 0x97, 0x1C, 0xA5, 0x55, 0x0E, 0xF2, 0x83 }}

  ## Include/Ppi/Capsule.h
  gPeiCapsulePpiGuid             = { 0x3acf33ee, 0xd892, 0x40f4, { 0xa2, 0xfc, 0x38, 0x54, 0xd2, 0xe1, 0x32, 0x3d }}

  ## Include/Ppi/SecPerformance.h
  gPeiSecPerformancePpiGuid      = { 0x0ecc666b, 0x4662, 0x47f9, { 0x9d, 0xd5, 0xd0, 0x96, 0xff, 0x7d, 0xa4, 0x9e }}

  ## Include/Ppi/SmmCommunication.h
  gEfiPeiSmmCommunicationPpiGuid   =  { 0xae933e1c, 0xcc47, 0x4e38, { 0x8f, 0xe, 0xe2, 0xf6, 0x1d, 0x26, 0x5, 0xdf }}

  ## Include/Ppi/SmmAccess.h
  gPeiSmmAccessPpiGuid          =  { 0x268f33a9, 0xcccd, 0x48be, { 0x88, 0x17, 0x86, 0x5, 0x3a, 0xc3, 0x2e, 0xd6 }}

  ## Include/Ppi/SmmControl.h
  gPeiSmmControlPpiGuid         =  { 0x61c68702, 0x4d7e, 0x4f43, { 0x8d, 0xef, 0xa7, 0x43, 0x5, 0xce, 0x74, 0xc5 }}

  ## Include/Ppi/PostBootScriptTable.h
  gPeiPostScriptTablePpiGuid    =  { 0x88c9d306, 0x900, 0x4eb5, { 0x82, 0x60, 0x3e, 0x2d, 0xbe, 0xda, 0x1f, 0x89}}

  ## Include/Ppi/SerialPortPei.h
  gPeiSerialPortPpiGuid         =  { 0x490e9d85, 0x8aef, 0x4193, { 0x8e, 0x56, 0xf7, 0x34, 0xa9, 0xff, 0xac, 0x8b}}

[Protocols]
  ## Load File protocol provides capability to load and unload EFI image into memory and execute it.
  #  Include/Protocol/LoadPe32Image.h
  #  This protocol is deprecated. Native EDKII module should NOT use this protocol to load/unload image.
  #  If developer need implement such functionality, they should use BasePeCoffLib.
  gEfiLoadPeImageProtocolGuid    = { 0x5CB5C776, 0x60D5, 0x45EE, { 0x88, 0x3C, 0x45, 0x27, 0x08, 0xCD, 0x74, 0x3F }}

  ## Print protocol defines basic print functions to print the format unicode and ascii string.
  # Include/Protocol/Print2.h
  gEfiPrint2ProtocolGuid          = { 0xf05976ef, 0x83f1, 0x4f3d, { 0x86, 0x19, 0xf7, 0x59, 0x5d, 0x41, 0xe5, 0x38 } }

  ## This protocol defines the generic memory test interfaces in Dxe phase.
  # Include/Protocol/GenericMemoryTest.h
  gEfiGenericMemTestProtocolGuid = { 0x309DE7F1, 0x7F5E, 0x4ACE, { 0xB4, 0x9C, 0x53, 0x1B, 0xE5, 0xAA, 0x95, 0xEF }}

  ## Include/Protocol/Dpc.h
  gEfiDpcProtocolGuid            = {0x480f8ae9, 0xc46, 0x4aa9,  { 0xbc, 0x89, 0xdb, 0x9f, 0xba, 0x61, 0x98, 0x6 }}

  ## Fault Tolerant Write protocol provides boot-time service to do fault tolerant write capability for block devices.
  #  Include/Protocol/FaultTolerantWrite.h
  gEfiFaultTolerantWriteProtocolGuid = { 0x3EBD9E82, 0x2C78, 0x4DE6, { 0x97, 0x86, 0x8D, 0x4B, 0xFC, 0xB7, 0xC8, 0x81 }}

  ## This protocol provides boot-time service to do fault tolerant write capability for block devices in SMM environment.
  #  Include/Protocol/SmmFaultTolerantWrite.h
  gEfiSmmFaultTolerantWriteProtocolGuid = { 0x3868fc3b, 0x7e45, 0x43a7, { 0x90, 0x6c, 0x4b, 0xa4, 0x7d, 0xe1, 0x75, 0x4d }}
  
  ## This protocol is used to abstract the swap operation of boot block and backup block of boot FV.
  #  Include/Protocol/SwapAddressRange.h
  gEfiSwapAddressRangeProtocolGuid = { 0x1259F60D, 0xB754, 0x468E, { 0xA7, 0x89, 0x4D, 0xB8, 0x5D, 0x55, 0xE8, 0x7E }}
  
  ## This protocol is used to abstract the swap operation of boot block and backup block of boot FV in SMM environment.
  #  Include/Protocol/SmmSwapAddressRange.h
  gEfiSmmSwapAddressRangeProtocolGuid = { 0x67c4f112, 0x3385, 0x4e55, { 0x9c, 0x5b, 0xc0, 0x5b, 0x71, 0x7c, 0x42, 0x28 }}
  
  ## This protocol is intended for use as a means to store data in the EFI SMM environment.
  #  Include/Protocol/SmmVariableProtocol.h
  gEfiSmmVariableProtocolGuid = { 0xed32d533, 0x99e6, 0x4209, { 0x9c, 0xc0, 0x2d, 0x72, 0xcd, 0xd9, 0x98, 0xa7 }}

  ## This protocol is intended for use as a means to mark a variable read-only after the event EFI_END_OF_DXE_EVENT_GUID is signaled.
  #  Include/Protocol/VariableLock.h
  gEdkiiVariableLockProtocolGuid = { 0xcd3d0a05, 0x9e24, 0x437c, { 0xa8, 0x91, 0x1e, 0xe0, 0x53, 0xdb, 0x76, 0x38 }}

  ## This protocol is similar with DXE FVB protocol and used in the UEFI SMM evvironment.
  #  Include/Protocol/SmmFirmwareVolumeBlock.h
  gEfiSmmFirmwareVolumeBlockProtocolGuid = { 0xd326d041, 0xbd31, 0x4c01, { 0xb5, 0xa8, 0x62, 0x8b, 0xe8, 0x7f, 0x6, 0x53 }}

  ## This protocol allows the error level mask for DEBUG() macros to be adjusted for DXE Phase modules
  # Include/Guid/DebugMask.h  
  gEfiDebugMaskProtocolGuid = { 0x4c8a2451, 0xc207, 0x405b, {0x96, 0x94, 0x99, 0xea, 0x13, 0x25, 0x13, 0x41} }

  ## Include/Protocol/LockBox.h
  gEfiLockBoxProtocolGuid        = { 0xbd445d79, 0xb7ad, 0x4f04, { 0x9a, 0xd8, 0x29, 0xbd, 0x20, 0x40, 0xeb, 0x3c }}
  
  ## Include/Protocol/FormBrowserEx.h
  gEfiFormBrowserExProtocolGuid = { 0x1f73b18d, 0x4630, 0x43c1, { 0xa1, 0xde, 0x6f, 0x80, 0x85, 0x5d, 0x7d, 0xa4 } }

  ## Include/Protocol/EbcVmTest.h
  gEfiEbcVmTestProtocolGuid = { 0xAAEACCFD, 0xF27B, 0x4C17, { 0xB6, 0x10, 0x75, 0xCA, 0x1F, 0x2D, 0xFB, 0x52 } }

  ## Include/Protocol/EbcSimpleDebugger.h
  gEfiEbcSimpleDebuggerProtocolGuid = { 0x2a72d11e, 0x7376, 0x40f6, { 0x9c, 0x68, 0x23, 0xfa, 0x2f, 0xe3, 0x63, 0xf1 } }

  ## Include/Protocol/BootLogo.h
  gEfiBootLogoProtocolGuid = { 0xcdea2bd3, 0xfc25, 0x4c1c, { 0xb9, 0x7c, 0xb3, 0x11, 0x86, 0x6, 0x49, 0x90 } }

  ## Include/Protocol/DisplayProtocol.h
  gEdkiiFormDisplayEngineProtocolGuid = { 0x9bbe29e9, 0xfda1, 0x41ec, { 0xad, 0x52, 0x45, 0x22, 0x13, 0x74, 0x2d, 0x2e } }

  ## Include/Protocol/FormBrowserEx2.h
  gEdkiiFormBrowserEx2ProtocolGuid = { 0xa770c357, 0xb693, 0x4e6d, { 0xa6, 0xcf, 0xd2, 0x1c, 0x72, 0x8e, 0x55, 0xb } }

#
# [Error.gEfiMdeModulePkgTokenSpaceGuid]
#   0x80000001 | Invalid value provided.
#   0x80000002 | Reserved bits must be set to zero.
#   0x80000003 | Incorrect progress code provided.
#   0x80000004 | Invalid foreground color specified.
#   0x80000005 | Invalid background color specified.
#   0x80000006 | Incorrect error code provided.
#

[PcdsFeatureFlag]
  ## Indicates if the platform can support update capsule across a system reset.<BR><BR>
  #   TRUE  - Supports update capsule across a system reset.<BR>
  #   FALSE - Does not support update capsule across a system reset.<BR>
  # @Prompt Enable update capsule across a system reset.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSupportUpdateCapsuleReset|FALSE|BOOLEAN|0x0001001d

  ## Indicates if all PCD PPI services will be enabled.<BR><BR>
  #   TRUE  - All PCD PPI services will be produced.<BR>
  #   FALSE - Minimal PCD PPI services (only GetService) will be produced.<BR>
  # @Prompt Enable full PEI PCD services.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiFullPcdDatabaseEnable|TRUE|BOOLEAN|0x00010020

  ## Indicates if the Device Path To Text Protocol should be produced by the platform.
  #  It can be disabled to save size.<BR><BR>
  #   TRUE  - Device Path To Text Protocol will be produced.<BR>
  #   FALSE - Device Path To Text Protocol will not be produced.<BR>
  # @Prompt Enable Device Path to Text support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDevicePathSupportDevicePathToText|TRUE|BOOLEAN|0x00010037

  ## Indicates if the Device Path From Text Protocol should be produced by the platform.
  #  It can be disabled to save size.<BR><BR>
  #   TRUE  - Device Path From Text Protocol will be produced.<BR>
  #   FALSE - Device Path From Text Protocol will not be produced.<BR>
  # @Prompt Enable Device Path From Text support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDevicePathSupportDevicePathFromText|TRUE|BOOLEAN|0x00010038

  ## Indicates if the statistics about variable usage will be collected. This information is
  #  stored as a vendor configuration table into the EFI system table.
  #  Set this PCD to TRUE to use VariableInfo application in MdeModulePkg\Application directory to get
  #  variable usage info. VariableInfo application will not output information if not set to TRUE.<BR><BR>
  #   TRUE  - Statistics about variable usage will be collected.<BR>
  #   FALSE - Statistics about variable usage will not be collected.<BR>
  # @Prompt Enable variable statistics collection.
  gEfiMdeModulePkgTokenSpaceGuid.PcdVariableCollectStatistics|FALSE|BOOLEAN|0x0001003f

  ## Indicates if Unicode Collation Protocol will be installed.<BR><BR>
  #   TRUE  - Installs Unicode Collation Protocol.<BR>
  #   FALSE - Does not install Unicode Collation Protocol.<BR>
  # @Prompt Enable Unicode Collation support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdUnicodeCollationSupport|TRUE|BOOLEAN|0x00010040

  ## Indicates if Unicode Collation 2 Protocol will be installed.<BR><BR>
  #   TRUE  - Installs Unicode Collation 2 Protocol.<BR>
  #   FALSE - Does not install Unicode Collation 2 Protocol.<BR>
  # @Prompt Enable Unicode Collation 2 support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdUnicodeCollation2Support|TRUE|BOOLEAN|0x00010041

  ## Indicates if Graphics Output Protocol will be installed on virtual handle created by ConsplitterDxe.
  #  It could be set FALSE to save size.<BR><BR>
  #   TRUE  - Installs Graphics Output Protocol on virtual handle created by ConsplitterDxe.<BR>
  #   FALSE - Does not install Graphics Output Protocol on virtual handle created by ConsplitterDxe.<BR>
  # @Prompt Enable ConOut GOP support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdConOutGopSupport|TRUE|BOOLEAN|0x00010042

  ## Indicates if UGA Draw Protocol will be installed on virtual handle created by ConsplitterDxe.
  #  It could be set FALSE to save size.<BR><BR>
  #   TRUE  - Installs UGA Draw Protocol on virtual handle created by ConsplitterDxe.<BR>
  #   FALSE - Does not install UGA Draw Protocol on virtual handle created by ConsplitterDxe.<BR>
  # @Prompt Enable ConOut UGA support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdConOutUgaSupport|TRUE|BOOLEAN|0x00010043

  ## Indicates PeiCore will first search TE section from the PEIM to load the image, or PE32 section, when PeiCore dispatches a PEI module.
  #  This PCD is used to tune PEI phase performance to reduce the search image time.
  #  It can be set according to the generated image section type.<BR><BR>
  #   TRUE  - PeiCore will first search TE section from PEIM to load the image, if TE section is not found, then PeiCore will search PE section.<BR>
  #   FALSE - PeiCore will first search PE section from PEIM to load the image.<BR>
  # @Prompt PeiCore search TE section first.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiCoreImageLoaderSearchTeSectionFirst|TRUE|BOOLEAN|0x00010044

  ## Indicates if to turn off the support of legacy usb. So legacy usb device driver can not make use of SMI
  #  interrupt to access usb device in the case of absence of usb stack.
  #  DUET platform requires the token to be TRUE.<BR><BR>
  #   TRUE  - Turn off usb legacy support.<BR>
  #   FALSE - Does not turn off usb legacy support.<BR>
  # @Prompt Turn off USB legacy support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdTurnOffUsbLegacySupport|FALSE|BOOLEAN|0x00010047
  
  ## Indicates if HiiImageProtocol will be installed.
  #  FALSE is for size reduction.<BR><BR>
  #   TRUE  - Installs HiiImageProtocol.<BR>
  #   FALSE - Does not install HiiImageProtocol.<BR>
  # @Prompt Enable HII image support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSupportHiiImageProtocol|TRUE|BOOLEAN|0x00010100

  ## Indicates if USB KeyBoard Driver disables the default keyboard layout.
  #  The default keyboard layout serves as the backup when no keyboard layout can be retrieved
  #  from HII database.<BR><BR>
  #   TRUE  - USB KeyBoard Driver will disable the default keyboard layout.<BR>
  #   FALSE - USB KeyBoard Driver will not disable the default keyboard layout.<BR>
  # @Prompt Disable default keyboard layout in USB KeyBoard Driver.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDisableDefaultKeyboardLayoutInUsbKbDriver|FALSE|BOOLEAN|0x00010200

  ## Indicates if backward compatibility to Framework HII and Framework FvHob is supported.<BR><BR>
  #   TRUE  - Setup Browser supports GUID opcodes generated from Framework HII VFR file by VFR compiler.
  #           the PeiCore will handle the framework FvHob and install FvInfo PPI for it.<BR>
  #   FALSE - Setup Browser doesn't support GUID opcodes generated from Framework HII VFR file by VFR compiler.
  #           the PeiCore will not handle the framework FvHob and install FvInfo PPI for it.<BR>
  # @Prompt Enable framework backward compatibility support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFrameworkCompatibilitySupport|FALSE|BOOLEAN|0x00012009

  ## Indicates if HelloWorld Application will print the verbose information.
  #  This PCD is a sample to explain FeatureFlag PCD usage.<BR><BR>
  #   TRUE  - HelloWorld Application will print the verbose information.<BR>
  #   FALSE - HelloWorld Application will not print the verbose information.<BR>
  # @Prompt Enable HelloWorld print.
  gEfiMdeModulePkgTokenSpaceGuid.PcdHelloWorldPrintEnable|TRUE|BOOLEAN|0x0001200a

  ## Indicates if FULL FTW protocol services (total six APIs) will be produced.<BR><BR>
  #   TRUE  - Produces FULL FTW protocol services (total six APIs).<BR>
  #   FALSE - Only FTW Write service is available.<BR>
  # @Prompt Enable FULL FTW services.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFullFtwServiceEnable|TRUE|BOOLEAN|0x0001200b

  ## Indicates if DXE IPL supports the UEFI decompression algorithm.<BR><BR>
  #   TRUE  - DXE IPL will support UEFI decompression.<BR>
  #   FALSE - DXE IPL will not support UEFI decompression to save space.<BR>
  # @Prompt Enable UEFI decompression support in DXE IPL.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDxeIplSupportUefiDecompress|TRUE|BOOLEAN|0x0001200c

  ## Indicates if PciBus driver supports the hot plug device.<BR><BR>
  #   TRUE  - PciBus driver supports the hot plug device.<BR>
  #   FALSE - PciBus driver doesn't support the hot plug device.<BR>
  # @Prompt Enable PciBus hot plug device support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPciBusHotplugDeviceSupport|TRUE|BOOLEAN|0x0001003d

  ## Indicates if the PciBus driver probes non-standard, such as 2K/1K/512, granularity for PCI to PCI bridge I/O window.<BR><BR>
  #   TRUE  - PciBus driver probes non-standard granularity for PCI to PCI bridge I/O window.<BR>
  #   FALSE - PciBus driver doesn't probe non-standard granularity for PCI to PCI bridge I/O window.<BR>
  # @Prompt Enable PCI bridge IO alignment probe.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPciBridgeIoAlignmentProbe|FALSE|BOOLEAN|0x0001004e

  ## Indicates if StatusCode is reported via Serial port.<BR><BR>
  #   TRUE  - Reports StatusCode via Serial port.<BR>
  #   FALSE - Does not report StatusCode via Serial port.<BR>
  # @Prompt Enable StatusCode via Serial port.
  gEfiMdeModulePkgTokenSpaceGuid.PcdStatusCodeUseSerial|TRUE|BOOLEAN|0x00010022

  ## Indicates if StatusCode is stored in memory.
  #  The memory is boot time memory in PEI Phase and is runtime memory in DXE Phase.<BR><BR>
  #   TRUE  - Stores StatusCode in memory.<BR>
  #   FALSE - Does not store StatusCode in memory.<BR>
  # @Prompt Enable StatusCode via memory.
  gEfiMdeModulePkgTokenSpaceGuid.PcdStatusCodeUseMemory|FALSE|BOOLEAN|0x00010023

  ## Indicates if PEI phase StatusCode will be replayed in DXE phase.<BR><BR>
  #   TRUE  - Replays PEI phase StatusCode in DXE phased.<BR>
  #   FALSE - Does not replay PEI phase StatusCode in DXE phase.<BR>
  # @Prompt Enable PEI StatusCode replay in DXE phase
  gEfiMdeModulePkgTokenSpaceGuid.PcdStatusCodeReplayIn|FALSE|BOOLEAN|0x0001002d

  ## Indicates if ACPI SDT protocol will be installed.<BR><BR>
  #   TRUE  - Installs ACPI SDT protocol.<BR>
  #   FALSE - Does not install ACPI SDT protocol.<BR>
  # @Prompt Enable ACPI SDT support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdInstallAcpiSdtProtocol|FALSE|BOOLEAN|0x0001004d

  ## Indicates if the unaligned I/O, MMIO, and PCI Configuration cycles through the PCI I/O Protocol are enabled.
  #  The default value for this PCD is false to disable support for unaligned PCI I/O Protocol requests.<BR><BR>
  #   TRUE  - Enables the unaligned I/O, MMIO, and PCI Configuration cycles through the PCI I/O Protocol.<BR>
  #   FALSE - Disables the unaligned I/O, MMIO, and PCI Configuration cycles through the PCI I/O Protocol.<BR>
  # @Prompt Enable unaligned PCI I/O support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdUnalignedPciIoEnable|FALSE|BOOLEAN|0x0001003e

  ## Indicates if TEXT statement is always set to GrayOut statement in HII Form Browser.<BR><BR>
  #   TRUE  - TEXT statement will always be set to GrayOut.<BR>
  #   FALSE - TEXT statement will be set to GrayOut only when GrayOut condition is TRUE.<BR>
  # @Prompt Always GrayOut TEXT statement.
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowserGrayOutTextStatement|FALSE|BOOLEAN|0x0001004f

  ## Indicates if unselectable menu should be gray out in HII Form Browser.<BR><BR>
  #   TRUE  - The unselectable menu will be set to GrayOut.<BR>
  #   FALSE - The menu will be show as normal menu entry even if it is not selectable.<BR>
  # @Prompt GrayOut read only menu.
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowerGrayOutReadOnlyMenu|FALSE|BOOLEAN|0x00010070

  ## Indicates if recovery from IDE disk will be supported.<BR><BR>
  #   TRUE  - Supports recovery from IDE disk.<BR>
  #   FALSE - Does not support recovery from IDE disk.<BR>
  # @Prompt Enable recovery on IDE disk.
  gEfiMdeModulePkgTokenSpaceGuid.PcdRecoveryOnIdeDisk|TRUE|BOOLEAN|0x00010060

  ## Indicates if recovery from FAT floppy disk will be supported.<BR><BR>
  #   TRUE  - Supports recovery from FAT floppy disk.<BR>
  #   FALSE - Does not support recovery from FAT floppy disk.<BR>
  # @Prompt Enable recovery on FAT floppy disk.
  gEfiMdeModulePkgTokenSpaceGuid.PcdRecoveryOnFatFloppyDisk|TRUE|BOOLEAN|0x00010061

  ## Indicates if recovery from data CD will be supported.<BR><BR>
  #   TRUE  - Supports recovery from data CD.<BR>
  #   FALSE - Does not support recovery from data CD.<BR>
  # @Prompt Enable recovery on data CD.
  gEfiMdeModulePkgTokenSpaceGuid.PcdRecoveryOnDataCD|TRUE|BOOLEAN|0x00010062

  ## Indicates if recovery from FAT USB disk will be supported.<BR><BR>
  #   TRUE  - Supports recovery from USB disk.<BR>
  #   FALSE - Does not support recovery from USB disk.<BR>
  # @Prompt Enable recovery on FAT USB disk.
  gEfiMdeModulePkgTokenSpaceGuid.PcdRecoveryOnFatUsbDisk|TRUE|BOOLEAN|0x00010063

  ## Indicates if S3 performance data will be supported in ACPI FPDT table.<BR><BR>
  #   TRUE  - S3 performance data will be supported in ACPI FPDT table.<BR>
  #   FALSE - S3 performance data will not be supported in ACPI FPDT table.<BR>
  # @Prompt Enable S3 performance data support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFirmwarePerformanceDataTableS3Support|TRUE|BOOLEAN|0x00010064

[PcdsFeatureFlag.IA32, PcdsFeatureFlag.X64]
  ## Indicates if DxeIpl should switch to long mode to enter DXE phase.
  #  It is assumed that 64-bit DxeCore is built in firmware if it is true; otherwise 32-bit DxeCore
  #  is built in firmware.<BR><BR>
  #   TRUE  - DxeIpl will load a 64-bit DxeCore and switch to long mode to hand over to DxeCore.<BR>
  #   FALSE - DxeIpl will load a 32-bit DxeCore and perform stack switch to hand over to DxeCore.<BR>
  # @Prompt DxeIpl switch to long mode.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDxeIplSwitchToLongMode|TRUE|BOOLEAN|0x0001003b

  ## Indicates if DxeIpl should rebuild page tables. This flag only
  #  makes sense in the case where the DxeIpl and the DxeCore are both X64.<BR><BR>
  #   TRUE  - DxeIpl will rebuild page tables.<BR>
  #   FALSE - DxeIpl will not rebuild page tables.<BR>
  # @Prompt DxeIpl rebuild page tables.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDxeIplBuildPageTables|TRUE|BOOLEAN|0x0001003c

[PcdsFixedAtBuild]
  ## Flag of enabling/disabling the feature of Loading Module at Fixed Address.<BR><BR>
  #  0xFFFFFFFFFFFFFFFF: Enable the feature as fixed offset to TOLM.<BR>
  #  0:                  Disable the feature.<BR>
  #  Other Value:        Enable the feature as fixed absolute address, and the value is the top memory address.<BR>
  # @Prompt Enable LMFA feature.
  # @Expression 0x80000001 | (gEfiMdeModulePkgTokenSpaceGuid.PcdLoadModuleAtFixAddressEnable == 0xFFFFFFFFFFFFFFFF || gEfiMdeModulePkgTokenSpaceGuid.PcdLoadModuleAtFixAddressEnable <= 0x0FFFFFFFFFFFFFFF)
  gEfiMdeModulePkgTokenSpaceGuid.PcdLoadModuleAtFixAddressEnable|0|UINT64|0x30001015

  ## Progress Code for OS Loader LoadImage start.<BR><BR>
  #  PROGRESS_CODE_OS_LOADER_LOAD   = (EFI_SOFTWARE_DXE_BS_DRIVER | (EFI_OEM_SPECIFIC | 0x00000000)) = 0x03058000<BR>
  # @Prompt Progress Code for OS Loader LoadImage start.
  # @ValidList  0x80000003 | 0x03058000
  gEfiMdeModulePkgTokenSpaceGuid.PcdProgressCodeOsLoaderLoad|0x03058000|UINT32|0x30001030

  ## Progress Code for OS Loader StartImage start.<BR><BR>
  #  PROGRESS_CODE_OS_LOADER_START  = (EFI_SOFTWARE_DXE_BS_DRIVER | (EFI_OEM_SPECIFIC | 0x00000001)) = 0x03058001<BR>
  # @Prompt Progress Code for OS Loader StartImage start.
  # @ValidList  0x80000003 | 0x03058001
  gEfiMdeModulePkgTokenSpaceGuid.PcdProgressCodeOsLoaderStart|0x03058001|UINT32|0x30001031

  ## Progress Code for S3 Suspend start.<BR><BR>
  #  PROGRESS_CODE_S3_SUSPEND_START = (EFI_SOFTWARE_SMM_DRIVER | (EFI_OEM_SPECIFIC | 0x00000000))    = 0x03078000<BR>
  # @Prompt Progress Code for S3 Suspend start.
  # @ValidList  0x80000003 | 0x03078000
  gEfiMdeModulePkgTokenSpaceGuid.PcdProgressCodeS3SuspendStart|0x03078000|UINT32|0x30001032

  ## Progress Code for S3 Suspend end.<BR><BR>
  #  PROGRESS_CODE_S3_SUSPEND_END   = (EFI_SOFTWARE_SMM_DRIVER | (EFI_OEM_SPECIFIC | 0x00000001))    = 0x03078001<BR>
  # @Prompt Progress Code for S3 Suspend end.
  # @ValidList  0x80000003 | 0x03078001
  gEfiMdeModulePkgTokenSpaceGuid.PcdProgressCodeS3SuspendEnd|0x03078001|UINT32|0x30001033

  ## Error Code for SetVariable failure.<BR><BR>
  #  EDKII_ERROR_CODE_SET_VARIABLE  = (EFI_SOFTWARE_DXE_BS_DRIVER | (EFI_OEM_SPECIFIC | 0x00000002)) = 0x03058002<BR>
  # @Prompt Error Code for SetVariable failure.
  # @ValidList  0x80000006 | 0x03058002
  gEfiMdeModulePkgTokenSpaceGuid.PcdErrorCodeSetVariable|0x03058002|UINT32|0x30001040

[PcdsFixedAtBuild, PcdsPatchableInModule]
  ## Dynamic type PCD can be registered callback function for Pcd setting action.
  #  PcdMaxPeiPcdCallBackNumberPerPcdEntry indicates the maximum number of callback function
  #  for a dynamic PCD used in PEI phase.
  # @Prompt Max PEI PCD callback number per PCD entry.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxPeiPcdCallBackNumberPerPcdEntry|0x08|UINT32|0x0001000f

  ## VPD type PCD  allows a developer to point to an absolute physical address PcdVpdBaseAddress
  #  to store PCD value.
  # @Prompt VPD base address.
  gEfiMdeModulePkgTokenSpaceGuid.PcdVpdBaseAddress|0x0|UINT32|0x00010010

  ## Maximum number of FV is supported by PeiCore's dispatching.
  # @Prompt Maximum number of FV supported by PeiCore.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiCoreMaxFvSupported|6|UINT32|0x00010030

  ## Maximum File count in every FV is supported by PeiCore's dispatching.
  #  PeiCore supported File type includes PEIM, Combined PEIM and FV.
  # @Prompt Maximum File count per FV supported by PeiCore.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiCoreMaxPeimPerFv|32|UINT32|0x00010031

  ## Maximum stack size for PeiCore.
  # @Prompt Maximum stack size for PeiCore.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiCoreMaxPeiStackSize|0x20000|UINT32|0x00010032

  ## Maximum PPI count is supported by PeiCore's PPI database.
  # @Prompt Maximum PPI count supported by PeiCore.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPeiCoreMaxPpiSupported|64|UINT32|0x00010033

  ## The maximum size of a single non-HwErr type variable.
  # @Prompt Maximum variable size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxVariableSize|0x400|UINT32|0x30000003

  ## The maximum size of single hardware error record variable.<BR><BR>
  # In IA32/X64 platforms, this value should be larger than 1KB.<BR>
  # In IA64 platforms, this value should be larger than 128KB.<BR>
  # @Prompt Maximum HwErr variable size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxHardwareErrorVariableSize|0x8000|UINT32|0x30000004

  ## The size of reserved HwErr variable space. Note that this value must be less than or equal to PcdFlashNvStorageVariableSize.
  # In EdkII implementation, HwErr type variable is stored with common non-volatile variables in the same NV region.
  # so the platform integrator should ensure this value is less than or equal to PcdFlashNvStorageVariableSize.
  # this value is used to guarantee the space of HwErr type variable and not populated by common variable.
  # @Prompt HwErr variable storage size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdHwErrStorageSize|0x0000|UINT32|0x30000006

  ## The size of volatile buffer. This buffer is used to store VOLATILE attribute variables.
  # @Prompt Variable storage size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdVariableStoreSize|0x10000|UINT32|0x30000005

  ## FFS filename to find the ACPI tables.
  # @Prompt FFS name of ACPI tables storage.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiTableStorageFile|{ 0x25, 0x4e, 0x37, 0x7e, 0x01, 0x8e, 0xee, 0x4f, 0x87, 0xf2, 0x39, 0xc, 0x23, 0xc6, 0x6, 0xcd }|VOID*|0x30000016

  ## FFS filename to find the capsule coalesce image.
  # @Prompt FFS name of capsule coalesce image.
  gEfiMdeModulePkgTokenSpaceGuid.PcdCapsuleCoalesceFile|{ 0xA6, 0xE4, 0xFD, 0xF7, 0x4C, 0x29, 0x3c, 0x49, 0xB5, 0x0F, 0x97, 0x34, 0x55, 0x3B, 0xB7, 0x57 }|VOID*|0x30000017

  ## Maximum number of performance log entries during PEI phase.
  # @Prompt Maximum number of PEI performance log entries.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxPeiPerformanceLogEntries|40|UINT8|0x0001002f

  ## RTC Update Timeout Value(microsecond).
  # @Prompt RTC Update Timeout Value.
  gEfiMdeModulePkgTokenSpaceGuid.PcdRealTimeClockUpdateTimeout|100000|UINT32|0x00010034

  ## Indicates the 16550 serial port registers are in MMIO space, or in I/O space. Default is I/O space.<BR><BR>
  #   TRUE  - 16550 serial port registers are in MMIO space.<BR>
  #   FALSE - 16550 serial port registers are in I/O space.<BR>
  # @Prompt Serial port registers use MMIO.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseMmio|FALSE|BOOLEAN|0x00020000

  ## Indicates if the 16550 serial port hardware flow control will be enabled. Default is FALSE.<BR><BR>
  #   TRUE  - 16550 serial port hardware flow control will be enabled.<BR>
  #   FALSE - 16550 serial port hardware flow control will be disabled.<BR>
  # @Prompt Enable serial port hardware flow control.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseHardwareFlowControl|FALSE|BOOLEAN|0x00020001

  ## Indicates if the 16550 serial Tx operations will be blocked if DSR is not asserted (no cable). Default is FALSE.
  #  This PCD is ignored if PcdSerialUseHardwareFlowControl is FALSE.<BR><BR>
  #   TRUE  - 16550 serial Tx operations will be blocked if DSR is not asserted.<BR>
  #   FALSE - 16550 serial Tx operations will not be blocked if DSR is not asserted.<BR>
  # @Prompt Enable serial port cable detetion.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialDetectCable|FALSE|BOOLEAN|0x00020006
    
  ## Base address of 16550 serial port registers in MMIO or I/O space. Default is 0x3F8.
  # @Prompt Base address of serial port registers.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterBase|0x03F8|UINT64|0x00020002

  ## Baud rate for the 16550 serial port.  Default is 115200 baud.
  # @Prompt Baud rate for serial port.
  # @ValidList  0x80000001 | 921600, 460800, 230400, 115200, 57600, 38400, 19200, 9600, 7200, 4800, 3600, 2400, 2000, 1800, 1200, 600, 300, 150, 134, 110, 75, 50
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialBaudRate|115200|UINT32|0x00020003

  ## Line Control Register (LCR) for the 16550 serial port. This encodes data bits, parity, and stop bits.<BR><BR>
  #    BIT1..BIT0 - Data bits.  00b = 5 bits, 01b = 6 bits, 10b = 7 bits, 11b = 8 bits<BR>
  #    BIT2       - Stop Bits.  0 = 1 stop bit.  1 = 1.5 stop bits if 5 data bits selected, otherwise 2 stop bits.<BR>
  #    BIT5..BIT3 - Parity.  xx0b = No Parity, 001b = Odd Parity, 011b = Even Parity, 101b = Mark Parity, 111b=Stick Parity<BR>
  #    BIT7..BIT6 - Reserved.  Must be 0.<BR>
  #
  #  Default is No Parity, 8 Data Bits, 1 Stop Bit.<BR>
  # @Prompt Serial port Line Control settings.
  # @Expression 0x80000002 | (gEfiMdeModulePkgTokenSpaceGuid.PcdSerialLineControl & 0xC0) == 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialLineControl|0x03|UINT8|0x00020004

  ## FIFO Control Register (FCR) for the 16550 serial port.<BR><BR>
  #    BIT0       - FIFO Enable.  0 = Disable FIFOs.  1 = Enable FIFOs.<BR>
  #    BIT1       - Clear receive FIFO.  1 = Clear FIFO.<BR>
  #    BIT2       - Clear transmit FIFO.  1 = Clear FIFO.<BR>
  #    BIT4..BIT3 - Reserved.  Must be 0.<BR>
  #    BIT5       - Enable 64-byte FIFO.  0 = Disable 64-byte FIFO.  1 = Enable 64-byte FIFO<BR>
  #    BIT7..BIT6 - Reserved.  Must be 0.<BR>
  #
  #  Default is to enable and clear all FIFOs.<BR>
  # @Prompt Serial port FIFO Control settings.
  # @Expression 0x80000002 | (gEfiMdeModulePkgTokenSpaceGuid.PcdSerialFifoControl & 0xD8) == 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialFifoControl|0x07|UINT8|0x00020005

  ## TFTP BlockSize. Initial value 0 means using default block size which is (MTU-IP_HEADER-UDP_HEADER-TFTP_HEADER)
  #  to handle all link layers. If the value is non zero, the PCD value will be used as block size.
  # @Prompt TFTP block size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdTftpBlockSize|0x0|UINT64|0x30001026

  ## Maximum address that the DXE Core will allocate the EFI_SYSTEM_TABLE_POINTER
  #  structure. The default value for this PCD is 0, which means that the DXE Core
  #  will allocate the buffer from the EFI_SYSTEM_TABLE_POINTER structure on a 4MB
  #  boundary as close to the top of memory as feasible.  If this PCD is set to a 
  #  value other than 0, then the DXE Core will first attempt to allocate the
  #  EFI_SYSTEM_TABLE_POINTER structure on a 4MB boundary below the address specified
  #  by this PCD, and if that allocation fails, retry the allocation on a 4MB
  #  boundary as close to the top of memory as feasible.
  # @Prompt Maximum Efi System Table Pointer address.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxEfiSystemTablePointerAddress|0x0|UINT64|0x30001027

  ## Indicates if to shadow PEIM on S3 boot path after memory is ready.<BR><BR>
  #   TRUE  - Shadow PEIM on S3 boot path after memory is ready.<BR>
  #   FALSE - Not shadow PEIM on S3 boot path after memory is ready.<BR>
  # @Prompt Shadow Peim On S3 Boot. 
  gEfiMdeModulePkgTokenSpaceGuid.PcdShadowPeimOnS3Boot|FALSE|BOOLEAN|0x30001028

  ## Default OEM ID for ACPI table creation, its length must be 0x6 bytes to follow ACPI specification.
  # @Prompt Default OEM ID for ACPI table creation.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemId|"INTEL "|VOID*|0x30001034

  ## Default OEM Table ID for ACPI table creation, it is "EDK2    ".
  # @Prompt Default OEM Table ID for ACPI table creation.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemTableId|0x20202020324B4445|UINT64|0x30001035

  ## Default OEM Revision for ACPI table creation.
  # @Prompt Default OEM Revision for ACPI table creation.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemRevision|0x00000002|UINT32|0x30001036

  ## Default Creator ID for ACPI table creation.
  # @Prompt Default Creator ID for ACPI table creation.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultCreatorId|0x20202020|UINT32|0x30001037

  ## Default Creator Revision for ACPI table creation.
  # @Prompt Default Creator Revision for ACPI table creation.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultCreatorRevision|0x01000013|UINT32|0x30001038

  ## UART clock frequency is for the baud rate configuration.
  # @Prompt Serial Port Clock Rate.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialClockRate|1843200|UINT32|0x00010066
  
  ## PCI Serial Device Info. It is an array of Device, Function, and Power Management
  #  information that describes the path that contains zero or more PCI to PCI briges 
  #  followed by a PCI serial device.  Each array entry is 4-bytes in length.  The 
  #  first byte is the PCI Device Number, then second byte is the PCI Function Number, 
  #  and the last two bytes are the offset to the PCI power management capabilities 
  #  register used to manage the D0-D3 states.  If a PCI power management capabilities 
  #  register is not present, then the last two bytes in the offset is set to 0.  The 
  #  array is terminated by an array entry with a PCI Device Number of 0xFF.  For a 
  #  non-PCI fixed address serial device, such as an ISA serial device, the value is 0xFF.
  # @Prompt Pci Serial Device Info
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialPciDeviceInfo|{0xFF}|VOID*|0x00010067

  ## Serial Port Extended Transmit FIFO Size.  The default is 64 bytes. 
  # @Prompt Serial Port Extended Transmit FIFO Size in Bytes
  gEfiMdeModulePkgTokenSpaceGuid.PcdSerialExtendedTxFifoSize|64|UINT32|0x00010068
  
[PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx]
  ## This PCD defines the Console output row. The default value is 25 according to UEFI spec.
  #  This PCD could be set to 0 then console output would be at max column and max row.
  # @Prompt Console output row.
  gEfiMdeModulePkgTokenSpaceGuid.PcdConOutRow|25|UINT32|0x40000006

  ## This PCD defines the Console output row. The default value is 80 according to UEFI spec.
  #  This PCD could be set to 0 then console output would be at max column and max row.
  # @Prompt Console output column.
  gEfiMdeModulePkgTokenSpaceGuid.PcdConOutColumn|80|UINT32|0x40000007

  ## This PCD defines the video horizontal resolution.
  #  If this PCD is set to 0 then video resolution would be at highest resolution.
  # @Prompt Video horizontal resolution.
  gEfiMdeModulePkgTokenSpaceGuid.PcdVideoHorizontalResolution|800|UINT32|0x40000009

  ## This PCD defines the video vertical resolution.
  #  If this PCD is set to 0 then video resolution would be at highest resolution.
  # @Prompt Video vertical resolution.
  gEfiMdeModulePkgTokenSpaceGuid.PcdVideoVerticalResolution|600|UINT32|0x4000000a

[PcdsFixedAtBuild, PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx]
  ## Base address of the NV variable range in flash device.
  # @Prompt Base address of flash NV variable range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageVariableBase|0x0|UINT32|0x30000001

  ## Size of the NV variable range. Note that this value should less than or equal to PcdFlashNvStorageFtwSpareSize.
  #  The root cause is that variable driver will use FTW protocol to reclaim variable region.
  #  If the length of variable region is larger than FTW spare size, it means the whole variable region can not
  #  be reflushed through the manner of fault tolerant write.
  # @Prompt Size of flash NV variable range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageVariableSize|0x0|UINT32|0x30000002

  ## Base address of the FTW spare block range in flash device. Note that this value should be block size aligned.
  # @Prompt Base address of flash FTW spare block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwSpareBase|0x0|UINT32|0x30000013

  ## Size of the FTW spare block range. Note that this value should larger than PcdFlashNvStorageVariableSize and block size aligned.
  # The root cause is that variable driver will use FTW protocol to reclaim variable region.
  # If the length of variable region is larger than FTW spare size, it means the whole variable region can not
  # be reflushed through the manner of fault tolerant write.
  # @Prompt Size of flash FTW spare block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwSpareSize|0x0|UINT32|0x30000014

  ## Base address of the FTW working block range in flash device.
  # If PcdFlashNvStorageFtwWorkingSize is larger than one block size, this value should be block size aligned.
  # @Prompt Base address of flash FTW working block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwWorkingBase|0x0|UINT32|0x30000010

  ## Size of the FTW working block range.
  # If the value is less than one block size, the work space range should not span blocks.
  # If the value is larger than one block size, it should be block size aligned.
  # @Prompt Size of flash FTW working block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwWorkingSize|0x0|UINT32|0x30000011

  ## 64-bit Base address of the NV variable range in flash device.
  # @Prompt 64-bit Base address of flash NV variable range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageVariableBase64|0x0|UINT64|0x80000001

  ## 64-bit Base address of the FTW spare block range in flash device. Note that this value should be block size aligned.
  # @Prompt 64-bit Base address of flash FTW spare block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwSpareBase64|0x0|UINT64|0x80000013

  ## 64-bit Base address of the FTW working block range in flash device.
  # If PcdFlashNvStorageFtwWorkingSize is larger than one block size, this value should be block size aligned.
  # @Prompt 64-bit Base address of flash FTW working block range.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwWorkingBase64|0x0|UINT64|0x80000010

  ## This PCD defines a reserved memory range for the EMU Variable driver's NV Variable Store.
  #  The range is valid if non-zero. The memory range size must be PcdVariableStoreSize.
  # @Prompt Reserved memory range for EMU variable NV storage.
  gEfiMdeModulePkgTokenSpaceGuid.PcdEmuVariableNvStoreReserved|0|UINT64|0x40000008

  ## This PCD defines the times to print hello world string.
  #  This PCD is a sample to explain UINT32 PCD usage.
  # @Prompt HellowWorld print times.
  gEfiMdeModulePkgTokenSpaceGuid.PcdHelloWorldPrintTimes|1|UINT32|0x40000005

  ## This PCD defines the HelloWorld print string.
  #  This PCD is a sample to explain String typed PCD usage.
  # @Prompt HelloWorld print string.
  gEfiMdeModulePkgTokenSpaceGuid.PcdHelloWorldPrintString|L"UEFI Hello World!\n"|VOID*|0x40000004

  ## Indicates the maximum size of the capsule image with a reset flag that the platform can support.
  #  The default max size is 100MB (0x6400000) for more than one large capsule images.
  # @Prompt Max size of populated capsule.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxSizePopulateCapsule|0x6400000|UINT32|0x0001001e

  ## Indicates the maximum size of the capsule image without a reset flag that the platform can support.
  #  The default max size is 10MB (0xa00000) for the casule image without reset flag setting.
  # @Prompt Max size of non-populated capsule.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMaxSizeNonPopulateCapsule|0xa00000|UINT32|0x0001001f

  ## Null-terminated Unicode string of the firmware vendor name that is the default name filled into the EFI System Table.
  # @Prompt Firmware vendor.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFirmwareVendor|L"EDK II"|VOID*|0x00010050

  ## Firmware revision that is the default revision filled into the EFI System Table.
  # @Prompt Firmware revision.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFirmwareRevision|0x00010000|UINT32|0x00010051

  ## Null-terminated Unicode string that describes the firmware version.
  # @Prompt Firmware version string.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFirmwareVersionString|L""|VOID*|0x00010052

  ## Null-terminated Unicode string that contains the date the firmware was released
  # @Prompt Firmware release data string.
  gEfiMdeModulePkgTokenSpaceGuid.PcdFirmwareReleaseDateString|L""|VOID*|0x00010053

  ## PcdStatusCodeMemorySize is used when PcdStatusCodeUseMemory is set to true.
  #  (PcdStatusCodeMemorySize * KBytes) is the total taken memory size.<BR><BR>
  #  The default value in PeiPhase is 1 KBytes.<BR>
  #  The default value in DxePhase is 128 KBytes.<BR>
  # @Prompt StatusCode memory size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdStatusCodeMemorySize|1|UINT16|0x00010054

  ## Indicates if to reset system when memory type information changes.<BR><BR>
  #   TRUE  - Resets system when memory type information changes.<BR>
  #   FALSE - Does not reset system when memory type information changes.<BR>
  # @Prompt Reset on memory type information change.
  gEfiMdeModulePkgTokenSpaceGuid.PcdResetOnMemoryTypeInformationChange|TRUE|BOOLEAN|0x00010056

  ## Specify the foreground color for Subtile text in HII Form Browser. The default value is EFI_BLUE.
  #  Only following values defined in UEFI specification are valid:<BR><BR>
  #  0x00 (EFI_BLACK)<BR>
  #  0x01 (EFI_BLUE)<BR>
  #  0x02 (EFI_GREEN)<BR>
  #  0x03 (EFI_CYAN)<BR>
  #  0x04 (EFI_RED)<BR>
  #  0x05 (EFI_MAGENTA)<BR>
  #  0x06 (EFI_BROWN)<BR>
  #  0x07 (EFI_LIGHTGRAY)<BR>
  #  0x08 (EFI_DARKGRAY)<BR>
  #  0x09 (EFI_LIGHTBLUE)<BR>
  #  0x0A (EFI_LIGHTGREEN)<BR>
  #  0x0B (EFI_LIGHTCYAN)<BR>
  #  0x0C (EFI_LIGHTRED)<BR>
  #  0x0D (EFI_LIGHTMAGENTA)<BR>
  #  0x0E (EFI_YELLOW)<BR>
  #  0x0F (EFI_WHITE)<BR>
  # @Prompt Foreground color for browser subtile.
  # @ValidRange 0x80000004 | 0x00 - 0x0F
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowserSubtitleTextColor|0x01|UINT8|0x00010057
  
  ## Specify the foreground color for prompt and Question value text in HII Form Browser. The default value is EFI_BLACK.
  #  Only following values defined in UEFI specification are valid:<BR><BR>
  #  0x00 (EFI_BLACK)<BR>
  #  0x01 (EFI_BLUE)<BR>
  #  0x02 (EFI_GREEN)<BR>
  #  0x03 (EFI_CYAN)<BR>
  #  0x04 (EFI_RED)<BR>
  #  0x05 (EFI_MAGENTA)<BR>
  #  0x06 (EFI_BROWN)<BR>
  #  0x07 (EFI_LIGHTGRAY)<BR>
  #  0x08 (EFI_DARKGRAY)<BR>
  #  0x09 (EFI_LIGHTBLUE)<BR>
  #  0x0A (EFI_LIGHTGREEN)<BR>
  #  0x0B (EFI_LIGHTCYAN)<BR>
  #  0x0C (EFI_LIGHTRED)<BR>
  #  0x0D (EFI_LIGHTMAGENTA)<BR>
  #  0x0E (EFI_YELLOW)<BR>
  #  0x0F (EFI_WHITE)<BR>
  # @Prompt Foreground color for browser field.
  # @ValidRange 0x80000004 | 0x00 - 0x0F
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowserFieldTextColor|0x00|UINT8|0x00010058
  
  ## Specify the foreground color for highlighted prompt and Question value text in HII Form Browser.
  #  The default value is EFI_LIGHTGRAY. Only following values defined in UEFI specification are valid:<BR><BR>
  #  0x00 (EFI_BLACK)<BR>
  #  0x01 (EFI_BLUE)<BR>
  #  0x02 (EFI_GREEN)<BR>
  #  0x03 (EFI_CYAN)<BR>
  #  0x04 (EFI_RED)<BR>
  #  0x05 (EFI_MAGENTA)<BR>
  #  0x06 (EFI_BROWN)<BR>
  #  0x07 (EFI_LIGHTGRAY)<BR>
  #  0x08 (EFI_DARKGRAY)<BR>
  #  0x09 (EFI_LIGHTBLUE)<BR>
  #  0x0A (EFI_LIGHTGREEN)<BR>
  #  0x0B (EFI_LIGHTCYAN)<BR>
  #  0x0C (EFI_LIGHTRED)<BR>
  #  0x0D (EFI_LIGHTMAGENTA)<BR>
  #  0x0E (EFI_YELLOW)<BR>
  #  0x0F (EFI_WHITE)<BR>
  # @Prompt Foreground color for highlighted browser field.
  # @ValidRange 0x80000004 | 0x00 - 0x0F
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowserFieldTextHighlightColor|0x07|UINT8|0x00010059
  
  ## Specify the background color for highlighted prompt and Question value text in HII Form Browser.
  #  The default value is EFI_BACKGROUND_BLACK. Only following values defined in UEFI specification are valid:<BR><BR>
  #  0x00 (EFI_BACKGROUND_BLACK)<BR>
  #  0x10 (EFI_BACKGROUND_BLUE)<BR>
  #  0x20 (EFI_BACKGROUND_GREEN)<BR>
  #  0x30 (EFI_BACKGROUND_CYAN)<BR>
  #  0x40 (EFI_BACKGROUND_RED)<BR>
  #  0x50 (EFI_BACKGROUND_MAGENTA)<BR>
  #  0x60 (EFI_BACKGROUND_BROWN)<BR>
  #  0x70 (EFI_BACKGROUND_LIGHTGRAY)<BR>
  # @Prompt Background color for highlighted browser field.
  # @ValidList  0x80000005 | 0x00, 0x10, 0x20, 0x30, 0x40, 0x50, 0x60, 0x70
  gEfiMdeModulePkgTokenSpaceGuid.PcdBrowserFieldBackgroundHighlightColor|0x00|UINT8|0x0001005A

  ## Time in second to delay for SATA devices to spin-up for recovery.
  # @Prompt SATA spin-up delay time in second for recovery path.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSataSpinUpDelayInSecForRecoveryPath|15|UINT16|0x0001005B

  ## This PCD is used to specify memory size with page number for a pre-allocated ACPI NVS memory to hold
  #  runtime created S3 boot script entries. The default page number is 2. When changing the value of this
  #  PCD, the platform developer should make sure the memory size is large enough to hold the S3 boot
  #  script node created in runtime phase.
  # @Prompt Reserved page number for S3 Boot Script Runtime Table.
  gEfiMdeModulePkgTokenSpaceGuid.PcdS3BootScriptRuntimeTableReservePageNumber|0x2|UINT16|0x0001005C

  ## The PCD is used to specify the stack size when capsule IA32 PEI transfers to long mode in PEI phase.
  #  The default size is 32K. When changing the value of this PCD, the platform developer should
  #  make sure the memory size is large enough to meet capsule PEI requirement in capsule update path.
  # @Prompt Stack size for CapsulePei transfer to long mode.
  gEfiMdeModulePkgTokenSpaceGuid.PcdCapsulePeiLongModeStackSize|0x8000|UINT32|0x0001005D

  ## Indicates if 1G page table will be enabled.<BR><BR>
  #   TRUE  - 1G page table will be enabled.<BR>
  #   FALSE - 1G page table will not be enabled.<BR>
  # @Prompt Enable 1G page table support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdUse1GPageTable|FALSE|BOOLEAN|0x0001005E

  ## Indicates if the Single Root I/O virtualization is supported.<BR><BR>
  #   TRUE  - Single Root I/O virtualization is supported.<BR>
  #   FALSE - Single Root I/O virtualization is not supported.<BR>
  # @Prompt Enable SRIOV support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSrIovSupport|TRUE|BOOLEAN|0x10000044

  ## Indicates if the Alternative Routing-ID is supported.<BR><BR>
  #   TRUE  - Alternative Routing-ID is supported.<BR>
  #   FALSE - Alternative Routing-ID is not supported.<BR>
  # @Prompt Enable ARI support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAriSupport|TRUE|BOOLEAN|0x10000045

  ## Indicates if the Multi Root I/O virtualization is supported.<BR><BR>
  #   TRUE  - Multi Root I/O virtualization is supported.<BR>
  #   FALSE - Multi Root I/O virtualization is not supported.<BR>
  # @Prompt Enable MRIOV support.
  gEfiMdeModulePkgTokenSpaceGuid.PcdMrIovSupport|FALSE|BOOLEAN|0x10000046

  ## Single root I/O virtualization virtual function memory BAR alignment.<BR><BR>
  #  BITN set indicates 2 of n+12 power<BR>
  #  BIT0 set indicates 4KB alignment<BR>
  #  BIT1 set indicates 8KB alignment<BR>
  # @Prompt SRIOV system page size.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSrIovSystemPageSize|0x1|UINT32|0x10000047

  ## SMBIOS version.
  # @Prompt SMBIOS version.
  gEfiMdeModulePkgTokenSpaceGuid.PcdSmbiosVersion|0x0207|UINT16|0x00010055

  ## This PCD specifies the additional pad size in FPDT Basic Boot Performance Table for
  #  the extension FPDT boot records received after ReadyToBoot and before ExitBootService.
  # @Prompt Pad size for extension FPDT boot records.
  gEfiMdeModulePkgTokenSpaceGuid.PcdExtFpdtBootRecordPadSize|0x0|UINT32|0x0001005F

  ## Indicates if ConIn device are connected on demand.<BR><BR>
  #   TRUE  - ConIn device are not connected during BDS and ReadKeyStroke/ReadKeyStrokeEx produced
  #           by Consplitter should be called before any real key read operation.<BR>
  #   FALSE - ConIn device may be connected normally during BDS.<BR>
  # @Prompt ConIn connect on demand.
  gEfiMdeModulePkgTokenSpaceGuid.PcdConInConnectOnDemand|FALSE|BOOLEAN|0x10000060

  ## Indicates if the S.M.A.R.T feature of attached ATA hard disks will be enabled.<BR><BR>
  #   TRUE  - S.M.A.R.T feature of attached ATA hard disks will be enabled.<BR>
  #   FALSE - S.M.A.R.T feature of attached ATA hard disks will be default status.<BR>
  # @Prompt Enable ATA S.M.A.R.T feature.
  gEfiMdeModulePkgTokenSpaceGuid.PcdAtaSmartEnable|TRUE|BOOLEAN|0x00010065

  ## Indicates if full PCI enumeration is disabled.<BR><BR>
  #   TRUE  - Full PCI enumeration is disabled.<BR>
  #   FALSE - Full PCI enumeration is not disabled.<BR>
  # @Prompt Disable full PCI enumeration.
  gEfiMdeModulePkgTokenSpaceGuid.PcdPciDisableBusEnumeration|FALSE|BOOLEAN|0x10000048

  ## Disk I/O - Number of Data Buffer block.
  # Define the size in block of the pre-allocated buffer. It provide better
  # performance for large Disk I/O requests.
  # @Prompt Disk I/O - Number of Data Buffer block.
  gEfiMdeModulePkgTokenSpaceGuid.PcdDiskIoDataBufferBlockNum|64|UINT32|0x30001039

[PcdsPatchableInModule]
  ## Specify memory size with page number for PEI code when
  #  Loading Module at Fixed Address feature is enabled.
  #  The value will be set by the build tool.
  # @Prompt LMFA PEI code page number.
  # @ValidList  0x80000001 | 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdLoadFixAddressPeiCodePageNumber|0|UINT32|0x00000029
  
  ## Specify memory size with page number for DXE boot time code when
  #  Loading Module at Fixed Address feature is enabled.
  #  The value will be set by the build tool.
  # @Prompt LMFA DXE boot code page number.
  # @ValidList  0x80000001 | 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdLoadFixAddressBootTimeCodePageNumber|0|UINT32|0x0000002a
  
  ## Specify memory size with page number for DXE runtime code when
  #  Loading Module at Fixed Address feature is enabled.
  #  The value will be set by the build tool.
  # @Prompt LMFA DXE runtime code page number.
  # @ValidList  0x80000001 | 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdLoadFixAddressRuntimeCodePageNumber|0|UINT32|0x0000002b
 
  ## Specify memory size with page number for SMM code when
  #  Loading Module at Fixed Address feature is enabled.
  #  The value will be set by the build tool.
  # @Prompt LMFA SMM code page number.
  # @ValidList  0x80000001 | 0
  gEfiMdeModulePkgTokenSpaceGuid.PcdLoadFixAddressSmmCodePageNumber|0|UINT32|0x0000002c

[PcdsDynamic, PcdsDynamicEx]
  ## This dynamic PCD hold an address to point to private data structure used in DxeS3BootScriptLib library
  #  instance which records the S3 boot script table start address, length, etc. To introduce this PCD is
  #  only for DxeS3BootScriptLib instance implementation purpose. The platform developer should make sure the
  #  default value is set to Zero. And the PCD is assumed ONLY to be accessed in DxeS3BootScriptLib Library.
  # @Prompt S3 Boot Script Table Private Data pointer.
  # @ValidList  0x80000001 | 0x0
  gEfiMdeModulePkgTokenSpaceGuid.PcdS3BootScriptTablePrivateDataPtr|0x0|UINT64|0x00030000

  ## This dynamic PCD hold an address to point to private data structure SMM copy used in DxeS3BootScriptLib library
  #  instance which records the S3 boot script table start address, length, etc. To introduce this PCD is
  #  only for DxeS3BootScriptLib instance implementation purpose. The platform developer should make sure the
  #  default value is set to Zero. And the PCD is assumed ONLY to be accessed in DxeS3BootScriptLib Library.
  # @Prompt S3 Boot Script Table Private Smm Data pointer.
  # @ValidList  0x80000001 | 0x0
  gEfiMdeModulePkgTokenSpaceGuid.PcdS3BootScriptTablePrivateSmmDataPtr|0x0|UINT64|0x00030001

  ## This dynamic PCD hold an address to point to the memory of page table. The page table establishes a 1:1 
  #  Virtual to Physical mapping according to the processor physical address bits.
  # @Prompt Identify Mapping Page Table pointer.
  # @ValidList  0x80000001 | 0x0
  gEfiMdeModulePkgTokenSpaceGuid.PcdIdentifyMappingPageTablePtr|0x0|UINT64|0x00030002

[UserExtensions.TianoCore."ExtraFiles"]
  MdeModulePkgExtra.uni