Merge tag 'asoc-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Updates for v5.2

This is a pretty huge set of changes, it's been a pretty active release
all round but the big thing with this release is the Sound Open Firmware
changes from Intel, providing another DSP framework for use with the
DSPs in their SoCs.  This one works with the firmware of the same name
which is free software (unlike the previous DSP firmwares and framework)
and there has been some interest in adoption by other systems already so
hopefully we will see adoption by other vendors in the future.

Other highlights include:

 - Support for MCLK/sample rate ratio setting in the generic cards.
 - Support for pin switches in the generic cards.
 - A big set of improvements to the TLV320AIC32x4 drivers from Annaliese
   McDermond.
 - New drivers for Freescale audio mixers, several Intel machines,
   several Mediatek machines, Meson G12A, Sound Open Firmware and
   Spreadtrum compressed audio and DMA devices.

1 files changed, 66 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
index bbcb255c3150..93a7469e70d4 100644
--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -12,10 +12,15 @@ Required properties:
 Subnodes:
 
 The integrated switch subnode should be specified according to the binding
-described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of
-port and PHY id, each subnode describing a port needs to have a valid phandle
-referencing the internal PHY connected to it. The CPU port of this switch is
-always port 0.
+described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
+mdio-bus each subnode describing a port needs to have a valid phandle
+referencing the internal PHY it is connected to. This is because there's no
+N:N mapping of port and PHY id.
+
+Don't use mixed external and internal mdio-bus configurations, as this is
+not supported by the hardware.
+
+The CPU port of this switch is always port 0.
 
 A CPU port node has the following optional node:
 
@@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties:
 - 'full-duplex' (boolean, optional), to indicate that full duplex is
   used. When absent, half duplex is assumed.
 
-Example:
+Examples:
 
+for the external mdio-bus configuration:
 
 	&mdio0 {
 		phy_port1: phy@0 {
@@ -55,12 +61,12 @@ Example:
 			reg = <4>;
 		};
 
-		switch0@0 {
+		switch@10 {
 			compatible = "qca,qca8337";
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			reg = <0>;
+			reg = <0x10>;
 
 			ports {
 				#address-cells = <1>;
@@ -108,3 +114,56 @@ Example:
 			};
 		};
 	};
+
+for the internal master mdio-bus configuration:
+
+	&mdio0 {
+		switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+					fixed-link {
+						speed = 1000;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "wan";
+				};
+			};
+		};
+	};