Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is a calm cycle, not much happened this time around: not even
  much incremental development. Some three new drivers, that is all.

  No core changes.

  New drivers:

   - NXP (ex Freescale) i.MX 8QM driver.

   - NXP (ex Freescale) i.MX 8MM driver.

   - AT91 SAM9X60 subdriver.

  Improvements:

   - Support for external interrups (EINT) on Mediatek virtual GPIOs.

   - Make BCM2835 pin config fully generic.

   - Lots of Renesas SH-PFC incremental improvements"

* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
  pinctrl: imx: fix scu link errors
  dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
  pinctrl: qcom: spmi-gpio: Reorder debug print
  pinctrl: nomadik: fix possible object reference leak
  pinctrl: stm32: return error upon hwspinlock failure
  pinctrl: stm32: fix memory leak issue
  pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
  pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
  pinctrl: sh-pfc: Validate fixed-size field widths at build time
  pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
  pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
  pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
  pinctrl: sh-pfc: emev2: Add missing pinmux functions
  pinctrl: sunxi: Support I/O bias voltage setting on A80
  pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
  pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
  pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
  pinctrl: bcm2835: declare pin config as generic
  pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
  dt-bindings: add documentation for slew rate
  ...

6 files changed, 117 insertions, 21 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index 3e23fece99da..eb39f5051159 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -19,7 +19,7 @@ such as pull-up, multi drive, etc.
 
 Required properties for iomux controller:
 - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
-		or "atmel,sama5d3-pinctrl"
+		or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl"
 - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
   configured in this periph mode. All the periph and bank need to be describe.
 
@@ -100,6 +100,7 @@ DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the
 				11 - High
 OUTPUT		(1 << 7): indicate this pin need to be configured as an output.
 OUTPUT_VAL	(1 << 8): output val (1 = high, 0 = low)
+SLEWRATE	(1 << 9): slew rate of the pin: 0 = disable, 1 = enable
 DEBOUNCE	(1 << 16): indicate this pin needs debounce.
 DEBOUNCE_VAL	(0x3fff << 17): debounce value.
 
@@ -116,6 +117,19 @@ Some requirements for using atmel,at91rm9200-pinctrl binding:
    configurations by referring to the phandle of that pin configuration node.
 4. The gpio controller must be describe in the pinctrl simple-bus.
 
+For each bank the required properties are:
+- compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or
+  "microchip,sam9x60-gpio"
+- reg: physical base address and length of the controller's registers
+- interrupts: interrupt outputs from the controller
+- interrupt-controller: marks the device node as an interrupt controller
+- #interrupt-cells: should be 2; refer to ../interrupt-controller/interrupts.txt
+  for more details.
+- gpio-controller
+- #gpio-cells: should be 2; the first cell is the GPIO number and the second
+  cell specifies GPIO flags as defined in <dt-bindings/gpio/gpio.h>.
+- clocks: bank clock
+
 Examples:
 
 pinctrl@fffff400 {
@@ -125,6 +139,17 @@ pinctrl@fffff400 {
 	compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
 	reg = <0xfffff400 0x600>;
 
+	pioA: gpio@fffff400 {
+		compatible = "atmel,at91sam9x5-gpio";
+		reg = <0xfffff400 0x200>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+	};
+
 	atmel,mux-mask = <
 	      /*    A         B     */
 	       0xffffffff 0xffc00c3b  /* pioA */
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt
new file mode 100644
index 000000000000..6da01d619d33
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt
@@ -0,0 +1,32 @@
+* Freescale IMX50 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx50-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx50 datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_HVE			(1 << 13)
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE			(1 << 3)
+PAD_CTL_DSE_LOW			(0 << 1)
+PAD_CTL_DSE_MED			(1 << 1)
+PAD_CTL_DSE_HIGH		(2 << 1)
+PAD_CTL_DSE_MAX			(3 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx50-pinfunc.h in device tree source folder for all available
+imx50 PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt
new file mode 100644
index 000000000000..524a16fca666
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt
@@ -0,0 +1,36 @@
+* Freescale IMX8MM IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory
+for common binding part and usage.
+
+Required properties:
+- compatible: "fsl,imx8mm-iomuxc"
+- reg: should contain the base physical address and size of the iomuxc
+  registers.
+
+Required properties in sub-nodes:
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  <dt-bindings/pinctrl/imx8mm-pinfunc.h>. The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX8M Mini
+  Reference Manual for detailed CONFIG settings.
+
+Examples:
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart1>;
+};
+
+iomuxc: pinctrl@30330000 {
+        compatible = "fsl,imx8mm-iomuxc";
+        reg = <0x0 0x30330000 0x0 0x10000>;
+
+        pinctrl_uart1: uart1grp {
+                fsl,pins = <
+                        MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX             0x140
+                        MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX             0x140
+                >;
+        };
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt
index c7c088d2dd50..38dc56a57760 100644
--- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt
@@ -58,11 +58,11 @@ group pwm3
  - functions pwm, gpio
 
 group pmic1
- - pin 17
+ - pin 7
  - functions pmic, gpio
 
 group pmic0
- - pin 16
+ - pin 6
  - functions pmic, gpio
 
 group i2c2
@@ -112,19 +112,31 @@ group usb2_drvvbus1
  - functions drvbus, gpio
 
 group sdio_sb
- - pins 60-64
+ - pins 60-65
  - functions sdio, gpio
 
 group rgmii
- - pins 42-55
+ - pins 42-53
  - functions mii, gpio
 
 group pcie1
- - pins 39-40
+ - pins 39
+ - functions pcie, gpio
+
+group pcie1_clkreq
+ - pins 40
  - functions pcie, gpio
 
+group pcie1_wakeup
+ - pins 41
+ - functions pcie, gpio
+
+group smi
+ - pins 54-55
+ - functions smi, gpio
+
 group ptp
- - pins 56-58
+ - pins 56
  - functions ptp, gpio
 
 group ptp_clk
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
index 82ead40311f6..a47dd990a8d3 100644
--- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -23,11 +23,11 @@ The GPIO bank for the controller is represented as a sub-node and it acts as a
 GPIO controller.
 
 Required properties for sub-nodes are:
- - reg: should contain address and size for mux, pull-enable, pull and
-   gpio register sets
- - reg-names: an array of strings describing the "reg" entries. Must
-   contain "mux", "pull" and "gpio". "pull-enable" is optional and
-   when it is missing the "pull" registers are used instead
+ - reg: should contain a list of address and size, one tuple for each entry
+   in reg-names.
+ - reg-names: an array of strings describing the "reg" entries.
+   Must contain "mux" and "gpio".
+   May contain "pull", "pull-enable" and "ds" when appropriate.
  - gpio-controller: identifies the node as a gpio controller
  - #gpio-cells: must be 2
 
diff --git a/Documentation/driver-api/pinctl.rst b/Documentation/driver-api/pinctl.rst
index 6cb68d67fa75..2bb1bc484278 100644
--- a/Documentation/driver-api/pinctl.rst
+++ b/Documentation/driver-api/pinctl.rst
@@ -274,15 +274,6 @@ configuration in the pin controller ops like this::
 		.confops = &foo_pconf_ops,
 	};
 
-Since some controllers have special logic for handling entire groups of pins
-they can exploit the special whole-group pin control function. The
-pin_config_group_set() callback is allowed to return the error code -EAGAIN,
-for groups it does not want to handle, or if it just wants to do some
-group-level handling and then fall through to iterate over all pins, in which
-case each individual pin will be treated by separate pin_config_set() calls as
-well.
-
-
 Interaction with the GPIO subsystem
 ===================================