phy: add inno-usb2-phy driver for hi3798cv200 SoC

It adds inno-usb2-phy driver for hi3798cv200 SoC USB 2.0 support.  One
inno-usb2-phy device can support up to two PHY ports.  While there is
device level reference clock and power reset to be controlled, each PHY
port has its own utmi reset that needs to assert/de-assert as needed.

Hi3798cv200 needs to access PHY port0 register via particular peripheral
syscon controller register to control PHY, like turning on PHY clock.

Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

1 files changed, 197 insertions, 0 deletions

diff --git a/drivers/phy/hisilicon/phy-hisi-inno-usb2.c b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
new file mode 100644
index 000000000000..524381249a2b
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
@@ -0,0 +1,197 @@
+/*
+ * HiSilicon INNO USB2 PHY Driver.
+ *
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/reset.h>
+
+#define INNO_PHY_PORT_NUM	2
+#define REF_CLK_STABLE_TIME	100	/* unit:us */
+#define UTMI_CLK_STABLE_TIME	200	/* unit:us */
+#define TEST_CLK_STABLE_TIME	2	/* unit:ms */
+#define PHY_CLK_STABLE_TIME	2	/* unit:ms */
+#define UTMI_RST_COMPLETE_TIME	2	/* unit:ms */
+#define POR_RST_COMPLETE_TIME	300	/* unit:us */
+#define PHY_TEST_DATA		GENMASK(7, 0)
+#define PHY_TEST_ADDR		GENMASK(15, 8)
+#define PHY_TEST_PORT		GENMASK(18, 16)
+#define PHY_TEST_WREN		BIT(21)
+#define PHY_TEST_CLK		BIT(22)	/* rising edge active */
+#define PHY_TEST_RST		BIT(23)	/* low active */
+#define PHY_CLK_ENABLE		BIT(2)
+
+struct hisi_inno_phy_port {
+	struct reset_control *utmi_rst;
+	struct hisi_inno_phy_priv *priv;
+};
+
+struct hisi_inno_phy_priv {
+	void __iomem *mmio;
+	struct clk *ref_clk;
+	struct reset_control *por_rst;
+	struct hisi_inno_phy_port ports[INNO_PHY_PORT_NUM];
+};
+
+static void hisi_inno_phy_write_reg(struct hisi_inno_phy_priv *priv,
+				    u8 port, u32 addr, u32 data)
+{
+	void __iomem *reg = priv->mmio;
+	u32 val;
+
+	val = (data & PHY_TEST_DATA) |
+	      ((addr << 8) & PHY_TEST_ADDR) |
+	      ((port << 16) & PHY_TEST_PORT) |
+	      PHY_TEST_WREN | PHY_TEST_RST;
+	writel(val, reg);
+
+	val |= PHY_TEST_CLK;
+	writel(val, reg);
+
+	val &= ~PHY_TEST_CLK;
+	writel(val, reg);
+}
+
+static void hisi_inno_phy_setup(struct hisi_inno_phy_priv *priv)
+{
+	/* The phy clk is controlled by the port0 register 0x06. */
+	hisi_inno_phy_write_reg(priv, 0, 0x06, PHY_CLK_ENABLE);
+	msleep(PHY_CLK_STABLE_TIME);
+}
+
+static int hisi_inno_phy_init(struct phy *phy)
+{
+	struct hisi_inno_phy_port *port = phy_get_drvdata(phy);
+	struct hisi_inno_phy_priv *priv = port->priv;
+	int ret;
+
+	ret = clk_prepare_enable(priv->ref_clk);
+	if (ret)
+		return ret;
+	udelay(REF_CLK_STABLE_TIME);
+
+	reset_control_deassert(priv->por_rst);
+	udelay(POR_RST_COMPLETE_TIME);
+
+	/* Set up phy registers */
+	hisi_inno_phy_setup(priv);
+
+	reset_control_deassert(port->utmi_rst);
+	udelay(UTMI_RST_COMPLETE_TIME);
+
+	return 0;
+}
+
+static int hisi_inno_phy_exit(struct phy *phy)
+{
+	struct hisi_inno_phy_port *port = phy_get_drvdata(phy);
+	struct hisi_inno_phy_priv *priv = port->priv;
+
+	reset_control_assert(port->utmi_rst);
+	reset_control_assert(priv->por_rst);
+	clk_disable_unprepare(priv->ref_clk);
+
+	return 0;
+}
+
+static const struct phy_ops hisi_inno_phy_ops = {
+	.init = hisi_inno_phy_init,
+	.exit = hisi_inno_phy_exit,
+	.owner = THIS_MODULE,
+};
+
+static int hisi_inno_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct hisi_inno_phy_priv *priv;
+	struct phy_provider *provider;
+	struct device_node *child;
+	struct resource *res;
+	int i = 0;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->mmio = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->mmio)) {
+		ret = PTR_ERR(priv->mmio);
+		return ret;
+	}
+
+	priv->ref_clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->ref_clk))
+		return PTR_ERR(priv->ref_clk);
+
+	priv->por_rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(priv->por_rst))
+		return PTR_ERR(priv->por_rst);
+
+	for_each_child_of_node(np, child) {
+		struct reset_control *rst;
+		struct phy *phy;
+
+		rst = of_reset_control_get_exclusive(child, NULL);
+		if (IS_ERR(rst))
+			return PTR_ERR(rst);
+		priv->ports[i].utmi_rst = rst;
+		priv->ports[i].priv = priv;
+
+		phy = devm_phy_create(dev, child, &hisi_inno_phy_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		phy_set_bus_width(phy, 8);
+		phy_set_drvdata(phy, &priv->ports[i]);
+		i++;
+
+		if (i > INNO_PHY_PORT_NUM) {
+			dev_warn(dev, "Support %d ports in maximum\n", i);
+			break;
+		}
+	}
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id hisi_inno_phy_of_match[] = {
+	{ .compatible = "hisilicon,inno-usb2-phy", },
+	{ .compatible = "hisilicon,hi3798cv200-usb2-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hisi_inno_phy_of_match);
+
+static struct platform_driver hisi_inno_phy_driver = {
+	.probe	= hisi_inno_phy_probe,
+	.driver = {
+		.name	= "hisi-inno-phy",
+		.of_match_table	= hisi_inno_phy_of_match,
+	}
+};
+module_platform_driver(hisi_inno_phy_driver);
+
+MODULE_DESCRIPTION("HiSilicon INNO USB2 PHY Driver");
+MODULE_LICENSE("GPL v2");