diff options
| -rwxr-xr-x | Documentation/sound/cards/multisound.sh | 72 |
1 files changed, 36 insertions, 36 deletions
diff --git a/Documentation/sound/cards/multisound.sh b/Documentation/sound/cards/multisound.sh index 0e0cb029421b..a915a1affcde 100755 --- a/Documentation/sound/cards/multisound.sh +++ b/Documentation/sound/cards/multisound.sh @@ -34,12 +34,12 @@ # composed of the following modules (these can also operate compiled # into the kernel): # -# msnd - MultiSound base (requires soundcore) +# snd-msnd-lib - MultiSound base (requires snd) # -# msnd_classic - Base audio/mixer support for Classic, Monetery and -# Tahiti cards +# snd-msnd-classic - Base audio/mixer support for Classic, Monetery and +# Tahiti cards # -# msnd_pinnacle - Base audio/mixer support for Pinnacle and Fiji cards +# snd-msnd-pinnacle - Base audio/mixer support for Pinnacle and Fiji cards # # # Important Notes - Read Before Using @@ -66,7 +66,7 @@ # # * Classic/Monterey/Tahiti # -# These cards are configured through the driver msnd_classic. You must +# These cards are configured through the driver snd-msnd-classic. You must # know the io port, then the driver will select the irq and memory resources # on the card. It is up to you to know if these are free locations or now, # a conflict can lock the machine up. @@ -81,10 +81,10 @@ # can be used to configure the card in non-PnP mode, and in PnP mode # you can use isapnptools. These are described briefly here. # -# pinnaclecfg is not required; you can use the msnd_pinnacle module +# pinnaclecfg is not required; you can use the snd-msnd-pinnacle module # to fully configure the card as well. However, pinnaclecfg can be # used to change the resource values of a particular device after the -# msnd_pinnacle module has been loaded. If you are compiling the +# snd-msnd-pinnacle module has been loaded. If you are compiling the # driver into the kernel, you must set these values during compile # time, however other peripheral resource values can be changed with # the pinnaclecfg program after the kernel is loaded. @@ -96,7 +96,7 @@ # to obtain one with the command `pnpdump 1 0x203' -- this may vary # for you (running pnpdump by itself did not work for me). Then, # edit this file and use isapnp to uncomment and set the card values. -# Use these values when inserting the msnd_pinnacle module. Using +# Use these values when inserting the snd-msnd-pinnacle module. Using # this method, you can set the resources for the DSP and the Kurzweil # synth (Pinnacle). Since Linux does not directly support PnP # devices, you may have difficulty when using the card in PnP mode @@ -133,16 +133,16 @@ # pinnaclecfg program. Using this program, you can assign the # resource values to the card's devices, or disable the devices. As # an alternative to using pinnaclecfg, you can specify many of the -# configuration values when loading the msnd_pinnacle module (or +# configuration values when loading the snd-msnd-pinnacle module (or # during kernel configuration when compiling the driver into the # kernel). # -# If you specify cfg=0x250 for the msnd_pinnacle module, it +# If you specify cfg=0x250 for the snd-msnd-pinnacle module, it # automatically configure the card to the given io, irq and memory # values using that config port (the config port is jumper selectable # on the card to 0x250, 0x260 or 0x270). # -# See the `msnd_pinnacle Additional Options' section below for more +# See the `snd-msnd-pinnacle Additional Options' section below for more # information on these parameters (also, if you compile the driver # directly into the kernel, these extra parameters can be useful # here). @@ -157,44 +157,44 @@ # # * MultiSound Classic/Monterey/Tahiti: # -# modprobe soundcore -# insmod msnd -# insmod msnd_classic io=0x290 irq=7 mem=0xd0000 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-classic io=0x290 irq=7 mem=0xd0000 # # * MultiSound Pinnacle in PnP mode: # -# modprobe soundcore -# insmod msnd +# modprobe snd +# insmod snd-msnd-lib # isapnp mypinnacle.conf -# insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values +# insmod snd-msnd-pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values # # * MultiSound Pinnacle in non-PnP mode (replace 0x250 with your configuration port, # one of 0x250, 0x260 or 0x270): # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 # # * To use the MPU-compatible Kurzweil synth on the Pinnacle in PnP # mode, add the following (assumes you did `isapnp mypinnacle.conf'): # -# insmod sound +# insmod snd # insmod mpu401 io=0x330 irq=9 <-- match mypinnacle.conf values # # * To use the MPU-compatible Kurzweil synth on the Pinnacle in non-PnP # mode, add the following. Note how we first configure the peripheral's # resources, _then_ install a Linux driver for it: # -# insmod sound +# insmod snd # pinnaclecfg 0x250 mpu 0x330 9 # insmod mpu401 io=0x330 irq=9 # # -- OR you can use the following sequence without pinnaclecfg in non-PnP mode: # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9 -# insmod sound +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9 +# insmod snd # insmod mpu401 io=0x330 irq=9 # # * To setup the joystick port on the Pinnacle in non-PnP mode (though @@ -203,15 +203,15 @@ # # pinnaclecfg 0x250 joystick 0x200 # -# -- OR you can configure this using msnd_pinnacle with the following: +# -- OR you can configure this using snd-msnd-pinnacle with the following: # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200 # # -# msnd_classic, msnd_pinnacle Required Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-classic, snd-msnd-pinnacle Required Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # If the following options are not given, the module will not load. # Examine the kernel message log for informative error messages. @@ -223,8 +223,8 @@ # mem Shared memory area, e.g. mem=0xd8000 # # -# msnd_classic, msnd_pinnacle Additional Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-classic, snd-msnd-pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # fifosize The digital audio FIFOs, in kilobytes. If not # specified, the default will be used. Increasing @@ -244,8 +244,8 @@ # to zero). # # -# msnd_pinnacle Additional Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # digital Specify digital=1 to enable the S/PDIF input # if you have the digital daughterboard |