diff options
| -rw-r--r-- | Documentation/devicetree/bindings/clock/at91-clock.txt | 516 |
1 files changed, 21 insertions, 495 deletions
diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 8f8f95056f3d..e9f70fcdfe80 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -4,6 +4,8 @@ This binding uses the common clock binding[1]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt +Slow Clock controller: + Required properties: - compatible : shall be one of the following: "atmel,at91sam9x5-sckc" or @@ -16,84 +18,6 @@ Required properties: "atmel,at91sam9x5-clk-slow-rc-osc": at91 internal slow RC oscillator - - "atmel,<chip>-pmc": - at91 PMC (Power Management Controller) - All at91 specific clocks (clocks defined below) must be child - node of the PMC node. - <chip> can be: at91rm9200, at91sam9260, at91sam9261, - at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5, - sama5d2, sama5d3 or sama5d4. - - "atmel,at91sam9x5-clk-slow" (under sckc node) - or - "atmel,at91sam9260-clk-slow" (under pmc node): - at91 slow clk - - "atmel,at91rm9200-clk-main-osc" - "atmel,at91sam9x5-clk-main-rc-osc" - at91 main clk sources - - "atmel,at91sam9x5-clk-main" - "atmel,at91rm9200-clk-main": - at91 main clock - - "atmel,at91rm9200-clk-master" or - "atmel,at91sam9x5-clk-master": - at91 master clock - - "atmel,at91sam9x5-clk-peripheral" or - "atmel,at91rm9200-clk-peripheral": - at91 peripheral clocks - - "atmel,at91rm9200-clk-pll" or - "atmel,at91sam9g45-clk-pll" or - "atmel,at91sam9g20-clk-pllb" or - "atmel,sama5d3-clk-pll": - at91 pll clocks - - "atmel,at91sam9x5-clk-plldiv": - at91 plla divisor - - "atmel,at91rm9200-clk-programmable" or - "atmel,at91sam9g45-clk-programmable" or - "atmel,at91sam9x5-clk-programmable": - at91 programmable clocks - - "atmel,at91sam9x5-clk-smd": - at91 SMD (Soft Modem) clock - - "atmel,at91rm9200-clk-system": - at91 system clocks - - "atmel,at91rm9200-clk-usb" or - "atmel,at91sam9x5-clk-usb" or - "atmel,at91sam9n12-clk-usb": - at91 usb clock - - "atmel,at91sam9x5-clk-utmi": - at91 utmi clock - - "atmel,sama5d4-clk-h32mx": - at91 h32mx clock - - "atmel,sama5d2-clk-generated": - at91 generated clock - - "atmel,sama5d2-clk-audio-pll-frac": - at91 audio fractional pll - - "atmel,sama5d2-clk-audio-pll-pad": - at91 audio pll CLK_AUDIO output pin - - "atmel,sama5d2-clk-audio-pll-pmc" - at91 audio pll output on AUDIOPLLCLK that feeds the PMC - and can be used by peripheral clock or generic clock - - "atmel,sama5d2-clk-i2s-mux" (under pmc node): - at91 I2S clock source selection - -Required properties for SCKC node: - reg : defines the IO memory reserved for the SCKC. - #size-cells : shall be 0 (reg is used to encode clk id). - #address-cells : shall be 1 (reg is used to encode clk id). @@ -109,428 +33,30 @@ For example: /* put at91 slow clocks here */ }; +Power Management Controller (PMC): -Required properties for internal slow RC oscillator: -- #clock-cells : from common clock binding; shall be set to 0. -- clock-frequency : define the internal RC oscillator frequency. - -Optional properties: -- clock-accuracy : define the internal RC oscillator accuracy. - -For example: - slow_rc_osc: slow_rc_osc { - compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; - clock-frequency = <32768>; - clock-accuracy = <50000000>; - }; - -Required properties for slow oscillator: -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall encode the main osc source clk sources (see atmel datasheet). +Required properties: +- compatible : shall be "atmel,<chip>-pmc", "syscon": + <chip> can be: at91rm9200, at91sam9260, at91sam9261, + at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9g15, + at91sam9g25, at91sam9g35, at91sam9x25, at91sam9x35, at91sam9x5, + sama5d2, sama5d3 or sama5d4. +- #clock-cells : from common clock binding; shall be set to 2. The first entry + is the type of the clock (core, system, peripheral or generated) and the + second entry its index as provided by the datasheet +- clocks : Must contain an entry for each entry in clock-names. +- clock-names: Must include the following entries: "slow_clk", "main_xtal" Optional properties: - atmel,osc-bypass : boolean property. Set this when a clock signal is directly provided on XIN. For example: - slow_osc: slow_osc { - compatible = "atmel,at91rm9200-clk-slow-osc"; - #clock-cells = <0>; - clocks = <&slow_xtal>; - }; - -Required properties for slow clock: -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall encode the slow clk sources (see atmel datasheet). - -For example: - clk32k: slck { - compatible = "atmel,at91sam9x5-clk-slow"; - #clock-cells = <0>; - clocks = <&slow_rc_osc &slow_osc>; - }; - -Required properties for PMC node: -- reg : defines the IO memory reserved for the PMC. -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). -- interrupts : shall be set to PMC interrupt line. -- interrupt-controller : tell that the PMC is an interrupt controller. -- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, - and reflect the bit position in the PMC_ER/DR/SR registers. - You can use the dt macros defined in dt-bindings/clock/at91.h. - 0 (AT91_PMC_MOSCS) -> main oscillator ready - 1 (AT91_PMC_LOCKA) -> PLL A ready - 2 (AT91_PMC_LOCKB) -> PLL B ready - 3 (AT91_PMC_MCKRDY) -> master clock ready - 6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready - 8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready - 16 (AT91_PMC_MOSCSELS) -> main oscillator selected - 17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized - 18 (AT91_PMC_CFDEV) -> clock failure detected - -For example: - pmc: pmc@fffffc00 { - compatible = "atmel,sama5d3-pmc"; - interrupts = <1 4 7>; - interrupt-controller; - #interrupt-cells = <2>; - #size-cells = <0>; - #address-cells = <1>; - - /* put at91 clocks here */ - }; - -Required properties for main clock internal RC oscillator: -- interrupts : shall be set to "<0>". -- clock-frequency : define the internal RC oscillator frequency. - -Optional properties: -- clock-accuracy : define the internal RC oscillator accuracy. - -For example: - main_rc_osc: main_rc_osc { - compatible = "atmel,at91sam9x5-clk-main-rc-osc"; - interrupt-parent = <&pmc>; - interrupts = <0>; - clock-frequency = <12000000>; - clock-accuracy = <50000000>; - }; - -Required properties for main clock oscillator: -- interrupts : shall be set to "<0>". -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall encode the main osc source clk sources (see atmel datasheet). - -Optional properties: -- atmel,osc-bypass : boolean property. Specified if a clock signal is provided - on XIN. - - clock signal is directly provided on XIN pin. - -For example: - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - interrupt-parent = <&pmc>; - interrupts = <0>; - #clock-cells = <0>; - clocks = <&main_xtal>; - }; - -Required properties for main clock: -- interrupts : shall be set to "<0>". -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall encode the main clk sources (see atmel datasheet). - -For example: - main: mainck { - compatible = "atmel,at91sam9x5-clk-main"; - interrupt-parent = <&pmc>; - interrupts = <0>; - #clock-cells = <0>; - clocks = <&main_rc_osc &main_osc>; - }; - -Required properties for master clock: -- interrupts : shall be set to "<3>". -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the master clock sources (see atmel datasheet) phandles. - e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>". -- atmel,clk-output-range : minimum and maximum clock frequency (two u32 - fields). - e.g. output = <0 133000000>; <=> 0 to 133MHz. -- atmel,clk-divisors : master clock divisors table (four u32 fields). - 0 <=> reserved value. - e.g. divisors = <1 2 4 6>; -- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the - PRES field as CLOCK_DIV3 (e.g sam9x5). - -For example: - mck: mck { - compatible = "atmel,at91rm9200-clk-master"; - interrupt-parent = <&pmc>; - interrupts = <3>; - #clock-cells = <0>; - atmel,clk-output-range = <0 133000000>; - atmel,clk-divisors = <1 2 4 0>; - }; - -Required properties for peripheral clocks: -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). -- clocks : shall be the master clock phandle. - e.g. clocks = <&mck>; -- name: device tree node describing a specific peripheral clock. - * #clock-cells : from common clock binding; shall be set to 0. - * reg: peripheral id. See Atmel's datasheets to get a full - list of peripheral ids. - * atmel,clk-output-range : minimum and maximum clock frequency - (two u32 fields). Only valid on at91sam9x5-clk-peripheral - compatible IPs. - -For example: - periph: periphck { - compatible = "atmel,at91sam9x5-clk-peripheral"; - #size-cells = <0>; - #address-cells = <1>; - clocks = <&mck>; - - ssc0_clk { - #clock-cells = <0>; - reg = <2>; - atmel,clk-output-range = <0 133000000>; - }; - - usart0_clk { - #clock-cells = <0>; - reg = <3>; - atmel,clk-output-range = <0 66000000>; - }; - }; - - -Required properties for pll clocks: -- interrupts : shall be set to "<1>". -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the main clock phandle. -- reg : pll id. - 0 -> PLL A - 1 -> PLL B -- atmel,clk-input-range : minimum and maximum source clock frequency (two u32 - fields). - e.g. input = <1 32000000>; <=> 1 to 32MHz. -- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output - range description. Sould be set to 2, 3 - or 4. - * 1st and 2nd cells represent the frequency range (min-max). - * 3rd cell is optional and represents the OUT field value for the given - range. - * 4th cell is optional and represents the ICPLL field (PLLICPR - register) -- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter - depending on #atmel,pll-output-range-cells - property value. - -For example: - plla: pllack { - compatible = "atmel,at91sam9g45-clk-pll"; - interrupt-parent = <&pmc>; - interrupts = <1>; - #clock-cells = <0>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <2000000 32000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <74500000 800000000 0 0 - 69500000 750000000 1 0 - 64500000 700000000 2 0 - 59500000 650000000 3 0 - 54500000 600000000 0 1 - 49500000 550000000 1 1 - 44500000 500000000 2 1 - 40000000 450000000 3 1>; - }; - -Required properties for plldiv clocks (plldiv = pll / 2): -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the plla clock phandle. - -The pll divisor is equal to 2 and cannot be changed. - -For example: - plladiv: plladivck { - compatible = "atmel,at91sam9x5-clk-plldiv"; - #clock-cells = <0>; - clocks = <&plla>; - }; - -Required properties for programmable clocks: -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). -- clocks : shall be the programmable clock source phandles. - e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; -- name: device tree node describing a specific prog clock. - * #clock-cells : from common clock binding; shall be set to 0. - * reg : programmable clock id (register offset from PCKx - register). - * interrupts : shall be set to "<(8 + id)>". - -For example: - prog: progck { - compatible = "atmel,at91sam9g45-clk-programmable"; - #size-cells = <0>; - #address-cells = <1>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; - - prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <8>; - }; - - prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <9>; - }; - }; - - -Required properties for smd clock: -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the smd clock source phandles. - e.g. clocks = <&plladiv>, <&utmi>; - -For example: - smd: smdck { - compatible = "atmel,at91sam9x5-clk-smd"; - #clock-cells = <0>; - clocks = <&plladiv>, <&utmi>; - }; - -Required properties for system clocks: -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). -- name: device tree node describing a specific system clock. - * #clock-cells : from common clock binding; shall be set to 0. - * reg: system clock id (bit position in SCER/SCDR/SCSR registers). - See Atmel's datasheet to get a full list of system clock ids. - -For example: - system: systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - ddrck { - #clock-cells = <0>; - reg = <2>; - clocks = <&mck>; - }; - - uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - }; - - -Required properties for usb clock: -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the smd clock source phandles. - e.g. clocks = <&pllb>; -- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"): - usb clock divisor table. - e.g. divisors = <1 2 4 0>; - -For example: - usb: usbck { - compatible = "atmel,at91sam9x5-clk-usb"; - #clock-cells = <0>; - clocks = <&plladiv>, <&utmi>; - }; - - usb: usbck { - compatible = "atmel,at91rm9200-clk-usb"; - #clock-cells = <0>; - clocks = <&pllb>; - atmel,clk-divisors = <1 2 4 0>; - }; - - -Required properties for utmi clock: -- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>". -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the main clock source phandle. - -For example: - utmi: utmick { - compatible = "atmel,at91sam9x5-clk-utmi"; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>; - #clock-cells = <0>; - clocks = <&main>; - }; - -Required properties for 32 bits bus Matrix clock (h32mx clock): -- #clock-cells : from common clock binding; shall be set to 0. -- clocks : shall be the master clock source phandle. - -For example: - h32ck: h32mxck { - #clock-cells = <0>; - compatible = "atmel,sama5d4-clk-h32mx"; - clocks = <&mck>; - }; - -Required properties for generated clocks: -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). -- clocks : shall be the generated clock source phandles. - e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; -- name: device tree node describing a specific generated clock. - * #clock-cells : from common clock binding; shall be set to 0. - * reg: peripheral id. See Atmel's datasheets to get a full - list of peripheral ids. - * atmel,clk-output-range : minimum and maximum clock frequency - (two u32 fields). - -For example: - gck { - compatible = "atmel,sama5d2-clk-generated"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; - - tcb0_gclk: tcb0_gclk { - #clock-cells = <0>; - reg = <35>; - atmel,clk-output-range = <0 83000000>; - }; - - pwm_gclk: pwm_gclk { - #clock-cells = <0>; - reg = <38>; - atmel,clk-output-range = <0 83000000>; - }; - }; - -Required properties for I2S mux clocks: -- #size-cells : shall be 0 (reg is used to encode I2S bus id). -- #address-cells : shall be 1 (reg is used to encode I2S bus id). -- name: device tree node describing a specific mux clock. - * #clock-cells : from common clock binding; shall be set to 0. - * clocks : shall be the mux clock parent phandles; shall be 2 phandles: - peripheral and generated clock; the first phandle shall belong to the - peripheral clock and the second one shall belong to the generated - clock; "clock-indices" property can be user to specify - the correct order. - * reg: I2S bus id of the corresponding mux clock. - e.g. reg = <0>; for i2s0, reg = <1>; for i2s1 - -For example: - i2s_clkmux { - compatible = "atmel,sama5d2-clk-i2s-mux"; - #address-cells = <1>; - #size-cells = <0>; - - i2s0muxck: i2s0_muxclk { - clocks = <&i2s0_clk>, <&i2s0_gclk>; - #clock-cells = <0>; - reg = <0>; - }; - - i2s1muxck: i2s1_muxclk { - clocks = <&i2s1_clk>, <&i2s1_gclk>; - #clock-cells = <0>; - reg = <1>; - }; + pmc: pmc@f0018000 { + compatible = "atmel,sama5d4-pmc", "syscon"; + reg = <0xf0018000 0x120>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + #clock-cells = <2>; + clocks = <&clk32k>, <&main_xtal>; + clock-names = "slow_clk", "main_xtal"; }; |