diff options
Diffstat (limited to 'Documentation/arm/omap/omap_pm.rst')
-rw-r--r-- | Documentation/arm/omap/omap_pm.rst | 165 |
1 files changed, 165 insertions, 0 deletions
diff --git a/Documentation/arm/omap/omap_pm.rst b/Documentation/arm/omap/omap_pm.rst new file mode 100644 index 000000000000..a335e4c8ce2c --- /dev/null +++ b/Documentation/arm/omap/omap_pm.rst @@ -0,0 +1,165 @@ +===================== +The OMAP PM interface +===================== + +This document describes the temporary OMAP PM interface. Driver +authors use these functions to communicate minimum latency or +throughput constraints to the kernel power management code. +Over time, the intention is to merge features from the OMAP PM +interface into the Linux PM QoS code. + +Drivers need to express PM parameters which: + +- support the range of power management parameters present in the TI SRF; + +- separate the drivers from the underlying PM parameter + implementation, whether it is the TI SRF or Linux PM QoS or Linux + latency framework or something else; + +- specify PM parameters in terms of fundamental units, such as + latency and throughput, rather than units which are specific to OMAP + or to particular OMAP variants; + +- allow drivers which are shared with other architectures (e.g., + DaVinci) to add these constraints in a way which won't affect non-OMAP + systems, + +- can be implemented immediately with minimal disruption of other + architectures. + + +This document proposes the OMAP PM interface, including the following +five power management functions for driver code: + +1. Set the maximum MPU wakeup latency:: + + (*pdata->set_max_mpu_wakeup_lat)(struct device *dev, unsigned long t) + +2. Set the maximum device wakeup latency:: + + (*pdata->set_max_dev_wakeup_lat)(struct device *dev, unsigned long t) + +3. Set the maximum system DMA transfer start latency (CORE pwrdm):: + + (*pdata->set_max_sdma_lat)(struct device *dev, long t) + +4. Set the minimum bus throughput needed by a device:: + + (*pdata->set_min_bus_tput)(struct device *dev, u8 agent_id, unsigned long r) + +5. Return the number of times the device has lost context:: + + (*pdata->get_dev_context_loss_count)(struct device *dev) + + +Further documentation for all OMAP PM interface functions can be +found in arch/arm/plat-omap/include/mach/omap-pm.h. + + +The OMAP PM layer is intended to be temporary +--------------------------------------------- + +The intention is that eventually the Linux PM QoS layer should support +the range of power management features present in OMAP3. As this +happens, existing drivers using the OMAP PM interface can be modified +to use the Linux PM QoS code; and the OMAP PM interface can disappear. + + +Driver usage of the OMAP PM functions +------------------------------------- + +As the 'pdata' in the above examples indicates, these functions are +exposed to drivers through function pointers in driver .platform_data +structures. The function pointers are initialized by the `board-*.c` +files to point to the corresponding OMAP PM functions: + +- set_max_dev_wakeup_lat will point to + omap_pm_set_max_dev_wakeup_lat(), etc. Other architectures which do + not support these functions should leave these function pointers set + to NULL. Drivers should use the following idiom:: + + if (pdata->set_max_dev_wakeup_lat) + (*pdata->set_max_dev_wakeup_lat)(dev, t); + +The most common usage of these functions will probably be to specify +the maximum time from when an interrupt occurs, to when the device +becomes accessible. To accomplish this, driver writers should use the +set_max_mpu_wakeup_lat() function to constrain the MPU wakeup +latency, and the set_max_dev_wakeup_lat() function to constrain the +device wakeup latency (from clk_enable() to accessibility). For +example:: + + /* Limit MPU wakeup latency */ + if (pdata->set_max_mpu_wakeup_lat) + (*pdata->set_max_mpu_wakeup_lat)(dev, tc); + + /* Limit device powerdomain wakeup latency */ + if (pdata->set_max_dev_wakeup_lat) + (*pdata->set_max_dev_wakeup_lat)(dev, td); + + /* total wakeup latency in this example: (tc + td) */ + +The PM parameters can be overwritten by calling the function again +with the new value. The settings can be removed by calling the +function with a t argument of -1 (except in the case of +set_max_bus_tput(), which should be called with an r argument of 0). + +The fifth function above, omap_pm_get_dev_context_loss_count(), +is intended as an optimization to allow drivers to determine whether the +device has lost its internal context. If context has been lost, the +driver must restore its internal context before proceeding. + + +Other specialized interface functions +------------------------------------- + +The five functions listed above are intended to be usable by any +device driver. DSPBridge and CPUFreq have a few special requirements. +DSPBridge expresses target DSP performance levels in terms of OPP IDs. +CPUFreq expresses target MPU performance levels in terms of MPU +frequency. The OMAP PM interface contains functions for these +specialized cases to convert that input information (OPPs/MPU +frequency) into the form that the underlying power management +implementation needs: + +6. `(*pdata->dsp_get_opp_table)(void)` + +7. `(*pdata->dsp_set_min_opp)(u8 opp_id)` + +8. `(*pdata->dsp_get_opp)(void)` + +9. `(*pdata->cpu_get_freq_table)(void)` + +10. `(*pdata->cpu_set_freq)(unsigned long f)` + +11. `(*pdata->cpu_get_freq)(void)` + +Customizing OPP for platform +============================ +Defining CONFIG_PM should enable OPP layer for the silicon +and the registration of OPP table should take place automatically. +However, in special cases, the default OPP table may need to be +tweaked, for e.g.: + + * enable default OPPs which are disabled by default, but which + could be enabled on a platform + * Disable an unsupported OPP on the platform + * Define and add a custom opp table entry + in these cases, the board file needs to do additional steps as follows: + +arch/arm/mach-omapx/board-xyz.c:: + + #include "pm.h" + .... + static void __init omap_xyz_init_irq(void) + { + .... + /* Initialize the default table */ + omapx_opp_init(); + /* Do customization to the defaults */ + .... + } + +NOTE: + omapx_opp_init will be omap3_opp_init or as required + based on the omap family. |