diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
-rw-r--r-- | Documentation/kernel-parameters.txt | 43 |
1 files changed, 20 insertions, 23 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 01ece1b9213e..b72e071a3e5b 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -199,11 +199,6 @@ and is between 256 and 4096 characters. It is defined in the file unusable. The "log_buf_len" parameter may be useful if you need to capture more output. - acpi_display_output= [HW,ACPI] - acpi_display_output=vendor - acpi_display_output=video - See above. - acpi_irq_balance [HW,ACPI] ACPI will balance active IRQs default in APIC mode @@ -403,6 +398,10 @@ and is between 256 and 4096 characters. It is defined in the file bttv.pll= See Documentation/video4linux/bttv/Insmod-options bttv.tuner= and Documentation/video4linux/bttv/CARDLIST + bulk_remove=off [PPC] This parameter disables the use of the pSeries + firmware feature for flushing multiple hpte entries + at a time. + c101= [NET] Moxa C101 synchronous serial card cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection. @@ -655,11 +654,6 @@ and is between 256 and 4096 characters. It is defined in the file dscc4.setup= [NET] - dynamic_printk Enables pr_debug()/dev_dbg() calls if - CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. - These can also be switched on/off via - <debugfs>/dynamic_printk/modules - earlycon= [KNL] Output early console device and options. uart[8250],io,<addr>[,options] uart[8250],mmio,<addr>[,options] @@ -884,6 +878,7 @@ and is between 256 and 4096 characters. It is defined in the file controller i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX controllers + i8042.notimeout [HW] Ignore timeout condition signalled by conroller i8042.reset [HW] Reset the controller during init and cleanup i8042.unlock [HW] Unlock (ignore) the keylock @@ -1490,6 +1485,10 @@ and is between 256 and 4096 characters. It is defined in the file mtdparts= [MTD] See drivers/mtd/cmdlinepart.c. + multitce=off [PPC] This parameter disables the use of the pSeries + firmware feature for updating multiple TCE entries + at a time. + onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock] @@ -1579,20 +1578,12 @@ and is between 256 and 4096 characters. It is defined in the file nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels Format: [panic,][num] - Valid num: 0,1,2 + Valid num: 0 0 - turn nmi_watchdog off - 1 - use the IO-APIC timer for the NMI watchdog - 2 - use the local APIC for the NMI watchdog using - a performance counter. Note: This will use one - performance counter and the local APIC's performance - vector. When panic is specified, panic when an NMI watchdog timeout occurs. This is useful when you use a panic=... timeout and need the box quickly up again. - Instead of 1 and 2 it is possible to use the following - symbolic names: lapic and ioapic - Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic netpoll.carrier_timeout= [NET] Specifies amount of time (in seconds) that @@ -1622,6 +1613,8 @@ and is between 256 and 4096 characters. It is defined in the file noapic [SMP,APIC] Tells the kernel to not make use of any IOAPICs that may be present in the system. + noautogroup Disable scheduler automatic task group creation. + nobats [PPC] Do not use BATs for mapping kernel lowmem on "Classic" PPC cores. @@ -1707,6 +1700,9 @@ and is between 256 and 4096 characters. It is defined in the file no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver + no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page + fault handling. + nolapic [X86-32,APIC] Do not enable or use the local APIC. nolapic_timer [X86-32,APIC] Do not use the local APIC timer. @@ -2467,12 +2463,13 @@ and is between 256 and 4096 characters. It is defined in the file to facilitate early boot debugging. See also Documentation/trace/events.txt - tsc= Disable clocksource-must-verify flag for TSC. + tsc= Disable clocksource stability checks for TSC. Format: <string> [x86] reliable: mark tsc clocksource as reliable, this - disables clocksource verification at runtime. - Used to enable high-resolution timer mode on older - hardware, and in virtualized environment. + disables clocksource verification at runtime, as well + as the stability checks done at bootup. Used to enable + high-resolution timer mode on older hardware, and in + virtualized environment. [x86] noirqtime: Do not use TSC to do irq accounting. Used to run time disable IRQ_TIME_ACCOUNTING on any platforms where RDTSC is slow and this accounting |