summaryrefslogtreecommitdiffstats
path: root/Documentation/spi
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/spi')
-rw-r--r--Documentation/spi/spi-lm70llp69
1 files changed, 69 insertions, 0 deletions
diff --git a/Documentation/spi/spi-lm70llp b/Documentation/spi/spi-lm70llp
new file mode 100644
index 000000000000..154bd02220b9
--- /dev/null
+++ b/Documentation/spi/spi-lm70llp
@@ -0,0 +1,69 @@
+spi_lm70llp : LM70-LLP parport-to-SPI adapter
+==============================================
+
+Supported board/chip:
+ * National Semiconductor LM70 LLP evaluation board
+ Datasheet: http://www.national.com/pf/LM/LM70.html
+
+Author:
+ Kaiwan N Billimoria <kaiwan@designergraphix.com>
+
+Description
+-----------
+This driver provides glue code connecting a National Semiconductor LM70 LLP
+temperature sensor evaluation board to the kernel's SPI core subsystem.
+
+In effect, this driver turns the parallel port interface on the eval board
+into a SPI bus with a single device, which will be driven by the generic
+LM70 driver (drivers/hwmon/lm70.c).
+
+The hardware interfacing on the LM70 LLP eval board is as follows:
+
+ Parallel LM70 LLP
+ Port Direction JP2 Header
+ ----------- --------- ----------------
+ D0 2 - -
+ D1 3 --> V+ 5
+ D2 4 --> V+ 5
+ D3 5 --> V+ 5
+ D4 6 --> V+ 5
+ D5 7 --> nCS 8
+ D6 8 --> SCLK 3
+ D7 9 --> SI/O 5
+ GND 25 - GND 7
+ Select 13 <-- SI/O 1
+ ----------- --------- ----------------
+
+Note that since the LM70 uses a "3-wire" variant of SPI, the SI/SO pin
+is connected to both pin D7 (as Master Out) and Select (as Master In)
+using an arrangment that lets either the parport or the LM70 pull the
+pin low. This can't be shared with true SPI devices, but other 3-wire
+devices might share the same SI/SO pin.
+
+The bitbanger routine in this driver (lm70_txrx) is called back from
+the bound "hwmon/lm70" protocol driver through its sysfs hook, using a
+spi_write_then_read() call. It performs Mode 0 (SPI/Microwire) bitbanging.
+The lm70 driver then inteprets the resulting digital temperature value
+and exports it through sysfs.
+
+A "gotcha": National Semiconductor's LM70 LLP eval board circuit schematic
+shows that the SI/O line from the LM70 chip is connected to the base of a
+transistor Q1 (and also a pullup, and a zener diode to D7); while the
+collector is tied to VCC.
+
+Interpreting this circuit, when the LM70 SI/O line is High (or tristate
+and not grounded by the host via D7), the transistor conducts and switches
+the collector to zero, which is reflected on pin 13 of the DB25 parport
+connector. When SI/O is Low (driven by the LM70 or the host) on the other
+hand, the transistor is cut off and the voltage tied to it's collector is
+reflected on pin 13 as a High level.
+
+So: the getmiso inline routine in this driver takes this fact into account,
+inverting the value read at pin 13.
+
+
+Thanks to
+---------
+o David Brownell for mentoring the SPI-side driver development.
+o Dr.Craig Hollabaugh for the (early) "manual" bitbanging driver version.
+o Nadir Billimoria for help interpreting the circuit schematic.