diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/DocBook/kgdb.tmpl | 20 | ||||
| -rw-r--r-- | Documentation/cpusets.txt | 2 | ||||
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 33 |
3 files changed, 20 insertions, 35 deletions
diff --git a/Documentation/DocBook/kgdb.tmpl b/Documentation/DocBook/kgdb.tmpl index 028a8444d95e..e8acd1f03456 100644 --- a/Documentation/DocBook/kgdb.tmpl +++ b/Documentation/DocBook/kgdb.tmpl @@ -84,10 +84,9 @@ runs an instance of gdb against the vmlinux file which contains the symbols (not boot image such as bzImage, zImage, uImage...). In gdb the developer specifies the connection parameters and - connects to kgdb. Depending on which kgdb I/O modules exist in - the kernel for a given architecture, it may be possible to debug - the test machine's kernel with the development machine using a - rs232 or ethernet connection. + connects to kgdb. The type of connection a developer makes with + gdb depends on the availability of kgdb I/O modules compiled as + builtin's or kernel modules in the test machine's kernel. </para> </chapter> <chapter id="CompilingAKernel"> @@ -223,7 +222,7 @@ </para> <para> IMPORTANT NOTE: Using this option with kgdb over the console - (kgdboc) or kgdb over ethernet (kgdboe) is not supported. + (kgdboc) is not supported. </para> </sect1> </chapter> @@ -249,18 +248,11 @@ (gdb) target remote /dev/ttyS0 </programlisting> <para> - Example (kgdb to a terminal server): + Example (kgdb to a terminal server on tcp port 2012): </para> <programlisting> % gdb ./vmlinux - (gdb) target remote udp:192.168.2.2:6443 - </programlisting> - <para> - Example (kgdb over ethernet): - </para> - <programlisting> - % gdb ./vmlinux - (gdb) target remote udp:192.168.2.2:6443 + (gdb) target remote 192.168.2.2:2012 </programlisting> <para> Once connected, you can debug a kernel the way you would debug an diff --git a/Documentation/cpusets.txt b/Documentation/cpusets.txt index d803c5c68ab5..353504de3084 100644 --- a/Documentation/cpusets.txt +++ b/Documentation/cpusets.txt @@ -542,7 +542,7 @@ otherwise initial value -1 that indicates the cpuset has no request. 2 : search cores in a package. 3 : search cpus in a node [= system wide on non-NUMA system] ( 4 : search nodes in a chunk of node [on NUMA system] ) - ( 5~ : search system wide [on NUMA system]) + ( 5 : search system wide [on NUMA system] ) This file is per-cpuset and affect the sched domain where the cpuset belongs to. Therefore if the flag 'sched_load_balance' of a cpuset diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index f4a8ebc1ef1a..2d845730d4e0 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -2,17 +2,12 @@ Naming and data format standards for sysfs files ------------------------------------------------ The libsensors library offers an interface to the raw sensors data -through the sysfs interface. See libsensors documentation and source for -further information. As of writing this document, libsensors -(from lm_sensors 2.8.3) is heavily chip-dependent. Adding or updating -support for any given chip requires modifying the library's code. -This is because libsensors was written for the procfs interface -older kernel modules were using, which wasn't standardized enough. -Recent versions of libsensors (from lm_sensors 2.8.2 and later) have -support for the sysfs interface, though. - -The new sysfs interface was designed to be as chip-independent as -possible. +through the sysfs interface. Since lm-sensors 3.0.0, libsensors is +completely chip-independent. It assumes that all the kernel drivers +implement the standard sysfs interface described in this document. +This makes adding or updating support for any given chip very easy, as +libsensors, and applications using it, do not need to be modified. +This is a major improvement compared to lm-sensors 2. Note that motherboards vary widely in the connections to sensor chips. There is no standard that ensures, for example, that the second @@ -35,19 +30,17 @@ access this data in a simple and consistent way. That said, such programs will have to implement conversion, labeling and hiding of inputs. For this reason, it is still not recommended to bypass the library. -If you are developing a userspace application please send us feedback on -this standard. - -Note that this standard isn't completely established yet, so it is subject -to changes. If you are writing a new hardware monitoring driver those -features can't seem to fit in this interface, please contact us with your -extension proposal. Keep in mind that backward compatibility must be -preserved. - Each chip gets its own directory in the sysfs /sys/devices tree. To find all sensor chips, it is easier to follow the device symlinks from /sys/class/hwmon/hwmon*. +Up to lm-sensors 3.0.0, libsensors looks for hardware monitoring attributes +in the "physical" device directory. Since lm-sensors 3.0.1, attributes found +in the hwmon "class" device directory are also supported. Complex drivers +(e.g. drivers for multifunction chips) may want to use this possibility to +avoid namespace pollution. The only drawback will be that older versions of +libsensors won't support the driver in question. + All sysfs values are fixed point numbers. There is only one value per file, unlike the older /proc specification. |