diff options
Diffstat (limited to 'Documentation')
8 files changed, 98 insertions, 1 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 0439c2aaf741..80c6fce9935b 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -497,7 +497,9 @@ Description: 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, + 125kohm_to_gnd: connected to ground via an 125kOhm resistor, 500kohm_to_gnd: connected to ground via a 500kOhm resistor, + 640kohm_to_gnd: connected to ground via a 640kOhm resistor, three_state: left floating. For a list of available output power down options read outX_powerdown_mode_available. If Y is not present the @@ -1491,3 +1493,10 @@ Description: This ABI is especially applicable for humidity sensors to heatup the device and get rid of any condensation in some humidity environment + +What: /sys/bus/iio/devices/iio:deviceX/in_ph_raw +KernelVersion: 4.5 +Contact: linux-iio@vger.kernel.org +Description: + Raw (unscaled no offset etc.) pH reading of a substance as a negative + base-10 logarithm of hydrodium ions in a litre of water. diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 3c10e8581144..165937e1ac1c 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -1,8 +1,10 @@ -Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer +Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC +triaxial accelerometer Required properties: - compatible: should contain one of + * "fsl,mma8451" * "fsl,mma8452" * "fsl,mma8453" * "fsl,mma8652" diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt new file mode 100644 index 000000000000..3223684a643b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt @@ -0,0 +1,28 @@ +* AT91 SAMA5D2 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "atmel,sama5d2-adc". + - reg: Should contain ADC registers location and length. + - interrupts: Should contain the IRQ line for the ADC. + - clocks: phandle to device clock. + - clock-names: Must be "adc_clk". + - vref-supply: Supply used as reference for conversions. + - vddana-supply: Supply for the adc device. + - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC. + - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC. + - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC. + +Example: + +adc: adc@fc030000 { + compatible = "atmel,sama5d2-adc"; + reg = <0xfc030000 0x100>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&adc_clk>; + clock-names = "adc_clk"; + atmel,min-sample-rate-hz = <200000>; + atmel,max-sample-rate-hz = <20000000>; + atmel,startup-time-ms = <4>; + vddana-supply = <&vdd_3v3_lp_reg>; + vref-supply = <&vdd_3v3_lp_reg>; +} diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt index dcae4ccfcc52..82bcce07255d 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt @@ -6,6 +6,7 @@ Required properties: "microchip,mcp3422" or "microchip,mcp3423" or "microchip,mcp3424" or + "microchip,mcp3425" or "microchip,mcp3426" or "microchip,mcp3427" or "microchip,mcp3428" diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt new file mode 100644 index 000000000000..cffa1907463a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific pH-SM OEM sensor + +http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,ph-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@65 { + compatible = "atlas,ph-sm"; + reg = <0x65>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt index f6fbac66ad06..295a9edfa4fd 100644 --- a/Documentation/devicetree/bindings/iio/health/max30100.txt +++ b/Documentation/devicetree/bindings/iio/health/max30100.txt @@ -11,11 +11,19 @@ Required properties: Refer to interrupt-controller/interrupts.txt for generic interrupt client node bindings. +Optional properties: + - maxim,led-current-microamp: configuration for LED current in microamperes + while the engine is running. First indexed value is the configuration for + the RED LED, and second value is for the IR LED. + + Refer to the datasheet for the allowed current values. + Example: max30100@057 { compatible = "maxim,max30100"; reg = <57>; + maxim,led-current-microamp = <24000 50000>; interrupt-parent = <&gpio1>; interrupts = <16 2>; }; diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt new file mode 100644 index 000000000000..eac30d508849 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/opt3001.txt @@ -0,0 +1,26 @@ +* Texas Instruments OPT3001 Ambient Light Sensor + +The driver supports interrupt-driven and interrupt-less operation, depending +on whether an interrupt property has been populated into the DT. Note that +the optional generation of IIO events on rising/falling light threshold changes +requires the use of interrupts. Without interrupts, only the simple reading +of the current light value is supported through the IIO API. + +http://www.ti.com/product/opt3001 + +Required properties: + - compatible: should be "ti,opt3001" + - reg: the I2C address of the sensor + +Optional properties: + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge) + +Example: + +opt3001@44 { + compatible = "ti,opt3001"; + reg = <0x44>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 72e2c5a2b327..44ddc980b085 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -28,6 +28,7 @@ arm ARM Ltd. armadeus ARMadeus Systems SARL artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. +atlas Atlas Scientific LLC atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies |