summaryrefslogtreecommitdiffstats
path: root/arch/sh/include/asm/hd64465/hd64465.h
diff options
context:
space:
mode:
Diffstat (limited to 'arch/sh/include/asm/hd64465/hd64465.h')
-rw-r--r--arch/sh/include/asm/hd64465/hd64465.h256
1 files changed, 0 insertions, 256 deletions
diff --git a/arch/sh/include/asm/hd64465/hd64465.h b/arch/sh/include/asm/hd64465/hd64465.h
deleted file mode 100644
index cfd0e803d2a2..000000000000
--- a/arch/sh/include/asm/hd64465/hd64465.h
+++ /dev/null
@@ -1,256 +0,0 @@
-#ifndef _ASM_SH_HD64465_
-#define _ASM_SH_HD64465_ 1
-/*
- * $Id: hd64465.h,v 1.3 2003/05/04 19:30:15 lethal Exp $
- *
- * Hitachi HD64465 companion chip support
- *
- * by Greg Banks <gbanks@pocketpenguins.com>
- * (c) 2000 PocketPenguins Inc.
- *
- * Derived from <asm/hd64461.h> which bore the message:
- * Copyright (C) 2000 YAEGASHI Takeshi
- */
-#include <asm/io.h>
-#include <asm/irq.h>
-
-/*
- * Note that registers are defined here as virtual port numbers,
- * which have no meaning except to get translated by hd64465_isa_port2addr()
- * to an address in the range 0xb0000000-0xb3ffffff. Note that
- * this translation happens to consist of adding the lower 16 bits
- * of the virtual port number to 0xb0000000. Note also that the manual
- * shows addresses as absolute physical addresses starting at 0x10000000,
- * so e.g. the NIRR register is listed as 0x15000 here, 0x10005000 in the
- * manual, and accessed using address 0xb0005000 - Greg.
- */
-
-/* System registers */
-#define HD64465_REG_SRR 0x1000c /* System Revision Register */
-#define HD64465_REG_SDID 0x10010 /* System Device ID Reg */
-#define HD64465_SDID 0x8122 /* 64465 device ID */
-
-/* Power Management registers */
-#define HD64465_REG_SMSCR 0x10000 /* System Module Standby Control Reg */
-#define HD64465_SMSCR_PS2ST 0x4000 /* PS/2 Standby */
-#define HD64465_SMSCR_ADCST 0x1000 /* ADC Standby */
-#define HD64465_SMSCR_UARTST 0x0800 /* UART Standby */
-#define HD64465_SMSCR_SCDIST 0x0200 /* Serial Codec Standby */
-#define HD64465_SMSCR_PPST 0x0100 /* Parallel Port Standby */
-#define HD64465_SMSCR_PC0ST 0x0040 /* PCMCIA0 Standby */
-#define HD64465_SMSCR_PC1ST 0x0020 /* PCMCIA1 Standby */
-#define HD64465_SMSCR_AFEST 0x0010 /* AFE Standby */
-#define HD64465_SMSCR_TM0ST 0x0008 /* Timer0 Standby */
-#define HD64465_SMSCR_TM1ST 0x0004 /* Timer1 Standby */
-#define HD64465_SMSCR_IRDAST 0x0002 /* IRDA Standby */
-#define HD64465_SMSCR_KBCST 0x0001 /* Keyboard Controller Standby */
-
-/* Interrupt Controller registers */
-#define HD64465_REG_NIRR 0x15000 /* Interrupt Request Register */
-#define HD64465_REG_NIMR 0x15002 /* Interrupt Mask Register */
-#define HD64465_REG_NITR 0x15004 /* Interrupt Trigger Mode Register */
-
-/* Timer registers */
-#define HD64465_REG_TCVR1 0x16000 /* Timer 1 constant value register */
-#define HD64465_REG_TCVR0 0x16002 /* Timer 0 constant value register */
-#define HD64465_REG_TRVR1 0x16004 /* Timer 1 read value register */
-#define HD64465_REG_TRVR0 0x16006 /* Timer 0 read value register */
-#define HD64465_REG_TCR1 0x16008 /* Timer 1 control register */
-#define HD64465_REG_TCR0 0x1600A /* Timer 0 control register */
-#define HD64465_TCR_EADT 0x10 /* Enable ADTRIG# signal */
-#define HD64465_TCR_ETMO 0x08 /* Enable TMO signal */
-#define HD64465_TCR_PST_MASK 0x06 /* Clock Prescale */
-#define HD64465_TCR_PST_1 0x06 /* 1:1 */
-#define HD64465_TCR_PST_4 0x04 /* 1:4 */
-#define HD64465_TCR_PST_8 0x02 /* 1:8 */
-#define HD64465_TCR_PST_16 0x00 /* 1:16 */
-#define HD64465_TCR_TSTP 0x01 /* Start/Stop timer */
-#define HD64465_REG_TIRR 0x1600C /* Timer interrupt request register */
-#define HD64465_REG_TIDR 0x1600E /* Timer interrupt disable register */
-#define HD64465_REG_PWM1CS 0x16010 /* PWM 1 clock scale register */
-#define HD64465_REG_PWM1LPC 0x16012 /* PWM 1 low pulse width counter register */
-#define HD64465_REG_PWM1HPC 0x16014 /* PWM 1 high pulse width counter register */
-#define HD64465_REG_PWM0CS 0x16018 /* PWM 0 clock scale register */
-#define HD64465_REG_PWM0LPC 0x1601A /* PWM 0 low pulse width counter register */
-#define HD64465_REG_PWM0HPC 0x1601C /* PWM 0 high pulse width counter register */
-
-/* Analog/Digital Converter registers */
-#define HD64465_REG_ADDRA 0x1E000 /* A/D data register A */
-#define HD64465_REG_ADDRB 0x1E002 /* A/D data register B */
-#define HD64465_REG_ADDRC 0x1E004 /* A/D data register C */
-#define HD64465_REG_ADDRD 0x1E006 /* A/D data register D */
-#define HD64465_REG_ADCSR 0x1E008 /* A/D control/status register */
-#define HD64465_ADCSR_ADF 0x80 /* A/D End Flag */
-#define HD64465_ADCSR_ADST 0x40 /* A/D Start Flag */
-#define HD64465_ADCSR_ADIS 0x20 /* A/D Interrupt Status */
-#define HD64465_ADCSR_TRGE 0x10 /* A/D Trigger Enable */
-#define HD64465_ADCSR_ADIE 0x08 /* A/D Interrupt Enable */
-#define HD64465_ADCSR_SCAN 0x04 /* A/D Scan Mode */
-#define HD64465_ADCSR_CH_MASK 0x03 /* A/D Channel */
-#define HD64465_REG_ADCALCR 0x1E00A /* A/D calibration sample control */
-#define HD64465_REG_ADCAL 0x1E00C /* A/D calibration data register */
-
-
-/* General Purpose I/O ports registers */
-#define HD64465_REG_GPACR 0x14000 /* Port A Control Register */
-#define HD64465_REG_GPBCR 0x14002 /* Port B Control Register */
-#define HD64465_REG_GPCCR 0x14004 /* Port C Control Register */
-#define HD64465_REG_GPDCR 0x14006 /* Port D Control Register */
-#define HD64465_REG_GPECR 0x14008 /* Port E Control Register */
-#define HD64465_REG_GPADR 0x14010 /* Port A Data Register */
-#define HD64465_REG_GPBDR 0x14012 /* Port B Data Register */
-#define HD64465_REG_GPCDR 0x14014 /* Port C Data Register */
-#define HD64465_REG_GPDDR 0x14016 /* Port D Data Register */
-#define HD64465_REG_GPEDR 0x14018 /* Port E Data Register */
-#define HD64465_REG_GPAICR 0x14020 /* Port A Interrupt Control Register */
-#define HD64465_REG_GPBICR 0x14022 /* Port B Interrupt Control Register */
-#define HD64465_REG_GPCICR 0x14024 /* Port C Interrupt Control Register */
-#define HD64465_REG_GPDICR 0x14026 /* Port D Interrupt Control Register */
-#define HD64465_REG_GPEICR 0x14028 /* Port E Interrupt Control Register */
-#define HD64465_REG_GPAISR 0x14040 /* Port A Interrupt Status Register */
-#define HD64465_REG_GPBISR 0x14042 /* Port B Interrupt Status Register */
-#define HD64465_REG_GPCISR 0x14044 /* Port C Interrupt Status Register */
-#define HD64465_REG_GPDISR 0x14046 /* Port D Interrupt Status Register */
-#define HD64465_REG_GPEISR 0x14048 /* Port E Interrupt Status Register */
-
-/* PCMCIA bridge interface */
-#define HD64465_REG_PCC0ISR 0x12000 /* socket 0 interface status */
-#define HD64465_PCCISR_PREADY 0x80 /* mem card ready / io card IREQ */
-#define HD64465_PCCISR_PIREQ 0x80
-#define HD64465_PCCISR_PMWP 0x40 /* mem card write-protected */
-#define HD64465_PCCISR_PVS2 0x20 /* voltage select pin 2 */
-#define HD64465_PCCISR_PVS1 0x10 /* voltage select pin 1 */
-#define HD64465_PCCISR_PCD_MASK 0x0c /* card detect */
-#define HD64465_PCCISR_PBVD_MASK 0x03 /* battery voltage */
-#define HD64465_PCCISR_PBVD_BATGOOD 0x03 /* battery good */
-#define HD64465_PCCISR_PBVD_BATWARN 0x01 /* battery low warning */
-#define HD64465_PCCISR_PBVD_BATDEAD1 0x02 /* battery dead */
-#define HD64465_PCCISR_PBVD_BATDEAD2 0x00 /* battery dead */
-#define HD64465_REG_PCC0GCR 0x12002 /* socket 0 general control */
-#define HD64465_PCCGCR_PDRV 0x80 /* output drive */
-#define HD64465_PCCGCR_PCCR 0x40 /* PC card reset */
-#define HD64465_PCCGCR_PCCT 0x20 /* PC card type, 1=IO&mem, 0=mem */
-#define HD64465_PCCGCR_PVCC0 0x10 /* voltage control pin VCC0SEL0 */
-#define HD64465_PCCGCR_PMMOD 0x08 /* memory mode */
-#define HD64465_PCCGCR_PPA25 0x04 /* pin A25 */
-#define HD64465_PCCGCR_PPA24 0x02 /* pin A24 */
-#define HD64465_PCCGCR_PREG 0x01 /* ping PCC0REG# */
-#define HD64465_REG_PCC0CSCR 0x12004 /* socket 0 card status change */
-#define HD64465_PCCCSCR_PSCDI 0x80 /* sw card detect intr */
-#define HD64465_PCCCSCR_PSWSEL 0x40 /* power select */
-#define HD64465_PCCCSCR_PIREQ 0x20 /* IREQ intr req */
-#define HD64465_PCCCSCR_PSC 0x10 /* STSCHG (status change) pin */
-#define HD64465_PCCCSCR_PCDC 0x08 /* CD (card detect) change */
-#define HD64465_PCCCSCR_PRC 0x04 /* ready change */
-#define HD64465_PCCCSCR_PBW 0x02 /* battery warning change */
-#define HD64465_PCCCSCR_PBD 0x01 /* battery dead change */
-#define HD64465_REG_PCC0CSCIER 0x12006 /* socket 0 card status change interrupt enable */
-#define HD64465_PCCCSCIER_PCRE 0x80 /* change reset enable */
-#define HD64465_PCCCSCIER_PIREQE_MASK 0x60 /* IREQ enable */
-#define HD64465_PCCCSCIER_PIREQE_DISABLED 0x00 /* IREQ disabled */
-#define HD64465_PCCCSCIER_PIREQE_LEVEL 0x20 /* IREQ level-triggered */
-#define HD64465_PCCCSCIER_PIREQE_FALLING 0x40 /* IREQ falling-edge-trig */
-#define HD64465_PCCCSCIER_PIREQE_RISING 0x60 /* IREQ rising-edge-trig */
-#define HD64465_PCCCSCIER_PSCE 0x10 /* status change enable */
-#define HD64465_PCCCSCIER_PCDE 0x08 /* card detect change enable */
-#define HD64465_PCCCSCIER_PRE 0x04 /* ready change enable */
-#define HD64465_PCCCSCIER_PBWE 0x02 /* battery warn change enable */
-#define HD64465_PCCCSCIER_PBDE 0x01 /* battery dead change enable*/
-#define HD64465_REG_PCC0SCR 0x12008 /* socket 0 software control */
-#define HD64465_PCCSCR_SHDN 0x10 /* TPS2206 SHutDowN pin */
-#define HD64465_PCCSCR_SWP 0x01 /* write protect */
-#define HD64465_REG_PCCPSR 0x1200A /* serial power switch control */
-#define HD64465_REG_PCC1ISR 0x12010 /* socket 1 interface status */
-#define HD64465_REG_PCC1GCR 0x12012 /* socket 1 general control */
-#define HD64465_REG_PCC1CSCR 0x12014 /* socket 1 card status change */
-#define HD64465_REG_PCC1CSCIER 0x12016 /* socket 1 card status change interrupt enable */
-#define HD64465_REG_PCC1SCR 0x12018 /* socket 1 software control */
-
-
-/* PS/2 Keyboard and mouse controller -- *not* register compatible */
-#define HD64465_REG_KBCSR 0x1dc00 /* Keyboard Control/Status reg */
-#define HD64465_KBCSR_KBCIE 0x8000 /* KBCK Input Enable */
-#define HD64465_KBCSR_KBCOE 0x4000 /* KBCK Output Enable */
-#define HD64465_KBCSR_KBDOE 0x2000 /* KB DATA Output Enable */
-#define HD64465_KBCSR_KBCD 0x1000 /* KBCK Driven */
-#define HD64465_KBCSR_KBDD 0x0800 /* KB DATA Driven */
-#define HD64465_KBCSR_KBCS 0x0400 /* KBCK pin Status */
-#define HD64465_KBCSR_KBDS 0x0200 /* KB DATA pin Status */
-#define HD64465_KBCSR_KBDP 0x0100 /* KB DATA Parity bit */
-#define HD64465_KBCSR_KBD_MASK 0x00ff /* KD DATA shift reg */
-#define HD64465_REG_KBISR 0x1dc04 /* Keyboard Interrupt Status reg */
-#define HD64465_KBISR_KBRDF 0x0001 /* KB Received Data Full */
-#define HD64465_REG_MSCSR 0x1dc10 /* Mouse Control/Status reg */
-#define HD64465_REG_MSISR 0x1dc14 /* Mouse Interrupt Status reg */
-
-
-/*
- * Logical address at which the HD64465 is mapped. Note that this
- * should always be in the P2 segment (uncached and untranslated).
- */
-#ifndef CONFIG_HD64465_IOBASE
-#define CONFIG_HD64465_IOBASE 0xb0000000
-#endif
-/*
- * The HD64465 multiplexes all its modules' interrupts onto
- * this single interrupt.
- */
-#ifndef CONFIG_HD64465_IRQ
-#define CONFIG_HD64465_IRQ 5
-#endif
-
-
-#define _HD64465_IO_MASK 0xf8000000
-#define is_hd64465_addr(addr) \
- ((addr & _HD64465_IO_MASK) == (CONFIG_HD64465_IOBASE & _HD64465_IO_MASK))
-
-/*
- * A range of 16 virtual interrupts generated by
- * demuxing the HD64465 muxed interrupt.
- */
-#define HD64465_IRQ_BASE OFFCHIP_IRQ_BASE
-#define HD64465_IRQ_NUM 16
-#define HD64465_IRQ_ADC (HD64465_IRQ_BASE+0)
-#define HD64465_IRQ_USB (HD64465_IRQ_BASE+1)
-#define HD64465_IRQ_SCDI (HD64465_IRQ_BASE+2)
-#define HD64465_IRQ_PARALLEL (HD64465_IRQ_BASE+3)
-/* bit 4 is reserved */
-#define HD64465_IRQ_UART (HD64465_IRQ_BASE+5)
-#define HD64465_IRQ_IRDA (HD64465_IRQ_BASE+6)
-#define HD64465_IRQ_PS2MOUSE (HD64465_IRQ_BASE+7)
-#define HD64465_IRQ_KBC (HD64465_IRQ_BASE+8)
-#define HD64465_IRQ_TIMER1 (HD64465_IRQ_BASE+9)
-#define HD64465_IRQ_TIMER0 (HD64465_IRQ_BASE+10)
-#define HD64465_IRQ_GPIO (HD64465_IRQ_BASE+11)
-#define HD64465_IRQ_AFE (HD64465_IRQ_BASE+12)
-#define HD64465_IRQ_PCMCIA1 (HD64465_IRQ_BASE+13)
-#define HD64465_IRQ_PCMCIA0 (HD64465_IRQ_BASE+14)
-#define HD64465_IRQ_PS2KBD (HD64465_IRQ_BASE+15)
-
-/* Constants for PCMCIA mappings */
-#define HD64465_PCC_WINDOW 0x01000000
-
-#define HD64465_PCC0_BASE 0xb8000000 /* area 6 */
-#define HD64465_PCC0_ATTR (HD64465_PCC0_BASE)
-#define HD64465_PCC0_COMM (HD64465_PCC0_BASE+HD64465_PCC_WINDOW)
-#define HD64465_PCC0_IO (HD64465_PCC0_BASE+2*HD64465_PCC_WINDOW)
-
-#define HD64465_PCC1_BASE 0xb4000000 /* area 5 */
-#define HD64465_PCC1_ATTR (HD64465_PCC1_BASE)
-#define HD64465_PCC1_COMM (HD64465_PCC1_BASE+HD64465_PCC_WINDOW)
-#define HD64465_PCC1_IO (HD64465_PCC1_BASE+2*HD64465_PCC_WINDOW)
-
-/*
- * Base of USB controller interface (as memory)
- */
-#define HD64465_USB_BASE (CONFIG_HD64465_IOBASE+0xb000)
-#define HD64465_USB_LEN 0x1000
-/*
- * Base of embedded SRAM, used for USB controller.
- */
-#define HD64465_SRAM_BASE (CONFIG_HD64465_IOBASE+0x9000)
-#define HD64465_SRAM_LEN 0x1000
-
-
-
-#endif /* _ASM_SH_HD64465_ */