diff options
Diffstat (limited to 'drivers/power/reset')
| -rw-r--r-- | drivers/power/reset/Kconfig | 1 | ||||
| -rw-r--r-- | drivers/power/reset/at91-reset.c | 4 | ||||
| -rw-r--r-- | drivers/power/reset/ltc2952-poweroff.c | 18 |
3 files changed, 6 insertions, 17 deletions
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig index aad9c3318c02..17d93a73c513 100644 --- a/drivers/power/reset/Kconfig +++ b/drivers/power/reset/Kconfig @@ -41,6 +41,7 @@ config POWER_RESET_AXXIA config POWER_RESET_BRCMSTB bool "Broadcom STB reset driver" depends on ARM || MIPS || COMPILE_TEST + depends on MFD_SYSCON default ARCH_BRCMSTB help This driver provides restart support for Broadcom STB boards. diff --git a/drivers/power/reset/at91-reset.c b/drivers/power/reset/at91-reset.c index 01c7055c4200..ca461ebc7ae8 100644 --- a/drivers/power/reset/at91-reset.c +++ b/drivers/power/reset/at91-reset.c @@ -212,9 +212,9 @@ static int at91_reset_platform_probe(struct platform_device *pdev) res = platform_get_resource(pdev, IORESOURCE_MEM, idx + 1 ); at91_ramc_base[idx] = devm_ioremap(&pdev->dev, res->start, resource_size(res)); - if (IS_ERR(at91_ramc_base[idx])) { + if (!at91_ramc_base[idx]) { dev_err(&pdev->dev, "Could not map ram controller address\n"); - return PTR_ERR(at91_ramc_base[idx]); + return -ENOMEM; } } diff --git a/drivers/power/reset/ltc2952-poweroff.c b/drivers/power/reset/ltc2952-poweroff.c index 7ef193b6f7fe..1e08195551fe 100644 --- a/drivers/power/reset/ltc2952-poweroff.c +++ b/drivers/power/reset/ltc2952-poweroff.c @@ -120,18 +120,7 @@ static enum hrtimer_restart ltc2952_poweroff_timer_wde(struct hrtimer *timer) static void ltc2952_poweroff_start_wde(struct ltc2952_poweroff *data) { - if (hrtimer_start(&data->timer_wde, data->wde_interval, - HRTIMER_MODE_REL)) { - /* - * The device will not toggle the watchdog reset, - * thus shut down is only safe if the PowerPath controller - * has a long enough time-off before triggering a hardware - * power-off. - * - * Only sending a warning as the system will power-off anyway - */ - dev_err(data->dev, "unable to start the timer\n"); - } + hrtimer_start(&data->timer_wde, data->wde_interval, HRTIMER_MODE_REL); } static enum hrtimer_restart @@ -165,9 +154,8 @@ static irqreturn_t ltc2952_poweroff_handler(int irq, void *dev_id) } if (gpiod_get_value(data->gpio_trigger)) { - if (hrtimer_start(&data->timer_trigger, data->trigger_delay, - HRTIMER_MODE_REL)) - dev_err(data->dev, "unable to start the wait timer\n"); + hrtimer_start(&data->timer_trigger, data->trigger_delay, + HRTIMER_MODE_REL); } else { hrtimer_cancel(&data->timer_trigger); /* omitting return value check, timer should have been valid */ |