diff options
Diffstat (limited to 'include/asm-m68k/mac_iop.h')
| -rw-r--r-- | include/asm-m68k/mac_iop.h | 162 |
1 files changed, 162 insertions, 0 deletions
diff --git a/include/asm-m68k/mac_iop.h b/include/asm-m68k/mac_iop.h new file mode 100644 index 000000000000..b0d2e3473537 --- /dev/null +++ b/include/asm-m68k/mac_iop.h @@ -0,0 +1,162 @@ +/* + * I/O Processor (IOP) defines and structures, mostly snagged from A/UX + * header files. + * + * The original header from which this was taken is copyrighted. I've done some + * rewriting (in fact my changes make this a bit more readable, IMHO) but some + * more should be done. + */ + +/* + * This is the base address of the IOPs. Use this as the address of + * a "struct iop" (see below) to see where the actual registers fall. + */ + +#define SCC_IOP_BASE_IIFX (0x50F04000) +#define ISM_IOP_BASE_IIFX (0x50F12000) + +#define SCC_IOP_BASE_QUADRA (0x50F0C000) +#define ISM_IOP_BASE_QUADRA (0x50F1E000) + +/* IOP status/control register bits: */ + +#define IOP_BYPASS 0x01 /* bypass-mode hardware access */ +#define IOP_AUTOINC 0x02 /* allow autoincrement of ramhi/lo */ +#define IOP_RUN 0x04 /* set to 0 to reset IOP chip */ +#define IOP_IRQ 0x08 /* generate IRQ to IOP if 1 */ +#define IOP_INT0 0x10 /* intr priority from IOP to host */ +#define IOP_INT1 0x20 /* intr priority from IOP to host */ +#define IOP_HWINT 0x40 /* IRQ from hardware; bypass mode only */ +#define IOP_DMAINACTIVE 0x80 /* no DMA request active; bypass mode only */ + +#define NUM_IOPS 2 +#define NUM_IOP_CHAN 7 +#define NUM_IOP_MSGS NUM_IOP_CHAN*8 +#define IOP_MSG_LEN 32 + +/* IOP reference numbers, used by the globally-visible iop_xxx functions */ + +#define IOP_NUM_SCC 0 +#define IOP_NUM_ISM 1 + +/* IOP channel states */ + +#define IOP_MSG_IDLE 0 /* idle */ +#define IOP_MSG_NEW 1 /* new message sent */ +#define IOP_MSG_RCVD 2 /* message received; processing */ +#define IOP_MSG_COMPLETE 3 /* message processing complete */ + +/* IOP message status codes */ + +#define IOP_MSGSTATUS_UNUSED 0 /* Unusued message structure */ +#define IOP_MSGSTATUS_WAITING 1 /* waiting for channel */ +#define IOP_MSGSTATUS_SENT 2 /* message sent, awaiting reply */ +#define IOP_MSGSTATUS_COMPLETE 3 /* message complete and reply rcvd */ +#define IOP_MSGSTATUS_UNSOL 6 /* message is unsolicited */ + +/* IOP memory addresses of the members of the mac_iop_kernel structure. */ + +#define IOP_ADDR_MAX_SEND_CHAN 0x0200 +#define IOP_ADDR_SEND_STATE 0x0201 +#define IOP_ADDR_PATCH_CTRL 0x021F +#define IOP_ADDR_SEND_MSG 0x0220 +#define IOP_ADDR_MAX_RECV_CHAN 0x0300 +#define IOP_ADDR_RECV_STATE 0x0301 +#define IOP_ADDR_ALIVE 0x031F +#define IOP_ADDR_RECV_MSG 0x0320 + +#ifndef __ASSEMBLY__ + +/* + * IOP Control registers, staggered because in usual Apple style they were + * too lazy to decode the A0 bit. This structure is assumed to begin at + * one of the xxx_IOP_BASE addresses given above. + */ + +struct mac_iop { + __u8 ram_addr_hi; /* shared RAM address hi byte */ + __u8 pad0; + __u8 ram_addr_lo; /* shared RAM address lo byte */ + __u8 pad1; + __u8 status_ctrl; /* status/control register */ + __u8 pad2[3]; + __u8 ram_data; /* RAM data byte at ramhi/lo */ + + __u8 pad3[23]; + + /* Bypass-mode hardware access registers */ + + union { + struct { /* SCC registers */ + __u8 sccb_cmd; /* SCC B command reg */ + __u8 pad4; + __u8 scca_cmd; /* SCC A command reg */ + __u8 pad5; + __u8 sccb_data; /* SCC B data */ + __u8 pad6; + __u8 scca_data; /* SCC A data */ + } scc_regs; + + struct { /* ISM registers */ + __u8 wdata; /* write a data byte */ + __u8 pad7; + __u8 wmark; /* write a mark byte */ + __u8 pad8; + __u8 wcrc; /* write 2-byte crc to disk */ + __u8 pad9; + __u8 wparams; /* write the param regs */ + __u8 pad10; + __u8 wphase; /* write the phase states & dirs */ + __u8 pad11; + __u8 wsetup; /* write the setup register */ + __u8 pad12; + __u8 wzeroes; /* mode reg: 1's clr bits, 0's are x */ + __u8 pad13; + __u8 wones; /* mode reg: 1's set bits, 0's are x */ + __u8 pad14; + __u8 rdata; /* read a data byte */ + __u8 pad15; + __u8 rmark; /* read a mark byte */ + __u8 pad16; + __u8 rerror; /* read the error register */ + __u8 pad17; + __u8 rparams; /* read the param regs */ + __u8 pad18; + __u8 rphase; /* read the phase states & dirs */ + __u8 pad19; + __u8 rsetup; /* read the setup register */ + __u8 pad20; + __u8 rmode; /* read the mode register */ + __u8 pad21; + __u8 rhandshake; /* read the handshake register */ + } ism_regs; + } b; +}; + +/* This structure is used to track IOP messages in the Linux kernel */ + +struct iop_msg { + struct iop_msg *next; /* next message in queue or NULL */ + uint iop_num; /* IOP number */ + uint channel; /* channel number */ + void *caller_priv; /* caller private data */ + int status; /* status of this message */ + __u8 message[IOP_MSG_LEN]; /* the message being sent/received */ + __u8 reply[IOP_MSG_LEN]; /* the reply to the message */ + void (*handler)(struct iop_msg *, struct pt_regs *); + /* function to call when reply recvd */ +}; + +extern int iop_scc_present,iop_ism_present; + +extern int iop_listen(uint, uint, + void (*handler)(struct iop_msg *, struct pt_regs *), + const char *); +extern int iop_send_message(uint, uint, void *, uint, __u8 *, + void (*)(struct iop_msg *, struct pt_regs *)); +extern void iop_complete_message(struct iop_msg *); +extern void iop_upload_code(uint, __u8 *, uint, __u16); +extern void iop_download_code(uint, __u8 *, uint, __u16); +extern __u8 *iop_compare_code(uint, __u8 *, uint, __u16); + +#endif /* __ASSEMBLY__ */ |