summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Linux 4.4.62v4.4.62Greg Kroah-Hartman2017-04-181-1/+1
|
* ibmveth: set correct gso_size and gso_typeThomas Falcon2017-04-182-2/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 7b5967389f5a8dfb9d32843830f5e2717e20995d upstream. This patch is based on an earlier one submitted by Jon Maxwell with the following commit message: "We recently encountered a bug where a few customers using ibmveth on the same LPAR hit an issue where a TCP session hung when large receive was enabled. Closer analysis revealed that the session was stuck because the one side was advertising a zero window repeatedly. We narrowed this down to the fact the ibmveth driver did not set gso_size which is translated by TCP into the MSS later up the stack. The MSS is used to calculate the TCP window size and as that was abnormally large, it was calculating a zero window, even although the sockets receive buffer was completely empty." We rely on the Virtual I/O Server partition in a pseries environment to provide the MSS through the TCP header checksum field. The stipulation is that users should not disable checksum offloading if rx packet aggregation is enabled through VIOS. Some firmware offerings provide the MSS in the RX buffer. This is signalled by a bit in the RX queue descriptor. Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com> Reviewed-by: David Dai <zdai@us.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx4_core: Fix when to save some qp context flags for dynamic VST to VGT ↵Jack Morgenstein2017-04-181-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | transitions commit 7c3945bc2073554bb2ecf983e073dee686679c53 upstream. Save the qp context flags byte containing the flag disabling vlan stripping in the RESET to INIT qp transition, rather than in the INIT to RTR transition. Per the firmware spec, the flags in this byte are active in the RESET to INIT transition. As a result of saving the flags in the incorrect qp transition, when switching dynamically from VGT to VST and back to VGT, the vlan remained stripped (as is required for VST) and did not return to not-stripped (as is required for VGT). Fixes: f0f829bf42cd ("net/mlx4_core: Add immediate activate for VGT->VST->VGT") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx4_core: Fix racy CQ (Completion Queue) freeJack Morgenstein2017-04-181-18/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 291c566a28910614ce42d0ffe82196eddd6346f4 upstream. In function mlx4_cq_completion() and mlx4_cq_event(), the radix_tree_lookup requires a rcu_read_lock. This is mandatory: if another core frees the CQ, it could run the radix_tree_node_rcu_free() call_rcu() callback while its being used by the radix tree lookup function. Additionally, in function mlx4_cq_event(), since we are adding the rcu lock around the radix-tree lookup, we no longer need to take the spinlock. Also, the synchronize_irq() call for the async event eliminates the need for incrementing the cq reference count in mlx4_cq_event(). Other changes: 1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock: we no longer take this spinlock in the interrupt context. The spinlock here, therefore, simply protects against different threads simultaneously invoking mlx4_cq_free() for different cq's. 2. In function mlx4_cq_free(), we move the radix tree delete to before the synchronize_irq() calls. This guarantees that we will not access this cq during any subsequent interrupts, and therefore can safely free the CQ after the synchronize_irq calls. The rcu_read_lock in the interrupt handlers only needs to protect against corrupting the radix tree; the interrupt handlers may access the cq outside the rcu_read_lock due to the synchronize_irq calls which protect against premature freeing of the cq. 3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg. 4. We leave the cq reference count mechanism in place, because it is still needed for the cq completion tasklet mechanism. Fixes: 6d90aa5cf17b ("net/mlx4_core: Make sure there are no pending async events when freeing CQ") Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx4_en: Fix bad WQE issueEugenia Emantayev2017-04-181-1/+7
| | | | | | | | | | | | | | | | commit 6496bbf0ec481966ef9ffe5b6660d8d1b55c60cc upstream. Single send WQE in RX buffer should be stamped with software ownership in order to prevent the flow of QP in error in FW once UPDATE_QP is called. Fixes: 9f519f68cfff ('mlx4_en: Not using Shared Receive Queues') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: hub: Wait for connection to be reestablished after port resetGuenter Roeck2017-04-181-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 22547c4cc4fe20698a6a85a55b8788859134b8e4 upstream. On a system with a defective USB device connected to an USB hub, an endless sequence of port connect events was observed. The sequence of events as observed is as follows: - Port reports connected event (port status=USB_PORT_STAT_CONNECTION). - Event handler debounces port and resets it by calling hub_port_reset(). - hub_port_reset() calls hub_port_wait_reset() to wait for the reset to complete. - The reset completes, but USB_PORT_STAT_CONNECTION is not immediately set in the port status register. - hub_port_wait_reset() returns -ENOTCONN. - Port initialization sequence is aborted. - A few milliseconds later, the port again reports a connected event, and the sequence repeats. This continues either forever or, randomly, stops if the connection is already re-established when the port status is read. It results in a high rate of udev events. This in turn destabilizes userspace since the above sequence holds the device mutex pretty much continuously and prevents userspace from actually reading the device status. To prevent the problem from happening, let's wait for the connection to be re-established after a port reset. If the device was actually disconnected, the code will still return an error, but it will do so only after the long reset timeout. Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* blk-mq: Avoid memory reclaim when remapping queuesGabriel Krisman Bertazi2017-04-181-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 36e1f3d107867b25c616c2fd294f5a1c9d4e5d09 upstream. While stressing memory and IO at the same time we changed SMT settings, we were able to consistently trigger deadlocks in the mm system, which froze the entire machine. I think that under memory stress conditions, the large allocations performed by blk_mq_init_rq_map may trigger a reclaim, which stalls waiting on the block layer remmaping completion, thus deadlocking the system. The trace below was collected after the machine stalled, waiting for the hotplug event completion. The simplest fix for this is to make allocations in this path non-reclaimable, with GFP_NOIO. With this patch, We couldn't hit the issue anymore. This should apply on top of Jens's for-next branch cleanly. Changes since v1: - Use GFP_NOIO instead of GFP_NOWAIT. Call Trace: [c000000f0160aaf0] [c000000f0160ab50] 0xc000000f0160ab50 (unreliable) [c000000f0160acc0] [c000000000016624] __switch_to+0x2e4/0x430 [c000000f0160ad20] [c000000000b1a880] __schedule+0x310/0x9b0 [c000000f0160ae00] [c000000000b1af68] schedule+0x48/0xc0 [c000000f0160ae30] [c000000000b1b4b0] schedule_preempt_disabled+0x20/0x30 [c000000f0160ae50] [c000000000b1d4fc] __mutex_lock_slowpath+0xec/0x1f0 [c000000f0160aed0] [c000000000b1d678] mutex_lock+0x78/0xa0 [c000000f0160af00] [d000000019413cac] xfs_reclaim_inodes_ag+0x33c/0x380 [xfs] [c000000f0160b0b0] [d000000019415164] xfs_reclaim_inodes_nr+0x54/0x70 [xfs] [c000000f0160b0f0] [d0000000194297f8] xfs_fs_free_cached_objects+0x38/0x60 [xfs] [c000000f0160b120] [c0000000003172c8] super_cache_scan+0x1f8/0x210 [c000000f0160b190] [c00000000026301c] shrink_slab.part.13+0x21c/0x4c0 [c000000f0160b2d0] [c000000000268088] shrink_zone+0x2d8/0x3c0 [c000000f0160b380] [c00000000026834c] do_try_to_free_pages+0x1dc/0x520 [c000000f0160b450] [c00000000026876c] try_to_free_pages+0xdc/0x250 [c000000f0160b4e0] [c000000000251978] __alloc_pages_nodemask+0x868/0x10d0 [c000000f0160b6f0] [c000000000567030] blk_mq_init_rq_map+0x160/0x380 [c000000f0160b7a0] [c00000000056758c] blk_mq_map_swqueue+0x33c/0x360 [c000000f0160b820] [c000000000567904] blk_mq_queue_reinit+0x64/0xb0 [c000000f0160b850] [c00000000056a16c] blk_mq_queue_reinit_notify+0x19c/0x250 [c000000f0160b8a0] [c0000000000f5d38] notifier_call_chain+0x98/0x100 [c000000f0160b8f0] [c0000000000c5fb0] __cpu_notify+0x70/0xe0 [c000000f0160b930] [c0000000000c63c4] notify_prepare+0x44/0xb0 [c000000f0160b9b0] [c0000000000c52f4] cpuhp_invoke_callback+0x84/0x250 [c000000f0160ba10] [c0000000000c570c] cpuhp_up_callbacks+0x5c/0x120 [c000000f0160ba60] [c0000000000c7cb8] _cpu_up+0xf8/0x1d0 [c000000f0160bac0] [c0000000000c7eb0] do_cpu_up+0x120/0x150 [c000000f0160bb40] [c0000000006fe024] cpu_subsys_online+0x64/0xe0 [c000000f0160bb90] [c0000000006f5124] device_online+0xb4/0x120 [c000000f0160bbd0] [c0000000006f5244] online_store+0xb4/0xc0 [c000000f0160bc20] [c0000000006f0a68] dev_attr_store+0x68/0xa0 [c000000f0160bc60] [c0000000003ccc30] sysfs_kf_write+0x80/0xb0 [c000000f0160bca0] [c0000000003cbabc] kernfs_fop_write+0x17c/0x250 [c000000f0160bcf0] [c00000000030fe6c] __vfs_write+0x6c/0x1e0 [c000000f0160bd90] [c000000000311490] vfs_write+0xd0/0x270 [c000000f0160bde0] [c0000000003131fc] SyS_write+0x6c/0x110 [c000000f0160be30] [c000000000009204] system_call+0x38/0xec Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Cc: Brian King <brking@linux.vnet.ibm.com> Cc: Douglas Miller <dougmill@linux.vnet.ibm.com> Cc: linux-block@vger.kernel.org Cc: linux-scsi@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/packet: fix overflow in check for priv area sizeAndrey Konovalov2017-04-181-2/+2
| | | | | | | | | | | | | | | | | | | commit 2b6867c2ce76c596676bec7d2d525af525fdc6e2 upstream. Subtracting tp_sizeof_priv from tp_block_size and casting to int to check whether one is less then the other doesn't always work (both of them are unsigned ints). Compare them as is instead. Also cast tp_sizeof_priv to u64 before using BLK_PLUS_PRIV, as it can overflow inside BLK_PLUS_PRIV otherwise. Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* crypto: caam - fix RNG deinstantiation error checkingHoria Geantă2017-04-181-1/+2
| | | | | | | | | | | | | | | | | | commit 40c98cb57cdbc377456116ad4582c89e329721b0 upstream. RNG instantiation was previously fixed by commit 62743a4145bb9 ("crypto: caam - fix RNG init descriptor ret. code checking") while deinstantiation was not addressed. Since the descriptors used are similar, in the sense that they both end with a JUMP HALT command, checking for errors should be similar too, i.e. status code 7000_0000h should be considered successful. Fixes: 1005bccd7a4a6 ("crypto: caam - enable instantiation of all RNG4 state handles") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatchMatt Redfearn2017-04-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | commit c25f8064c1d5731a2ce5664def890140dcdd3e5c upstream. Commit dda45f701c9d ("MIPS: Switch to the irq_stack in interrupts") changed both the normal and vectored interrupt handlers. Unfortunately the vectored version, "except_vec_vi_handler", was incorrectly modified to unconditionally jal to plat_irq_dispatch, rather than doing a jalr to the vectored handler that has been set up. This is ok for many platforms which set the vectored handler to plat_irq_dispatch anyway, but will cause problems with platforms that use other handlers. Fixes: dda45f701c9d ("MIPS: Switch to the irq_stack in interrupts") Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15110/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Select HAVE_IRQ_EXIT_ON_IRQ_STACKMatt Redfearn2017-04-181-0/+1
| | | | | | | | | | | | | | | | | | | commit 3cc3434fd6307d06b53b98ce83e76bf9807689b9 upstream. Since do_IRQ is now invoked on a separate IRQ stack, we select HAVE_IRQ_EXIT_ON_IRQ_STACK so that softirq's may be invoked directly from irq_exit(), rather than requiring do_softirq_own_stack. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14744/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Switch to the irq_stack in interruptsMatt Redfearn2017-04-181-5/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit dda45f701c9d7ad4ac0bb446e3a96f6df9a468d9 upstream. When enterring interrupt context via handle_int or except_vec_vi, switch to the irq_stack of the current CPU if it is not already in use. The current stack pointer is masked with the thread size and compared to the base or the irq stack. If it does not match then the stack pointer is set to the top of that stack, otherwise this is a nested irq being handled on the irq stack so the stack pointer should be left as it was. The in-use stack pointer is placed in the callee saved register s1. It will be saved to the stack when plat_irq_dispatch is invoked and can be restored once control returns here. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14743/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Only change $28 to thread_info if coming from user modeMatt Redfearn2017-04-181-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 510d86362a27577f5ee23f46cfb354ad49731e61 upstream. The SAVE_SOME macro is used to save the execution context on all exceptions. If an exception occurs while executing user code, the stack is switched to the kernel's stack for the current task, and register $28 is switched to point to the current_thread_info, which is at the bottom of the stack region. If the exception occurs while executing kernel code, the stack is left, and this change ensures that register $28 is not updated. This is the correct behaviour when the kernel can be executing on the separate irq stack, because the thread_info will not be at the base of it. With this change, register $28 is only switched to it's kernel conventional usage of the currrent thread info pointer at the point at which execution enters kernel space. Doing it on every exception was redundant, but OK without an IRQ stack, but will be erroneous once that is introduced. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14742/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Stack unwinding while on IRQ stackMatt Redfearn2017-04-181-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit d42d8d106b0275b027c1e8992c42aecf933436ea upstream. Within unwind stack, check if the stack pointer being unwound is within the CPU's irq_stack and if so use that page rather than the task's stack page. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14741/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Introduce irq_stackMatt Redfearn2017-04-183-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit fe8bd18ffea5327344d4ec2bf11f47951212abd0 upstream. Allocate a per-cpu irq stack for use within interrupt handlers. Also add a utility function on_irq_stack to determine if a given stack pointer is within the irq stack for that cpu. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Petr Mladek <pmladek@suse.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14740/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mtd: bcm47xxpart: fix parsing first block after aligned TRXRafał Miłecki2017-04-181-6/+4
| | | | | | | | | | | | | | | | | commit bd5d21310133921021d78995ad6346f908483124 upstream. After parsing TRX we should skip to the first block placed behind it. Our code was working only with TRX with length not aligned to the blocksize. In other cases (length aligned) it was missing the block places right after TRX. This fixes calculation and simplifies the comment. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: gadget: delay unmap of bounced requestsJanusz Dziedzic2017-04-181-4/+17
| | | | | | | | | | | | | | | commit de288e36fe33f7e06fa272bc8e2f85aa386d99aa upstream. In the case of bounced ep0 requests, we must delay DMA operation until after ->complete() otherwise we might overwrite contents of req->buf. This caused problems with RNDIS gadget. Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/i915: Stop using RP_DOWN_EI on BaytrailChris Wilson2017-04-183-48/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8f68d591d4765b2e1ce9d916ac7bc5583285c4ad upstream. On Baytrail, we manually calculate busyness over the evaluation interval to avoid issues with miscaluations with RC6 enabled. However, it turns out that the DOWN_EI interrupt generator is completely bust - it operates in two modes, continuous or never. Neither of which are conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just compute everything from the UP_EI which does seem to correspond to the desired interval. v2: Fixup gen6_rps_pm_mask() as well v3: Inline vlv_c0_above() to combine the now identical elapsed calculation for up/down and simplify the threshold testing Fixes: 43cf3bf084ba ("drm/i915: Improved w/a for rps on Baytrail") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170313170617.31564-1-chris@chris-wilson.co.uk (cherry picked from commit e0e8c7cb6eb68e9256de2d8cbeb481d3701c05ac) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/i915: Avoid tweaking evaluation thresholds on Baytrail v3Mika Kuoppala2017-04-181-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 34dc8993eef63681b062871413a9484008a2a78f upstream. Certain Baytrails, namely the 4 cpu core variants, have been plaqued by spurious system hangs, mostly occurring with light loads. Multiple bisects by various people point to a commit which changes the reclocking strategy for Baytrail to follow its bigger brethen: commit 8fb55197e64d ("drm/i915: Agressive downclocking on Baytrail") There is also a review comment attached to this commit from Deepak S on avoiding punit access on Cherryview and thus it was excluded on common reclocking path. By taking the same approach and omitting the punit access by not tweaking the thresholds when the hardware has been asked to move into different frequency, considerable gains in stability have been observed. With J1900 box, light render/video load would end up in system hang in usually less than 12 hours. With this patch applied, the cumulative uptime has now been 34 days without issues. To provoke system hang, light loads on both render and bsd engines in parallel have been used: glxgears >/dev/null 2>/dev/null & mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4 So far, author has not witnessed system hang with above load and this patch applied. Reports from the tenacious people at kernel bugzilla are also promising. Considering that the punit access frequency with this patch is considerably less, there is a possibility that this will push the, still unknown, root cause past the triggering point on most loads. But as we now can reliably reproduce the hang independently, we can reduce the pain that users are having and use a static thresholds until a root cause is found. v3: don't break debugfs and simplification (Chris Wilson) References: https://bugzilla.kernel.org/show_bug.cgi?id=109051 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Cc: fritsch@xbmc.org Cc: miku@iki.fi Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> CC: Michal Feix <michal@feix.cz> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Deepak S <deepak.s@linux.intel.com> Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com (cherry picked from commit 6067a27d1f0184596d51decbac1c1fdc4acb012f) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Linux 4.4.61v4.4.61Greg Kroah-Hartman2017-04-121-1/+1
|
* mm/mempolicy.c: fix error handling in set_mempolicy and mbind.Chris Salls2017-04-121-12/+8
| | | | | | | | | | | | | commit cf01fb9985e8deb25ccf0ea54d916b8871ae0e62 upstream. In the case that compat_get_bitmap fails we do not want to copy the bitmap to the user as it will contain uninitialized stack data and leak sensitive data. Signed-off-by: Chris Salls <salls@cs.ucsb.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Flush wrong invalid FTLB entry for huge pageHuacai Chen2017-04-121-4/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 0115f6cbf26663c86496bc56eeea293f85b77897 upstream. On VTLB+FTLB platforms (such as Loongson-3A R2), FTLB's pagesize is usually configured the same as PAGE_SIZE. In such a case, Huge page entry is not suitable to write in FTLB. Unfortunately, when a huge page is created, its page table entries haven't created immediately. Then the TLB refill handler will fetch an invalid page table entry which has no "HUGE" bit, and this entry may be written to FTLB. Since it is invalid, TLB load/store handler will then use tlbwi to write the valid entry at the same place. However, the valid entry is a huge page entry which isn't suitable for FTLB. Our solution is to modify build_huge_handler_tail. Flush the invalid old entry (whether it is in FTLB or VTLB, this is in order to reduce branches) and use tlbwr to write the valid new entry. Signed-off-by: Rui Wang <wangr@lemote.com> Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15754/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Lantiq: fix missing xbar kernel panicHauke Mehrtens2017-04-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 6ef90877eee63a0d03e83183bb44b64229b624e6 upstream. Commit 08b3c894e565 ("MIPS: lantiq: Disable xbar fpi burst mode") accidentally requested the resources from the pmu address region instead of the xbar registers region, but the check for the return value of request_mem_region() was wrong. Commit 98ea51cb0c8c ("MIPS: Lantiq: Fix another request_mem_region() return code check") fixed the check of the return value of request_mem_region() which made the kernel panics. This patch now makes use of the correct memory region for the cross bar. Fixes: 08b3c894e565 ("MIPS: lantiq: Disable xbar fpi burst mode") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org> Cc: james.hogan@imgtec.com Cc: arnd@arndb.de Cc: sergei.shtylyov@cogentembedded.com Cc: john@phrozen.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15751 Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: End spinlocks with .insnPaul Burton2017-04-121-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 4b5347a24a0f2d3272032c120664b484478455de upstream. When building for microMIPS we need to ensure that the assembler always knows that there is code at the target of a branch or jump. Recent toolchains will fail to link a microMIPS kernel when this isn't the case due to what it thinks is a branch to non-microMIPS code. mips-mti-linux-gnu-ld kernel/built-in.o: .spinlock.text+0x2fc: Unsupported branch between ISA modes. mips-mti-linux-gnu-ld final link failed: Bad value This is due to inline assembly labels in spinlock.h not being followed by an instruction mnemonic, either due to a .subsection pseudo-op or the end of the inline asm block. Fix this with a .insn direction after such labels. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/15325/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: ralink: Fix typos in rt3883 pinctrlJohn Crispin2017-04-121-2/+2
| | | | | | | | | | | | | | | | commit 7c5a3d813050ee235817b0220dd8c42359a9efd8 upstream. There are two copy & paste errors in the definition of the 5GHz LNA and second ethernet pinmux. Fixes: f576fb6a0700 ("MIPS: ralink: cleanup the soc specific pinmux data") Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15328/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* MIPS: Force o32 fp64 support on 32bit MIPS64r6 kernelsJames Hogan2017-04-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2e6c7747730296a6d4fd700894286db1132598c4 upstream. When a 32-bit kernel is configured to support MIPS64r6 (CPU_MIPS64_R6), MIPS_O32_FP64_SUPPORT won't be selected as it should be because MIPS32_O32 is disabled (o32 is already the default ABI available on 32-bit kernels). This results in userland FP breakage as CP0_Status.FR is read-only 1 since r6 (when an FPU is present) so __enable_fpu() will fail to clear FR. This causes the FPU emulator to get used which will incorrectly emulate 32-bit FPU registers. Force o32 fp64 support in this case by also selecting MIPS_O32_FP64_SUPPORT from CPU_MIPS64_R6 if 32BIT. Fixes: 4e9d324d4288 ("MIPS: Require O32 FP64 support for MIPS64 with O32 compat") Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15310/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/uaccess: get_user() should zero on failure (again)Heiko Carstens2017-04-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | commit d09c5373e8e4eaaa09233552cbf75dc4c4f21203 upstream. Commit fd2d2b191fe7 ("s390: get_user() should zero on failure") intended to fix s390's get_user() implementation which did not zero the target operand if the read from user space faulted. Unfortunately the patch has no effect: the corresponding inline assembly specifies that the operand is only written to ("=") and the previous value is discarded. Therefore the compiler is free to and actually does omit the zero initialization. To fix this simply change the contraint modifier to "+", so the compiler cannot omit the initialization anymore. Fixes: c9ca78415ac1 ("s390/uaccess: provide inline variants of get_user/put_user") Fixes: fd2d2b191fe7 ("s390: get_user() should zero on failure") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/decompressor: fix initrd corruption caused by bss clearMarcelo Henrique Cerri2017-04-121-16/+19
| | | | | | | | | | | | | | | | | | | | | | | | commit d82c0d12c92705ef468683c9b7a8298dd61ed191 upstream. Reorder the operations in decompress_kernel() to ensure initrd is moved to a safe location before the bss section is zeroed. During decompression bss can overlap with the initrd and this can corrupt the initrd contents depending on the size of the compressed kernel (which affects where the initrd is placed by the bootloader) and the size of the bss section of the decompressor. Also use the correct initrd size when checking for overlaps with parmblock. Fixes: 06c0dd72aea3 ([S390] fix boot failures with compressed kernels) Reviewed-by: Joy Latten <joy.latten@canonical.com> Reviewed-by: Vineetha HariPai <vineetha.hari.pai@canonical.com> Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nios2: reserve boot memory for device treeTobias Klauser2017-04-122-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 921d701e6f31e1ffaca3560416af1aa04edb4c4f upstream. Make sure to reserve the boot memory for the flattened device tree. Otherwise it might get overwritten, e.g. when initial_boot_params is copied, leading to a corrupted FDT and a boot hang/crash: bootconsole [early0] enabled Early console on uart16650 initialized at 0xf8001600 OF: fdt: Error -11 processing FDT Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree! ---[ end Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree! Guenter Roeck says: > I think I found the problem. In unflatten_and_copy_device_tree(), with added > debug information: > > OF: fdt: initial_boot_params=c861e400, dt=c861f000 size=28874 (0x70ca) > > ... and then initial_boot_params is copied to dt, which results in corrupted > fdt since the memory overlaps. Looks like the initial_boot_params memory > is not reserved and (re-)allocated by early_init_dt_alloc_memory_arch(). Reported-by: Guenter Roeck <linux@roeck-us.net> Reference: http://lkml.kernel.org/r/20170226210338.GA19476@roeck-us.net Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Ley Foon Tan <ley.foon.tan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* powerpc: Don't try to fix up misaligned load-with-reservation instructionsPaul Mackerras2017-04-121-8/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 48fe9e9488743eec9b7c1addd3c93f12f2123d54 upstream. In the past, there was only one load-with-reservation instruction, lwarx, and if a program attempted a lwarx on a misaligned address, it would take an alignment interrupt and the kernel handler would emulate it as though it was lwzx, which was not really correct, but benign since it is loading the right amount of data, and the lwarx should be paired with a stwcx. to the same address, which would also cause an alignment interrupt which would result in a SIGBUS being delivered to the process. We now have 5 different sizes of load-with-reservation instruction. Of those, lharx and ldarx cause an immediate SIGBUS by luck since their entries in aligninfo[] overlap instructions which were not fixed up, but lqarx overlaps with lhz and will be emulated as such. lbarx can never generate an alignment interrupt since it only operates on 1 byte. To straighten this out and fix the lqarx case, this adds code to detect the l[hwdq]arx instructions and return without fixing them up, resulting in a SIGBUS being delivered to the process. Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* powerpc/mm: Add missing global TLB invalidate if cxl is activeFrederic Barrat2017-04-121-2/+5
| | | | | | | | | | | | | | | | | | | | | commit 88b1bf7268f56887ca88eb09c6fb0f4fc970121a upstream. Commit 4c6d9acce1f4 ("powerpc/mm: Add hooks for cxl") converted local TLB invalidates to global if the cxl driver is active. This is necessary because the CAPP snoops invalidations to forward them to the PSL on the cxl adapter. However one path was forgotten. native_flush_hash_range() still does local TLB invalidates, as found out the hard way recently. This patch fixes it by following the same logic as previously: if the cxl driver is active, the local TLB invalidates are 'upgraded' to global. Fixes: 4c6d9acce1f4 ("powerpc/mm: Add hooks for cxl") Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Add missing fixupsJames Hogan2017-04-121-24/+48
| | | | | | | | | | | | | | | | | commit b884a190afcecdbef34ca508ea5ee88bb7c77861 upstream. The rapf copy loops in the Meta usercopy code is missing some extable entries for HTP cores with unaligned access checking enabled, where faults occur on the instruction immediately after the faulting access. Add the fixup labels and extable entries for these cases so that corner case user copy failures don't cause kernel crashes. Fixes: 373cd784d0fc ("metag: Memory handling") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Fix src fixup in from user rapf loopsJames Hogan2017-04-121-8/+28
| | | | | | | | | | | | | | | | | | | | | commit 2c0b1df88b987a12d95ea1d6beaf01894f3cc725 upstream. The fixup code to rewind the source pointer in __asm_copy_from_user_{32,64}bit_rapf_loop() always rewound the source by a single unit (4 or 8 bytes), however this is insufficient if the fault didn't occur on the first load in the loop, as the source pointer will have been incremented but nothing will have been stored until all 4 register [pairs] are loaded. Read the LSM_STEP field of TXSTATUS (which is already loaded into a register), a bit like the copy_to_user versions, to determine how many iterations of MGET[DL] have taken place, all of which need rewinding. Fixes: 373cd784d0fc ("metag: Memory handling") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Set flags before ADDZJames Hogan2017-04-121-4/+4
| | | | | | | | | | | | | | | | | | | | | commit fd40eee1290ad7add7aa665e3ce6b0f9fe9734b4 upstream. The fixup code for the copy_to_user rapf loops reads TXStatus.LSM_STEP to decide how far to rewind the source pointer. There is a special case for the last execution of an MGETL/MGETD, since it leaves LSM_STEP=0 even though the number of MGETLs/MGETDs attempted was 4. This uses ADDZ which is conditional upon the Z condition flag, but the AND instruction which masked the TXStatus.LSM_STEP field didn't set the condition flags based on the result. Fix that now by using ANDS which does set the flags, and also marking the condition codes as clobbered by the inline assembly. Fixes: 373cd784d0fc ("metag: Memory handling") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Zero rest of buffer from copy_from_userJames Hogan2017-04-122-46/+26
| | | | | | | | | | | | | | | | | | | | | | | | | commit 563ddc1076109f2b3f88e6d355eab7b6fd4662cb upstream. Currently we try to zero the destination for a failed read from userland in fixup code in the usercopy.c macros. The rest of the destination buffer is then zeroed from __copy_user_zeroing(), which is used for both copy_from_user() and __copy_from_user(). Unfortunately we fail to zero in the fixup code as D1Ar1 is set to 0 before the fixup code entry labels, and __copy_from_user() shouldn't even be zeroing the rest of the buffer. Move the zeroing out into copy_from_user() and rename __copy_user_zeroing() to raw_copy_from_user() since it no longer does any zeroing. This also conveniently matches the name needed for RAW_COPY_USER support in a later patch. Fixes: 373cd784d0fc ("metag: Memory handling") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Add early abort to copy_to_userJames Hogan2017-04-121-0/+20
| | | | | | | | | | | | | | | | commit fb8ea062a8f2e85256e13f55696c5c5f0dfdcc8b upstream. When copying to userland on Meta, if any faults are encountered immediately abort the copy instead of continuing on and repeatedly faulting, and worse potentially copying further bytes successfully to subsequent valid pages. Fixes: 373cd784d0fc ("metag: Memory handling") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Fix alignment error checkingJames Hogan2017-04-121-6/+4
| | | | | | | | | | | | | | | | | | | | commit 2257211942bbbf6c798ab70b487d7e62f7835a1a upstream. Fix the error checking of the alignment adjustment code in raw_copy_from_user(), which mistakenly considers it safe to skip the error check when aligning the source buffer on a 2 or 4 byte boundary. If the destination buffer was unaligned it may have started to copy using byte or word accesses, which could well be at the start of a new (valid) source page. This would result in it appearing to have copied 1 or 2 bytes at the end of the first (invalid) page rather than none at all. Fixes: 373cd784d0fc ("metag: Memory handling") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* metag/usercopy: Drop unused macrosJames Hogan2017-04-121-113/+0
| | | | | | | | | | | | | | commit ef62a2d81f73d9cddef14bc3d9097a57010d551c upstream. Metag's lib/usercopy.c has a bunch of copy_from_user macros for larger copies between 5 and 16 bytes which are completely unused. Before fixing zeroing lets drop these macros so there is less to fix. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ring-buffer: Fix return value check in test_ringbuffer()Wei Yongjun2017-04-121-4/+4
| | | | | | | | | | | | | | | | commit 62277de758b155dc04b78f195a1cb5208c37b2df upstream. In case of error, the function kthread_run() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Link: http://lkml.kernel.org/r/1466184839-14927-1-git-send-email-weiyj_lk@163.com Fixes: 6c43e554a ("ring-buffer: Add ring buffer startup selftest") Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ptrace: fix PTRACE_LISTEN race corrupting task->statebsegall@google.com2017-04-121-4/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5402e97af667e35e54177af8f6575518bf251d51 upstream. In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against __TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end of a PTRACE_LISTEN, this can wake the task /after/ the check against __TASK_TRACED, but before the reset of state to TASK_TRACED. This causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup against TRACED while the task is still on the rq wake_list, corrupting it. Oleg said: "The kernel can crash or this can lead to other hard-to-debug problems. In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced() assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the contract. Obviusly it is very wrong to manipulate task->state if this task is already running, or WAKING, or it sleeps again" [akpm@linux-foundation.org: coding-style fixes] Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL") Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com Signed-off-by: Ben Segall <bsegall@google.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Reset TreeId to zero on SMB2 TREE_CONNECTJan-Marek Glogowski2017-04-121-0/+4
| | | | | | | | | | | | | | | | | commit 806a28efe9b78ffae5e2757e1ee924b8e50c08ab upstream. Currently the cifs module breaks the CIFS specs on reconnect as described in http://msdn.microsoft.com/en-us/library/cc246529.aspx: "TreeId (4 bytes): Uniquely identifies the tree connect for the command. This MUST be 0 for the SMB2 TREE_CONNECT Request." Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Tested-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iio: bmg160: reset chip when probingQuentin Schulz2017-04-121-0/+12
| | | | | | | | | | | | | | | | | | | | commit 4bdc9029685ac03be50b320b29691766d2326c2b upstream. The gyroscope chip might need to be reset to be used. Without the chip being reset, the driver stopped at the first regmap_read (to get the CHIP_ID) and failed to probe. The datasheet of the gyroscope says that a minimum wait of 30ms after the reset has to be done. This patch has been checked on a BMX055 and the datasheet of the BMG160 and the BMI055 give the same reset register and bits. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* arm/arm64: KVM: Take mmap_sem in kvm_arch_prepare_memory_regionMarc Zyngier2017-04-121-3/+8
| | | | | | | | | | | | | | | | | commit 72f310481a08db821b614e7b5d00febcc9064b36 upstream. We don't hold the mmap_sem while searching for VMAs (via find_vma), in kvm_arch_prepare_memory_region, which can end up in expected failures. Fixes: commit 8eef91239e57 ("arm/arm64: KVM: map MMIO regions at creation time") Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Eric Auger <eric.auger@rehat.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> [ Handle dirty page logging failure case ] Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* arm/arm64: KVM: Take mmap_sem in stage2_unmap_vmMarc Zyngier2017-04-121-0/+2
| | | | | | | | | | | | | | | commit 90f6e150e44a0dc3883110eeb3ab35d1be42b6bb upstream. We don't hold the mmap_sem while searching for the VMAs when we try to unmap each memslot for a VM. Fix this properly to avoid unexpected results. Fixes: commit 957db105c997 ("arm/arm64: KVM: Introduce stage2_unmap_vm") Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* staging: android: ashmem: lseek failed due to no FMODE_LSEEK.Shuxiao Zhang2017-04-121-0/+1
| | | | | | | | | | | | | | | | | | | | | commit 97fbfef6bd597888485b653175fb846c6998b60c upstream. vfs_llseek will check whether the file mode has FMODE_LSEEK, no return failure. But ashmem can be lseek, so add FMODE_LSEEK to ashmem file. Comment From Greg Hackmann: ashmem_llseek() passes the llseek() call through to the backing shmem file. 91360b02ab48 ("ashmem: use vfs_llseek()") changed this from directly calling the file's llseek() op into a VFS layer call. This also adds a check for the FMODE_LSEEK bit, so without that bit ashmem_llseek() now always fails with -ESPIPE. Fixes: 91360b02ab48 ("ashmem: use vfs_llseek()") Signed-off-by: Shuxiao Zhang <zhangshuxiao@xiaomi.com> Tested-by: Greg Hackmann <ghackmann@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sysfs: be careful of error returns from ops->show()NeilBrown2017-04-121-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c8a139d001a1aab1ea8734db14b22dac9dd143b6 upstream. ops->show() can return a negative error code. Commit 65da3484d9be ("sysfs: correctly handle short reads on PREALLOC attrs.") (in v4.4) caused this to be stored in an unsigned 'size_t' variable, so errors would look like large numbers. As a result, if an error is returned, sysfs_kf_read() will return the value of 'count', typically 4096. Commit 17d0774f8068 ("sysfs: correctly handle read offset on PREALLOC attrs") (in v4.8) extended this error to use the unsigned large 'len' as a size for memmove(). Consequently, if ->show returns an error, then the first read() on the sysfs file will return 4096 and could return uninitialized memory to user-space. If the application performs a subsequent read, this will trigger a memmove() with extremely large count, and is likely to crash the machine is bizarre ways. This bug can currently only be triggered by reading from an md sysfs attribute declared with __ATTR_PREALLOC() during the brief period between when mddev_put() deletes an mddev from the ->all_mddevs list, and when mddev_delayed_delete() - which is scheduled on a workqueue - completes. Before this, an error won't be returned by the ->show() After this, the ->show() won't be called. I can reproduce it reliably only by putting delay like usleep_range(500000,700000); early in mddev_delayed_delete(). Then after creating an md device md0 run echo clear > /sys/block/md0/md/array_state; cat /sys/block/md0/md/array_state The bug can be triggered without the usleep. Fixes: 65da3484d9be ("sysfs: correctly handle short reads on PREALLOC attrs.") Fixes: 17d0774f8068 ("sysfs: correctly handle read offset on PREALLOC attrs") Signed-off-by: NeilBrown <neilb@suse.com> Acked-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/vmwgfx: fix integer overflow in vmw_surface_define_ioctl()Li Qiang2017-04-121-1/+4
| | | | | | | | | | | | | | | | commit e7e11f99564222d82f0ce84bd521e57d78a6b678 upstream. In vmw_surface_define_ioctl(), the 'num_sizes' is the sum of the 'req->mip_levels' array. This array can be assigned any value from the user space. As both the 'num_sizes' and the array is uint32_t, it is easy to make 'num_sizes' overflow. The later 'mip_levels' is used as the loop count. This can lead an oob write. Add the check of 'req->mip_levels' to avoid this. Signed-off-by: Li Qiang <liqiang6-s@360.cn> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/vmwgfx: Remove getparam error messageThomas Hellstrom2017-04-121-2/+0
| | | | | | | | | | | | | | commit 53e16798b0864464c5444a204e1bb93ae246c429 upstream. The mesa winsys sometimes uses unimplemented parameter requests to check for features. Remove the error message to avoid bloating the kernel log. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/ttm, drm/vmwgfx: Relax permission checking when opening surfacesThomas Hellstrom2017-04-125-23/+24
| | | | | | | | | | | | | | | | | commit fe25deb7737ce6c0879ccf79c99fa1221d428bf2 upstream. Previously, when a surface was opened using a legacy (non prime) handle, it was verified to have been created by a client in the same master realm. Relax this so that opening is also allowed recursively if the client already has the surface open. This works around a regression in svga mesa where opening of a shared surface is used recursively to obtain surface information. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/vmwgfx: avoid calling vzalloc with a 0 size in vmw_get_cap_3d_ioctl()Murray McAllister2017-04-121-1/+1
| | | | | | | | | | | | | | | commit 63774069d9527a1aeaa4aa20e929ef5e8e9ecc38 upstream. In vmw_get_cap_3d_ioctl(), a user can supply 0 for a size that is used in vzalloc(). This eventually calls dump_stack() (in warn_alloc()), which can leak useful addresses to dmesg. Add check to avoid a size of 0. Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-18 02:24:11 +0000