summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* Revert "zram: remove double compression logic"Jiri Slaby2022-08-312-10/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 37887783b3fef877bf34b8992c9199864da4afcb upstream. This reverts commit e7be8d1dd983156b ("zram: remove double compression logic") as it causes zram failures. It does not revert cleanly, PTR_ERR handling was introduced in the meantime. This is handled by appropriate IS_ERR. When under memory pressure, zs_malloc() can fail. Before the above commit, the allocation was retried with direct reclaim enabled (GFP_NOIO). After the commit, it is not -- only __GFP_KSWAPD_RECLAIM is tried. So when the failure occurs under memory pressure, the overlaying filesystem such as ext2 (mounted by ext4 module in this case) can emit failures, making the (file)system unusable: EXT4-fs warning (device zram0): ext4_end_bio:343: I/O error 10 writing to inode 16386 starting block 159744) Buffer I/O error on device zram0, logical block 159744 With direct reclaim, memory is really reclaimed and allocation succeeds, eventually. In the worst case, the oom killer is invoked, which is proper outcome if user sets up zram too large (in comparison to available RAM). This very diff doesn't apply to 5.19 (stable) cleanly (see PTR_ERR note above). Use revert of e7be8d1dd983 directly. Link: https://bugzilla.suse.com/show_bug.cgi?id=1202203 Link: https://lkml.kernel.org/r/20220810070609.14402-1-jslaby@suse.cz Fixes: e7be8d1dd983 ("zram: remove double compression logic") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Alexey Romanov <avromanov@sberdevices.ru> Cc: Dmitry Rokosov <ddrokosov@sberdevices.ru> Cc: Lukas Czerner <lczerner@redhat.com> Cc: <stable@vger.kernel.org> [5.19] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* riscv: dts: microchip: correct L2 cache interruptsHeinrich Schuchardt2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 34fc9cc3aebe8b9e27d3bc821543dd482dc686ca upstream. The "PolarFire SoC MSS Technical Reference Manual" documents the following PLIC interrupts: 1 - L2 Cache Controller Signals when a metadata correction event occurs 2 - L2 Cache Controller Signals when an uncorrectable metadata event occurs 3 - L2 Cache Controller Signals when a data correction event occurs 4 - L2 Cache Controller Signals when an uncorrectable data event occurs This differs from the SiFive FU540 which only has three L2 cache related interrupts. The sequence in the device tree is defined by an enum: enum {         DIR_CORR = 0,         DATA_CORR,         DATA_UNCORR,         DIR_UNCORR, }; So the correct sequence of the L2 cache interrupts is interrupts = <1>, <3>, <4>, <2>; [Conor] This manifests as an unusable system if the l2-cache driver is enabled, as the wrong interrupt gets cleared & the handler prints errors to the console ad infinitum. Fixes: 0fa6107eca41 ("RISC-V: Initial DTS for Microchip ICICLE board") CC: stable@vger.kernel.org # 5.15: e35b07a7df9b: riscv: dts: microchip: mpfs: Group tuples in interrupt properties Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* riscv: traps: add missing prototypeConor Dooley2022-08-312-1/+4
| | | | | | | | | | | | | | | | | commit d951b20b9def73dcc39a5379831525d0d2a537e9 upstream. Sparse complains: arch/riscv/kernel/traps.c:213:6: warning: symbol 'shadow_stack' was not declared. Should it be static? The variable is used in entry.S, so declare shadow_stack there alongside SHADOW_OVERFLOW_STACK_SIZE. Fixes: 31da94c25aea ("riscv: add VMAP_STACK overflow detection") Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220814141237.493457-5-mail@conchuod.ie Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* riscv: signal: fix missing prototype warningConor Dooley2022-08-312-0/+13
| | | | | | | | | | | | | | | | | | | commit b5c3aca86d2698c4850b6ee8b341938025d2780c upstream. Fix the warning: arch/riscv/kernel/signal.c:316:27: warning: no previous prototype for function 'do_notify_resume' [-Wmissing-prototypes] asmlinkage __visible void do_notify_resume(struct pt_regs *regs, All other functions in the file are static & none of the existing headers stood out as an obvious location. Create signal.h to hold the declaration. Fixes: e2c0cdfba7f6 ("RISC-V: User-facing API") Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220814141237.493457-4-mail@conchuod.ie Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xen/privcmd: fix error exit of privcmd_ioctl_dm_op()Juergen Gross2022-08-311-10/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit c5deb27895e017a0267de0a20d140ad5fcc55a54 upstream. The error exit of privcmd_ioctl_dm_op() is calling unlock_pages() potentially with pages being NULL, leading to a NULL dereference. Additionally lock_pages() doesn't check for pin_user_pages_fast() having been completely successful, resulting in potentially not locking all pages into memory. This could result in sporadic failures when using the related memory in user mode. Fix all of that by calling unlock_pages() always with the real number of pinned pages, which will be zero in case pages being NULL, and by checking the number of pages pinned by pin_user_pages_fast() matching the expected number of pages. Cc: <stable@vger.kernel.org> Fixes: ab520be8cd5d ("xen/privcmd: Add IOCTL_PRIVCMD_DM_OP") Reported-by: Rustam Subkhankulov <subkhankulov@ispras.ru> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Link: https://lore.kernel.org/r/20220825141918.3581-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ocfs2: fix freeing uninitialized resource on ocfs2_dlm_shutdownHeming Zhao2022-08-312-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 550842cc60987b269e31b222283ade3e1b6c7fc8 upstream. After commit 0737e01de9c4 ("ocfs2: ocfs2_mount_volume does cleanup job before return error"), any procedure after ocfs2_dlm_init() fails will trigger crash when calling ocfs2_dlm_shutdown(). ie: On local mount mode, no dlm resource is initialized. If ocfs2_mount_volume() fails in ocfs2_find_slot(), error handling will call ocfs2_dlm_shutdown(), then does dlm resource cleanup job, which will trigger kernel crash. This solution should bypass uninitialized resources in ocfs2_dlm_shutdown(). Link: https://lkml.kernel.org/r/20220815085754.20417-1-heming.zhao@suse.com Fixes: 0737e01de9c4 ("ocfs2: ocfs2_mount_volume does cleanup job before return error") Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* smb3: missing inode locks in punch holeDavid Howells2022-08-311-6/+6
| | | | | | | | | | | | commit ba0803050d610d5072666be727bca5e03e55b242 upstream. smb3 fallocate punch hole was not grabbing the inode or filemap_invalidate locks so could have race with pagemap reinstantiating the page. Cc: stable@vger.kernel.org Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nouveau: explicitly wait on the fence in nouveau_bo_move_m2mfKarol Herbst2022-08-311-0/+9
| | | | | | | | | | | | | | commit 6b04ce966a738ecdd9294c9593e48513c0dc90aa upstream. It is a bit unlcear to us why that's helping, but it does and unbreaks suspend/resume on a lot of GPUs without any known drawbacks. Cc: stable@vger.kernel.org # v5.15+ Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/156 Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220819200928.401416-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ACPI: processor: Remove freq Qos request for all CPUsRiwen Lu2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | commit 36527b9d882362567ceb4eea8666813280f30e6f upstream. The freq Qos request would be removed repeatedly if the cpufreq policy relates to more than one CPU. Then, it would cause the "called for unknown object" warning. Remove the freq Qos request for each CPU relates to the cpufreq policy, instead of removing repeatedly for the last CPU of it. Fixes: a1bb46c36ce3 ("ACPI: processor: Add QoS requests for all CPUs") Reported-by: Jeremy Linton <Jeremy.Linton@arm.com> Tested-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Riwen Lu <luriwen@kylinos.cn> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* shmem: update folio if shmem_replace_page() updates the pageMatthew Wilcox (Oracle)2022-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | commit 9dfb3b8d655022760ca68af11821f1c63aa547c3 upstream. If we allocate a new page, we need to make sure that our folio matches that new page. If we do end up in this code path, we store the wrong page in the shmem inode's page cache, and I would rather imagine that data corruption ensues. This will be solved by changing shmem_replace_page() to shmem_replace_folio(), but this is the minimal fix. Link: https://lkml.kernel.org/r/20220730042518.1264767-1-willy@infradead.org Fixes: da08e9b79323 ("mm/shmem: convert shmem_swapin_page() to shmem_swapin_folio()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: William Kucharski <william.kucharski@oracle.com> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "memcg: cleanup racy sum avoidance code"Shakeel Butt2022-08-311-2/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit dbb16df6443c59e8a1ef21c2272fcf387d600ddf upstream. This reverts commit 96e51ccf1af33e82f429a0d6baebba29c6448d0f. Recently we started running the kernel with rstat infrastructure on production traffic and begin to see negative memcg stats values. Particularly the 'sock' stat is the one which we observed having negative value. $ grep "sock " /mnt/memory/job/memory.stat sock 253952 total_sock 18446744073708724224 Re-run after couple of seconds $ grep "sock " /mnt/memory/job/memory.stat sock 253952 total_sock 53248 For now we are only seeing this issue on large machines (256 CPUs) and only with 'sock' stat. I think the networking stack increase the stat on one cpu and decrease it on another cpu much more often. So, this negative sock is due to rstat flusher flushing the stats on the CPU that has seen the decrement of sock but missed the CPU that has increments. A typical race condition. For easy stable backport, revert is the most simple solution. For long term solution, I am thinking of two directions. First is just reduce the race window by optimizing the rstat flusher. Second is if the reader sees a negative stat value, force flush and restart the stat collection. Basically retry but limited. Link: https://lkml.kernel.org/r/20220817172139.3141101-1-shakeelb@google.com Fixes: 96e51ccf1af33e8 ("memcg: cleanup racy sum avoidance code") Signed-off-by: Shakeel Butt <shakeelb@google.com> Cc: "Michal Koutný" <mkoutny@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Muchun Song <songmuchun@bytedance.com> Cc: David Hildenbrand <david@redhat.com> Cc: Yosry Ahmed <yosryahmed@google.com> Cc: Greg Thelen <gthelen@google.com> Cc: <stable@vger.kernel.org> [5.15] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* fbdev: fbcon: Properly revert changes when vc_resize() failedShigeru Yoshida2022-08-311-2/+25
| | | | | | | | | | | | | | | | | | | | | | commit a5a923038d70d2d4a86cb4e3f32625a5ee6e7e24 upstream. fbcon_do_set_font() calls vc_resize() when font size is changed. However, if if vc_resize() failed, current implementation doesn't revert changes for font size, and this causes inconsistent state. syzbot reported unable to handle page fault due to this issue [1]. syzbot's repro uses fault injection which cause failure for memory allocation, so vc_resize() failed. This patch fixes this issue by properly revert changes for font related date when vc_resize() failed. Link: https://syzkaller.appspot.com/bug?id=3443d3a1fa6d964dd7310a0cb1696d165a3e07c4 [1] Reported-by: syzbot+a168dbeaaa7778273c1b@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Signed-off-by: Helge Deller <deller@gmx.de> CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390: fix double free of GS and RI CBs on fork() failureBrian Foster2022-08-311-6/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 13cccafe0edcd03bf1c841de8ab8a1c8e34f77d9 upstream. The pointers for guarded storage and runtime instrumentation control blocks are stored in the thread_struct of the associated task. These pointers are initially copied on fork() via arch_dup_task_struct() and then cleared via copy_thread() before fork() returns. If fork() happens to fail after the initial task dup and before copy_thread(), the newly allocated task and associated thread_struct memory are freed via free_task() -> arch_release_task_struct(). This results in a double free of the guarded storage and runtime info structs because the fields in the failed task still refer to memory associated with the source task. This problem can manifest as a BUG_ON() in set_freepointer() (with CONFIG_SLAB_FREELIST_HARDENED enabled) or KASAN splat (if enabled) when running trinity syscall fuzz tests on s390x. To avoid this problem, clear the associated pointer fields in arch_dup_task_struct() immediately after the new task is copied. Note that the RI flag is still cleared in copy_thread() because it resides in thread stack memory and that is where stack info is copied. Signed-off-by: Brian Foster <bfoster@redhat.com> Fixes: 8d9047f8b967c ("s390/runtime instrumentation: simplify task exit handling") Fixes: 7b83c6297d2fc ("s390/guarded storage: simplify task exit handling") Cc: <stable@vger.kernel.org> # 4.15 Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20220816155407.537372-1-bfoster@redhat.com Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* cifs: skip extra NULL byte in filenamesPaulo Alcantara2022-08-311-10/+6
| | | | | | | | | | | | | | | | | | | | | | | | | commit a1d2eb51f0a33c28f5399a1610e66b3fbd24e884 upstream. Since commit: cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty alloc_path_with_tree_prefix() function was no longer including the trailing separator when @path is empty, although @out_len was still assuming a path separator thus adding an extra byte to the final filename. This has caused mount issues in some Synology servers due to the extra NULL byte in filenames when sending SMB2_CREATE requests with SMB2_FLAGS_DFS_OPERATIONS set. Fix this by checking if @path is not empty and then add extra byte for separator. Also, do not include any trailing NULL bytes in filename as MS-SMB2 requires it to be 8-byte aligned and not NULL terminated. Cc: stable@vger.kernel.org Fixes: 7eacba3b00a3 ("cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty") Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mm/mprotect: only reference swap pfn page if type matchPeter Xu2022-08-311-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 3d2f78f08cd8388035ac375e731ec1ac1b79b09d upstream. Yu Zhao reported a bug after the commit "mm/swap: Add swp_offset_pfn() to fetch PFN from swap entry" added a check in swp_offset_pfn() for swap type [1]: kernel BUG at include/linux/swapops.h:117! CPU: 46 PID: 5245 Comm: EventManager_De Tainted: G S O L 6.0.0-dbg-DEV #2 RIP: 0010:pfn_swap_entry_to_page+0x72/0xf0 Code: c6 48 8b 36 48 83 fe ff 74 53 48 01 d1 48 83 c1 08 48 8b 09 f6 c1 01 75 7b 66 90 48 89 c1 48 8b 09 f6 c1 01 74 74 5d c3 eb 9e <0f> 0b 48 ba ff ff ff ff 03 00 00 00 eb ae a9 ff 0f 00 00 75 13 48 RSP: 0018:ffffa59e73fabb80 EFLAGS: 00010282 RAX: 00000000ffffffe8 RBX: 0c00000000000000 RCX: ffffcd5440000000 RDX: 1ffffffffff7a80a RSI: 0000000000000000 RDI: 0c0000000000042b RBP: ffffa59e73fabb80 R08: ffff9965ca6e8bb8 R09: 0000000000000000 R10: ffffffffa5a2f62d R11: 0000030b372e9fff R12: ffff997b79db5738 R13: 000000000000042b R14: 0c0000000000042b R15: 1ffffffffff7a80a FS: 00007f549d1bb700(0000) GS:ffff99d3cf680000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000440d035b3180 CR3: 0000002243176004 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> change_pte_range+0x36e/0x880 change_p4d_range+0x2e8/0x670 change_protection_range+0x14e/0x2c0 mprotect_fixup+0x1ee/0x330 do_mprotect_pkey+0x34c/0x440 __x64_sys_mprotect+0x1d/0x30 It triggers because pfn_swap_entry_to_page() could be called upon e.g. a genuine swap entry. Fix it by only calling it when it's a write migration entry where the page* is used. [1] https://lore.kernel.org/lkml/CAOUHufaVC2Za-p8m0aiHw6YkheDcrO-C3wRGixwDS32VTS+k1w@mail.gmail.com/ Link: https://lkml.kernel.org/r/20220823221138.45602-1-peterx@redhat.com Fixes: 6c287605fd56 ("mm: remember exclusively mapped anonymous pages with PG_anon_exclusive") Signed-off-by: Peter Xu <peterx@redhat.com> Reported-by: Yu Zhao <yuzhao@google.com> Tested-by: Yu Zhao <yuzhao@google.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pteMiaohe Lin2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | commit ab74ef708dc51df7cf2b8a890b9c6990fac5c0c6 upstream. In MCOPY_ATOMIC_CONTINUE case with a non-shared VMA, pages in the page cache are installed in the ptes. But hugepage_add_new_anon_rmap is called for them mistakenly because they're not vm_shared. This will corrupt the page->mapping used by page cache code. Link: https://lkml.kernel.org/r/20220712130542.18836-1-linmiaohe@huawei.com Fixes: f619147104c8 ("userfaultfd: add UFFDIO_CONTINUE ioctl") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* bootmem: remove the vmemmap pages from kmemleak in put_page_bootmemLiu Shixin2022-08-311-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit dd0ff4d12dd284c334f7e9b07f8f335af856ac78 upstream. The vmemmap pages is marked by kmemleak when allocated from memblock. Remove it from kmemleak when freeing the page. Otherwise, when we reuse the page, kmemleak may report such an error and then stop working. kmemleak: Cannot insert 0xffff98fb6eab3d40 into the object search tree (overlaps existing) kmemleak: Kernel memory leak detector disabled kmemleak: Object 0xffff98fb6be00000 (size 335544320): kmemleak: comm "swapper", pid 0, jiffies 4294892296 kmemleak: min_count = 0 kmemleak: count = 0 kmemleak: flags = 0x1 kmemleak: checksum = 0 kmemleak: backtrace: Link: https://lkml.kernel.org/r/20220819094005.2928241-1-liushixin2@huawei.com Fixes: f41f2ed43ca5 (mm: hugetlb: free the vmemmap pages associated with each HugeTLB page) Signed-off-by: Liu Shixin <liushixin2@huawei.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/mm: do not trigger write fault when vma does not allow VM_WRITEGerald Schaefer2022-08-311-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 41ac42f137080bc230b5882e3c88c392ab7f2d32 upstream. For non-protection pXd_none() page faults in do_dat_exception(), we call do_exception() with access == (VM_READ | VM_WRITE | VM_EXEC). In do_exception(), vma->vm_flags is checked against that before calling handle_mm_fault(). Since commit 92f842eac7ee3 ("[S390] store indication fault optimization"), we call handle_mm_fault() with FAULT_FLAG_WRITE, when recognizing that it was a write access. However, the vma flags check is still only checking against (VM_READ | VM_WRITE | VM_EXEC), and therefore also calling handle_mm_fault() with FAULT_FLAG_WRITE in cases where the vma does not allow VM_WRITE. Fix this by changing access check in do_exception() to VM_WRITE only, when recognizing write access. Link: https://lkml.kernel.org/r/20220811103435.188481-3-david@redhat.com Fixes: 92f842eac7ee3 ("[S390] store indication fault optimization") Cc: <stable@vger.kernel.org> Reported-by: David Hildenbrand <david@redhat.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mm/damon/dbgfs: avoid duplicate context directory creationBadari Pulavarty2022-08-311-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit d26f60703606ab425eee9882b32a1781a8bed74d upstream. When user tries to create a DAMON context via the DAMON debugfs interface with a name of an already existing context, the context directory creation fails but a new context is created and added in the internal data structure, due to absence of the directory creation success check. As a result, memory could leak and DAMON cannot be turned on. An example test case is as below: # cd /sys/kernel/debug/damon/ # echo "off" > monitor_on # echo paddr > target_ids # echo "abc" > mk_context # echo "abc" > mk_context # echo $$ > abc/target_ids # echo "on" > monitor_on <<< fails Return value of 'debugfs_create_dir()' is expected to be ignored in general, but this is an exceptional case as DAMON feature is depending on the debugfs functionality and it has the potential duplicate name issue. This commit therefore fixes the issue by checking the directory creation failure and immediately return the error in the case. Link: https://lkml.kernel.org/r/20220821180853.2400-1-sj@kernel.org Fixes: 75c1c2b53c78 ("mm/damon/dbgfs: support multiple contexts") Signed-off-by: Badari Pulavarty <badari.pulavarty@intel.com> Signed-off-by: SeongJae Park <sj@kernel.org> Cc: <stable@vger.kernel.org> [ 5.15.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* asm-generic: sections: refactor memory_intersectsQuanyang Wang2022-08-311-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 0c7d7cc2b4fe2e74ef8728f030f0f1674f9f6aee upstream. There are two problems with the current code of memory_intersects: First, it doesn't check whether the region (begin, end) falls inside the region (virt, vend), that is (virt < begin && vend > end). The second problem is if vend is equal to begin, it will return true but this is wrong since vend (virt + size) is not the last address of the memory region but (virt + size -1) is. The wrong determination will trigger the misreporting when the function check_for_illegal_area calls memory_intersects to check if the dma region intersects with stext region. The misreporting is as below (stext is at 0x80100000): WARNING: CPU: 0 PID: 77 at kernel/dma/debug.c:1073 check_for_illegal_area+0x130/0x168 DMA-API: chipidea-usb2 e0002000.usb: device driver maps memory from kernel text or rodata [addr=800f0000] [len=65536] Modules linked in: CPU: 1 PID: 77 Comm: usb-storage Not tainted 5.19.0-yocto-standard #5 Hardware name: Xilinx Zynq Platform unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x58/0x70 dump_stack_lvl from __warn+0xb0/0x198 __warn from warn_slowpath_fmt+0x80/0xb4 warn_slowpath_fmt from check_for_illegal_area+0x130/0x168 check_for_illegal_area from debug_dma_map_sg+0x94/0x368 debug_dma_map_sg from __dma_map_sg_attrs+0x114/0x128 __dma_map_sg_attrs from dma_map_sg_attrs+0x18/0x24 dma_map_sg_attrs from usb_hcd_map_urb_for_dma+0x250/0x3b4 usb_hcd_map_urb_for_dma from usb_hcd_submit_urb+0x194/0x214 usb_hcd_submit_urb from usb_sg_wait+0xa4/0x118 usb_sg_wait from usb_stor_bulk_transfer_sglist+0xa0/0xec usb_stor_bulk_transfer_sglist from usb_stor_bulk_srb+0x38/0x70 usb_stor_bulk_srb from usb_stor_Bulk_transport+0x150/0x360 usb_stor_Bulk_transport from usb_stor_invoke_transport+0x38/0x440 usb_stor_invoke_transport from usb_stor_control_thread+0x1e0/0x238 usb_stor_control_thread from kthread+0xf8/0x104 kthread from ret_from_fork+0x14/0x2c Refactor memory_intersects to fix the two problems above. Before the 1d7db834a027e ("dma-debug: use memory_intersects() directly"), memory_intersects is called only by printk_late_init: printk_late_init -> init_section_intersects ->memory_intersects. There were few places where memory_intersects was called. When commit 1d7db834a027e ("dma-debug: use memory_intersects() directly") was merged and CONFIG_DMA_API_DEBUG is enabled, the DMA subsystem uses it to check for an illegal area and the calltrace above is triggered. [akpm@linux-foundation.org: fix nearby comment typo] Link: https://lkml.kernel.org/r/20220819081145.948016-1-quanyang.wang@windriver.com Fixes: 979559362516 ("asm/sections: add helpers to check for section data") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thierry Reding <treding@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* audit: move audit_return_fixup before the filtersRichard Guy Briggs2022-08-311-2/+2
| | | | | | | | | | | | | | | | commit d4fefa4801a1c2f9c0c7a48fbb0fdf384e89a4ab upstream. The success and return_code are needed by the filters. Move audit_return_fixup() before the filters. This was causing syscall auditing events to be missed. Link: https://github.com/linux-audit/audit-kernel/issues/138 Cc: stable@vger.kernel.org Fixes: 12c5e81d3fd0 ("audit: prepare audit_context for use in calling contexts beyond syscalls") Signed-off-by: Richard Guy Briggs <rgb@redhat.com> [PM: manual merge required] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* writeback: avoid use-after-free after removing deviceKhazhismel Kumykov2022-08-313-12/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit f87904c075515f3e1d8f4a7115869d3b914674fd upstream. When a disk is removed, bdi_unregister gets called to stop further writeback and wait for associated delayed work to complete. However, wb_inode_writeback_end() may schedule bandwidth estimation dwork after this has completed, which can result in the timer attempting to access the just freed bdi_writeback. Fix this by checking if the bdi_writeback is alive, similar to when scheduling writeback work. Since this requires wb->work_lock, and wb_inode_writeback_end() may get called from interrupt, switch wb->work_lock to an irqsafe lock. Link: https://lkml.kernel.org/r/20220801155034.3772543-1-khazhy@google.com Fixes: 45a2966fd641 ("writeback: fix bandwidth estimate for spiky workload") Signed-off-by: Khazhismel Kumykov <khazhy@google.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Michael Stapelberg <stapelberg+linux@google.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* loop: Check for overflow while configuring loopSiddh Raman Pant2022-08-311-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c490a0b5a4f36da3918181a8acdc6991d967c5f3 upstream. The userspace can configure a loop using an ioctl call, wherein a configuration of type loop_config is passed (see lo_ioctl()'s case on line 1550 of drivers/block/loop.c). This proceeds to call loop_configure() which in turn calls loop_set_status_from_info() (see line 1050 of loop.c), passing &config->info which is of type loop_info64*. This function then sets the appropriate values, like the offset. loop_device has lo_offset of type loff_t (see line 52 of loop.c), which is typdef-chained to long long, whereas loop_info64 has lo_offset of type __u64 (see line 56 of include/uapi/linux/loop.h). The function directly copies offset from info to the device as follows (See line 980 of loop.c): lo->lo_offset = info->lo_offset; This results in an overflow, which triggers a warning in iomap_iter() due to a call to iomap_iter_done() which has: WARN_ON_ONCE(iter->iomap.offset > iter->pos); Thus, check for negative value during loop_set_status_from_info(). Bug report: https://syzkaller.appspot.com/bug?id=c620fe14aac810396d3c3edc9ad73848bf69a29e Reported-and-tested-by: syzbot+a8e049cd3abd342936b6@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Siddh Raman Pant <code@siddh.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220823160810.181275-1-code@siddh.me Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/PAT: Have pat_enabled() properly reflect state when running on XenJan Beulich2022-08-311-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 72cbc8f04fe2fa93443c0fcccb7ad91dfea3d9ce upstream. After commit ID in the Fixes: tag, pat_enabled() returns false (because of PAT initialization being suppressed in the absence of MTRRs being announced to be available). This has become a problem: the i915 driver now fails to initialize when running PV on Xen (i915_gem_object_pin_map() is where I located the induced failure), and its error handling is flaky enough to (at least sometimes) result in a hung system. Yet even beyond that problem the keying of the use of WC mappings to pat_enabled() (see arch_can_pci_mmap_wc()) means that in particular graphics frame buffer accesses would have been quite a bit less optimal than possible. Arrange for the function to return true in such environments, without undermining the rest of PAT MSR management logic considering PAT to be disabled: specifically, no writes to the PAT MSR should occur. For the new boolean to live in .init.data, init_cache_modes() also needs moving to .init.text (where it could/should have lived already before). [ bp: This is the "small fix" variant for stable. It'll get replaced with a proper PAT and MTRR detection split upstream but that is too involved for a stable backport. - additional touchups to commit msg. Use cpu_feature_enabled(). ] Fixes: bdd8b6c98239 ("drm/i915: replace X86_FEATURE_PAT with pat_enabled()") Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Cc: Juergen Gross <jgross@suse.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://lore.kernel.org/r/9385fa60-fa5d-f559-a137-6608408f88b0@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/nospec: Unwreck the RSB stuffingPeter Zijlstra2022-08-311-41/+39
| | | | | | | | | | | | | | | | commit 4e3aa9238277597c6c7624f302d81a7b568b6f2d upstream. Commit 2b1299322016 ("x86/speculation: Add RSB VM Exit protections") made a right mess of the RSB stuffing, rewrite the whole thing to not suck. Thanks to Andrew for the enlightening comment about Post-Barrier RSB things so we can make this code less magical. Cc: stable@vger.kernel.org Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/YvuNdDWoUZSBjYcm@worktop.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/bugs: Add "unknown" reporting for MMIO Stale DataPawan Gupta2022-08-314-19/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 7df548840c496b0141fb2404b889c346380c2b22 upstream. Older Intel CPUs that are not in the affected processor list for MMIO Stale Data vulnerabilities currently report "Not affected" in sysfs, which may not be correct. Vulnerability status for these older CPUs is unknown. Add known-not-affected CPUs to the whitelist. Report "unknown" mitigation status for CPUs that are not in blacklist, whitelist and also don't enumerate MSR ARCH_CAPABILITIES bits that reflect hardware immunity to MMIO Stale Data vulnerabilities. Mitigation is not deployed when the status is unknown. [ bp: Massage, fixup. ] Fixes: 8d50cdf8b834 ("x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data") Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com> Suggested-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/a932c154772f2121794a5f2eded1a11013114711.1657846269.git.pawan.kumar.gupta@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/sev: Don't use cc_platform_has() for early SEV-SNP callsTom Lendacky2022-08-311-2/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit cdaa0a407f1acd3a44861e3aea6e3c7349e668f1 upstream. When running identity-mapped and depending on the kernel configuration, it is possible that the compiler uses jump tables when generating code for cc_platform_has(). This causes a boot failure because the jump table uses un-mapped kernel virtual addresses, not identity-mapped addresses. This has been seen with CONFIG_RETPOLINE=n. Similar to sme_encrypt_kernel(), use an open-coded direct check for the status of SNP rather than trying to eliminate the jump table. This preserves any code optimization in cc_platform_has() that can be useful post boot. It also limits the changes to SEV-specific files so that future compiler features won't necessarily require possible build changes just because they are not compatible with running identity-mapped. [ bp: Massage commit message. ] Fixes: 5e5ccff60a29 ("x86/sev: Add helper for validating pages in early enc attribute changes") Reported-by: Sean Christopherson <seanjc@google.com> Suggested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> # 5.19.x Link: https://lore.kernel.org/all/YqfabnTRxFSM+LoX@google.com/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/unwind/orc: Unwind ftrace trampolines with correct ORC entryChen Zhongjin2022-08-311-5/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit fc2e426b1161761561624ebd43ce8c8d2fa058da upstream. When meeting ftrace trampolines in ORC unwinding, unwinder uses address of ftrace_{regs_}call address to find the ORC entry, which gets next frame at sp+176. If there is an IRQ hitting at sub $0xa8,%rsp, the next frame should be sp+8 instead of 176. It makes unwinder skip correct frame and throw warnings such as "wrong direction" or "can't access registers", etc, depending on the content of the incorrect frame address. By adding the base address ftrace_{regs_}caller with the offset *ip - ops->trampoline*, we can get the correct address to find the ORC entry. Also change "caller" to "tramp_addr" to make variable name conform to its content. [ mingo: Clarified the changelog a bit. ] Fixes: 6be7fa3c74d1 ("ftrace, orc, x86: Handle ftrace dynamically allocated trampolines") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220819084334.244016-1-chenzhongjin@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/entry: Fix entry_INT80_compat for Xen PV guestsJuergen Gross2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5b9f0c4df1c1152403c738373fb063e9ffdac0a1 upstream. Commit c89191ce67ef ("x86/entry: Convert SWAPGS to swapgs and remove the definition of SWAPGS") missed one use case of SWAPGS in entry_INT80_compat(). Removing of the SWAPGS macro led to asm just using "swapgs", as it is accepting instructions in capital letters, too. This in turn leads to splats in Xen PV guests like: [ 36.145223] general protection fault, maybe for address 0x2d: 0000 [#1] PREEMPT SMP NOPTI [ 36.145794] CPU: 2 PID: 1847 Comm: ld-linux.so.2 Not tainted 5.19.1-1-default #1 \ openSUSE Tumbleweed f3b44bfb672cdb9f235aff53b57724eba8b9411b [ 36.146608] Hardware name: HP ProLiant ML350p Gen8, BIOS P72 11/14/2013 [ 36.148126] RIP: e030:entry_INT80_compat+0x3/0xa3 Fix that by open coding this single instance of the SWAPGS macro. Fixes: c89191ce67ef ("x86/entry: Convert SWAPGS to swapgs and remove the definition of SWAPGS") Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Jan Beulich <jbeulich@suse.com> Cc: <stable@vger.kernel.org> # 5.19 Link: https://lore.kernel.org/r/20220816071137.4893-1-jgross@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* perf/x86/lbr: Enable the branch type for the Arch LBR by defaultKan Liang2022-08-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 32ba156df1b1c8804a4e5be5339616945eafea22 upstream. On the platform with Arch LBR, the HW raw branch type encoding may leak to the perf tool when the SAVE_TYPE option is not set. In the intel_pmu_store_lbr(), the HW raw branch type is stored in lbr_entries[].type. If the SAVE_TYPE option is set, the lbr_entries[].type will be converted into the generic PERF_BR_* type in the intel_pmu_lbr_filter() and exposed to the user tools. But if the SAVE_TYPE option is NOT set by the user, the current perf kernel doesn't clear the field. The HW raw branch type leaks. There are two solutions to fix the issue for the Arch LBR. One is to clear the field if the SAVE_TYPE option is NOT set. The other solution is to unconditionally convert the branch type and expose the generic type to the user tools. The latter is implemented here, because - The branch type is valuable information. I don't see a case where you would not benefit from the branch type. (Stephane Eranian) - Not having the branch type DOES NOT save any space in the branch record (Stephane Eranian) - The Arch LBR HW can retrieve the common branch types from the LBR_INFO. It doesn't require the high overhead SW disassemble. Fixes: 47125db27e47 ("perf/x86/intel/lbr: Support Architectural LBR") Reported-by: Stephane Eranian <eranian@google.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20220816125612.2042397-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* perf/x86/intel: Fix pebs event constraints for ADLKan Liang2022-08-311-1/+1
| | | | | | | | | | | | | | | | | commit cde643ff75bc20c538dfae787ca3b587bab16b50 upstream. According to the latest event list, the LOAD_LATENCY PEBS event only works on the GP counter 0 and 1 for ADL and RPL. Update the pebs event constraints table. Fixes: f83d2f91d259 ("perf/x86/intel: Add Alder Lake Hybrid support") Reported-by: Ammy Yi <ammy.yi@intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20220818184429.2355857-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/boot: Don't propagate uninitialized boot_params->cc_blob_addressMichael Roth2022-08-312-1/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 4b1c742407571eff58b6de9881889f7ca7c4b4dc upstream. In some cases, bootloaders will leave boot_params->cc_blob_address uninitialized rather than zeroing it out. This field is only meant to be set by the boot/compressed kernel in order to pass information to the uncompressed kernel when SEV-SNP support is enabled. Therefore, there are no cases where the bootloader-provided values should be treated as anything other than garbage. Otherwise, the uncompressed kernel may attempt to access this bogus address, leading to a crash during early boot. Normally, sanitize_boot_params() would be used to clear out such fields but that happens too late: sev_enable() may have already initialized it to a valid value that should not be zeroed out. Instead, have sev_enable() zero it out unconditionally beforehand. Also ensure this happens for !CONFIG_AMD_MEM_ENCRYPT as well by also including this handling in the sev_enable() stub function. [ bp: Massage commit message and comments. ] Fixes: b190a043c49a ("x86/sev: Add SEV-SNP feature detection/setup") Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com> Reported-by: watnuss@gmx.de Signed-off-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=216387 Link: https://lore.kernel.org/r/20220823160734.89036-1-michael.roth@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: update generation of hole file extent item when merging holesFilipe Manana2022-08-311-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit e6e3dec6c3c288d556b991a85d5d8e3ee71e9046 upstream. When punching a hole into a file range that is adjacent with a hole and we are not using the no-holes feature, we expand the range of the adjacent file extent item that represents a hole, to save metadata space. However we don't update the generation of hole file extent item, which means a full fsync will not log that file extent item if the fsync happens in a later transaction (since commit 7f30c07288bb9e ("btrfs: stop copying old file extents when doing a full fsync")). For example, if we do this: $ mkfs.btrfs -f -O ^no-holes /dev/sdb $ mount /dev/sdb /mnt $ xfs_io -f -c "pwrite -S 0xab 2M 2M" /mnt/foobar $ sync We end up with 2 file extent items in our file: 1) One that represents the hole for the file range [0, 2M), with a generation of 7; 2) Another one that represents an extent covering the range [2M, 4M). After that if we do the following: $ xfs_io -c "fpunch 2M 2M" /mnt/foobar We end up with a single file extent item in the file, which represents a hole for the range [0, 4M) and with a generation of 7 - because we end dropping the data extent for range [2M, 4M) and then update the file extent item that represented the hole at [0, 2M), by increasing length from 2M to 4M. Then doing a full fsync and power failing: $ xfs_io -c "fsync" /mnt/foobar <power failure> will result in the full fsync not logging the file extent item that represents the hole for the range [0, 4M), because its generation is 7, which is lower than the generation of the current transaction (8). As a consequence, after mounting again the filesystem (after log replay), the region [2M, 4M) does not have a hole, it still points to the previous data extent. So fix this by always updating the generation of existing file extent items representing holes when we merge/expand them. This solves the problem and it's the same approach as when we merge prealloc extents that got written (at btrfs_mark_extent_written()). Setting the generation to the current transaction's generation is also what we do when merging the new hole extent map with the previous one or the next one. A test case for fstests, covering both cases of hole file extent item merging (to the left and to the right), will be sent soon. Fixes: 7f30c07288bb9e ("btrfs: stop copying old file extents when doing a full fsync") CC: stable@vger.kernel.org # 5.18+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: fix possible memory leak in btrfs_get_dev_args_from_path()Zixuan Fu2022-08-311-1/+4
| | | | | | | | | | | | | | | | | | | | | commit 9ea0106a7a3d8116860712e3f17cd52ce99f6707 upstream. In btrfs_get_dev_args_from_path(), btrfs_get_bdev_and_sb() can fail if the path is invalid. In this case, btrfs_get_dev_args_from_path() returns directly without freeing args->uuid and args->fsid allocated before, which causes memory leak. To fix these possible leaks, when btrfs_get_bdev_and_sb() fails, btrfs_put_dev_args_from_path() is called to clean up the memory. Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Fixes: faa775c41d655 ("btrfs: add a btrfs_get_dev_args_from_path helper") CC: stable@vger.kernel.org # 5.16 Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Zixuan Fu <r33s3n6@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: check if root is readonly while setting security xattrGoldwyn Rodrigues2022-08-311-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit b51111271b0352aa596c5ae8faf06939e91b3b68 upstream. For a filesystem which has btrfs read-only property set to true, all write operations including xattr should be denied. However, security xattr can still be changed even if btrfs ro property is true. This happens because xattr_permission() does not have any restrictions on security.*, system.* and in some cases trusted.* from VFS and the decision is left to the underlying filesystem. See comments in xattr_permission() for more details. This patch checks if the root is read-only before performing the set xattr operation. Testcase: DEV=/dev/vdb MNT=/mnt mkfs.btrfs -f $DEV mount $DEV $MNT echo "file one" > $MNT/f1 setfattr -n "security.one" -v 2 $MNT/f1 btrfs property set /mnt ro true setfattr -n "security.one" -v 1 $MNT/f1 umount $MNT CC: stable@vger.kernel.org # 4.9+ Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: fix space cache corruption and potential double allocationsOmar Sandoval2022-08-314-60/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit ced8ecf026fd8084cf175530ff85c76d6085d715 upstream. When testing space_cache v2 on a large set of machines, we encountered a few symptoms: 1. "unable to add free space :-17" (EEXIST) errors. 2. Missing free space info items, sometimes caught with a "missing free space info for X" error. 3. Double-accounted space: ranges that were allocated in the extent tree and also marked as free in the free space tree, ranges that were marked as allocated twice in the extent tree, or ranges that were marked as free twice in the free space tree. If the latter made it onto disk, the next reboot would hit the BUG_ON() in add_new_free_space(). 4. On some hosts with no on-disk corruption or error messages, the in-memory space cache (dumped with drgn) disagreed with the free space tree. All of these symptoms have the same underlying cause: a race between caching the free space for a block group and returning free space to the in-memory space cache for pinned extents causes us to double-add a free range to the space cache. This race exists when free space is cached from the free space tree (space_cache=v2) or the extent tree (nospace_cache, or space_cache=v1 if the cache needs to be regenerated). struct btrfs_block_group::last_byte_to_unpin and struct btrfs_block_group::progress are supposed to protect against this race, but commit d0c2f4fa555e ("btrfs: make concurrent fsyncs wait less when waiting for a transaction commit") subtly broke this by allowing multiple transactions to be unpinning extents at the same time. Specifically, the race is as follows: 1. An extent is deleted from an uncached block group in transaction A. 2. btrfs_commit_transaction() is called for transaction A. 3. btrfs_run_delayed_refs() -> __btrfs_free_extent() runs the delayed ref for the deleted extent. 4. __btrfs_free_extent() -> do_free_extent_accounting() -> add_to_free_space_tree() adds the deleted extent back to the free space tree. 5. do_free_extent_accounting() -> btrfs_update_block_group() -> btrfs_cache_block_group() queues up the block group to get cached. block_group->progress is set to block_group->start. 6. btrfs_commit_transaction() for transaction A calls switch_commit_roots(). It sets block_group->last_byte_to_unpin to block_group->progress, which is block_group->start because the block group hasn't been cached yet. 7. The caching thread gets to our block group. Since the commit roots were already switched, load_free_space_tree() sees the deleted extent as free and adds it to the space cache. It finishes caching and sets block_group->progress to U64_MAX. 8. btrfs_commit_transaction() advances transaction A to TRANS_STATE_SUPER_COMMITTED. 9. fsync calls btrfs_commit_transaction() for transaction B. Since transaction A is already in TRANS_STATE_SUPER_COMMITTED and the commit is for fsync, it advances. 10. btrfs_commit_transaction() for transaction B calls switch_commit_roots(). This time, the block group has already been cached, so it sets block_group->last_byte_to_unpin to U64_MAX. 11. btrfs_commit_transaction() for transaction A calls btrfs_finish_extent_commit(), which calls unpin_extent_range() for the deleted extent. It sees last_byte_to_unpin set to U64_MAX (by transaction B!), so it adds the deleted extent to the space cache again! This explains all of our symptoms above: * If the sequence of events is exactly as described above, when the free space is re-added in step 11, it will fail with EEXIST. * If another thread reallocates the deleted extent in between steps 7 and 11, then step 11 will silently re-add that space to the space cache as free even though it is actually allocated. Then, if that space is allocated *again*, the free space tree will be corrupted (namely, the wrong item will be deleted). * If we don't catch this free space tree corruption, it will continue to get worse as extents are deleted and reallocated. The v1 space_cache is synchronously loaded when an extent is deleted (btrfs_update_block_group() with alloc=0 calls btrfs_cache_block_group() with load_cache_only=1), so it is not normally affected by this bug. However, as noted above, if we fail to load the space cache, we will fall back to caching from the extent tree and may hit this bug. The easiest fix for this race is to also make caching from the free space tree or extent tree synchronous. Josef tested this and found no performance regressions. A few extra changes fall out of this change. Namely, this fix does the following, with step 2 being the crucial fix: 1. Factor btrfs_caching_ctl_wait_done() out of btrfs_wait_block_group_cache_done() to allow waiting on a caching_ctl that we already hold a reference to. 2. Change the call in btrfs_cache_block_group() of btrfs_wait_space_cache_v1_finished() to btrfs_caching_ctl_wait_done(), which makes us wait regardless of the space_cache option. 3. Delete the now unused btrfs_wait_space_cache_v1_finished() and space_cache_v1_done(). 4. Change btrfs_cache_block_group()'s `int load_cache_only` parameter to `bool wait` to more accurately describe its new meaning. 5. Change a few callers which had a separate call to btrfs_wait_block_group_cache_done() to use wait = true instead. 6. Make btrfs_wait_block_group_cache_done() static now that it's not used outside of block-group.c anymore. Fixes: d0c2f4fa555e ("btrfs: make concurrent fsyncs wait less when waiting for a transaction commit") CC: stable@vger.kernel.org # 5.12+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: add info when mount fails due to stale replace targetAnand Jain2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit f2c3bec215694fb8bc0ef5010f2a758d1906fc2d upstream. If the replace target device reappears after the suspended replace is cancelled, it blocks the mount operation as it can't find the matching replace-item in the metadata. As shown below, BTRFS error (device sda5): replace devid present without an active replace item To overcome this situation, the user can run the command btrfs device scan --forget <replace target device> and try the mount command again. And also, to avoid repeating the issue, superblock on the devid=0 must be wiped. wipefs -a device-path-to-devid=0. This patch adds some info when this situation occurs. Reported-by: Samuel Greiner <samuel@balkonien.org> Link: https://lore.kernel.org/linux-btrfs/b4f62b10-b295-26ea-71f9-9a5c9299d42c@balkonien.org/T/ CC: stable@vger.kernel.org # 5.0+ Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: replace: drop assert for suspended replaceAnand Jain2022-08-311-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 59a3991984dbc1fc47e5651a265c5200bd85464e upstream. If the filesystem mounts with the replace-operation in a suspended state and try to cancel the suspended replace-operation, we hit the assert. The assert came from the commit fe97e2e173af ("btrfs: dev-replace: replace's scrub must not be running in suspended state") that was actually not required. So just remove it. $ mount /dev/sda5 /btrfs BTRFS info (device sda5): cannot continue dev_replace, tgtdev is missing BTRFS info (device sda5): you may cancel the operation after 'mount -o degraded' $ mount -o degraded /dev/sda5 /btrfs <-- success. $ btrfs replace cancel /btrfs kernel: assertion failed: ret != -ENOTCONN, in fs/btrfs/dev-replace.c:1131 kernel: ------------[ cut here ]------------ kernel: kernel BUG at fs/btrfs/ctree.h:3750! After the patch: $ btrfs replace cancel /btrfs BTRFS info (device sda5): suspended dev_replace from /dev/sda5 (devid 1) to <missing disk> canceled Fixes: fe97e2e173af ("btrfs: dev-replace: replace's scrub must not be running in suspended state") CC: stable@vger.kernel.org # 5.0+ Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* btrfs: fix silent failure when deleting root referenceFilipe Manana2022-08-311-2/+3
| | | | | | | | | | | | | | | | | | | | commit 47bf225a8d2cccb15f7e8d4a1ed9b757dd86afd7 upstream. At btrfs_del_root_ref(), if btrfs_search_slot() returns an error, we end up returning from the function with a value of 0 (success). This happens because the function returns the value stored in the variable 'err', which is 0, while the error value we got from btrfs_search_slot() is stored in the 'ret' variable. So fix it by setting 'err' with the error value. Fixes: 8289ed9f93bef2 ("btrfs: replace the BUG_ON in btrfs_del_root_ref with proper error handling") CC: stable@vger.kernel.org # 5.16+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: lantiq_xrx200: restore buffer if memory allocation failedAleksander Jan Bajkowski2022-08-311-0/+1
| | | | | | | | | | | | | [ Upstream commit c9c3b1775f80fa21f5bff874027d2ccb10f5d90c ] In a situation where memory allocation fails, an invalid buffer address is stored. When this descriptor is used again, the system panics in the build_skb() function when accessing memory. Fixes: 7ea6cd16f159 ("lantiq: net: fix duplicated skb in rx descriptor ring") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: lantiq_xrx200: fix lock under memory pressureAleksander Jan Bajkowski2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | | [ Upstream commit c4b6e9341f930e4dd089231c0414758f5f1f9dbd ] When the xrx200_hw_receive() function returns -ENOMEM, the NAPI poll function immediately returns an error. This is incorrect for two reasons: * the function terminates without enabling interrupts or scheduling NAPI, * the error code (-ENOMEM) is returned instead of the number of received packets. After the first memory allocation failure occurs, packet reception is locked due to disabled interrupts from DMA.. Fixes: fe1a56420cf2 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: lantiq_xrx200: confirm skb is allocated before usingAleksander Jan Bajkowski2022-08-311-0/+6
| | | | | | | | | | | | | | | [ Upstream commit c8b043702dc0894c07721c5b019096cebc8c798f ] xrx200_hw_receive() assumes build_skb() always works and goes straight to skb_reserve(). However, build_skb() can fail under memory pressure. Add a check in case build_skb() failed to allocate and return NULL. Fixes: e015593573b3 ("net: lantiq_xrx200: convert to build_skb") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: stmmac: work around sporadic tx issue on link-upHeiner Kallweit2022-08-312-6/+11
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit a3a57bf07de23fe1ff779e0fdf710aa581c3ff73 ] This is a follow-up to the discussion in [0]. It seems to me that at least the IP version used on Amlogic SoC's sometimes has a problem if register MAC_CTRL_REG is written whilst the chip is still processing a previous write. But that's just a guess. Adding a delay between two writes to this register helps, but we can also simply omit the offending second write. This patch uses the second approach and is based on a suggestion from Qi Duan. Benefit of this approach is that we can save few register writes, also on not affected chip versions. [0] https://www.spinics.net/lists/netdev/msg831526.html Fixes: bfab27a146ed ("stmmac: add the experimental PCI support") Suggested-by: Qi Duan <qi.duan@amlogic.com> Suggested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/e99857ce-bd90-5093-ca8c-8cd480b5a0a2@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ionic: VF initial random MAC address if no assigned macR Mohamed Shah2022-08-311-5/+87
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 19058be7c48ceb3e60fa3948e24da1059bd68ee4 ] Assign a random mac address to the VF interface station address if it boots with a zero mac address in order to match similar behavior seen in other VF drivers. Handle the errors where the older firmware does not allow the VF to set its own station address. Newer firmware will allow the VF to set the station mac address if it hasn't already been set administratively through the PF. Setting it will also be allowed if the VF has trust. Fixes: fbb39807e9ae ("ionic: support sr-iov operations") Signed-off-by: R Mohamed Shah <mohamed@pensando.io> Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ionic: fix up issues with handling EAGAIN on FW cmdsShannon Nelson2022-08-311-1/+3
| | | | | | | | | | | | | | | | | | | [ Upstream commit 0fc4dd452d6c14828eed6369155c75c0ac15bab3 ] In looping on FW update tests we occasionally see the FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop waiting for the FW activate step to finsh inside the FW. The firmware is complaining that the done bit is set when a new dev_cmd is going to be processed. Doing a clean on the cmd registers and doorbell before exiting the wait-for-done and cleaning the done bit before the sleep prevents this from occurring. Fixes: fbfb8031533c ("ionic: Add hardware init and device commands") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ionic: clear broken state on generation changeShannon Nelson2022-08-311-0/+3
| | | | | | | | | | | | | | | | | | [ Upstream commit 9cb9dadb8f45c67e4310e002c2f221b70312b293 ] There is a case found in heavy testing where a link flap happens just before a firmware Recovery event and the driver gets stuck in the BROKEN state. This comes from the driver getting interrupted by a FW generation change when coming back up from the link flap, and the call to ionic_start_queues() in ionic_link_status_check() fails. This can be addressed by having the fw_up code clear the BROKEN bit if seen, rather than waiting for a user to manually force the interface down and then back up. Fixes: 9e8eaf8427b6 ("ionic: stop watchdog when in broken state") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* rxrpc: Fix locking in rxrpc's sendmsgDavid Howells2022-08-312-39/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit b0f571ecd7943423c25947439045f0d352ca3dbf ] Fix three bugs in the rxrpc's sendmsg implementation: (1) rxrpc_new_client_call() should release the socket lock when returning an error from rxrpc_get_call_slot(). (2) rxrpc_wait_for_tx_window_intr() will return without the call mutex held in the event that we're interrupted by a signal whilst waiting for tx space on the socket or relocking the call mutex afterwards. Fix this by: (a) moving the unlock/lock of the call mutex up to rxrpc_send_data() such that the lock is not held around all of rxrpc_wait_for_tx_window*() and (b) indicating to higher callers whether we're return with the lock dropped. Note that this means recvmsg() will not block on this call whilst we're waiting. (3) After dropping and regaining the call mutex, rxrpc_send_data() needs to go and recheck the state of the tx_pending buffer and the tx_total_len check in case we raced with another sendmsg() on the same call. Thinking on this some more, it might make sense to have different locks for sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating that a call is dead before a sendmsg() to that call returns - but that can currently happen anyway. Without fix (2), something like the following can be induced: WARNING: bad unlock balance detected! 5.16.0-rc6-syzkaller #0 Not tainted ------------------------------------- syz-executor011/3597 is trying to release lock (&call->user_mutex) at: [<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748 but there are no more locks to release! other info that might help us debug this: no locks held by syz-executor011/3597. ... Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline] __lock_release kernel/locking/lockdep.c:5306 [inline] lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657 __mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900 rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748 rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561 sock_sendmsg_nosec net/socket.c:704 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:724 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2409 ___sys_sendmsg+0xf3/0x170 net/socket.c:2463 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2492 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae [Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this] Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Reported-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com cc: Hawkins Jiawei <yin31149@gmail.com> cc: Khalid Masum <khalid.masum.92@gmail.com> cc: Dan Carpenter <dan.carpenter@oracle.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/166135894583.600315.7170979436768124075.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2Lorenzo Bianconi2022-08-312-10/+17
| | | | | | | | | | | | | [ Upstream commit 0cf731f9ebb5bf6f252055bebf4463a5c0bd490b ] Properly report hw rx hash for mt7986 chipset accroding to the new dma descriptor layout. Fixes: 197c9e9b17b11 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/091394ea4e705fbb35f828011d98d0ba33808f69.1661257293.git.lorenzo@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: ethernet: mtk_eth_soc: enable rx cksum offload for MTK_NETSYS_V2Lorenzo Bianconi2022-08-311-2/+9
| | | | | | | | | | | [ Upstream commit da6e113ff010815fdd21ee1e9af2e8d179a2680f ] Enable rx checksum offload for mt7986 chipset. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/c8699805c18f7fd38315fcb8da2787676d83a32c.1654544585.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* i40e: Fix incorrect address type for IPv6 flow rulesSylwester Dziedziuch2022-08-311-1/+1
| | | | | | | | | | | | | | | | | | [ Upstream commit bcf3a156429306070afbfda5544f2b492d25e75b ] It was not possible to create 1-tuple flow director rule for IPv6 flow type. It was caused by incorrectly checking for source IP address when validating user provided destination IP address. Fix this by changing ip6src to correct ip6dst address in destination IP address validation for IPv6 flow type. Fixes: efca91e89b67 ("i40e: Add flow director support for IPv6") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.46.0) at 2025-04-22 14:41:41 +0000