summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* clk: imx8mq: Mark AHB clock as criticalAbel Vesa2019-10-071-1/+2
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9b9c60bed562c3718ae324a86f3f30a4ff983cf8 ] Initially, the TMU_ROOT clock was marked as critical, which automatically made the AHB clock to stay always on. Since the TMU_ROOT clock is not marked as critical anymore, following commit: "clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT" all the clocks that derive from ipg_root clock (and implicitly ahb clock) would also have to enable, along with their own gate, the AHB clock. But considering that AHB is actually a bus that has to be always on, we mark it as critical in the clock provider driver and then all the clocks that derive from it can be controlled through the dedicated per IP gate which follows after the ipg_root clock. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Tested-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* gpu: drm: radeon: Fix a possible null-pointer dereference in ↵Jia-Ju Bai2019-10-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | radeon_connector_set_property() [ Upstream commit f3eb9b8f67bc28783eddc142ad805ebdc53d6339 ] In radeon_connector_set_property(), there is an if statement on line 743 to check whether connector->encoder is NULL: if (connector->encoder) When connector->encoder is NULL, it is used on line 755: if (connector->encoder->crtc) Thus, a possible null-pointer dereference may occur. To fix this bug, connector->encoder is checked before being used. This bug is found by a static analysis tool STCheck written by us. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/radeon: Fix EEH during kexecKyleMahlkuch2019-10-071-0/+8
| | | | | | | | | | | | [ Upstream commit 6f7fe9a93e6c09bf988c5059403f5f88e17e21e6 ] During kexec some adapters hit an EEH since they are not properly shut down in the radeon_pci_shutdown() function. Adding radeon_suspend_kms() fixes this issue. Signed-off-by: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/amdgpu: Fix hard hang for S/G display BOs.Andrey Grodzovsky2019-10-072-5/+5
| | | | | | | | | | | | | | | | | | | [ Upstream commit e4c4073b0139d055d43a9568690fc560aab4fa5c ] HW requires for caching to be unset for scanout BO mappings when the BO placement is in GTT memory. Usually the flag to unset is passed from user mode but for FB mode this was missing. v2: Keep all BO placement logic in amdgpu_display_supported_domains Suggested-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Tested-by: Shirish S <shirish.s@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/rockchip: Check for fast link training before enabling psrSean Paul2019-10-071-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit ad309284a52be47c8b3126c9376358bf381861bc ] Once we start shutting off the link during PSR, we're going to want fast training to work. If the display doesn't support fast training, don't enable psr. Changes in v2: - None Changes in v3: - None Changes in v4: - None Changes in v5: - None Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-3-sean@poorly.run Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-2-sean@poorly.run Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@poorly.run Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-8-sean@poorly.run Cc: Zain Wang <wzz@rock-chips.com> Cc: Tomasz Figa <tfiga@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-8-sean@poorly.run Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/panel: check failure cases in the probe funcNavid Emamdoost2019-10-071-0/+13
| | | | | | | | | | | | | | | | | | [ Upstream commit afd6d4f5a52c16e1483328ac074abb1cde92c29f ] The following function calls may fail and return NULL, so the null check is added. of_graph_get_next_endpoint of_graph_get_remote_port_parent of_graph_get_remote_port Update: Thanks to Sam Ravnborg, for suggession on the use of goto to avoid leaking endpoint. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190724195534.9303-1-navid.emamdoost@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/stm: attach gem fence to atomic stateAhmad Fatoum2019-10-071-0/+2
| | | | | | | | | | | | | | | | [ Upstream commit 8fabc9c3109a71b3577959a05408153ae69ccd8d ] To properly synchronize with other devices the fence from the GEM object backing the framebuffer needs to be attached to the atomic state, so the commit work can wait on fence signaling. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190712084228.8338-1-l.stach@pengutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/tinydrm/Kconfig: drivers: Select BACKLIGHT_CLASS_DEVICENoralf Trønnes2019-10-071-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3389669ac5ea598562673c04971d7bb0fab0e9f1 ] The mipi_dbi helper is missing a dependency on DRM_KMS_HELPER and putting that in revealed this problem: drivers/video/fbdev/Kconfig:12:error: recursive dependency detected! drivers/video/fbdev/Kconfig:12: symbol FB is selected by DRM_KMS_FB_HELPER drivers/gpu/drm/Kconfig:75: symbol DRM_KMS_FB_HELPER depends on DRM_KMS_HELPER drivers/gpu/drm/Kconfig:69: symbol DRM_KMS_HELPER is selected by TINYDRM_MIPI_DBI drivers/gpu/drm/tinydrm/Kconfig:11: symbol TINYDRM_MIPI_DBI is selected by TINYDRM_HX8357D drivers/gpu/drm/tinydrm/Kconfig:15: symbol TINYDRM_HX8357D depends on BACKLIGHT_CLASS_DEVICE drivers/video/backlight/Kconfig:144: symbol BACKLIGHT_CLASS_DEVICE is selected by FB_BACKLIGHT drivers/video/fbdev/Kconfig:187: symbol FB_BACKLIGHT depends on FB A symbol that selects DRM_KMS_HELPER can not depend on BACKLIGHT_CLASS_DEVICE. The reason for this is that DRM_KMS_FB_HELPER selects FB instead of depending on it. The tinydrm drivers have somehow gotten away with depending on BACKLIGHT_CLASS_DEVICE because DRM_TINYDRM selects DRM_KMS_HELPER and the drivers depend on that symbol. An audit shows that all DRM drivers that select DRM_KMS_HELPER and use BACKLIGHT_CLASS_DEVICE, selects it: DRM_TILCDC, DRM_GMA500, DRM_SHMOBILE, DRM_NOUVEAU, DRM_FSL_DCU, DRM_I915, DRM_RADEON, DRM_AMDGPU, DRM_PARADE_PS8622 Documentation/kbuild/kconfig-language.txt has a note regarding select: 1. 'select should be used with care since it doesn't visit dependencies.' This is not a problem since BACKLIGHT_CLASS_DEVICE doesn't have any dependencies. 2. 'In general use select only for non-visible symbols' BACKLIGHT_CLASS_DEVICE is user visible. The real solution to this would be to have DRM_KMS_FB_HELPER depend on the user visible symbol FB. That is a can of worms I'm not willing to tackle. I fear that such a change will result in me handling difficult fallouts for the next weeks. So I'm following DRM suite here. Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: David Lechner <david@lechnology.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190722104312.16184-7-noralf@tronnes.org Signed-off-by: Sasha Levin <sashal@kernel.org>
* video: ssd1307fb: Start page range at page_offsetMarko Kohtala2019-10-071-1/+1
| | | | | | | | | | | | | | | | | | | | [ Upstream commit dd9782834dd9dde3624ff1acea8859f3d3e792d4 ] The page_offset was only applied to the end of the page range. This caused the display updates to cause a scrolling effect on the display because the amount of data written to the display did not match the range display expected. Fixes: 301bc0675b67 ("video: ssd1307fb: Make use of horizontal addressing mode") Signed-off-by: Marko Kohtala <marko.kohtala@okoko.fi> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190618074111.9309-4-marko.kohtala@okoko.fi Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/amd/display: add monitor patch to add T7 delayAnthony Koo2019-10-072-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 88eac241a1fc500ce5274a09ddc4bd5fc2b5adb6 ] [Why] Specifically to one panel, TCON is able to accept active video signal quickly, but the Source Driver requires 2-3 frames of extra time. It is a Panel issue since TCON needs to take care of all Sink requirements including Source Driver. But in this case it does not. Customer is asking to add fixed T7 delay as panel workaround. [How] Add monitor specific patch to add T7 delay Signed-off-by: Anthony Koo <anthony.koo@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/panel: simple: fix AUO g185han01 horizontal blankingLucas Stach2019-10-071-3/+3
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit f8c6bfc612b56f02e1b8fae699dff12738aaf889 ] The horizontal blanking periods are too short, as the values are specified for a single LVDS channel. Since this panel is dual LVDS they need to be doubled. With this change the panel reaches its nominal vrefresh rate of 60Fps, instead of the 64Fps with the current wrong blanking. Philipp Zabel added: The datasheet specifies 960 active clocks + 40/128/160 clocks blanking on each of the two LVDS channels (min/typical/max), so doubled this is now correct. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/1562764060.23869.12.camel@pengutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/vkms: Avoid assigning 0 for possible_crtcRodrigo Siqueira2019-10-074-8/+8
| | | | | | | | | | | | | | | | | [ Upstream commit e9d85f731de06a35d2ae6cdcf7d0e037c98ef41a ] When vkms invoke drm_universal_plane_init(), it sets 0 for possible_crtcs parameter which means that planes can't be attached to any CRTC. It currently works due to some safeguard in the drm_crtc file; however, it is possible to identify the problem by trying to append a second connector. This patch fixes this issue by modifying vkms_plane_init() to accept an index parameter which makes the code a little bit more flexible and avoid set zero to possible_crtcs. Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/d67849c62a8d8ace1a0af455998b588798a4c45f.1561491964.git.rodrigosiqueiramelo@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/bridge: tc358767: Increase AUX transfer length limitAndrey Smirnov2019-10-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e0655feaec62d5139b6b13a7b1bbb1ab8f1c2d83 ] According to the datasheet tc358767 can transfer up to 16 bytes via its AUX channel, so the artificial limit of 8 appears to be too low. However only up to 15-bytes seem to be actually supported and trying to use 16-byte transfers results in transfers failing sporadically (with bogus status in case of I2C transfers), so limit it to 15. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Chris Healy <cphealy@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-9-andrew.smirnov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/vkms: Fix crc worker racesDaniel Vetter2019-10-073-16/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 18d0952a838ba559655b0cd9cf85097ad63d9bca ] The issue we have is that the crc worker might fall behind. We've tried to handle this by tracking both the earliest frame for which it still needs to compute a crc, and the last one. Plus when the crtc_state changes, we have a new work item, which are all run in order due to the ordered workqueue we allocate for each vkms crtc. Trouble is there's been a few small issues in the current code: - we need to capture frame_end in the vblank hrtimer, not in the worker. The worker might run much later, and then we generate a lot of crc for which there's already a different worker queued up. - frame number might be 0, so create a new crc_pending boolean to track this without confusion. - we need to atomically grab frame_start/end and clear it, so do that all in one go. This is not going to create a new race, because if we race with the hrtimer then our work will be re-run. - only race that can happen is the following: 1. worker starts 2. hrtimer runs and updates frame_end 3. worker grabs frame_start/end, already reading the new frame_end, and clears crc_pending 4. hrtimer calls queue_work() 5. worker completes 6. worker gets re-run, crc_pending is false Explain this case a bit better by rewording the comment. v2: Demote warning level output to debug when we fail to requeue, this is expected under high load when the crc worker can't quite keep up. Cc: Shayenne Moura <shayenneluzmoura@gmail.com> Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Cc: Haneen Mohammed <hamohammed.sa@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Tested-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190606222751.32567-2-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: sched: taprio: Avoid division by zero on invalid link speedVladimir Oltean2019-10-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9a9251a3534745d08a92abfeca0ca467b912b5f6 ] The check in taprio_set_picos_per_byte is currently not robust enough and will trigger this division by zero, due to e.g. PHYLINK not setting kset->base.speed when there is no PHY connected: [ 27.109992] Division by zero in kernel. [ 27.113842] CPU: 1 PID: 198 Comm: tc Not tainted 5.3.0-rc5-01246-gc4006b8c2637-dirty #212 [ 27.121974] Hardware name: Freescale LS1021A [ 27.126234] [<c03132e0>] (unwind_backtrace) from [<c030d8b8>] (show_stack+0x10/0x14) [ 27.133938] [<c030d8b8>] (show_stack) from [<c10b21b0>] (dump_stack+0xb0/0xc4) [ 27.141124] [<c10b21b0>] (dump_stack) from [<c10af97c>] (Ldiv0_64+0x8/0x18) [ 27.148052] [<c10af97c>] (Ldiv0_64) from [<c0700260>] (div64_u64+0xcc/0xf0) [ 27.154978] [<c0700260>] (div64_u64) from [<c07002d0>] (div64_s64+0x4c/0x68) [ 27.161993] [<c07002d0>] (div64_s64) from [<c0f3d890>] (taprio_set_picos_per_byte+0xe8/0xf4) [ 27.170388] [<c0f3d890>] (taprio_set_picos_per_byte) from [<c0f3f614>] (taprio_change+0x668/0xcec) [ 27.179302] [<c0f3f614>] (taprio_change) from [<c0f2bc24>] (qdisc_create+0x1fc/0x4f4) [ 27.187091] [<c0f2bc24>] (qdisc_create) from [<c0f2c0c8>] (tc_modify_qdisc+0x1ac/0x6f8) [ 27.195055] [<c0f2c0c8>] (tc_modify_qdisc) from [<c0ee9604>] (rtnetlink_rcv_msg+0x268/0x2dc) [ 27.203449] [<c0ee9604>] (rtnetlink_rcv_msg) from [<c0f4fef0>] (netlink_rcv_skb+0xe0/0x114) [ 27.211756] [<c0f4fef0>] (netlink_rcv_skb) from [<c0f4f6cc>] (netlink_unicast+0x1b4/0x22c) [ 27.219977] [<c0f4f6cc>] (netlink_unicast) from [<c0f4fa84>] (netlink_sendmsg+0x284/0x340) [ 27.228198] [<c0f4fa84>] (netlink_sendmsg) from [<c0eae5fc>] (sock_sendmsg+0x14/0x24) [ 27.235988] [<c0eae5fc>] (sock_sendmsg) from [<c0eaedf8>] (___sys_sendmsg+0x214/0x228) [ 27.243863] [<c0eaedf8>] (___sys_sendmsg) from [<c0eb015c>] (__sys_sendmsg+0x50/0x8c) [ 27.251652] [<c0eb015c>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54) [ 27.259524] Exception stack(0xe8045fa8 to 0xe8045ff0) [ 27.264546] 5fa0: b6f608c8 000000f8 00000003 bed7e2f0 00000000 00000000 [ 27.272681] 5fc0: b6f608c8 000000f8 004ce54c 00000128 5d3ce8c7 00000000 00000026 00505c9c [ 27.280812] 5fe0: 00000070 bed7e298 004ddd64 b6dd1e64 Russell King points out that the ethtool API says zero is a valid return value of __ethtool_get_link_ksettings: * If it is enabled then they are read-only; if the link * is up they represent the negotiated link mode; if the link is down, * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. So, it seems that taprio is not following the API... I'd suggest either fixing taprio, or getting agreement to change the ethtool API. The chosen path was to fix taprio. Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: sched: cbs: Avoid division by zero when calculating the port rateVladimir Oltean2019-10-071-1/+1
| | | | | | | | | | | | | | | [ Upstream commit 83c8c3cf45163f0c823db37be6ab04dfcf8ac751 ] As explained in the "net: sched: taprio: Avoid division by zero on invalid link speed" commit, it is legal for the ethtool API to return zero as a link speed. So guard against it to ensure we don't perform a division by zero in kernel. Fixes: e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ptp_qoriq: Initialize the registers' spinlock before calling ptp_qoriq_settimeVladimir Oltean2019-10-071-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit db34a4714c013b644eec2de0ec81b1f0373b8b93 ] Because ptp_qoriq_settime is being called prior to spin_lock_init, the following stack trace can be seen at driver probe time: [ 2.269117] the code is fine but needs lockdep annotation. [ 2.274569] turning off the locking correctness validator. [ 2.280027] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc7-01478-g01eaa67a4797 #263 [ 2.288073] Hardware name: Freescale LS1021A [ 2.292337] [<c0313cb4>] (unwind_backtrace) from [<c030e11c>] (show_stack+0x10/0x14) [ 2.300045] [<c030e11c>] (show_stack) from [<c1219440>] (dump_stack+0xcc/0xf8) [ 2.307235] [<c1219440>] (dump_stack) from [<c03b9b44>] (register_lock_class+0x730/0x73c) [ 2.315372] [<c03b9b44>] (register_lock_class) from [<c03b6190>] (__lock_acquire+0x78/0x270c) [ 2.323856] [<c03b6190>] (__lock_acquire) from [<c03b90cc>] (lock_acquire+0xe0/0x22c) [ 2.331649] [<c03b90cc>] (lock_acquire) from [<c123c310>] (_raw_spin_lock_irqsave+0x54/0x68) [ 2.340048] [<c123c310>] (_raw_spin_lock_irqsave) from [<c0e73fe4>] (ptp_qoriq_settime+0x38/0x80) [ 2.348878] [<c0e73fe4>] (ptp_qoriq_settime) from [<c0e746d4>] (ptp_qoriq_init+0x1f8/0x484) [ 2.357189] [<c0e746d4>] (ptp_qoriq_init) from [<c0e74aac>] (ptp_qoriq_probe+0xd0/0x184) [ 2.365243] [<c0e74aac>] (ptp_qoriq_probe) from [<c0b0a07c>] (platform_drv_probe+0x48/0x9c) [ 2.373555] [<c0b0a07c>] (platform_drv_probe) from [<c0b07a14>] (really_probe+0x1c4/0x400) [ 2.381779] [<c0b07a14>] (really_probe) from [<c0b07e28>] (driver_probe_device+0x78/0x1b8) [ 2.390003] [<c0b07e28>] (driver_probe_device) from [<c0b081d0>] (device_driver_attach+0x58/0x60) [ 2.398832] [<c0b081d0>] (device_driver_attach) from [<c0b082d4>] (__driver_attach+0xfc/0x160) [ 2.407402] [<c0b082d4>] (__driver_attach) from [<c0b05a84>] (bus_for_each_dev+0x68/0xb4) [ 2.415539] [<c0b05a84>] (bus_for_each_dev) from [<c0b06b68>] (bus_add_driver+0x104/0x20c) [ 2.423763] [<c0b06b68>] (bus_add_driver) from [<c0b0909c>] (driver_register+0x78/0x10c) [ 2.431815] [<c0b0909c>] (driver_register) from [<c030313c>] (do_one_initcall+0x8c/0x3ac) [ 2.439954] [<c030313c>] (do_one_initcall) from [<c1f013f4>] (kernel_init_freeable+0x468/0x548) [ 2.448610] [<c1f013f4>] (kernel_init_freeable) from [<c12344d8>] (kernel_init+0x8/0x10c) [ 2.456745] [<c12344d8>] (kernel_init) from [<c03010b4>] (ret_from_fork+0x14/0x20) [ 2.464273] Exception stack(0xea89ffb0 to 0xea89fff8) [ 2.469297] ffa0: 00000000 00000000 00000000 00000000 [ 2.477432] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.485566] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 Fixes: ff54571a747b ("ptp_qoriq: convert to use ptp_qoriq_init/free") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xen-netfront: do not use ~0U as error return value for xennet_fill_frags()Dongli Zhang2019-10-071-8/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit a761129e3625688310aecf26e1be9e98e85f8eb5 ] xennet_fill_frags() uses ~0U as return value when the sk_buff is not able to cache extra fragments. This is incorrect because the return type of xennet_fill_frags() is RING_IDX and 0xffffffff is an expected value for ring buffer index. In the situation when the rsp_cons is approaching 0xffffffff, the return value of xennet_fill_frags() may become 0xffffffff which xennet_poll() (the caller) would regard as error. As a result, queue->rx.rsp_cons is set incorrectly because it is updated only when there is error. If there is no error, xennet_poll() would be responsible to update queue->rx.rsp_cons. Finally, queue->rx.rsp_cons would point to the rx ring buffer entries whose queue->rx_skbs[i] and queue->grant_rx_ref[i] are already cleared to NULL. This leads to NULL pointer access in the next iteration to process rx ring buffer entries. The symptom is similar to the one fixed in commit 00b368502d18 ("xen-netfront: do not assume sk_buff_head list is empty in error handling"). This patch changes the return type of xennet_fill_frags() to indicate whether it is successful or failed. The queue->rx.rsp_cons will be always updated inside this function. Fixes: ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/rds: Fix error handling in rds_ib_add_one()Dotan Barak2019-10-071-3/+3
| | | | | | | | | | | | | | | | | [ Upstream commit d64bf89a75b65f83f06be9fb8f978e60d53752db ] rds_ibdev:ipaddr_list and rds_ibdev:conn_list are initialized after allocation some resources such as protection domain. If allocation of such resources fail, then these uninitialized variables are accessed in rds_ib_dev_free() in failure path. This can potentially crash the system. The code has been updated to initialize these variables very early in the function. Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Sudhakar Dindukurti <sudhakar.dindukurti@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* udp: only do GSO if # of segs > 1Josh Hunt2019-10-073-20/+18
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 4094871db1d65810acab3d57f6089aa39ef7f648 ] Prior to this change an application sending <= 1MSS worth of data and enabling UDP GSO would fail if the system had SW GSO enabled, but the same send would succeed if HW GSO offload is enabled. In addition to this inconsistency the error in the SW GSO case does not get back to the application if sending out of a real device so the user is unaware of this failure. With this change we only perform GSO if the # of segments is > 1 even if the application has enabled segmentation. I've also updated the relevant udpgso selftests. Fixes: bec1f6f69736 ("udp: generate gso with UDP_SEGMENT") Signed-off-by: Josh Hunt <johunt@akamai.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tcp: adjust rto_base in retransmits_timed_out()Eric Dumazet2019-10-071-2/+7
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3256a2d6ab1f71f9a1bd2d7f6f18eb8108c48d17 ] The cited commit exposed an old retransmits_timed_out() bug which assumed it could call tcp_model_timeout() with TCP_RTO_MIN as rto_base for all states. But flows in SYN_SENT or SYN_RECV state uses a different RTO base (1 sec instead of 200 ms, unless BPF choses another value) This caused a reduction of SYN retransmits from 6 to 4 with the default /proc/sys/net/ipv4/tcp_syn_retries value. Fixes: a41e8a88b06e ("tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Marek Majkowski <marek@cloudflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: dsa: rtl8366: Check VLAN ID and not portsLinus Walleij2019-10-071-4/+7
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit e8521e53cca584ddf8ec4584d3c550a6c65f88c4 ] There has been some confusion between the port number and the VLAN ID in this driver. What we need to check for validity is the VLAN ID, nothing else. The current confusion came from assigning a few default VLANs for default routing and we need to rewrite that properly. Instead of checking if the port number is a valid VLAN ID, check the actual VLAN IDs passed in to the callback one by one as expected. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* vsock: Fix a lockdep warning in __vsock_release()Dexuan Cui2019-10-073-6/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 0d9138ffac24cf8b75366ede3a68c951e6dcc575 ] Lockdep is unhappy if two locks from the same class are held. Fix the below warning for hyperv and virtio sockets (vmci socket code doesn't have the issue) by using lock_sock_nested() when __vsock_release() is called recursively: ============================================ WARNING: possible recursive locking detected 5.3.0+ #1 Not tainted -------------------------------------------- server/1795 is trying to acquire lock: ffff8880c5158990 (sk_lock-AF_VSOCK){+.+.}, at: hvs_release+0x10/0x120 [hv_sock] but task is already holding lock: ffff8880c5158150 (sk_lock-AF_VSOCK){+.+.}, at: __vsock_release+0x2e/0xf0 [vsock] other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(sk_lock-AF_VSOCK); lock(sk_lock-AF_VSOCK); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by server/1795: #0: ffff8880c5d05ff8 (&sb->s_type->i_mutex_key#10){+.+.}, at: __sock_release+0x2d/0xa0 #1: ffff8880c5158150 (sk_lock-AF_VSOCK){+.+.}, at: __vsock_release+0x2e/0xf0 [vsock] stack backtrace: CPU: 5 PID: 1795 Comm: server Not tainted 5.3.0+ #1 Call Trace: dump_stack+0x67/0x90 __lock_acquire.cold.67+0xd2/0x20b lock_acquire+0xb5/0x1c0 lock_sock_nested+0x6d/0x90 hvs_release+0x10/0x120 [hv_sock] __vsock_release+0x24/0xf0 [vsock] __vsock_release+0xa0/0xf0 [vsock] vsock_release+0x12/0x30 [vsock] __sock_release+0x37/0xa0 sock_close+0x14/0x20 __fput+0xc1/0x250 task_work_run+0x98/0xc0 do_exit+0x344/0xc60 do_group_exit+0x47/0xb0 get_signal+0x15c/0xc50 do_signal+0x30/0x720 exit_to_usermode_loop+0x50/0xa0 do_syscall_64+0x24e/0x270 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f4184e85f31 Tested-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* udp: fix gso_segs calculationsJosh Hunt2019-10-072-1/+3
| | | | | | | | | | | | | | | | [ Upstream commit 44b321e5020d782ad6e8ae8183f09b163be6e6e2 ] Commit dfec0ee22c0a ("udp: Record gso_segs when supporting UDP segmentation offload") added gso_segs calculation, but incorrectly got sizeof() the pointer and not the underlying data type. In addition let's fix the v6 case. Fixes: bec1f6f69736 ("udp: generate gso with UDP_SEGMENT") Fixes: dfec0ee22c0a ("udp: Record gso_segs when supporting UDP segmentation offload") Signed-off-by: Josh Hunt <johunt@akamai.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tipc: fix unlimited bundling of small messagesTuong Lien2019-10-072-15/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e95584a889e1902fdf1ded9712e2c3c3083baf96 ] We have identified a problem with the "oversubscription" policy in the link transmission code. When small messages are transmitted, and the sending link has reached the transmit window limit, those messages will be bundled and put into the link backlog queue. However, bundles of data messages are counted at the 'CRITICAL' level, so that the counter for that level, instead of the counter for the real, bundled message's level is the one being increased. Subsequent, to-be-bundled data messages at non-CRITICAL levels continue to be tested against the unchanged counter for their own level, while contributing to an unrestrained increase at the CRITICAL backlog level. This leaves a gap in congestion control algorithm for small messages that can result in starvation for other users or a "real" CRITICAL user. Even that eventually can lead to buffer exhaustion & link reset. We fix this by keeping a 'target_bskb' buffer pointer at each levels, then when bundling, we only bundle messages at the same importance level only. This way, we know exactly how many slots a certain level have occupied in the queue, so can manage level congestion accurately. By bundling messages at the same level, we even have more benefits. Let consider this: - One socket sends 64-byte messages at the 'CRITICAL' level; - Another sends 4096-byte messages at the 'LOW' level; When a 64-byte message comes and is bundled the first time, we put the overhead of message bundle to it (+ 40-byte header, data copy, etc.) for later use, but the next message can be a 4096-byte one that cannot be bundled to the previous one. This means the last bundle carries only one payload message which is totally inefficient, as for the receiver also! Later on, another 64-byte message comes, now we make a new bundle and the same story repeats... With the new bundling algorithm, this will not happen, the 64-byte messages will be bundled together even when the 4096-byte message(s) comes in between. However, if the 4096-byte messages are sent at the same level i.e. 'CRITICAL', the bundling algorithm will again cause the same overhead. Also, the same will happen even with only one socket sending small messages at a rate close to the link transmit's one, so that, when one message is bundled, it's transmitted shortly. Then, another message comes, a new bundle is created and so on... We will solve this issue radically by another patch. Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Reported-by: Hoang Le <hoang.h.le@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sch_dsmark: fix potential NULL deref in dsmark_init()Eric Dumazet2019-10-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 474f0813a3002cb299bb73a5a93aa1f537a80ca8 ] Make sure TCA_DSMARK_INDICES was provided by the user. syzbot reported : kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 8799 Comm: syz-executor235 Not tainted 5.3.0+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:nla_get_u16 include/net/netlink.h:1501 [inline] RIP: 0010:dsmark_init net/sched/sch_dsmark.c:364 [inline] RIP: 0010:dsmark_init+0x193/0x640 net/sched/sch_dsmark.c:339 Code: 85 db 58 0f 88 7d 03 00 00 e8 e9 1a ac fb 48 8b 9d 70 ff ff ff 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 01 38 d0 7c 08 84 d2 0f 85 ca RSP: 0018:ffff88809426f3b8 EFLAGS: 00010247 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff85c6eb09 RDX: 0000000000000000 RSI: ffffffff85c6eb17 RDI: 0000000000000004 RBP: ffff88809426f4b0 R08: ffff88808c4085c0 R09: ffffed1015d26159 R10: ffffed1015d26158 R11: ffff8880ae930ac7 R12: ffff8880a7e96940 R13: dffffc0000000000 R14: ffff88809426f8c0 R15: 0000000000000000 FS: 0000000001292880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000080 CR3: 000000008ca1b000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: qdisc_create+0x4ee/0x1210 net/sched/sch_api.c:1237 tc_modify_qdisc+0x524/0x1c50 net/sched/sch_api.c:1653 rtnetlink_rcv_msg+0x463/0xb00 net/core/rtnetlink.c:5223 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5241 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x8a5/0xd60 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:657 ___sys_sendmsg+0x803/0x920 net/socket.c:2311 __sys_sendmsg+0x105/0x1d0 net/socket.c:2356 __do_sys_sendmsg net/socket.c:2365 [inline] __se_sys_sendmsg net/socket.c:2363 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2363 do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x440369 Fixes: 758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sch_cbq: validate TCA_CBQ_WRROPT to avoid crashEric Dumazet2019-10-071-14/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e9789c7cc182484fc031fd88097eb14cb26c4596 ] syzbot reported a crash in cbq_normalize_quanta() caused by an out of range cl->priority. iproute2 enforces this check, but malicious users do not. kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] SMP KASAN PTI Modules linked in: CPU: 1 PID: 26447 Comm: syz-executor.1 Not tainted 5.3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:cbq_normalize_quanta.part.0+0x1fd/0x430 net/sched/sch_cbq.c:902 RSP: 0018:ffff8801a5c333b0 EFLAGS: 00010206 RAX: 0000000020000003 RBX: 00000000fffffff8 RCX: ffffc9000712f000 RDX: 00000000000043bf RSI: ffffffff83be8962 RDI: 0000000100000018 RBP: ffff8801a5c33420 R08: 000000000000003a R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 00000000000002ef R13: ffff88018da95188 R14: dffffc0000000000 R15: 0000000000000015 FS: 00007f37d26b1700(0000) GS:ffff8801dad00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004c7cec CR3: 00000001bcd0a006 CR4: 00000000001626f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: [<ffffffff83be9d57>] cbq_normalize_quanta include/net/pkt_sched.h:27 [inline] [<ffffffff83be9d57>] cbq_addprio net/sched/sch_cbq.c:1097 [inline] [<ffffffff83be9d57>] cbq_set_wrr+0x2d7/0x450 net/sched/sch_cbq.c:1115 [<ffffffff83bee8a7>] cbq_change_class+0x987/0x225b net/sched/sch_cbq.c:1537 [<ffffffff83b96985>] tc_ctl_tclass+0x555/0xcd0 net/sched/sch_api.c:2329 [<ffffffff83a84655>] rtnetlink_rcv_msg+0x485/0xc10 net/core/rtnetlink.c:5248 [<ffffffff83cadf0a>] netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2510 [<ffffffff83a7db6d>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5266 [<ffffffff83cac2c6>] netlink_unicast_kernel net/netlink/af_netlink.c:1324 [inline] [<ffffffff83cac2c6>] netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1350 [<ffffffff83cacd4a>] netlink_sendmsg+0x89a/0xd50 net/netlink/af_netlink.c:1939 [<ffffffff8399d46e>] sock_sendmsg_nosec net/socket.c:673 [inline] [<ffffffff8399d46e>] sock_sendmsg+0x12e/0x170 net/socket.c:684 [<ffffffff8399f1fd>] ___sys_sendmsg+0x81d/0x960 net/socket.c:2359 [<ffffffff839a2d05>] __sys_sendmsg+0x105/0x1d0 net/socket.c:2397 [<ffffffff839a2df9>] SYSC_sendmsg net/socket.c:2406 [inline] [<ffffffff839a2df9>] SyS_sendmsg+0x29/0x30 net/socket.c:2404 [<ffffffff8101ccc8>] do_syscall_64+0x528/0x770 arch/x86/entry/common.c:305 [<ffffffff84400091>] entry_SYSCALL_64_after_hwframe+0x42/0xb7 Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* rxrpc: Fix rxrpc_recvmsg tracepointDavid Howells2019-10-071-1/+1
| | | | | | | | | | | | [ Upstream commit db9b2e0af605e7c994784527abfd9276cabd718a ] Fix the rxrpc_recvmsg tracepoint to handle being called with a NULL call parameter. Fixes: a25e21f0bcd2 ("rxrpc, afs: Use debug_ids rather than pointers in traces") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qmi_wwan: add support for Cinterion CLS8 devicesReinhard Speyerer2019-10-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit cf74ac6db25d4002089e85cc623ad149ecc25614 ] Add support for Cinterion CLS8 devices. Use QMI_QUIRK_SET_DTR as required for Qualcomm MDM9x07 chipsets. T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00b0 Rev= 3.18 S: Manufacturer=GEMALTO S: Product=USB Modem C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nfc: fix memory leak in llcp_sock_bind()Eric Dumazet2019-10-071-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit a0c2dc1fe63e2869b74c1c7f6a81d1745c8a695d ] sysbot reported a memory leak after a bind() has failed. While we are at it, abort the operation if kmemdup() has failed. BUG: memory leak unreferenced object 0xffff888105d83ec0 (size 32): comm "syz-executor067", pid 7207, jiffies 4294956228 (age 19.430s) hex dump (first 32 bytes): 00 69 6c 65 20 72 65 61 64 00 6e 65 74 3a 5b 34 .ile read.net:[4 30 32 36 35 33 33 30 39 37 5d 00 00 00 00 00 00 026533097]...... backtrace: [<0000000036bac473>] kmemleak_alloc_recursive /./include/linux/kmemleak.h:43 [inline] [<0000000036bac473>] slab_post_alloc_hook /mm/slab.h:522 [inline] [<0000000036bac473>] slab_alloc /mm/slab.c:3319 [inline] [<0000000036bac473>] __do_kmalloc /mm/slab.c:3653 [inline] [<0000000036bac473>] __kmalloc_track_caller+0x169/0x2d0 /mm/slab.c:3670 [<000000000cd39d07>] kmemdup+0x27/0x60 /mm/util.c:120 [<000000008e57e5fc>] kmemdup /./include/linux/string.h:432 [inline] [<000000008e57e5fc>] llcp_sock_bind+0x1b3/0x230 /net/nfc/llcp_sock.c:107 [<000000009cb0b5d3>] __sys_bind+0x11c/0x140 /net/socket.c:1647 [<00000000492c3bbc>] __do_sys_bind /net/socket.c:1658 [inline] [<00000000492c3bbc>] __se_sys_bind /net/socket.c:1656 [inline] [<00000000492c3bbc>] __x64_sys_bind+0x1e/0x30 /net/socket.c:1656 [<0000000008704b2a>] do_syscall_64+0x76/0x1a0 /arch/x86/entry/common.c:296 [<000000009f4c57a4>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: Unpublish sk from sk_reuseport_cb before call_rcuMartin KaFai Lau2019-10-071-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 8c7138b33e5c690c308b2a7085f6313fdcb3f616 ] The "reuse->sock[]" array is shared by multiple sockets. The going away sk must unpublish itself from "reuse->sock[]" before making call_rcu() call. However, this unpublish-action is currently done after a grace period and it may cause use-after-free. The fix is to move reuseport_detach_sock() to sk_destruct(). Due to the above reason, any socket with sk_reuseport_cb has to go through the rcu grace period before freeing it. It is a rather old bug (~3 yrs). The Fixes tag is not necessary the right commit but it is the one that introduced the SOCK_RCU_FREE logic and this fix is depending on it. Fixes: a4298e4522d6 ("net: add SOCK_RCU_FREE socket flag") Cc: Eric Dumazet <eric.dumazet@gmail.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: sched: taprio: Fix potential integer overflow in taprio_set_picos_per_byteVladimir Oltean2019-10-071-2/+1
| | | | | | | | | | | | | | | | | | | [ Upstream commit 68ce6688a5baefde30914fc07fc27292dbbe8320 ] The speed divisor is used in a context expecting an s64, but it is evaluated using 32-bit arithmetic. To avoid that happening, instead of multiplying by 1,000,000 in the first place, simplify the fraction and do a standard 32 bit division instead. Fixes: f04b514c0ce2 ("taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte") Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: qlogic: Fix memory leak in ql_alloc_large_buffersNavid Emamdoost2019-10-071-0/+1
| | | | | | | | | | | | [ Upstream commit 1acb8f2a7a9f10543868ddd737e37424d5c36cf4 ] In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb. This skb should be released if pci_dma_mapping_error fails. Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: ipv4: avoid mixed n_redirects and rate_tokens usagePaolo Abeni2019-10-071-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit b406472b5ad79ede8d10077f0c8f05505ace8b6d ] Since commit c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets") we use 'n_redirects' to account for redirect packets, but we still use 'rate_tokens' to compute the redirect packets exponential backoff. If the device sent to the relevant peer any ICMP error packet after sending a redirect, it will also update 'rate_token' according to the leaking bucket schema; typically 'rate_token' will raise above BITS_PER_LONG and the redirect packets backoff algorithm will produce undefined behavior. Fix the issue using 'n_redirects' to compute the exponential backoff in ip_rt_send_redirect(). Note that we still clear rate_tokens after a redirect silence period, to avoid changing an established behaviour. The root cause predates git history; before the mentioned commit in the critical scenario, the kernel stopped sending redirects, after the mentioned commit the behavior more randomic. Reported-by: Xiumei Mu <xmu@redhat.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ipv6: Handle missing host route in __ipv6_ifa_notifyDavid Ahern2019-10-071-5/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 2d819d250a1393a3e725715425ab70a0e0772a71 ] Rajendra reported a kernel panic when a link was taken down: [ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 [ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290 <snip> [ 6870.570501] Call Trace: [ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40 [ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0 [ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260 [ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430 [ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430 [ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490 [ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430 [ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0 [ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60 [ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70 [ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0 addrconf_dad_work is kicked to be scheduled when a device is brought up. There is a race between addrcond_dad_work getting scheduled and taking the rtnl lock and a process taking the link down (under rtnl). The latter removes the host route from the inet6_addr as part of addrconf_ifdown which is run for NETDEV_DOWN. The former attempts to use the host route in __ipv6_ifa_notify. If the down event removes the host route due to the race to the rtnl, then the BUG listed above occurs. Since the DAD sequence can not be aborted, add a check for the missing host route in __ipv6_ifa_notify. The only way this should happen is due to the previously mentioned race. The host route is created when the address is added to an interface; it is only removed on a down event where the address is kept. Add a warning if the host route is missing AND the device is up; this is a situation that should never happen. Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ipv6: drop incoming packets having a v4mapped source addressEric Dumazet2019-10-071-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 6af1799aaf3f1bc8defedddfa00df3192445bbf3 ] This began with a syzbot report. syzkaller was injecting IPv6 TCP SYN packets having a v4mapped source address. After an unsuccessful 4-tuple lookup, TCP creates a request socket (SYN_RECV) and calls reqsk_queue_hash_req() reqsk_queue_hash_req() calls sk_ehashfn(sk) At this point we have AF_INET6 sockets, and the heuristic used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr) For the particular spoofed packet, we end up hashing V4 addresses which were not initialized by the TCP IPv6 stack, so KMSAN fired a warning. I first fixed sk_ehashfn() to test both source and destination addresses, but then faced various problems, including user-space programs like packetdrill that had similar assumptions. Instead of trying to fix the whole ecosystem, it is better to admit that we have a dual stack behavior, and that we can not build linux kernels without V4 stack anyway. The dual stack API automatically forces the traffic to be IPv4 if v4mapped addresses are used at bind() or connect(), so it makes no sense to allow IPv6 traffic to use the same v4mapped class. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hso: fix NULL-deref on tty openJohan Hovold2019-10-071-4/+8
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 8353da9fa69722b54cba82b2ec740afd3d438748 ] Fix NULL-pointer dereference on tty open due to a failure to handle a missing interrupt-in endpoint when probing modem ports: BUG: kernel NULL pointer dereference, address: 0000000000000006 ... RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso] ... Call Trace: hso_start_serial_device+0xdc/0x140 [hso] hso_serial_open+0x118/0x1b0 [hso] tty_open+0xf1/0x490 Fixes: 542f54823614 ("tty: Modem functions for the HSO driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* erspan: remove the incorrect mtu limit for erspanHaishuang Yan2019-10-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 0e141f757b2c78c983df893e9993313e2dc21e38 ] erspan driver calls ether_setup(), after commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It causes the dev mtu of the erspan device to not be greater than 1500, this limit value is not correct for ipgre tap device. Tested: Before patch: # ip link set erspan0 mtu 1600 Error: mtu greater than device maximum. After patch: # ip link set erspan0 mtu 1600 # ip -d link show erspan0 21: erspan0@NONE: <BROADCAST,MULTICAST> mtu 1600 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 0 Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* cxgb4:Fix out-of-bounds MSI-X info array accessVishal Kulkarni2019-10-071-3/+6
| | | | | | | | | | | | | | [ Upstream commit 6b517374f4ea5a3c6e307e1219ec5f35d42e6d00 ] When fetching free MSI-X vectors for ULDs, check for the error code before accessing MSI-X info array. Otherwise, an out-of-bounds access is attempted, which results in kernel panic. Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD") Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Linux 5.2.19v5.2.19Greg Kroah-Hartman2019-10-051-1/+1
|
* platform/chrome: cros_ec_rpmsg: Fix race with host command when probe failedPi-Hsun Shih2019-10-051-4/+28
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 71cddb7097e2b0feb855d7fd7d59afd12cbee4bb ] Since the rpmsg_endpoint is created before probe is called, it's possible that a host event is received during cros_ec_register, and there would be some pending work in the host_event_work workqueue while cros_ec_register is called. If cros_ec_register fails, when the leftover work in host_event_work run, the ec_dev from the drvdata of the rpdev could be already set to NULL, causing kernel crash when trying to run cros_ec_get_next_event. Fix this by creating the rpmsg_endpoint by ourself, and when cros_ec_register fails (or on remove), destroy the endpoint first (to make sure there's no more new calls to cros_ec_rpmsg_callback), and then cancel all works in the host_event_work workqueue. Cc: stable@vger.kernel.org Fixes: 2de89fd98958 ("platform/chrome: cros_ec: Add EC host command support using rpmsg") Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* mt76: mt7615: fix mt7615 firmware path definitionsLorenzo Bianconi2019-10-052-10/+7
| | | | | | | | | | | | | | | [ Upstream commit 9d4d0d06bbf9f7e576b0ebbb2f77672d0fc7f503 ] mt7615 patch/n9/cr4 firmwares are available in mediatek folder in linux-firmware repository. Because of this mt7615 won't work on regular distributions like Ubuntu. Fix path definitions. Moreover remove useless firmware name pointers and use definitions directly Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Cc: stable@vger.kernel.org Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* mt76: mt7615: always release sem in mt7615_load_patchLorenzo Bianconi2019-10-051-3/+3
| | | | | | | | | | | [ Upstream commit 2fc446487c364bf8bbd5f8f5f27e52d914fa1d72 ] Release patch semaphore even if request_firmware fails in mt7615_load_patch Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
* md/raid0: avoid RAID0 data corruption due to layout confusion.NeilBrown2019-10-052-1/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit c84a1372df929033cb1a0441fb57bd3932f39ac9 ] If the drives in a RAID0 are not all the same size, the array is divided into zones. The first zone covers all drives, to the size of the smallest. The second zone covers all drives larger than the smallest, up to the size of the second smallest - etc. A change in Linux 3.14 unintentionally changed the layout for the second and subsequent zones. All the correct data is still stored, but each chunk may be assigned to a different device than in pre-3.14 kernels. This can lead to data corruption. It is not possible to determine what layout to use - it depends which kernel the data was written by. So we add a module parameter to allow the old (0) or new (1) layout to be specified, and refused to assemble an affected array if that parameter is not set. Fixes: 20d0189b1012 ("block: Introduce new bio_split()") cc: stable@vger.kernel.org (3.14+) Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* drm/amd/display: Restore backlight brightness after system resumeKai-Heng Feng2019-10-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | commit bb264220d9316f6bd7c1fd84b8da398c93912931 upstream. Laptops with AMD APU doesn't restore display backlight brightness after system resume. This issue started when DC was introduced. Let's use BL_CORE_SUSPENDRESUME so the backlight core calls update_status callback after system resume to restore the backlight level. Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495 (Raven Ridge). Cc: <stable@vger.kernel.org> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* CIFS: Fix oplock handling for SMB 2.1+ protocolsPavel Shilovsky2019-10-051-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | commit a016e2794fc3a245a91946038dd8f34d65e53cc3 upstream. There may be situations when a server negotiates SMB 2.1 protocol version or higher but responds to a CREATE request with an oplock rather than a lease. Currently the client doesn't handle such a case correctly: when another CREATE comes in the server sends an oplock break to the initial CREATE and the client doesn't send an ack back due to a wrong caching level being set (READ instead of RWH). Missing an oplock break ack makes the server wait until the break times out which dramatically increases the latency of the second CREATE. Fix this by properly detecting oplocks when using SMB 2.1 protocol version and higher. Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* CIFS: fix max ea value sizeMurphy Zhou2019-10-051-1/+1
| | | | | | | | | | | | | | | commit 63d37fb4ce5ae7bf1e58f906d1bf25f036fe79b2 upstream. It should not be larger then the slab max buf size. If user specifies a larger size, it passes this check and goes straightly to SMB2_set_info_init performing an insecure memcpy. Signed-off-by: Murphy Zhou <jencce.kernel@gmail.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* i2c: riic: Clear NACK in tend isrChris Brandt2019-10-051-0/+1
| | | | | | | | | | | | | | | | | | | commit a71e2ac1f32097fbb2beab098687a7a95c84543e upstream. The NACKF flag should be cleared in INTRIICNAKI interrupt processing as description in HW manual. This issue shows up quickly when PREEMPT_RT is applied and a device is probed that is not plugged in (like a touchscreen controller). The result is endless interrupts that halt system boot. Fixes: 310c18a41450 ("i2c: riic: add driver") Cc: stable@vger.kernel.org Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com> Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hwrng: core - don't wait on add_early_randomness()Laurent Vivier2019-10-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 78887832e76541f77169a24ac238fccb51059b63 upstream. add_early_randomness() is called by hwrng_register() when the hardware is added. If this hardware and its module are present at boot, and if there is no data available the boot hangs until data are available and can't be interrupted. For instance, in the case of virtio-rng, in some cases the host can be not able to provide enough entropy for all the guests. We can have two easy ways to reproduce the problem but they rely on misconfiguration of the hypervisor or the egd daemon: - if virtio-rng device is configured to connect to the egd daemon of the host but when the virtio-rng driver asks for data the daemon is not connected, - if virtio-rng device is configured to connect to the egd daemon of the host but the egd daemon doesn't provide data. The guest kernel will hang at boot until the virtio-rng driver provides enough data. To avoid that, call rng_get_data() in non-blocking mode (wait=0) from add_early_randomness(). Signed-off-by: Laurent Vivier <lvivier@redhat.com> Fixes: d9e797261933 ("hwrng: add randomness to system from rng...") Cc: <stable@vger.kernel.org> Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* quota: fix wrong condition in is_quota_modification()Chao Yu2019-10-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 6565c182094f69e4ffdece337d395eb7ec760efc upstream. Quoted from commit 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize") " At LSF we decided that if we truncate up from isize we shouldn't trim fallocated blocks that were fallocated with KEEP_SIZE and are past the new i_size. This patch fixes ext4 to do this. " And generic/092 of fstest have covered this case for long time, however is_quota_modification() didn't adjust based on that rule, so that in below condition, we will lose to quota block change: - fallocate blocks beyond EOF - remount - truncate(file_path, file_size) Fix it. Link: https://lore.kernel.org/r/20190911093650.35329-1-yuchao0@huawei.com Fixes: 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize") CC: stable@vger.kernel.org Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-17 19:32:17 +0000