summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* powerpc/idle: Don't corrupt back chain when going idleMichael Ellerman2021-10-271-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 496c5fe25c377ddb7815c4ce8ecfb676f051e9b6 upstream. In isa206_idle_insn_mayloss() we store various registers into the stack red zone, which is allowed. However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again, to 0(r1), which corrupts the stack back chain. We used to do the same in isa206_idle_insn_mayloss() itself, but we fixed that in 73287caa9210 ("powerpc64/idle: Fix SP offsets when saving GPRs"), however we missed that the macro also corrupts the back chain. Corrupting the back chain is bad for debuggability but doesn't necessarily cause a bug. However we recently changed the stack handling in some KVM code, and it now relies on the stack back chain being valid when it returns. The corruption causes that code to return with r1 pointing somewhere in kernel data, at some point LR is restored from the stack and we branch to NULL or somewhere else invalid. Only affects Power8 hosts running KVM guests, with dynamic_mt_modes enabled (which it is by default). The fixes tag below points to the commit that changed the KVM stack handling, exposing this bug. The actual corruption of the back chain has always existed since 948cf67c4726 ("powerpc: Add NAP mode support on Power7 in HV mode"). Fixes: 9b4416c5095c ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* KVM: PPC: Book3S HV: Make idle_kvm_start_guest() return 0 if it went to guestMichael Ellerman2021-10-271-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit cdeb5d7d890e14f3b70e8087e745c4a6a7d9f337 upstream. We call idle_kvm_start_guest() from power7_offline() if the thread has been requested to enter KVM. We pass it the SRR1 value that was returned from power7_idle_insn() which tells us what sort of wakeup we're processing. Depending on the SRR1 value we pass in, the KVM code might enter the guest, or it might return to us to do some host action if the wakeup requires it. If idle_kvm_start_guest() is able to handle the wakeup, and enter the guest it is supposed to indicate that by returning a zero SRR1 value to us. That was the behaviour prior to commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C"), however in that commit the handling of SRR1 was reworked, and the zeroing behaviour was lost. Returning from idle_kvm_start_guest() without zeroing the SRR1 value can confuse the host offline code, causing the guest to crash and other weirdness. Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C") Cc: stable@vger.kernel.org # v5.2+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211015133929.832061-2-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()Michael Ellerman2021-10-271-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 9b4416c5095c20e110c82ae602c254099b83b72f upstream. In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C") kvm_start_guest() became idle_kvm_start_guest(). The old code allocated a stack frame on the emergency stack, but didn't use the frame to store anything, and also didn't store anything in its caller's frame. idle_kvm_start_guest() on the other hand is written more like a normal C function, it creates a frame on entry, and also stores CR/LR into its callers frame (per the ABI). The problem is that there is no caller frame on the emergency stack. The emergency stack for a given CPU is allocated with: paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE; So emergency_sp actually points to the first address above the emergency stack allocation for a given CPU, we must not store above it without first decrementing it to create a frame. This is different to the regular kernel stack, paca->kstack, which is initialised to point at an initial frame that is ready to use. idle_kvm_start_guest() stores the backchain, CR and LR all of which write outside the allocation for the emergency stack. It then creates a stack frame and saves the non-volatile registers. Unfortunately the frame it creates is not large enough to fit the non-volatiles, and so the saving of the non-volatile registers also writes outside the emergency stack allocation. The end result is that we corrupt whatever is at 0-24 bytes, and 112-248 bytes above the emergency stack allocation. In practice this has gone unnoticed because the memory immediately above the emergency stack happens to be used for other stack allocations, either another CPUs mc_emergency_sp or an IRQ stack. See the order of calls to irqstack_early_init() and emergency_stack_init(). The low addresses of another stack are the top of that stack, and so are only used if that stack is under extreme pressue, which essentially never happens in practice - and if it did there's a high likelyhood we'd crash due to that stack overflowing. Still, we shouldn't be corrupting someone else's stack, and it is purely luck that we aren't corrupting something else. To fix it we save CR/LR into the caller's frame using the existing r1 on entry, we then create a SWITCH_FRAME_SIZE frame (which has space for pt_regs) on the emergency stack with the backchain pointing to the existing stack, and then finally we switch to the new frame on the emergency stack. Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C") Cc: stable@vger.kernel.org # v5.2+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211015133929.832061-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* powerpc64/idle: Fix SP offsets when saving GPRsChristopher M. Riedl2021-10-271-65/+73
| | | | | | | | | | | | | | | | | | commit 73287caa9210ded6066833195f4335f7f688a46b upstream. The idle entry/exit code saves/restores GPRs in the stack "red zone" (Protected Zone according to PowerPC64 ELF ABI v2). However, the offset used for the first GPR is incorrect and overwrites the back chain - the Protected Zone actually starts below the current SP. In practice this is probably not an issue, but it's still incorrect so fix it. Also expand the comments to explain why using the stack "red zone" instead of creating a new stackframe is appropriate here. Signed-off-by: Christopher M. Riedl <cmr@codefail.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210206072342.5067-1-cmr@codefail.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* audit: fix possible null-pointer dereference in audit_filter_rulesGaosheng Cui2021-10-271-1/+1
| | | | | | | | | | | | | | | | commit 6e3ee990c90494561921c756481d0e2125d8b895 upstream. Fix possible null-pointer dereference in audit_filter_rules. audit_filter_rules() error: we previously assumed 'ctx' could be null Cc: stable@vger.kernel.org Fixes: bf361231c295 ("audit: add saddr_fam filter field") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ASoC: DAPM: Fix missing kctl change notificationsTakashi Iwai2021-10-271-5/+8
| | | | | | | | | | | | | | | | | | | commit 5af82c81b2c49cfb1cad84d9eb6eab0e3d1c4842 upstream. The put callback of a kcontrol is supposed to return 1 when the value is changed, and this will be notified to user-space. However, some DAPM kcontrols always return 0 (except for errors), hence the user-space misses the update of a control value. This patch corrects the behavior by properly returning 1 when the value gets updated. Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ALSA: hda/realtek: Add quirk for Clevo PC50HSSteven Clarkson2021-10-271-0/+1
| | | | | | | | | | | | | commit aef454b40288158b850aab13e3d2a8c406779401 upstream. Apply existing PCI quirk to the Clevo PC50HS and related models to fix audio output on the built in speakers. Signed-off-by: Steven Clarkson <sc@lambdal.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211014133554.1326741-1-sc@lambdal.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ALSA: usb-audio: Provide quirk for Sennheiser GSP670 HeadsetBrendan Grieve2021-10-271-0/+32
| | | | | | | | | | | | | | | | | | | commit 3c414eb65c294719a91a746260085363413f91c1 upstream. As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13 The GSP670 has 2 playback and 1 recording device that by default are detected in an incompatible order for alsa. This may have been done to make it compatible for the console by the manufacturer and only affects the latest firmware which uses its own ID. This quirk will resolve this by reordering the channels. Signed-off-by: Brendan Grieve <brendan@grieve.com.au> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211015025335.196592-1-brendan@grieve.com.au Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* vfs: check fd has read access in kernel_read_file_from_fd()Matthew Wilcox (Oracle)2021-10-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 032146cda85566abcd1c4884d9d23e4e30a07e9a upstream. If we open a file without read access and then pass the fd to a syscall whose implementation calls kernel_read_file_from_fd(), we get a warning from __kernel_read(): if (WARN_ON_ONCE(!(file->f_mode & FMODE_READ))) This currently affects both finit_module() and kexec_file_load(), but it could affect other syscalls in the future. Link: https://lkml.kernel.org/r/20211007220110.600005-1-willy@infradead.org Fixes: b844f0ecbc56 ("vfs: define kernel_copy_file_from_fd()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reported-by: Hao Sun <sunhao.th@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Mimi Zohar <zohar@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* elfcore: correct reference to CONFIG_UMLLukas Bulwahn2021-10-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit b0e901280d9860a0a35055f220e8e457f300f40a upstream. Commit 6e7b64b9dd6d ("elfcore: fix building with clang") introduces special handling for two architectures, ia64 and User Mode Linux. However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig symbol for User-Mode Linux was used. Although the directory for User Mode Linux is ./arch/um; the Kconfig symbol for this architecture is called CONFIG_UML. Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs: UM Referencing files: include/linux/elfcore.h Similar symbols: UML, NUMA Correct the name of the config to the intended one. [akpm@linux-foundation.org: fix um/x86_64, per Catalin] Link: https://lkml.kernel.org/r/20211006181119.2851441-1-catalin.marinas@arm.com Link: https://lkml.kernel.org/r/YV6pejGzLy5ppEpt@arm.com Link: https://lkml.kernel.org/r/20211006082209.417-1-lukas.bulwahn@gmail.com Fixes: 6e7b64b9dd6d ("elfcore: fix building with clang") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Barret Rhoden <brho@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ocfs2: mount fails with buffer overflow in strlenValentin Vidic2021-10-271-4/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit b15fa9224e6e1239414525d8d556d824701849fc upstream. Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the trace below. Problem seems to be that strings for cluster stack and cluster name are not guaranteed to be null terminated in the disk representation, while strlcpy assumes that the source string is always null terminated. This causes a read outside of the source string triggering the buffer overflow detection. detected buffer overflow in strlen ------------[ cut here ]------------ kernel BUG at lib/string.c:1149! invalid opcode: 0000 [#1] SMP PTI CPU: 1 PID: 910 Comm: mount.ocfs2 Not tainted 5.14.0-1-amd64 #1 Debian 5.14.6-2 RIP: 0010:fortify_panic+0xf/0x11 ... Call Trace: ocfs2_initialize_super.isra.0.cold+0xc/0x18 [ocfs2] ocfs2_fill_super+0x359/0x19b0 [ocfs2] mount_bdev+0x185/0x1b0 legacy_get_tree+0x27/0x40 vfs_get_tree+0x25/0xb0 path_mount+0x454/0xa20 __x64_sys_mount+0x103/0x140 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae Link: https://lkml.kernel.org/r/20210929180654.32460-1-vvidic@valentin-vidic.from.hr Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ocfs2: fix data corruption after conversion from inline formatJan Kara2021-10-271-34/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5314454ea3ff6fc746eaf71b9a7ceebed52888fa upstream. Commit 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") uncovered a latent bug in ocfs2 conversion from inline inode format to a normal inode format. The code in ocfs2_convert_inline_data_to_extents() attempts to zero out the whole cluster allocated for file data by grabbing, zeroing, and dirtying all pages covering this cluster. However these pages are beyond i_size, thus writeback code generally ignores these dirty pages and no blocks were ever actually zeroed on the disk. This oversight was fixed by commit 693c241a5f6a ("ocfs2: No need to zero pages past i_size.") for standard ocfs2 write path, inline conversion path was apparently forgotten; the commit log also has a reasoning why the zeroing actually is not needed. After commit 6dbf7bb55598, things became worse as writeback code stopped invalidating buffers on pages beyond i_size and thus these pages end up with clean PageDirty bit but with buffers attached to these pages being still dirty. So when a file is converted from inline format, then writeback triggers, and then the file is grown so that these pages become valid, the invalid dirtiness state is preserved, mark_buffer_dirty() does nothing on these pages (buffers are already dirty) but page is never written back because it is clean. So data written to these pages is lost once pages are reclaimed. Simple reproducer for the problem is: xfs_io -f -c "pwrite 0 2000" -c "pwrite 2000 2000" -c "fsync" \ -c "pwrite 4000 2000" ocfs2_file After unmounting and mounting the fs again, you can observe that end of 'ocfs2_file' has lost its contents. Fix the problem by not doing the pointless zeroing during conversion from inline format similarly as in the standard write path. [akpm@linux-foundation.org: fix whitespace, per Joseph] Link: https://lkml.kernel.org/r/20210930095405.21433-1-jack@suse.cz Fixes: 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com> Acked-by: Gang He <ghe@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: "Markov, Andrey" <Markov.Andrey@Dell.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ceph: fix handling of "meta" errorsJeff Layton2021-10-275-27/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 1bd85aa65d0e7b5e4d09240f492f37c569fdd431 upstream. Currently, we check the wb_err too early for directories, before all of the unsafe child requests have been waited on. In order to fix that we need to check the mapping->wb_err later nearer to the end of ceph_fsync. We also have an overly-complex method for tracking errors after blocklisting. The errors recorded in cleanup_session_requests go to a completely separate field in the inode, but we end up reporting them the same way we would for any other error (in fsync). There's no real benefit to tracking these errors in two different places, since the only reporting mechanism for them is in fsync, and we'd need to advance them both every time. Given that, we can just remove i_meta_err, and convert the places that used it to instead just use mapping->wb_err instead. That also fixes the original problem by ensuring that we do a check_and_advance of the wb_err at the end of the fsync op. Cc: stable@vger.kernel.org URL: https://tracker.ceph.com/issues/52864 Reported-by: Patrick Donnelly <pdonnell@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: j1939: j1939_xtp_rx_rts_session_new(): abort TP less than 9 bytesZhang Changzhong2021-10-272-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | commit a4fbe70c5cb746441d56b28cf88161d9e0e25378 upstream. The receiver should abort TP if 'total message size' in TP.CM_RTS and TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the j1939 stack only checks the upper bound and the receiver will accept the following broadcast message: vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01 vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00 vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF This patch adds check for the lower bound and abort illegal TP. [1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: j1939: j1939_xtp_rx_dat_one(): cancel session if receive TP.DT with ↵Zhang Changzhong2021-10-271-2/+5
| | | | | | | | | | | | | | | | | error length commit 379743985ab6cfe2cbd32067cf4ed497baca6d06 upstream. According to SAE-J1939-21, the data length of TP.DT must be 8 bytes, so cancel session when receive unexpected TP.DT message. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1632972800-45091-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: j1939: j1939_netdev_start(): fix UAF for rx_kref of j1939_privZiyang Xuan2021-10-271-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit d9d52a3ebd284882f5562c88e55991add5d01586 upstream. It will trigger UAF for rx_kref of j1939_priv as following. cpu0 cpu1 j1939_sk_bind(socket0, ndev0, ...) j1939_netdev_start j1939_sk_bind(socket1, ndev0, ...) j1939_netdev_start j1939_priv_set j1939_priv_get_by_ndev_locked j1939_jsk_add ..... j1939_netdev_stop kref_put_lock(&priv->rx_kref, ...) kref_get(&priv->rx_kref, ...) REFCOUNT_WARN("addition on 0;...") ==================================================== refcount_t: addition on 0; use-after-free. WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0 RIP: 0010:refcount_warn_saturate+0x169/0x1e0 Call Trace: j1939_netdev_start+0x68b/0x920 j1939_sk_bind+0x426/0xeb0 ? security_socket_bind+0x83/0xb0 The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to protect. Fixes: 9d71dd0c70099 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210926104757.2021540-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Reported-by: syzbot+85d9878b19c94f9019ad@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: j1939: j1939_tp_rxtimer(): fix errant alert in j1939_tp_rxtimerZiyang Xuan2021-10-271-3/+2
| | | | | | | | | | | | | | | | | | | | | commit b504a884f6b5a77dac7d580ffa08e482f70d1a30 upstream. When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will give an alert "rx timeout, send abort", but do nothing actually. Move the alert into session active judgment condition, it is more reasonable. One of the scenarios is that j1939_tp_rxtimer() execute followed by j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: peak_pci: peak_pci_remove(): fix UAFZheyu Ma2021-10-271-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 949fe9b35570361bc6ee2652f89a0561b26eec98 upstream. When remove the module peek_pci, referencing 'chan' again after releasing 'dev' will cause UAF. Fix this by releasing 'dev' later. The following log reveals it: [ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537 [ 35.965513 ] Call Trace: [ 35.965718 ] dump_stack_lvl+0xa8/0xd1 [ 35.966028 ] print_address_description+0x87/0x3b0 [ 35.966420 ] kasan_report+0x172/0x1c0 [ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170 [ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967945 ] __asan_report_load8_noabort+0x14/0x20 [ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.968752 ] pci_device_remove+0xa9/0x250 Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: peak_usb: pcan_usb_fd_decode_status(): fix back to ERROR_ACTIVE state ↵Stephane Grosjean2021-10-271-3/+2
| | | | | | | | | | | | | | | | notification commit 3d031abc7e7249573148871180c28ecedb5e27df upstream. This corrects the lack of notification of a return to ERROR_ACTIVE state for USB - CANFD devices from PEAK-System. Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com Cc: stable@vger.kernel.org Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: rcar_can: fix suspend/resumeYoshihiro Shimoda2021-10-271-8/+12
| | | | | | | | | | | | | | | | | commit f7c05c3987dcfde9a4e8c2d533db013fabebca0d upstream. If the driver was not opened, rcar_can_suspend() should not call clk_disable() because the clock was not enabled. Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver") Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com Cc: stable@vger.kernel.org Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Tested-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: enetc: fix ethtool counter name for PM0_TERRVladimir Oltean2021-10-271-1/+1
| | | | | | | | | | | | | | | [ Upstream commit fb8dc5fc8cbdfd62ecd16493848aee2f42ed84d9 ] There are two counters named "MAC tx frames", one of them is actually incorrect. The correct name for that counter should be "MAC tx error frames", which is symmetric to the existing "MAC rx error frames". Fixes: 16eb4c85c964 ("enetc: Add ethtool statistics") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: stmmac: Fix E2E delay mechanismKurt Kanzenbach2021-10-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3cb958027cb8b78d3ee639ce9af54c2ef1bf964f ] When utilizing End to End delay mechanism, the following error messages show up: |root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m |ptp4l[950.573]: selected /dev/ptp3 as PTP clock |ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1 |ptp4l[956.879]: selected best master clock 001395.fffe.4897b4 |ptp4l[956.879]: port 1: assuming the grand master role |ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER |ptp4l[962.017]: port 1: received DELAY_REQ without timestamp |ptp4l[962.273]: port 1: received DELAY_REQ without timestamp |ptp4l[963.090]: port 1: received DELAY_REQ without timestamp Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") already addresses this problem for the dwmac v5.10. However, same holds true for all dwmacs above version v4.10. Correct the check accordingly. Afterwards everything works as expected. Tested on Intel Atom(R) x6414RE Processor. Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2") Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: hns3: disable sriov before unload hclge layerPeng Li2021-10-273-0/+23
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 0dd8a25f355b4df2d41c08df1716340854c7d4c5 ] HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko. hns3.ko includes network stack and pci_driver, hclge.ko includes HW device action, algo_ops and timer task, hnae3.ko includes some register function. When SRIOV is enable and hclge.ko is removed, HW device is unloaded but VF still exists, PF will not reply VF mbx messages, and cause errors. This patch fix it by disable SRIOV before remove hclge.ko. Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: hns3: add limit ets dwrr bandwidth cannot be 0Guangbin Huang2021-10-271-0/+9
| | | | | | | | | | | | | | | [ Upstream commit 731797fdffa3d083db536e2fdd07ceb050bb40b1 ] If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP mode. In this case, this tc may occupy all the tx bandwidth if it has huge traffic, so it violates the purpose of the user setting. To fix this problem, limit the ets dwrr bandwidth must greater than 0. Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: hns3: reset DWRR of unused tc to zeroGuangbin Huang2021-10-271-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit b63fcaab959807282e9822e659034edf95fc8bd1 ] Currently, DWRR of tc will be initialized to a fixed value when this tc is enabled, but it is not been reset to 0 when this tc is disabled. It cause a problem that the DWRR of unused tc is not 0 after using tc tool to add and delete multi-tc parameters. For examples, after enabling 4 TCs and restoring to 1 TC by follow tc commands: $ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \ 8@0 8@8 8@16 8@24 hw 1 mode channel $ tc qdisc del dev eth0 root Now there is just one TC is enabled for eth0, but the tc info querying by debugfs is shown as follow: $ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info enabled tc number: 1 weight_offset: 14 TC MODE WEIGHT 0 dwrr 100 1 dwrr 100 2 dwrr 100 3 dwrr 100 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 This patch fixes it by resetting DWRR of tc to 0 when tc is disabled. Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* NIOS2: irqflags: rename a redefined register nameRandy Dunlap2021-10-272-3/+3
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 4cce60f15c04d69eff6ffc539ab09137dbe15070 ] Both arch/nios2/ and drivers/mmc/host/tmio_mmc.c define a macro with the name "CTL_STATUS". Change the one in arch/nios2/ to be "CTL_FSTATUS" (flags status) to eliminate the build warning. In file included from ../drivers/mmc/host/tmio_mmc.c:22: drivers/mmc/host/tmio_mmc.h:31: warning: "CTL_STATUS" redefined 31 | #define CTL_STATUS 0x1c arch/nios2/include/asm/registers.h:14: note: this is the location of the previous definition 14 | #define CTL_STATUS 0 Fixes: b31ebd8055ea ("nios2: Nios2 registers") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: dsa: lantiq_gswip: fix register definitionAleksander Jan Bajkowski2021-10-271-1/+1
| | | | | | | | | | | | | | [ Upstream commit 66d262804a2276721eac86cf18fcd61046149193 ] I compared the register definitions with the D-Link DWR-966 GPL sources and found that the PUAFD field definition was incorrect. This definition is unused and causes no issues. Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* lan78xx: select CRC32Vegard Nossum2021-10-271-0/+1
| | | | | | | | | | | | | | | | | [ Upstream commit 46393d61a328d7c4e3264252dae891921126c674 ] Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast': lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le' The actual use of crc32_le() comes indirectly through ether_crc(). Fixes: 55d7de9de6c30 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* netfilter: ipvs: make global sysctl readonly in non-init netnsAntoine Tenart2021-10-271-0/+5
| | | | | | | | | | | | | [ Upstream commit 174c376278949c44aad89c514a6b5db6cee8db59 ] Because the data pointer of net/ipv4/vs/debug_level is not updated per netns, it must be marked as read-only in non-init netns. Fixes: c6d2d445d8de ("IPVS: netns, final patch enabling network name space.") Signed-off-by: Antoine Tenart <atenart@kernel.org> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ASoC: wm8960: Fix clock configuration on slave modeShengjiu Wang2021-10-271-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 6b9b546dc00797c74bef491668ce5431ff54e1e2 ] There is a noise issue for 8kHz sample rate on slave mode. Compared with master mode, the difference is the DACDIV setting, after correcting the DACDIV, the noise is gone. There is no noise issue for 48kHz sample rate, because the default value of DACDIV is correct for 48kHz. So wm8960_configure_clocking() should be functional for ADC and DAC function even if it is slave mode. In order to be compatible for old use case, just add condition for checking that sysclk is zero with slave mode. Fixes: 0e50b51aa22f ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* dma-debug: fix sg checks in debug_dma_map_sg()Gerald Schaefer2021-10-271-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 293d92cbbd2418ca2ba43fed07f1b92e884d1c77 ] The following warning occurred sporadically on s390: DMA-API: nvme 0006:00:00.0: device driver maps memory from kernel text or rodata [addr=0000000048cc5e2f] [len=131072] WARNING: CPU: 4 PID: 825 at kernel/dma/debug.c:1083 check_for_illegal_area+0xa8/0x138 It is a false-positive warning, due to broken logic in debug_dma_map_sg(). check_for_illegal_area() checks for overlay of sg elements with kernel text or rodata. It is called with sg_dma_len(s) instead of s->length as parameter. After the call to ->map_sg(), sg_dma_len() will contain the length of possibly combined sg elements in the DMA address space, and not the individual sg element length, which would be s->length. The check will then use the physical start address of an sg element, and add the DMA length for the overlap check, which could result in the false warning, because the DMA length can be larger than the actual single sg element length. In addition, the call to check_for_illegal_area() happens in the iteration over mapped_ents, which will not include all individual sg elements if any of them were combined in ->map_sg(). Fix this by using s->length instead of sg_dma_len(s). Also put the call to check_for_illegal_area() in a separate loop, iterating over all the individual sg elements ("nents" instead of "mapped_ents"). While at it, as suggested by Robin Murphy, also move check_for_stack() inside the new loop, as it is similarly concerned with validating the individual sg elements. Link: https://lore.kernel.org/lkml/20210705185252.4074653-1-gerald.schaefer@linux.ibm.com Fixes: 884d05970bfb ("dma-debug: use sg_dma_len accessor") Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
* NFSD: Keep existing listeners on portlist errorBenjamin Coddington2021-10-271-1/+4
| | | | | | | | | | | | | | | [ Upstream commit c20106944eb679fa3ab7e686fe5f6ba30fbc51e5 ] If nfsd has existing listening sockets without any processes, then an error returned from svc_create_xprt() for an additional transport will remove those existing listeners. We're seeing this in practice when userspace attempts to create rpcrdma transports without having the rpcrdma modules present before creating nfsd kernel processes. Fix this by checking for existing sockets before calling nfsd_destroy(). Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* xtensa: xtfpga: Try software restart before simulating CPU resetGuenter Roeck2021-10-271-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 012e974501a270d8dfd4ee2039e1fdf7579c907e ] Rebooting xtensa images loaded with the '-kernel' option in qemu does not work. When executing a reboot command, the qemu session either hangs or experiences an endless sequence of error messages. Kernel panic - not syncing: Unrecoverable error in exception handler Reset code jumps to the CPU restart address, but Linux can not recover from there because code and data in the kernel init sections have been discarded and overwritten at this point. XTFPGA platforms have a means to reset the CPU by writing 0xdead into a specific FPGA IO address. When used in QEMU the kernel image loaded with the '-kernel' option gets restored to its original state allowing the machine to boot successfully. Use that mechanism to attempt a platform reset. If it does not work, fall back to the existing mechanism. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* xtensa: xtfpga: use CONFIG_USE_OF instead of CONFIG_OFMax Filippov2021-10-271-2/+2
| | | | | | | | | | | [ Upstream commit f3d7c2cdf6dc0d5402ec29c3673893b3542c5ad1 ] Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not selected but CONFIG_OF is. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ARM: dts: at91: sama5d2_som1_ek: disable ISC node by defaultEugen Hristev2021-10-271-1/+0
| | | | | | | | | | | | | | [ Upstream commit 4348cc10da6377a86940beb20ad357933b8f91bb ] Without a sensor node, the ISC will simply fail to probe, as the corresponding port node is missing. It is then logical to disable the node in the devicetree. If we add a port with a connection to a sensor endpoint, ISC can be enabled. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210902121358.503589-1-eugen.hristev@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* tee: optee: Fix missing devices unregister during optee_removeSumit Garg2021-10-273-0/+26
| | | | | | | | | | | | | | | | commit 7f565d0ead264329749c0da488de9c8dfa2f18ce upstream. When OP-TEE driver is built as a module, OP-TEE client devices registered on TEE bus during probe should be unregistered during optee_remove. So implement optee_unregister_devices() accordingly. Fixes: c3fa24af9244 ("tee: optee: add TEE bus device enumeration support") Reported-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> [SG: backport to 5.4, dev name s/optee-ta/optee-clnt/] Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: switchdev: do not propagate bridge updates across bridgesRussell King2021-10-271-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | commit 07c6f9805f12f1bb538ef165a092b300350384aa upstream. When configuring a tree of independent bridges, propagating changes from the upper bridge across a bridge master to the lower bridge ports brings surprises. For example, a lower bridge may have vlan filtering enabled. It may have a vlan interface attached to the bridge master, which may then be incorporated into another bridge. As soon as the lower bridge vlan interface is attached to the upper bridge, the lower bridge has vlan filtering disabled. This occurs because switchdev recursively applies its changes to all lower devices no matter what. Reviewed-by: Ido Schimmel <idosch@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Fabian Bläse <fabian@blaese.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* parisc: math-emu: Fix fall-through warningsHelge Deller2021-10-271-3/+53
| | | | | | | | | | commit 6f1fce595b78b775d7fb585c15c2dc3a6994f96e upstream. Fix lots of fallthrough warnings, e.g.: arch/parisc/math-emu/fpudispatch.c:323:33: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Linux 5.4.155v5.4.155Greg Kroah-Hartman2021-10-201-1/+1
| | | | | | | | | | | | | Link: https://lore.kernel.org/r/20211018132329.453964125@linuxfoundation.org Link: https://lore.kernel.org/r/20211018143049.664480980@linuxfoundation.org Tested-by: Shuah Khan <skhan@linuxfoundation.org> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Hulk Robot <hulkrobot@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ionic: don't remove netdev->dev_addr when syncing uc listShannon Nelson2021-10-201-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | commit 5c976a56570f29aaf4a2f9a1bf99789c252183c9 upstream. Bridging, and possibly other upper stack gizmos, adds the lower device's netdev->dev_addr to its own uc list, and then requests it be deleted when the upper bridge device is removed. This delete request also happens with the bridging vlan_filtering is enabled and then disabled. Bonding has a similar behavior with the uc list, but since it also uses set_mac to manage netdev->dev_addr, it doesn't have the same the failure case. Because we store our netdev->dev_addr in our uc list, we need to ignore the delete request from dev_uc_sync so as to not lose the address and all hope of communicating. Note that ndo_set_mac_address is expressly changing netdev->dev_addr, so no limitation is set there. Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* r8152: select CRC32 and CRYPTO/CRYPTO_HASH/CRYPTO_SHA256Vegard Nossum2021-10-201-0/+4
| | | | | | | | | | | | | | | | | | | | commit 9973a43012b6ad1720dbc4d5faf5302c28635b8c upstream. Fix the following build/link errors by adding a dependency on CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32: ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum': r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash' ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest' ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm' ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode': r8152.c:(.text+0xdcb0): undefined reference to `crc32_le' Fixes: 9370f2d05a2a1 ("r8152: support request_firmware for RTL8153") Fixes: ac718b69301c7 ("net/usb: new driver for RTL8152") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qed: Fix missing error code in qed_slowpath_start()chongjiapeng2021-10-201-0/+1
| | | | | | | | | | | | | | | | | | commit a5a14ea7b4e55604acb0dc9d88fdb4cb6945bc77 upstream. The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'rc'. Eliminate the follow smatch warning: drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start() warn: missing error code 'rc'. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mqprio: Correct stats in mqprio_dump_class_stats().Sebastian Andrzej Siewior2021-10-201-12/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 14132690860e4d06aa3e1c4d7d8e9866ba7756dd upstream. Introduction of lockless subqueues broke the class statistics. Before the change stats were accumulated in `bstats' and `qstats' on the stack which was then copied to struct gnet_dump. After the change the `bstats' and `qstats' are initialized to 0 and never updated, yet still fed to gnet_dump. The code updates the global qdisc->cpu_bstats and qdisc->cpu_qstats instead, clobbering them. Most likely a copy-paste error from the code in mqprio_dump(). __gnet_stats_copy_basic() and __gnet_stats_copy_queue() accumulate the values for per-CPU case but for global stats they overwrite the value, so only stats from the last loop iteration / tc end up in sch->[bq]stats. Use the on-stack [bq]stats variables again and add the stats manually in the global case. Fixes: ce679e8df7ed2 ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio") Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> https://lore.kernel.org/all/20211007175000.2334713-2-bigeasy@linutronix.de/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* acpi/arm64: fix next_platform_timer() section mismatch errorJackie Liu2021-10-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 596143e3aec35c93508d6b7a05ddc999ee209b61 upstream. Fix modpost Section mismatch error in next_platform_timer(). [...] WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc The function next_platform_timer() references the variable __initdata acpi_gtdt_desc. This is often because next_platform_timer lacks a __initdata annotation or the annotation of acpi_gtdt_desc is wrong. WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc The function next_platform_timer() references the variable __initdata acpi_gtdt_desc. This is often because next_platform_timer lacks a __initdata annotation or the annotation of acpi_gtdt_desc is wrong. ERROR: modpost: Section mismatches detected. Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them. make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1 make[1]: *** Deleting file 'vmlinux.symvers' make: *** [Makefile:1176: vmlinux] Error 2 [...] Fixes: a712c3ed9b8a ("acpi/arm64: Add memory-mapped timer support in GTDT driver") Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Acked-by: Hanjun Guo <guohanjun@huawei.com> Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/msm/dsi: fix off by one in dsi_bus_clk_enable error handlingDan Carpenter2021-10-201-1/+1
| | | | | | | | | | | | | | | commit c8f01ffc83923a91e8087aaa077de13354a7aa59 upstream. This disables a lock which wasn't enabled and it does not disable the first lock in the array. Fixes: 6e0eb52eba9e ("drm/msm/dsi: Parse bus clocks from a list") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20211001123409.GG2283@kili Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()Dan Carpenter2021-10-201-1/+3
| | | | | | | | | | | | | | | commit 739b4e7756d3301dd673ca517afca46a5f635562 upstream. Return an error code if msm_dsi_manager_validate_current_config(). Don't return success. Fixes: 8b03ad30e314 ("drm/msm/dsi: Use one connector for dual DSI mode") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20211001123308.GF2283@kili Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/msm: Fix null pointer dereference on pointer edpColin Ian King2021-10-201-1/+2
| | | | | | | | | | | | | | | | | commit 2133c4fc8e1348dcb752f267a143fe2254613b34 upstream. The initialization of pointer dev dereferences pointer edp before edp is null checked, so there is a potential null pointer deference issue. Fix this by only dereferencing edp after edp has been null checked. Addresses-Coverity: ("Dereference before null check") Fixes: ab5b0107ccf3 ("drm/msm: Initial add eDP support in msm drm driver (v5)") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210929121857.213922-1-colin.king@canonical.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drm/panel: olimex-lcd-olinuxino: select CRC32Vegard Nossum2021-10-201-0/+1
| | | | | | | | | | | | | | | | | | commit a14bc107edd0c108bda2245e50daa22f91c95d20 upstream. Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/gpu/drm/panel/panel-olimex-lcd-olinuxino.o: in function `lcd_olinuxino_probe': panel-olimex-lcd-olinuxino.c:(.text+0x303): undefined reference to `crc32_le' Fixes: 17fd7a9d324fd ("drm/panel: Add support for Olimex LCD-OLinuXino panel") Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211012115242.10325-1-vegard.nossum@oracle.com Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() callVadim Pasternak2021-10-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 9b024201693e397441668cca0d2df7055fe572eb upstream. Change kstrtou32() argument 'base' to be zero instead of 'len'. It works by chance for setting one bit value, but it is not supposed to work in case value passed to mlxreg_io_attr_store() is greater than 1. It works for example, for: echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable But it will fail for: echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable, where n > 1. The flow for input buffer conversion is as below: _kstrtoull(const char *s, unsigned int base, unsigned long long *res) calls: rv = _parse_integer(s, base, &_res); For the second case, where n > 1: - _parse_integer() converts 's' to 'val'. For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3 'len' is set to 3 (string buffer 0x33 0x0a), etcetera. - 'base' is equal or greater then '2' (length of input buffer). As a result, _parse_integer() exits with result zero (rv): rv = 0; while (1) { ... if (val >= base)-> (2 >= 2) break; ... rv++; ... } And _kstrtoull() in their turn will fail: if (rv == 0) return -EINVAL; Fixes: 5ec4a8ace06c ("platform/mellanox: Introduce support for Mellanox register access driver") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20210927142214.2613929-2-vadimp@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mlxsw: thermal: Fix out-of-bounds memory accessesIdo Schimmel2021-10-201-47/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 332fdf951df8b870e3da86b122ae304e2aabe88c upstream. Currently, mlxsw allows cooling states to be set above the maximum cooling state supported by the driver: # cat /sys/class/thermal/thermal_zone2/cdev0/type mlxsw_fan # cat /sys/class/thermal/thermal_zone2/cdev0/max_state 10 # echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state # echo $? 0 This results in out-of-bounds memory accesses when thermal state transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the transition table is accessed with a too large index (state) [1]. According to the thermal maintainer, it is the responsibility of the driver to reject such operations [2]. Therefore, return an error when the state to be set exceeds the maximum cooling state supported by the driver. To avoid dead code, as suggested by the thermal maintainer [3], partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") that tried to interpret these invalid cooling states (above the maximum) in a special way. The cooling levels array is not removed in order to prevent the fans going below 20% PWM, which would cause them to get stuck at 0% PWM. [1] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290 Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122 Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016 Workqueue: events_freezable_power_ thermal_zone_device_check Call Trace: dump_stack_lvl+0x8b/0xb3 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b thermal_cooling_device_stats_update+0x271/0x290 __thermal_cdev_update+0x15e/0x4e0 thermal_cdev_update+0x9f/0xe0 step_wise_throttle+0x770/0xee0 thermal_zone_device_update+0x3f6/0xdf0 process_one_work+0xa42/0x1770 worker_thread+0x62f/0x13e0 kthread+0x3ee/0x4e0 ret_from_fork+0x1f/0x30 Allocated by task 1: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 thermal_cooling_device_setup_sysfs+0x153/0x2c0 __thermal_cooling_device_register.part.0+0x25b/0x9c0 thermal_cooling_device_register+0xb3/0x100 mlxsw_thermal_init+0x5c5/0x7e0 __mlxsw_core_bus_device_register+0xcb3/0x19c0 mlxsw_core_bus_device_register+0x56/0xb0 mlxsw_pci_probe+0x54f/0x710 local_pci_probe+0xc6/0x170 pci_device_probe+0x2b2/0x4d0 really_probe+0x293/0xd10 __driver_probe_device+0x2af/0x440 driver_probe_device+0x51/0x1e0 __driver_attach+0x21b/0x530 bus_for_each_dev+0x14c/0x1d0 bus_add_driver+0x3ac/0x650 driver_register+0x241/0x3d0 mlxsw_sp_module_init+0xa2/0x174 do_one_initcall+0xee/0x5f0 kernel_init_freeable+0x45a/0x4de kernel_init+0x1f/0x210 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff8881052f7800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 1016 bytes inside of 1024-byte region [ffff8881052f7800, ffff8881052f7c00) The buggy address belongs to the page: page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0 head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x200000000010200(slab|head|node=0|zone=2) raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/ [3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/ CC: Daniel Lezcano <daniel.lezcano@linaro.org> Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone") Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-04-15 08:34:10 +0000