| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.4, round 2
Highlights:
-----------
Fixes for STM32MP157:
-Fix CAN RAM mapping
-Change stmfx pinctrl definition for joystick and camera. Due to
stmfx pinctrl fix done in v5.4-rc cycle, camera and joystick were no
longer functional.
* tag 'stm32-dt-for-v5.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
Link: https://lore.kernel.org/r/d316b81f-a8d7-e9be-fe3c-73a242e7d941@st.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Fixes: a502b343ebd0 ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Fixes: a502b343ebd0 ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Split the 10Kbytes CAN message RAM to be able to use simultaneously
FDCAN1 and FDCAN2 instances.
First 5Kbytes are allocated to FDCAN1 and last 5Kbytes are used for
FDCAN2. To do so, set the offset to 0x1400 in mram-cfg for FDCAN2.
Fixes: d44d6e021301 ("ARM: dts: stm32: change CAN RAM mapping on stm32mp157c")
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Relax qspi pins slew-rate to minimize peak currents.
Fixes: 844030057339 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
One fix for the A83t powerdown, and one for the TBS A711 tablet wifi suspend
* tag 'sunxi-fixes-for-5.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
Link: https://lore.kernel.org/r/3935640c-289c-40b2-b156-79787aed8c60.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
PRCM_PWROFF_GATING_REG has CPU0 at bit 4 on A83T. So without this
patch, instead of gating the CPU0, the whole cluster was power gated,
when shutting down first CPU in the cluster.
Fixes: 6961275e72a8c1 ("ARM: sun8i: smp: Add support for A83T")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Without enabling keep-power-in-suspend, we can't wake the device
up using WOL packet, and the log is flooded with these messages
on resume:
sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command
sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command
So to make the WiFi really a wakeup-source, we need to keep it powered
during suspend.
Fixes: 0e23372080def7 ("arm: dts: sun8i: Add the TBS A711 tablet devicetree")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 2nd round:
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da5d ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
* tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
Link: https://lore.kernel.org/r/20191029110334.GA20928@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The baseboard of the Logic PD i.MX6 development kit has a power
button routed which can both power down and power up the board.
It can also wake the board from sleep. This functionality was
marked as disabled by default in imx6qdl.dtsi, so it needs to
be explicitly enabled for each board.
This patch enables the snvs power key again.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Cc: stable <stable@vger.kernel.org> #5.3+
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
a storm of accelerometer interrupts is seen:
[ 114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[ 114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[ 114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[ 114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[ 114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[ 114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[ 114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[ 114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[ 114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[ 114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[ 114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[ 114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[ 114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[ 114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[ 114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[ 114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[ 114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[ 114.368830] 1f00: 20000013 ffffffff
[ 114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[ 114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[ 114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[ 114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[ 114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[ 114.411958] handlers:
[ 114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[ 114.422974] Disabling IRQ #260
CPU0 CPU1
....
260: 100001 0 gpio-mxc 31 Level mma8451
The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.
The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.
The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.
Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.
Fixes: a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |\| | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Relax qspi pins slew-rate to minimize peak currents.
Fixes: 844030057339 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board")
Link: https://lore.kernel.org/r/20191025130122.11407-1-alexandre.torgue@st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Three fixes for omaps for v5.4-rc cycle
Two regression fixes for omap3 iommu. I missed applying two omap3
related iommu pdata quirks patches earlier because the kbuild test
robot produced errors on them for missing dependencies.
Fix ti-sysc interconnect target module driver handling for watchdog
quirk. I must have tested this earlier only with watchdog service
running, but clearly it does not do what it needs to do.
* tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
Link: https://lore.kernel.org/r/pull-1571848757-282222@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The OMAP3 ISP IOMMU does not have any reset lines, so it didn't
need any pdata previously. The OMAP IOMMU driver now requires the
platform data ops for device_enable/idle on all the IOMMU devices
after commit db8918f61d51 ("iommu/omap: streamline enable/disable
through runtime pm callbacks") to enable/disable the clocks properly
and maintain the reference count and the omap_hwmod state machine.
So, add these callbacks through iommu pdata quirks for the OMAP3
ISP IOMMU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The OMAP IOMMU driver requires the device_enable/idle platform
data ops on all the IOMMU devices to be able to enable and disable
the clocks after commit db8918f61d51 ("iommu/omap: streamline
enable/disable through runtime pm callbacks"). Plug in these
pdata ops for all the existing IOMMUs through pdata quirks to
maintain functionality.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | |\ \ \ \ \
| | | |_|/ /
| | |/| | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Fixes: d2b9c6444301 ("ARM: dts: sun7i: Add CSI0 controller")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
* tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
Link: https://lore.kernel.org/r/20191021194302.21024-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
bcm2835-rpi.dtsi defines the behavior of the ACT LED, which is available
on all Raspberry Pi boards. But there is no driver for this particual
GPIO on CM3 in mainline yet, so this node was left incomplete without
the actual GPIO definition. Since commit 025bf37725f1 ("gpio: Fix return
value mismatch of function gpiod_get_from_of_node()") this causing probe
issues of the leds-gpio driver for users of the CM3 dtsi file.
leds-gpio: probe of leds failed with error -2
Until we have the necessary GPIO driver hide the ACT node for CM3
to avoid this.
Reported-by: Fredrik Yhlen <fredrik.yhlen@endian.se>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Fixes: a54fe8a6cf66 ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| | |\| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.4, please pull the following:
- Stefan fixes the MMC controller bus-width property for the Raspberry Pi
Zero Wireless which was incorrect after a prior refactoring
* tag 'arm-soc/for-5.4/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
Link: https://lore.kernel.org/r/20191015172356.9650-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The commit e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at board level")
Reported-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci fixes for v5.4
======================
* fix GPIO backlight support on DA850 by enabling the needed config
in davinci_all_defconfig. This is a fix because the driver and board
support got converted to use BACKLIGHT_GPIO driver, but defconfig update
is still missing in v5.4.
* fix for McBSP DMA on DM365
* tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
Link: https://lore.kernel.org/r/7f3393f9-59be-a2d4-c1e1-ba6e407681d1@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
DA850 EVM has been converted to use GPIO backlight device
for display backlight GPIO control.
Enable the GPIO backlight module in davinci_all_defconfig
to keep backlight support working.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: edits to commit message for context]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
dm365 have only single McBSP, so the device name is without .0
Fixes: 0c750e1fe481d ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | |\ \ \ \
| | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Since commit 2eba69071b4b ("drm/msm: Remove Kconfig default") the
CONFIG_DRM_MSM option is no longer selected by default on i.MX5.
Explicitly select CONFIG_DRM_MSM so that we can get GPU support
by default on i.MX51 and i.MX53.
Fixes: 2eba69071b4b ("drm/msm: Remove Kconfig default")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the
board, since both are connected to the same parent bus and all of
their children have the same I2C address.
Fixes: ca4b4d373fcc ("ARM: dts: vf610: Add ZII SCU4 AIB board")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Jeff White <jeff.white@zii.aero>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| | |\ \ \
| | | |/
| | |/|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |\ \ |
|
| | | | |/
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Commit 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea15 ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea15 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
According to
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt,
i2c-mux-idle-disconnect is a property of a parent node since it
pertains to the mux/switch as a whole, so move it there and drop all
of the concurrences in child nodes.
Fixes: d031773169df ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07d8 ("ARM: dts: Configure sgx for omap5")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | |\ \ |
|
| | | | |/
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The old omapdrm panels got removed for v5.4 in favor of generic panels,
and the Kconfig options changed. Let's update omap2plus_defconfig
accordingly so the same panels are still enabled.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
:Pull ARM fixes from Russell King:
- fix for alignment faults under high memory pressure
- use u32 for ARM instructions in fault handler
- mark functions that must always be inlined with __always_inline
- fix for nommu XIP
- fix ARMv7M switch to handler mode in reboot path
- fix the recently introduced AMBA reset control error paths
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8926/1: v7m: remove register save to stack before svc
ARM: 8914/1: NOMMU: Fix exc_ret for XIP
ARM: 8908/1: add __always_inline to functions called from __get_user_check()
ARM: mm: alignment: use "u32" for 32-bit instructions
ARM: mm: fix alignment handler faults under memory pressure
drivers/amba: fix reset control error handling
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
r0-r3 & r12 registers are saved & restored, before & after svc
respectively. Intention was to preserve those registers across thread to
handler mode switch.
On v7-M, hardware saves the register context upon exception in AAPCS
complaint way. Restoring r0-r3 & r12 is done from stack location where
hardware saves it, not from the location on stack where these registers
were saved.
To clarify, on stm32f429 discovery board:
1. before svc, sp - 0x90009ff8
2. r0-r3,r12 saved to 0x90009ff8 - 0x9000a00b
3. upon svc, h/w decrements sp by 32 & pushes registers onto stack
4. after svc, sp - 0x90009fd8
5. r0-r3,r12 restored from 0x90009fd8 - 0x90009feb
Above means r0-r3,r12 is not restored from the location where they are
saved, but since hardware pushes the registers onto stack, the registers
are restored correctly.
Note that during register saving to stack (step 2), it goes past
0x9000a000. And it seems, based on objdump, there are global symbols
residing there, and it perhaps can cause issues on a non-XIP Kernel
(on XIP, data section is setup later).
Based on the analysis above, manually saving registers onto stack is at
best no-op and at worst can cause data section corruption. Hence remove
storing of registers onto stack before svc.
Fixes: b70cd406d7fe ("ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode")
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
It was reported that 72cd4064fcca "NOMMU: Toggle only bits in
EXC_RETURN we are really care of" breaks NOMMU+XIP combination.
It happens because saved EXC_RETURN gets overwritten when data
section is relocated.
The fix is to propagate EXC_RETURN via register and let relocation
code to commit that value into memory.
Fixes: 72cd4064fcca ("ARM: 8830/1: NOMMU: Toggle only bits in EXC_RETURN we are really care of")
Reported-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
KernelCI reports that bcm2835_defconfig is no longer booting since
commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") (https://lkml.org/lkml/2019/9/26/825).
I also received a regression report from Nicolas Saenz Julienne
(https://lkml.org/lkml/2019/9/27/263).
This problem has cropped up on bcm2835_defconfig because it enables
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler tends to prefer not inlining
functions with -Os. I was able to reproduce it with other boards and
defconfig files by manually enabling CONFIG_CC_OPTIMIZE_FOR_SIZE.
The __get_user_check() specifically uses r0, r1, r2 registers.
So, uaccess_save_and_enable() and uaccess_restore() must be inlined.
Otherwise, those register assignments would be entirely dropped,
according to my analysis of the disassembly.
Prior to commit 9012d011660e ("compiler: allow all arches to enable
CONFIG_OPTIMIZE_INLINING"), the 'inline' marker was always enough for
inlining functions, except on x86.
Since that commit, all architectures can enable CONFIG_OPTIMIZE_INLINING.
So, __always_inline is now the only guaranteed way of forcible inlining.
I added __always_inline to 4 functions in the call-graph from the
__get_user_check() macro.
Fixes: 9012d011660e ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Rather than using "unsigned long", use "u32" for 32-bit instructions in
the alignment fault handler.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When the system has high memory pressure, the page containing the
instruction may be paged out. Using probe_kernel_address() means that
if the page is swapped out, the resulting page fault will not be
handled because page faults are disabled by this function.
Use get_user() to read the instruction instead.
Reported-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Fixes: b255188f90e2 ("ARM: fix scheduling while atomic warning in alignment handling code")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
* Removes mediatek,physpeed property from dtsi that is useless in PHYLINK
* Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
* Set gmac1 to gmii mode that connect to a internal gphy
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
