| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
| |
so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
| |
|
|
|
|
|
|
| |
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
This patch adds board support for ATNGW100 mkII. This board is an upgrade of
the ATNGW100 where the difference is an additional 256 MB NAND flash device and
128 MB 32-bit SDRAM instead of the 32 MB 16-bit SDRAM on ATNGW100.
Tested on ATNGW100 mkII, duh (-:
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch will adjust the setup the DMA controller for the AC97
Controller in the at32ap700x machine code. This setup matches the new
ALSA driver for the AC97C.
The struct ac97c_platform_data has been moved into its own header file
located in the sound include path.
Tested on ATSTK1006 + ATSTK1000.
This patch will setup the AC97 controller properly for the adjusted
machine code. Both EVKLCD10x and Hammerhead board has been updated.
Tested on EVKLCD10x, and copied to Hammerhead board.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold with board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
| |
|
|
|
|
|
|
| |
This patch adjusts the timing parameters for the Kyocera LCD panels
connected on the EVKLCD10X addon boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
The PB15 GPIO line is used to control the enable and disable signal for
the backlight regulator on EVKLCD10x boards. This patch hands the I/O
line over to the LCDC driver, which will control when to enable and
disable the backlight.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: reverted ac97c change]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
| |
|
|
|
|
|
|
| |
This patch will set the pin mask to alternative 18 bits per pixel output
for EVKLCD10x boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
This patch lets the user enable support for EVKLCD100 and EVKLCD101
(refered to by EVKLCD10X). By enabling EVKLCD10X support the LCD
controller and AC97 controller platform devices are added.
The user can also choose between the EVKLCD100 (QVGA display) and the
EVKLCD101 (VGA display), this is added to automagically select the
correct panel timing and resolution parameters.
Enabling support for EVKLCD10X addon board will cripple the MCI platform
device a bit since they share two GPIO lines (detect and write-protect).
These two lines are disabled when EVKLCD10X is enabled.
The default configurations are based upon ATNGW100, but with added AC97C
and LCDC driver. Virtual terminal is also enabled by default for
EVKLCD10X boards.
Verified on hardware with a NGW100 + EVKLCD100/101.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
