summaryrefslogtreecommitdiffstats
path: root/arch/x86/kernel/apic
Commit message (Collapse)AuthorAgeFilesLines
* x86/apic: Soft disable APIC before initializing itThomas Gleixner2019-10-051-0/+8
| | | | | | | | | | | | | | | | | [ Upstream commit 2640da4cccf5cc613bf26f0998b9e340f4b5f69c ] If the APIC was already enabled on entry of setup_local_APIC() then disabling it soft via the SPIV register makes a lot of sense. That masks all LVT entries and brings it into a well defined state. Otherwise previously enabled LVTs which are not touched in the setup function stay unmasked and might surprise the just booting kernel. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190722105219.068290579@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
* x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machinesThomas Gleixner2019-09-211-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3e5bedc2c258341702ddffbd7688c5e6eb01eafa ] Rahul Tanwar reported the following bug on DT systems: > 'ioapic_dynirq_base' contains the virtual IRQ base number. Presently, it is > updated to the end of hardware IRQ numbers but this is done only when IOAPIC > configuration type is IOAPIC_DOMAIN_LEGACY or IOAPIC_DOMAIN_STRICT. There is > a third type IOAPIC_DOMAIN_DYNAMIC which applies when IOAPIC configuration > comes from devicetree. > > See dtb_add_ioapic() in arch/x86/kernel/devicetree.c > > In case of IOAPIC_DOMAIN_DYNAMIC (DT/OF based system), 'ioapic_dynirq_base' > remains to zero initialized value. This means that for OF based systems, > virtual IRQ base will get set to zero. Such systems will very likely not even boot. For DT enabled machines ioapic_dynirq_base is irrelevant and not updated, so simply map the IRQ base 1:1 instead. Reported-by: Rahul Tanwar <rahul.tanwar@linux.intel.com> Tested-by: Rahul Tanwar <rahul.tanwar@linux.intel.com> Tested-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: alan@linux.intel.com Cc: bp@alien8.de Cc: cheol.yong.kim@intel.com Cc: qi-ming.wu@intel.com Cc: rahul.tanwar@intel.com Cc: rppt@linux.ibm.com Cc: tony.luck@intel.com Link: http://lkml.kernel.org/r/20190821081330.1187-1-rahul.tanwar@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* Revert "x86/apic: Include the LDR when clearing out APIC registers"Linus Torvalds2019-09-101-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 950b07c14e8c59444e2359f15fd70ed5112e11a0 ] This reverts commit 558682b5291937a70748d36fd9ba757fb25b99ae. Chris Wilson reports that it breaks his CPU hotplug test scripts. In particular, it breaks offlining and then re-onlining the boot CPU, which we treat specially (and the BIOS does too). The symptoms are that we can offline the CPU, but it then does not come back online again: smpboot: CPU 0 is now offline smpboot: Booting Node 0 Processor 0 APIC 0x0 smpboot: do_boot_cpu failed(-1) to wakeup CPU#0 Thomas says he knows why it's broken (my personal suspicion: our magic handling of the "cpu0_logical_apicid" thing), but for 5.3 the right fix is to just revert it, since we've never touched the LDR bits before, and it's not worth the risk to do anything else at this stage. [ Hotpluging of the boot CPU is special anyway, and should be off by default. See the "BOOTPARAM_HOTPLUG_CPU0" config option and the cpu0_hotplug kernel parameter. In general you should not do it, and it has various known limitations (hibernate and suspend require the boot CPU, for example). But it should work, even if the boot CPU is special and needs careful treatment - Linus ] Link: https://lore.kernel.org/lkml/156785100521.13300.14461504732265570003@skylake-alporthouse-com/ Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Bandan Das <bsd@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* x86/apic: Include the LDR when clearing out APIC registersBandan Das2019-09-061-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 558682b5291937a70748d36fd9ba757fb25b99ae upstream. Although APIC initialization will typically clear out the LDR before setting it, the APIC cleanup code should reset the LDR. This was discovered with a 32-bit KVM guest jumping into a kdump kernel. The stale bits in the LDR triggered a bug in the KVM APIC implementation which caused the destination mapping for VCPUs to be corrupted. Note that this isn't intended to paper over the KVM APIC bug. The kernel has to clear the LDR when resetting the APIC registers except when X2APIC is enabled. This lacks a Fixes tag because missing to clear LDR goes way back into pre git history. [ tglx: Made x2apic_enabled a function call as required ] Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190826101513.5080-3-bsd@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Do not initialize LDR and DFR for bigsmpBandan Das2019-09-061-22/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit bae3a8d3308ee69a7dbdf145911b18dfda8ade0d upstream. Legacy apic init uses bigsmp for smp systems with 8 and more CPUs. The bigsmp APIC implementation uses physical destination mode, but it nevertheless initializes LDR and DFR. The LDR even ends up incorrectly with multiple bit being set. This does not cause a functional problem because LDR and DFR are ignored when physical destination mode is active, but it triggered a problem on a 32-bit KVM guest which jumps into a kdump kernel. The multiple bits set unearthed a bug in the KVM APIC implementation. The code which creates the logical destination map for VCPUs ignores the disabled state of the APIC and ends up overwriting an existing valid entry and as a result, APIC calibration hangs in the guest during kdump initialization. Remove the bogus LDR/DFR initialization. This is not intended to work around the KVM APIC bug. The LDR/DFR ininitalization is wrong on its own. The issue goes back into the pre git history. The fixes tag is the commit in the bitkeeper import which introduced bigsmp support in 2003. git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Fixes: db7b9e9f26b8 ("[PATCH] Clustered APIC setup for >8 CPU systems") Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190826101513.5080-2-bsd@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Handle missing global clockevent gracefullyThomas Gleixner2019-08-291-15/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit f897e60a12f0b9146357780d317879bce2a877dc upstream. Some newer machines do not advertise legacy timers. The kernel can handle that situation if the TSC and the CPU frequency are enumerated by CPUID or MSRs and the CPU supports TSC deadline timer. If the CPU does not support TSC deadline timer the local APIC timer frequency has to be known as well. Some Ryzens machines do not advertize legacy timers, but there is no reliable way to determine the bus frequency which feeds the local APIC timer when the machine allows overclocking of that frequency. As there is no legacy timer the local APIC timer calibration crashes due to a NULL pointer dereference when accessing the not installed global clock event device. Switch the calibration loop to a non interrupt based one, which polls either TSC (if frequency is known) or jiffies. The latter requires a global clockevent. As the machines which do not have a global clockevent installed have a known TSC frequency this is a non issue. For older machines where TSC frequency is not known, there is no known case where the legacy timers do not exist as that would have been reported long ago. Reported-by: Daniel Drake <drake@endlessm.com> Reported-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Daniel Drake <drake@endlessm.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908091443030.21433@nanos.tec.linutronix.de Link: http://bugzilla.opensuse.org/show_bug.cgi?id=1142926#c12 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Silence -Wtype-limits compiler warningsQian Cai2019-08-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit ec6335586953b0df32f83ef696002063090c7aef ] There are many compiler warnings like this, In file included from ./arch/x86/include/asm/smp.h:13, from ./arch/x86/include/asm/mmzone_64.h:11, from ./arch/x86/include/asm/mmzone.h:5, from ./include/linux/mmzone.h:969, from ./include/linux/gfp.h:6, from ./include/linux/mm.h:10, from arch/x86/kernel/apic/io_apic.c:34: arch/x86/kernel/apic/io_apic.c: In function 'check_timer': ./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits] if ((v) <= apic_verbosity) \ ^~ arch/x86/kernel/apic/io_apic.c:2160:2: note: in expansion of macro 'apic_printk' apic_printk(APIC_QUIET, KERN_INFO "..TIMER: vector=0x%02X " ^~~~~~~~~~~ ./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits] if ((v) <= apic_verbosity) \ ^~ arch/x86/kernel/apic/io_apic.c:2207:4: note: in expansion of macro 'apic_printk' apic_printk(APIC_QUIET, KERN_ERR "..MP-BIOS bug: " ^~~~~~~~~~~ APIC_QUIET is 0, so silence them by making apic_verbosity type int. Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1562621805-24789-1-git-send-email-cai@lca.pw Signed-off-by: Sasha Levin <sashal@kernel.org>
* x86/smp: fix non-SMP broken build due to redefinition of ↵Vlastimil Babka2018-08-151-0/+2
| | | | | | | | | | | | | | | | | | | apic_id_is_primary_thread commit d0055f351e647f33f3b0329bff022213bf8aa085 upstream. The function has an inline "return false;" definition with CONFIG_SMP=n but the "real" definition is also visible leading to "redefinition of ‘apic_id_is_primary_thread’" compiler error. Guard it with #ifdef CONFIG_SMP Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Fixes: 6a4d2657e048 ("x86/smp: Provide topology_is_primary_thread()") Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86: Don't include linux/irq.h from asm/hardirq.hNicolai Stange2018-08-155-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 447ae316670230d7d29430e2cbf1f5db4f49d14c upstream The next patch in this series will have to make the definition of irq_cpustat_t available to entering_irq(). Inclusion of asm/hardirq.h into asm/apic.h would cause circular header dependencies like asm/smp.h asm/apic.h asm/hardirq.h linux/irq.h linux/topology.h linux/smp.h asm/smp.h or linux/gfp.h linux/mmzone.h asm/mmzone.h asm/mmzone_64.h asm/smp.h asm/apic.h asm/hardirq.h linux/irq.h linux/irqdesc.h linux/kobject.h linux/sysfs.h linux/kernfs.h linux/idr.h linux/gfp.h and others. This causes compilation errors because of the header guards becoming effective in the second inclusion: symbols/macros that had been defined before wouldn't be available to intermediate headers in the #include chain anymore. A possible workaround would be to move the definition of irq_cpustat_t into its own header and include that from both, asm/hardirq.h and asm/apic.h. However, this wouldn't solve the real problem, namely asm/harirq.h unnecessarily pulling in all the linux/irq.h cruft: nothing in asm/hardirq.h itself requires it. Also, note that there are some other archs, like e.g. arm64, which don't have that #include in their asm/hardirq.h. Remove the linux/irq.h #include from x86' asm/hardirq.h. Fix resulting compilation errors by adding appropriate #includes to *.c files as needed. Note that some of these *.c files could be cleaned up a bit wrt. to their set of #includes, but that should better be done from separate patches, if at all. Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "x86/apic: Ignore secondary threads if nosmt=force"Thomas Gleixner2018-08-151-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 506a66f374891ff08e064a058c446b336c5ac760 upstream Dave Hansen reported, that it's outright dangerous to keep SMT siblings disabled completely so they are stuck in the BIOS and wait for SIPI. The reason is that Machine Check Exceptions are broadcasted to siblings and the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or reboots the machine. The MCE chapter in the SDM contains the following blurb: Because the logical processors within a physical package are tightly coupled with respect to shared hardware resources, both logical processors are notified of machine check errors that occur within a given physical processor. If machine-check exceptions are enabled when a fatal error is reported, all the logical processors within a physical package are dispatched to the machine-check exception handler. If machine-check exceptions are disabled, the logical processors enter the shutdown state and assert the IERR# signal. When enabling machine-check exceptions, the MCE flag in control register CR4 should be set for each logical processor. Reverting the commit which ignores siblings at enumeration time solves only half of the problem. The core cpuhotplug logic needs to be adjusted as well. This thoughtful engineered mechanism also turns the boot process on all Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU before the secondary CPUs are brought up. Depending on the number of physical cores the window in which this situation can happen is smaller or larger. On a HSW-EX it's about 750ms: MCE is enabled on the boot CPU: [ 0.244017] mce: CPU supports 22 MCE banks The corresponding sibling #72 boots: [ 1.008005] .... node #0, CPUs: #72 That means if an MCE hits on physical core 0 (logical CPUs 0 and 72) between these two points the machine is going to shutdown. At least it's a known safe state. It's obvious that the early boot can be hit by an MCE as well and then runs into the same situation because MCEs are not yet enabled on the boot CPU. But after enabling them on the boot CPU, it does not make any sense to prevent the kernel from recovering. Adjust the nosmt kernel parameter documentation as well. Reverts: 2207def700f9 ("x86/apic: Ignore secondary threads if nosmt=force") Reported-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Ignore secondary threads if nosmt=forceThomas Gleixner2018-08-151-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2207def700f902f169fc237b717252c326f9e464 upstream nosmt on the kernel command line merely prevents the onlining of the secondary SMT siblings. nosmt=force makes the APIC detection code ignore the secondary SMT siblings completely, so they even do not show up as possible CPUs. That reduces the amount of memory allocations for per cpu variables and saves other resources from being allocated too large. This is not fully equivalent to disabling SMT in the BIOS because the low level SMT enabling in the BIOS can result in partitioning of resources between the siblings, which is not undone by just ignoring them. Some CPUs can use the full resources when their sibling is not onlined, but this is depending on the CPU family and model and it's not well documented whether this applies to all partitioned resources. That means depending on the workload disabling SMT in the BIOS might result in better performance. Linus analysis of the Intel manual: The intel optimization manual is not very clear on what the partitioning rules are. I find: "In general, the buffers for staging instructions between major pipe stages are partitioned. These buffers include µop queues after the execution trace cache, the queues after the register rename stage, the reorder buffer which stages instructions for retirement, and the load and store buffers. In the case of load and store buffers, partitioning also provided an easier implementation to maintain memory ordering for each logical processor and detect memory ordering violations" but some of that partitioning may be relaxed if the HT thread is "not active": "In Intel microarchitecture code name Sandy Bridge, the micro-op queue is statically partitioned to provide 28 entries for each logical processor, irrespective of software executing in single thread or multiple threads. If one logical processor is not active in Intel microarchitecture code name Ivy Bridge, then a single thread executing on that processor core can use the 56 entries in the micro-op queue" but I do not know what "not active" means, and how dynamic it is. Some of that partitioning may be entirely static and depend on the early BIOS disabling of HT, and even if we park the cores, the resources will just be wasted. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/smp: Provide topology_is_primary_thread()Thomas Gleixner2018-08-151-0/+15
| | | | | | | | | | | | | | | | | | | commit 6a4d2657e048f096c7ffcad254010bd94891c8c0 upstream If the CPU is supporting SMT then the primary thread can be found by checking the lower APIC ID bits for zero. smp_num_siblings is used to build the mask for the APIC ID bits which need to be taken into account. This uses the MPTABLE or ACPI/MADT supplied APIC ID, which can be different than the initial APIC ID in CPUID. But according to AMD the lower bits have to be consistent. Intel gave a tentative confirmation as well. Preparatory patch to support disabling SMT at boot/runtime. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Future-proof the TSC_DEADLINE quirk for SKXLen Brown2018-08-061-0/+3
| | | | | | | | | | | | | | | | | | | | | commit d9e6dbcf28f383bf08e6a3180972f5722e514a54 upstream. All SKX with stepping higher than 4 support the TSC_DEADLINE, no matter the microcode version. Without this patch, upcoming SKX steppings will not be able to use their TSC_DEADLINE timer. Signed-off-by: Len Brown <len.brown@intel.com> Cc: <stable@kernel.org> # v4.14+ Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 616dd5872e ("x86/apic: Update TSC_DEADLINE quirk with additional SKX stepping") Link: http://lkml.kernel.org/r/d0c7129e509660be9ec6b233284b8d42d90659e8.1532207856.git.len.brown@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Set up through-local-APIC mode on the boot CPU if 'noapic' specifiedBaoquan He2018-05-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit bee3204ec3c49f6f53add9c3962c9012a5c036fa ] Currently the kdump kernel becomes very slow if 'noapic' is specified. Normal kernel doesn't have this bug. Kernel parameter 'noapic' is used to disable IO-APIC in system for testing or special purpose. Here the root cause is that in kdump kernel LAPIC is disabled since commit: 522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC") In this case we need set up through-local-APIC on boot CPU in setup_local_APIC(). In normal kernel the legacy irq mode is enabled by the BIOS. If it is virtual wire mode, the local-APIC has been enabled and set as through-local-APIC. Though we fixed the regression introduced by commit 522e664644, to further improve robustness set up the through-local-APIC mode explicitly, do not rely on the default boot IRQ mode. Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: douly.fnst@cn.fujitsu.com Cc: joro@8bytes.org Cc: prarit@redhat.com Cc: uobergfe@redhat.com Link: http://lkml.kernel.org/r/20180214054656.3780-7-bhe@redhat.com [ Rewrote the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/platform/UV: Fix GAM Range Table entries less than 1GBmike.travis@hpe.com2018-04-261-3/+12
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit c25d99d20ba69824a1e2cc118e04b877cd427afc ] The latest UV platforms include the new ApachePass NVDIMMs into the UV address space. This has introduced address ranges in the Global Address Map Table that are less than the previous lowest range, which was 2GB. Fix the address calculation so it accommodates address ranges from bytes to exabytes. Signed-off-by: Mike Travis <mike.travis@hpe.com> Reviewed-by: Andrew Banman <andrew.banman@hpe.com> Reviewed-by: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Russ Anderson <russ.anderson@hpe.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180205221503.190219903@stormcage.americas.sgi.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_steppingJia Zhang2018-02-221-3/+3
| | | | | | | | | | | | | | | | | | | | | commit b399151cb48db30ad1e0e93dd40d68c6d007b637 upstream. x86_mask is a confusing name which is hard to associate with the processor's stepping. Additionally, correct an indent issue in lib/cpu.c. Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com> [ Updated it to more recent kernels. ] Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: tony.luck@intel.com Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic/vector: Fix off by one in error pathThomas Gleixner2018-01-231-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 45d55e7bac4028af93f5fa324e69958a0b868e96 upstream. Keith reported the following warning: WARNING: CPU: 28 PID: 1420 at kernel/irq/matrix.c:222 irq_matrix_remove_managed+0x10f/0x120 x86_vector_free_irqs+0xa1/0x180 x86_vector_alloc_irqs+0x1e4/0x3a0 msi_domain_alloc+0x62/0x130 The reason for this is that if the vector allocation fails the error handling code tries to free the failed vector as well, which causes the above imbalance warning to trigger. Adjust the error path to handle this correctly. Fixes: b5dc8e6c21e7 ("x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors") Reported-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Keith Busch <keith.busch@intel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801161217300.1823@nanos Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/virt, x86/platform: Merge 'struct x86_hyper' into 'struct x86_platform' ↵Juergen Gross2017-12-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | and 'struct x86_init' commit f72e38e8ec8869ac0ba5a75d7d2f897d98a1454e upstream. Instead of x86_hyper being either NULL on bare metal or a pointer to a struct hypervisor_x86 in case of the kernel running as a guest merge the struct into x86_platform and x86_init. This will remove the need for wrappers making it hard to find out what is being called. With dummy functions added for all callbacks testing for a NULL function pointer can be removed, too. Suggested-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Juergen Gross <jgross@suse.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: akataria@vmware.com Cc: boris.ostrovsky@oracle.com Cc: devel@linuxdriverproject.org Cc: haiyangz@microsoft.com Cc: kvm@vger.kernel.org Cc: kys@microsoft.com Cc: pbonzini@redhat.com Cc: rkrcmar@redhat.com Cc: rusty@rustcorp.com.au Cc: sthemmin@microsoft.com Cc: virtualization@lists.linux-foundation.org Cc: xen-devel@lists.xenproject.org Link: http://lkml.kernel.org/r/20171109132739.23465-2-jgross@suse.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/platform/UV: Convert timers to use timer_setup()Kees Cook2017-12-251-3/+2
| | | | | | | | | | | | | | | | | commit 376f3bcebdc999cc737d9052109cc33b573b3a8b upstream. In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dimitri Sivanich <sivanich@hpe.com> Cc: Russ Anderson <rja@hpe.com> Cc: Mike Travis <mike.travis@hpe.com> Link: https://lkml.kernel.org/r/20171016232231.GA100493@beast Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-028-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* x86/apic: Update TSC_DEADLINE quirk with additional SKX steppingLen Brown2017-10-121-1/+11
| | | | | | | | | | | | | | | SKX stepping-3 fixed the TSC_DEADLINE issue in a different ucode version number than stepping-4. Linux needs to know this stepping-3 specific version number to also enable the TSC_DEADLINE on stepping-3. The steppings and ucode versions are documented in the SKX BIOS update: https://downloadmirror.intel.com/26978/eng/ReleaseNotes_R00.01.0004.txt Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Link: https://lkml.kernel.org/r/60f2bbf7cf617e212b522e663f84225bfebc50e5.1507756305.git.len.brown@intel.com
* x86/apic: Silence "FW_BUG TSC_DEADLINE disabled due to Errata" on hypervisorsPaolo Bonzini2017-10-121-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 594a30fb1242 ("x86/apic: Silence "FW_BUG TSC_DEADLINE disabled due to Errata" on CPUs without the feature", 2017-08-30) was also about silencing the warning on VirtualBox; however, KVM does expose the TSC deadline timer, and it's virtualized so that it is immune from CPU errata. Therefore, booting 4.13 with "-cpu Haswell" shows this in the logs: [ 0.000000] [Firmware Bug]: TSC_DEADLINE disabled due to Errata; please update microcode to version: 0xb2 (or later) Even if you had a hypervisor that does _not_ virtualize the TSC deadline and rather exposes the hardware one, it should be the hypervisors task to update microcode and possibly hide the flag from CPUID. So just hide the message when running on _any_ hypervisor, not just those that do not support the TSC deadline timer. The older check still makes sense, so keep it. Fixes: bd9240a18e ("x86/apic: Add TSC_DEADLINE quirk due to errata") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1507630377-54471-1-git-send-email-pbonzini@redhat.com
* Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds2017-09-121-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Ingo Molnar: "Two fixes: dead code removal, plus a SME memory encryption fix on 32-bit kernels that crashed Xen guests" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/cpu: Remove unused and undefined __generic_processor_info() declaration x86/mm: Make the SME mask a u64
| * x86/cpu: Remove unused and undefined __generic_processor_info() declarationDou Liyang2017-09-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following revert: 2b85b3d22920 ("x86/acpi: Restore the order of CPU IDs") ... got rid of __generic_processor_info(), but forgot to remove its declaration in mpspec.h. Remove the declaration and update the comments as well. Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: lenb@kernel.org Link: http://lkml.kernel.org/r/1505101403-29100-1-git-send-email-douly.fnst@cn.fujitsu.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
* | treewide: make "nr_cpu_ids" unsignedAlexey Dobriyan2017-09-081-1/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | First, number of CPUs can't be negative number. Second, different signnnedness leads to suboptimal code in the following cases: 1) kmalloc(nr_cpu_ids * sizeof(X)); "int" has to be sign extended to size_t. 2) while (loff_t *pos < nr_cpu_ids) MOVSXD is 1 byte longed than the same MOV. Other cases exist as well. Basically compiler is told that nr_cpu_ids can't be negative which can't be deduced if it is "int". Code savings on allyesconfig kernel: -3KB add/remove: 0/0 grow/shrink: 25/264 up/down: 261/-3631 (-3370) function old new delta coretemp_cpu_online 450 512 +62 rcu_init_one 1234 1272 +38 pci_device_probe 374 399 +25 ... pgdat_reclaimable_pages 628 556 -72 select_fallback_rq 446 369 -77 task_numa_find_cpu 1923 1807 -116 Link: http://lkml.kernel.org/r/20170819114959.GA30580@avx2 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* x86/apic: Silence "FW_BUG TSC_DEADLINE disabled due to Errata" on CPUs ↵Hans de Goede2017-08-311-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | without the feature When booting 4.13 on a VirtualBox VM on a Skylake host the following error shows up in the logs: [ 0.000000] [Firmware Bug]: TSC_DEADLINE disabled due to Errata; please update microcode to version: 0xb2 (or later) This is caused by apic_check_deadline_errata() only checking CPU model and not the X86_FEATURE_TSC_DEADLINE_TIMER flag (which VirtualBox does NOT export to the guest), combined with VirtualBox not exporting the micro-code version to the guest. This commit adds a check for X86_FEATURE_TSC_DEADLINE_TIMER to apic_check_deadline_errata(), silencing this error on VirtualBox VMs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Frank Mehnert <frank.mehnert@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Thayer <michael.thayer@oracle.com> Cc: Michal Necasek <michal.necasek@oracle.com> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: bd9240a18e ("x86/apic: Add TSC_DEADLINE quirk due to errata") Link: http://lkml.kernel.org/r/20170830105811.27539-1-hdegoede@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/apic: Remove the duplicated tracing versions of interruptsThomas Gleixner2017-08-291-33/+10
| | | | | | | | | | | | | | | | The error and the spurious interrupt are really rare events and not at all performance sensitive: two NOP5s can be tolerated when tracing is disabled. Remove the complication. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20170828064956.986009402@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/apic: Use this_cpu_ptr() in local_timer_interrupt()Thomas Gleixner2017-08-291-3/+3
| | | | | | | | | | | | | | Accessing the per cpu data via per_cpu(, smp_processor_id()) is pointless. Use this_cpu_ptr() instead. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20170828064956.829552757@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/apic: Remove the duplicated tracing version of local_timer_interrupt()Thomas Gleixner2017-08-291-19/+0
| | | | | | | | | | | | | | | | | The two NOP5s are noise in the rest of the work which is done by the timer interrupt and modern CPUs are pretty good in optimizing NOPs anyway. Get rid of the interrupt handler duplication and move the tracepoints into the regular handler. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20170828064956.751247330@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/irq: Get rid of the 'first_system_vector' indirection bogosityThomas Gleixner2017-08-292-3/+1
| | | | | | | | | | | | | | | | | | | This variable is beyond pointless. Nothing allocates a vector via alloc_gate() below FIRST_SYSTEM_VECTOR. So nothing can change first_system_vector. If there is a need for a gate below FIRST_SYSTEM_VECTOR then it can be added to the vector defines and FIRST_SYSTEM_VECTOR can be adjusted accordingly. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20170828064956.357109735@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/ioapic: Print the IRTE's index field correctly when enabling INTRraymond pang2017-08-231-1/+1
| | | | | | | | | | | | | | | | | | When enabling interrupt remap, IOAPIC's RTE contains the interrupt_index field of IRTE. This field is composed of the ->index and the ->index2 members of 'struct IR_IO_APIC_route_entry' - but what we print out currently only uses ->index. Fix it. Signed-off-by: Raymond Pang <raymondpangxd@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: joro@8bytes.org Cc: linux-arch@vger.kernel.org Link: http://lkml.kernel.org/r/CAHG4imNDzpDyOVi7MByVrLQ%3DQFuOVqpzJ5F-Xs5z6OZphubj-Q@mail.gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/ioapic: Pass the correct data to unmask_ioapic_irq()Seunghun Han2017-07-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | One of the rarely executed code pathes in check_timer() calls unmask_ioapic_irq() passing irq_get_chip_data(0) as argument. That's wrong as unmask_ioapic_irq() expects a pointer to the irq data of interrupt 0. irq_get_chip_data(0) returns NULL, so the following dereference in unmask_ioapic_irq() causes a kernel panic. The issue went unnoticed in the first place because irq_get_chip_data() returns a void pointer so the compiler cannot do a type check on the argument. The code path was added for machines with broken configuration, but it seems that those machines are either not running current kernels or simply do not longer exist. Hand in irq_get_irq_data(0) as argument which provides the correct data. [ tglx: Rewrote changelog ] Fixes: 4467715a44cc ("x86/irq: Move irq_cfg.irq_2_pin into io_apic.c") Signed-off-by: Seunghun Han <kkamagui@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1500369644-45767-1-git-send-email-kkamagui@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
* kernel/watchdog: split up config optionsNicholas Piggin2017-07-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR. LOCKUP_DETECTOR implies the general boot, sysctl, and programming interfaces for the lockup detectors. An architecture that wants to use a hard lockup detector must define HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH. Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and does not implement the LOCKUP_DETECTOR interfaces. sparc is unusual in that it has started to implement some of the interfaces, but not fully yet. It should probably be converted to a full HAVE_HARDLOCKUP_DETECTOR_ARCH. [npiggin@gmail.com: fix] Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Don Zickus <dzickus@redhat.com> Reviewed-by: Babu Moger <babu.moger@oracle.com> Tested-by: Babu Moger <babu.moger@oracle.com> [sparc] Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'x86-timers-for-linus' of ↵Linus Torvalds2017-07-031-0/+80
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 timers updates from Thomas Gleixner: "This update contains: - The solution for the TSC deadline timer borkage, which is caused by a hardware problem in the TSC_ADJUST/TSC_DEADLINE_TIMER logic. The problem is documented now and fixed with a microcode update, so we can remove the workaround and just check for the microcode version. If the microcode is not up to date, then the TSC deadline timer is disabled. If the borkage is fixed by the proper microcode version, then the deadline timer can be used. In both cases the restrictions to the range of the TSC_ADJUST value, which were added as workarounds, are removed. - A few simple fixes and updates to the timer related x86 code" * 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/tsc: Call check_system_tsc_reliable() before unsynchronized_tsc() x86/hpet: Do not use smp_processor_id() in preemptible code x86/time: Make setup_default_timer_irq() static x86/tsc: Remove the TSC_ADJUST clamp x86/apic: Add TSC_DEADLINE quirk due to errata x86/apic: Change the lapic name in deadline mode
| * x86/apic: Add TSC_DEADLINE quirk due to errataPeter Zijlstra2017-06-041-0/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Due to errata it is possible for the TSC_DEADLINE timer to misbehave after using TSC_ADJUST. A microcode update is available to fix this situation. Avoid using the TSC_DEADLINE timer if it is affected by this issue and report the required microcode version. [ tglx: Renamed function to apic_check_deadline_errata() ] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: kevin.b.stanton@intel.com Link: http://lkml.kernel.org/r/20170531155306.050849877@infradead.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
| * x86/apic: Change the lapic name in deadline modePeter Zijlstra2017-06-041-0/+1
| | | | | | | | | | | | | | | | | | | | So that we can more easily see in what mode the lapic timer operates. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: kevin.b.stanton@intel.com Link: http://lkml.kernel.org/r/20170531155305.989808008@infradead.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* | Merge branch 'irq-core-for-linus' of ↵Linus Torvalds2017-07-0313-90/+166
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq updates from Thomas Gleixner: "The irq department delivers: - Expand the generic infrastructure handling the irq migration on CPU hotplug and convert X86 over to it. (Thomas Gleixner) Aside of consolidating code this is a preparatory change for: - Finalizing the affinity management for multi-queue devices. The main change here is to shut down interrupts which are affine to a outgoing CPU and reenabling them when the CPU comes online again. That avoids moving interrupts pointlessly around and breaking and reestablishing affinities for no value. (Christoph Hellwig) Note: This contains also the BLOCK-MQ and NVME changes which depend on the rework of the irq core infrastructure. Jens acked them and agreed that they should go with the irq changes. - Consolidation of irq domain code (Marc Zyngier) - State tracking consolidation in the core code (Jeffy Chen) - Add debug infrastructure for hierarchical irq domains (Thomas Gleixner) - Infrastructure enhancement for managing generic interrupt chips via devmem (Bartosz Golaszewski) - Constification work all over the place (Tobias Klauser) - Two new interrupt controller drivers for MVEBU (Thomas Petazzoni) - The usual set of fixes, updates and enhancements all over the place" * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits) irqchip/or1k-pic: Fix interrupt acknowledgement irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity nvme: Allocate queues for all possible CPUs blk-mq: Create hctx for each present CPU blk-mq: Include all present CPUs in the default queue mapping genirq: Avoid unnecessary low level irq function calls genirq: Set irq masked state when initializing irq_desc genirq/timings: Add infrastructure for estimating the next interrupt arrival time genirq/timings: Add infrastructure to track the interrupt timings genirq/debugfs: Remove pointless NULL pointer check irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID irqchip/gic-v3-its: Add ACPI NUMA node mapping irqchip/gic-v3-its-platform-msi: Make of_device_ids const irqchip/gic-v3-its: Make of_device_ids const irqchip/irq-mvebu-icu: Add new driver for Marvell ICU irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU genirq/irqdomain: Remove auto-recursive hierarchy support irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access ...
| * | x86/apic: Mark single target interruptsThomas Gleixner2017-06-221-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the interrupt destination mode of the APIC is physical then the effective affinity is restricted to a single CPU. Mark the interrupt accordingly in the domain allocation code, so the core code can avoid pointless affinity setting attempts. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235447.508846202@linutronix.de
| * | x86/apic: Implement effective irq mask updateThomas Gleixner2017-06-222-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the effective irq mask update to the apic implementations and enable effective irq masks for x86. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.878370703@linutronix.de
| * | x86/apic: Add irq_data argument to apic->cpu_mask_to_apicid()Thomas Gleixner2017-06-224-15/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The decision to which CPUs an interrupt is effectively routed happens in the various apic->cpu_mask_to_apicid() implementations To support effective affinity masks this information needs to be updated in irq_data. Add a pointer to irq_data to the callbacks and feed it through the call chain. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.720739075@linutronix.de
| * | x86/apic: Move cpumask and to core codeThomas Gleixner2017-06-2210-32/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All implementations of apic->cpu_mask_to_apicid_and() and the two incoming cpumasks to search for the target. Move that operation to the call site and rename it to cpu_mask_to_apicid() Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.641575516@linutronix.de
| * | x86/apic: Move online masking to core codeThomas Gleixner2017-06-223-35/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All implementations of apic->cpu_mask_to_apicid_and() mask out the offline cpus. The callsite already has a mask available, which has the offline CPUs removed. Use that and remove the extra bits. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.560868224@linutronix.de
| * | x86/uv: Use default_cpu_mask_to_apicid_and()Thomas Gleixner2017-06-221-15/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Same functionality except the extra bits ored on the apicid. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.482841015@linutronix.de
| * | x86/apic: Move flat_cpu_mask_to_apicid_and() into C sourceThomas Gleixner2017-06-221-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | No point in having inlines assigned to function pointers at multiple places. Just bloats the text. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235446.405975721@linutronix.de
| * | x86/msi: Create named irq domainsThomas Gleixner2017-06-221-9/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the fwnode to create named irq domains so diagnosis works. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.299024560@linutronix.de
| * | x86/msi: Remove unused remap irq domain interfaceThomas Gleixner2017-06-221-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.221049665@linutronix.de
| * | x86/msi: Provide new iommu irqdomain interfaceThomas Gleixner2017-06-221-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide a new interface for creating the iommu remapping domains, so that the caller can supply a name and a id in order to create named irqdomains. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Joerg Roedel <joro@8bytes.org> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: iommu@lists.linux-foundation.org Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235443.986661206@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
| * | x86/htirq: Create named domainThomas Gleixner2017-06-221-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the fwnode to create a named domain so diagnosis works. Mark the init function __init while at it. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235443.829047007@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
| * | x86/ioapic: Create named irq domainThomas Gleixner2017-06-221-2/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the fwnode to create a named domain so diagnosis works, but only when the the ioapic is not device tree based. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235443.752782603@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
| * | x86/vector: Create named irq domainThomas Gleixner2017-06-221-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the fwnode to create a named domain so diagnosis works. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235443.673635238@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
generated by cgit v1.2.3 (git 2.25.1) at 2025-03-23 10:05:49 +0000