summaryrefslogtreecommitdiffstats
path: root/arch
Commit message (Collapse)AuthorAgeFilesLines
* x86: switch setup_sigcontext() to unsafe_put_user()Al Viro2020-03-182-46/+45
| | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: switch save_v86_state() to unsafe_put_user()Al Viro2020-03-181-31/+30
| | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: kill get_user_{try,catch,ex}Al Viro2020-03-181-54/+0
| | | | | | no users left Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: get rid of get_user_ex() in restore_sigcontext()Al Viro2020-03-181-50/+36
| | | | | | | | | Just do copyin into a local struct and be done with that - we are on a shallow stack here. [reworked by tglx, removing the macro horrors while we are touching that] Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: get rid of get_user_ex() in ia32_restore_sigcontext()Al Viro2020-03-181-62/+44
| | | | | | | | | Just do copyin into a local struct and be done with that - we are on a shallow stack here. [reworked by tglx, removing the macro horrors while we are touching that] Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* vm86: get rid of get_user_ex() useAl Viro2020-03-181-30/+24
| | | | | | | | | | | | | | | | | | Just do a copyin of what we want into a local variable and be done with that. We are guaranteed to be on shallow stack here... Note that conditional expression for range passed to access_ok() in mainline had been pointless all along - the only difference between vm86plus_struct and vm86_struct is that the former has one extra field in the end and when we get to copyin of that field (conditional upon 'plus' argument), we use copy_from_user(). Moreover, all fields starting with ->int_revectored are copied that way, so we only need that check (be it done by access_ok() or by user_access_begin()) only on the beginning of the structure - the fields that used to be covered by that get_user_try() block. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: get rid of small constant size cases in raw_copy_{to,from}_user()Al Viro2020-03-183-145/+2
| | | | | | | Very few call sites where that would be triggered remain, and none of those is anywhere near hot enough to bother. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86: switch sigframe sigset handling to explict __get_user()/__put_user()Al Viro2020-03-183-28/+14
| | | | | | | ... and consolidate the definition of sigframe_ia32->extramask - it's always a 1-element array of 32bit unsigned. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86 kvm page table walks: switch to explicit __get_user()Al Viro2020-02-151-1/+1
| | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* x86 user stack frame reads: switch to explicit __get_user()Al Viro2020-02-153-31/+11
| | | | | | rather than relying upon the magic in raw_copy_from_user() Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* Merge tag 'kbuild-v5.6-2' of ↵Linus Torvalds2020-02-0917-24/+24
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild updates from Masahiro Yamada: - fix randconfig to generate a sane .config - rename hostprogs-y / always to hostprogs / always-y, which are more natual syntax. - optimize scripts/kallsyms - fix yes2modconfig and mod2yesconfig - make multiple directory targets ('make foo/ bar/') work * tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: make multiple directory targets work kconfig: Invalidate all symbols after changing to y or m. kallsyms: fix type of kallsyms_token_table[] scripts/kallsyms: change table to store (strcut sym_entry *) scripts/kallsyms: rename local variables in read_symbol() kbuild: rename hostprogs-y/always to hostprogs/always-y kbuild: fix the document to use extra-y for vmlinux.lds kconfig: fix broken dependency in randconfig-generated .config
| * kbuild: rename hostprogs-y/always to hostprogs/always-yMasahiro Yamada2020-02-0417-24/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In old days, the "host-progs" syntax was used for specifying host programs. It was renamed to the current "hostprogs-y" in 2004. It is typically useful in scripts/Makefile because it allows Kbuild to selectively compile host programs based on the kernel configuration. This commit renames like follows: always -> always-y hostprogs-y -> hostprogs So, scripts/Makefile will look like this: always-$(CONFIG_BUILD_BIN2C) += ... always-$(CONFIG_KALLSYMS) += ... ... hostprogs := $(always-y) $(always-m) I think this makes more sense because a host program is always a host program, irrespective of the kernel configuration. We want to specify which ones to compile by CONFIG options, so always-y will be handier. The "always", "hostprogs-y", "hostprogs-m" will be kept for backward compatibility for a while. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
* | Merge tag 'x86-urgent-2020-02-09' of ↵Linus Torvalds2020-02-099-10/+230
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "A set of fixes for X86: - Ensure that the PIT is set up when the local APIC is disable or configured in legacy mode. This is caused by an ordering issue introduced in the recent changes which skip PIT initialization when the TSC and APIC frequencies are already known. - Handle malformed SRAT tables during early ACPI parsing which caused an infinite loop anda boot hang. - Fix a long standing race in the affinity setting code which affects PCI devices with non-maskable MSI interrupts. The problem is caused by the non-atomic writes of the MSI address (destination APIC id) and data (vector) fields which the device uses to construct the MSI message. The non-atomic writes are mandated by PCI. If both fields change and the device raises an interrupt after writing address and before writing data, then the MSI block constructs a inconsistent message which causes interrupts to be lost and subsequent malfunction of the device. The fix is to redirect the interrupt to the new vector on the current CPU first and then switch it over to the new target CPU. This allows to observe an eventually raised interrupt in the transitional stage (old CPU, new vector) to be observed in the APIC IRR and retriggered on the new target CPU and the new vector. The potential spurious interrupts caused by this are harmless and can in the worst case expose a buggy driver (all handlers have to be able to deal with spurious interrupts as they can and do happen for various reasons). - Add the missing suspend/resume mechanism for the HYPERV hypercall page which prevents resume hibernation on HYPERV guests. This change got lost before the merge window. - Mask the IOAPIC before disabling the local APIC to prevent potentially stale IOAPIC remote IRR bits which cause stale interrupt lines after resume" * tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/apic: Mask IOAPIC entries when disabling the local APIC x86/hyperv: Suspend/resume the hypercall page for hibernation x86/apic/msi: Plug non-maskable MSI affinity race x86/boot: Handle malformed SRAT tables during early ACPI parsing x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
| * | x86/apic: Mask IOAPIC entries when disabling the local APICTony W Wang-oc2020-02-071-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a system suspends, the local APIC is disabled in the suspend sequence, but the IOAPIC is left in the current state. This means unmasked interrupt lines stay unmasked. This is usually the case for IOAPIC pin 9 to which the ACPI interrupt is connected. That means that in suspended state the IOAPIC can respond to an external interrupt, e.g. the wakeup via keyboard/RTC/ACPI, but the interrupt message cannot be handled by the disabled local APIC. As a consequence the Remote IRR bit is set, but the local APIC does not send an EOI to acknowledge it. This causes the affected interrupt line to become stale and the stale Remote IRR bit will cause a hang when __synchronize_hardirq() is invoked for that interrupt line. To prevent this, mask all IOAPIC entries before disabling the local APIC. The resume code already has the unmask operation inside. [ tglx: Massaged changelog ] Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/1579076539-7267-1-git-send-email-TonyWWang-oc@zhaoxin.com
| * | x86/hyperv: Suspend/resume the hypercall page for hibernationDexuan Cui2020-02-011-0/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For hibernation the hypercall page must be disabled before the hibernation image is created so that subsequent hypercall operations fail safely. On resume the hypercall page has to be restored and reenabled to ensure proper operation of the resumed kernel. Implement the necessary suspend/resume callbacks. [ tglx: Decrypted changelog ] Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/1578350559-130275-1-git-send-email-decui@microsoft.com
| * | x86/apic/msi: Plug non-maskable MSI affinity raceThomas Gleixner2020-02-012-3/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Evan tracked down a subtle race between the update of the MSI message and the device raising an interrupt internally on PCI devices which do not support MSI masking. The update of the MSI message is non-atomic and consists of either 2 or 3 sequential 32bit wide writes to the PCI config space. - Write address low 32bits - Write address high 32bits (If supported by device) - Write data When an interrupt is migrated then both address and data might change, so the kernel attempts to mask the MSI interrupt first. But for MSI masking is optional, so there exist devices which do not provide it. That means that if the device raises an interrupt internally between the writes then a MSI message is sent built from half updated state. On x86 this can lead to spurious interrupts on the wrong interrupt vector when the affinity setting changes both address and data. As a consequence the device interrupt can be lost causing the device to become stuck or malfunctioning. Evan tried to handle that by disabling MSI accross an MSI message update. That's not feasible because disabling MSI has issues on its own: If MSI is disabled the PCI device is routing an interrupt to the legacy INTx mechanism. The INTx delivery can be disabled, but the disablement is not working on all devices. Some devices lose interrupts when both MSI and INTx delivery are disabled. Another way to solve this would be to enforce the allocation of the same vector on all CPUs in the system for this kind of screwed devices. That could be done, but it would bring back the vector space exhaustion problems which got solved a few years ago. Fortunately the high address (if supported by the device) is only relevant when X2APIC is enabled which implies interrupt remapping. In the interrupt remapping case the affinity setting is happening at the interrupt remapping unit and the PCI MSI message is programmed only once when the PCI device is initialized. That makes it possible to solve it with a two step update: 1) Target the MSI msg to the new vector on the current target CPU 2) Target the MSI msg to the new vector on the new target CPU In both cases writing the MSI message is only changing a single 32bit word which prevents the issue of inconsistency. After writing the final destination it is necessary to check whether the device issued an interrupt while the intermediate state #1 (new vector, current CPU) was in effect. This is possible because the affinity change is always happening on the current target CPU. The code runs with interrupts disabled, so the interrupt can be detected by checking the IRR of the local APIC. If the vector is pending in the IRR then the interrupt is retriggered on the new target CPU by sending an IPI for the associated vector on the target CPU. This can cause spurious interrupts on both the local and the new target CPU. 1) If the new vector is not in use on the local CPU and the device affected by the affinity change raised an interrupt during the transitional state (step #1 above) then interrupt entry code will ignore that spurious interrupt. The vector is marked so that the 'No irq handler for vector' warning is supressed once. 2) If the new vector is in use already on the local CPU then the IRR check might see an pending interrupt from the device which is using this vector. The IPI to the new target CPU will then invoke the handler of the device, which got the affinity change, even if that device did not issue an interrupt 3) If the new vector is in use already on the local CPU and the device affected by the affinity change raised an interrupt during the transitional state (step #1 above) then the handler of the device which uses that vector on the local CPU will be invoked. expose issues in device driver interrupt handlers which are not prepared to handle a spurious interrupt correctly. This not a regression, it's just exposing something which was already broken as spurious interrupts can happen for a lot of reasons and all driver handlers need to be able to deal with them. Reported-by: Evan Green <evgreen@chromium.org> Debugged-by: Evan Green <evgreen@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Evan Green <evgreen@chromium.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
| * | x86/boot: Handle malformed SRAT tables during early ACPI parsingSteven Clarkson2020-01-311-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Break an infinite loop when early parsing of the SRAT table is caused by a subtable with zero length. Known to affect the ASUS WS X299 SAGE motherboard with firmware version 1201 which has a large block of zeros in its SRAT table. The kernel could boot successfully on this board/firmware prior to the introduction of early parsing this table or after a BIOS update. [ bp: Fixup whitespace damage and commit message. Make it return 0 to denote that there are no immovable regions because who knows what else is broken in this BIOS. ] Fixes: 02a3e3cdb7f1 ("x86/boot: Parse SRAT table and count immovable memory regions") Signed-off-by: Steven Clarkson <sc@lambdal.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: linux-acpi@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=206343 Link: https://lkml.kernel.org/r/CAHKq8taGzj0u1E_i=poHUam60Bko5BpiJ9jn0fAupFUYexvdUQ@mail.gmail.com
| * | x86/timer: Don't skip PIT setup when APIC is disabled or in legacy modeThomas Gleixner2020-01-296-7/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tony reported a boot regression caused by the recent workaround for systems which have a disabled (clock gate off) PIT. On his machine the kernel fails to initialize the PIT because apic_needs_pit() does not take into account whether the local APIC interrupt delivery mode will actually allow to setup and use the local APIC timer. This should be easy to reproduce with acpi=off on the command line which also disables HPET. Due to the way the PIT/HPET and APIC setup ordering works (APIC setup can require working PIT/HPET) the information is not available at the point where apic_needs_pit() makes this decision. To address this, split out the interrupt mode selection from apic_intr_mode_init(), invoke the selection before making the decision whether PIT is required or not, and add the missing checks into apic_needs_pit(). Fixes: c8c4076723da ("x86/timer: Skip PIT initialization on modern chipsets") Reported-by: Anthony Buckley <tony.buckley000@gmail.com> Tested-by: Anthony Buckley <tony.buckley000@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Daniel Drake <drake@endlessm.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=206125 Link: https://lore.kernel.org/r/87sgk6tmk2.fsf@nanos.tec.linutronix.de
* | | Merge tag 'irq-urgent-2020-02-09' of ↵Linus Torvalds2020-02-092-10/+10
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull interrupt fixes from Thomas Gleixner: "A set of fixes for the interrupt subsystem: - Provision only ACPI enabled redistributors on GICv3 - Use the proper command colums when building the INVALL command for the GICv3-ITS - Ensure the allocation of the L2 vPE table for GICv4.1 - Correct the GICv4.1 VPROBASER programming so it uses the proper size - A set of small GICv4.1 tidy up patches - Configuration cleanup for C-SKY interrupt chip - Clarify the function documentation for irq_set_wake() to document that the wakeup functionality is orthogonal to the irq disable/enable mechanism" * tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors irqchip/gic-v3-its: Remove superfluous WARN_ON irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd() irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level irqchip/gic-v4.1: Set vpe_l1_base for all redistributors irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE genirq: Clarify that irq wake state is orthogonal to enable/disable irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL irqchip: Some Kconfig cleanup for C-SKY irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
| * \ \ Merge tag 'irqchip-fixes-5.6-1' of ↵Thomas Gleixner2020-02-082-10/+10
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent Pull irqchip fixes for 5.6, take #1 from Marc Zyngier: - Guarantee allocation of L2 vPE table for GICv4.1 - Fix GICv4.1 VPROPBASER programming - Numerous GICv4.1 tidy ups - Fix disabled GICv3 redistributor provisioning with ACPI - KConfig cleanup for C-SKY
| | * | | irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessorsZenghui Yu2020-02-082-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | V{PEND,PROP}BASER registers are actually located in VLPI_base frame of the *redistributor*. Rename their accessors to reflect this fact. No functional changes. Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200206075711.1275-7-yuzenghui@huawei.com
* | | | | Merge tag 'efi-urgent-2020-02-09' of ↵Linus Torvalds2020-02-091-1/+1
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull EFI fix from Thomas Gleixner: "A single fix for a EFI boot regression on X86 which was caused by the recent rework of the EFI memory map parsing. On systems with invalid memmap entries the cleanup function uses an value which cannot be relied on in this stage. Use the actual EFI memmap entry instead" * tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi/x86: Fix boot regression on systems with invalid memmap entries
| * | | | | efi/x86: Fix boot regression on systems with invalid memmap entriesArd Biesheuvel2020-02-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In efi_clean_memmap(), we do a pass over the EFI memory map to remove bogus entries that may be returned on certain systems. This recent commit: 1db91035d01aa8bf ("efi: Add tracking for dynamically allocated memmaps") refactored this code to pass the input to efi_memmap_install() via a temporary struct on the stack, which is populated using an initializer which inadvertently defines the value of its size field in terms of its desc_size field, which value cannot be relied upon yet in the initializer itself. Fix this by using efi.memmap.desc_size instead, which is where we get the value for desc_size from in the first place. Reported-by: Jörg Otte <jrg.otte@gmail.com> Tested-by: Jörg Otte <jrg.otte@gmail.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: linux-efi@vger.kernel.org Cc: jrg.otte@gmail.com Cc: torvalds@linux-foundation.org Cc: mingo@kernel.org Link: https://lore.kernel.org/r/20200201233304.18322-1-ardb@kernel.org
* | | | | | Merge tag 'powerpc-5.6-2' of ↵Linus Torvalds2020-02-082-5/+7
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Fix an existing bug in our user access handling, exposed by one of the bug fixes we merged this cycle. - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the recently added CONFIG_VMAP_STACK. Thanks to: Christophe Leroy, Guenter Roeck. * tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK powerpc/futex: Fix incorrect user access blocking
| * | | | | | powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACKChristophe Leroy2020-02-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When CONFIG_PROVE_LOCKING is selected together with (now default) CONFIG_VMAP_STACK, kernel enter deadlock during boot. At the point of checking whether interrupts are enabled or not, the value of MSR saved on stack is read using the physical address of the stack. But at this point, when using VMAP stack the DATA MMU translation has already been re-enabled, leading to deadlock. Don't use the physical address of the stack when CONFIG_VMAP_STACK is set. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reported-by: Guenter Roeck <linux@roeck-us.net> Fixes: 028474876f47 ("powerpc/32: prepare for CONFIG_VMAP_STACK") Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/daeacdc0dec0416d1c587cc9f9e7191ad3068dc0.1581095957.git.christophe.leroy@c-s.fr
| * | | | | | powerpc/futex: Fix incorrect user access blockingMichael Ellerman2020-02-081-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The early versions of our kernel user access prevention (KUAP) were written by Russell and Christophe, and didn't have separate read/write access. At some point I picked up the series and added the read/write access, but I failed to update the usages in futex.h to correctly allow read and write. However we didn't notice because of another bug which was causing the low-level code to always enable read and write. That bug was fixed recently in commit 1d8f739b07bd ("powerpc/kuap: Fix set direction in allow/prevent_user_access()"). futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and does: 1: lwarx %1, 0, %3 cmpw 0, %1, %4 bne- 3f 2: stwcx. %5, 0, %3 Which clearly loads and stores from/to %3. The logic in arch_futex_atomic_op_inuser() is similar, so fix both of them to use allow_read_write_user(). Without this fix, and with PPC_KUAP_DEBUG=y, we see eg: Bug: Read fault blocked by AMR! WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30 CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G W 5.5.0-rc7-gcc9x-g4c25df5640ae #1 ... NIP [c000000000070680] __do_page_fault+0x600/0xf30 LR [c00000000007067c] __do_page_fault+0x5fc/0xf30 Call Trace: [c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable) [c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30 --- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0 LR = futex_lock_pi_atomic+0xe0/0x1f0 [c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable) [c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60 [c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0 [c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200 [c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68 Fixes: de78a9c42a79 ("powerpc: Add a framework for Kernel Userspace Access Protection") Cc: stable@vger.kernel.org # v5.2+ Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr> Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au
* | | | | | | Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds2020-02-0830-671/+645
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM SoC late updates from Olof Johansson: "This is some material that we picked up into our tree late, or that had more complex dependencies on more than one topic branch that makes sense to keep separately. - TI support for secure accelerators and hwrng on OMAP4/5 - TI camera changes for dra7 and am437x and SGX improvement due to better reset control support on am335x, am437x and dra7 - Davinci moves to proper clocksource on DM365, and regulator/audio improvements for DM365 and DM644x eval boards" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits) ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt ARM: dts: Configure interconnect target module for am437x sgx ARM: dts: Configure sgx for dra7 ARM: dts: Configure rstctrl reset for am335x SGX ARM: dts: dra7: Add ti-sysc node for VPE ARM: dts: dra7: add vpe clkctrl node ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries ARM: dts: am43xx: add support for clkout1 clock arm: dts: dra76-evm: Add CAL and OV5640 nodes arm: dtsi: dra76x: Add CAL dtsi node arm: dts: dra72-evm-common: Add entries for the CSI2 cameras ARM: dts: DRA72: Add CAL dtsi node ARM: dts: dra7-l4: Add ti-sysc node for CAM ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only ARM: dts: dra7: add cam clkctrl node ARM: OMAP2+: Drop legacy platform data for omap4 des ARM: OMAP2+: Drop legacy platform data for omap4 sham ARM: OMAP2+: Drop legacy platform data for omap4 aes ...
| * \ \ \ \ \ \ Merge tag 'davinci-for-v5.6/soc' of ↵Olof Johansson2020-01-279-479/+56
| |\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late DaVinci SoC updates for v5.6 include migrating DM365 SoC to use drivers/clocksource based driver for timer. This leads to removal of machine specific timer driver. There are two patches adding missing fixed regulators for audio codecs on DM365 and DM644x EVMs. * tag 'davinci-for-v5.6/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: ARM: davinci: dm644x-evm: Add Fixed regulators needed for tlv320aic33 ARM: davinci: dm365-evm: Add Fixed regulators needed for tlv320aic3101 ARM: davinci: remove legacy timer support ARM: davinci: dm365: switch to using the clocksource driver clocksource: davinci: only enable clockevents once tim34 is initialized Link: https://lore.kernel.org/r/043eb5b2-a302-4de6-a3e8-8238e49483b1@ti.com/ Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | | | | | | ARM: davinci: dm644x-evm: Add Fixed regulators needed for tlv320aic33Peter Ujfalusi2020-01-131-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The codec driver needs correct regulators in order to probe. Both VCC_3.3V and VCC_1.8V is always on fixed regulators on the board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
| | * | | | | | | ARM: davinci: dm365-evm: Add Fixed regulators needed for tlv320aic3101Peter Ujfalusi2020-01-131-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The codec driver needs correct regulators in order to probe. Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
| | * | | | | | | ARM: davinci: remove legacy timer supportBartosz Golaszewski2020-01-136-472/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All platforms have now been switched to the new clocksource driver. Remove the old code and various no longer needed bits and pieces. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
| | * | | | | | | ARM: davinci: dm365: switch to using the clocksource driverBartosz Golaszewski2020-01-131-7/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We now have a proper clocksource driver for davinci. Switch the dm365 platform to using it. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
| * | | | | | | | Merge tag 'omap-for-v5.6/dt-late-signed' of ↵Olof Johansson2020-01-2525-70/+1085
| |\ \ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late Late omap dts changes for v5.6 merge window This series of changes mostly configures the cameras for dra7 and am437x that have been pending for few months now because of waiting for clock dependencies to clear. So these changes are based on earlier dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in. Then there's a series of changes to configure powervr sgx target module for am335x, am437x and dra7 that have been waiting to have the rstctrl reset driver dependencies to clear. Also included are few minor patches to configure 1-wire and coulomb counter calibration interrupt for droid4. * tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits) ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt ARM: dts: Configure interconnect target module for am437x sgx ARM: dts: Configure sgx for dra7 ARM: dts: Configure rstctrl reset for am335x SGX ARM: dts: dra7: Add ti-sysc node for VPE ARM: dts: dra7: add vpe clkctrl node ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries ARM: dts: am43xx: add support for clkout1 clock arm: dts: dra76-evm: Add CAL and OV5640 nodes arm: dtsi: dra76x: Add CAL dtsi node arm: dts: dra72-evm-common: Add entries for the CSI2 cameras ARM: dts: DRA72: Add CAL dtsi node ARM: dts: dra7-l4: Add ti-sysc node for CAM ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only ARM: dts: dra7: add cam clkctrl node ARM: dts: Add omap3-echo ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725 ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0 ... Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3 Signed-off-by: Olof Johansson <olof@lixom.net>
| | * | | | | | | | ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmemTony Lindgren2020-01-231-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With "[PATCHv3] w1: omap-hdq: Simplify driver with PM runtime autosuspend" we can read the droid4 battery information over 1-wire with this patch with something like: # modprobe omap_hdq # hd /sys/bus/w1/devices/89-*/89-*/nvmem ... Unfortunately the format of the battery data seems to be Motorola specific and is currently unusable for battery charger unless somebody figures out what it means. Note that currently keeping omap_hdq module loaded will cause extra power consumption as it seems to scan devices periodically. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | | | | | | | ARM: dts: motorola-cpcap-mapphone: Configure calibration interruptTony Lindgren2020-01-231-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We added coulomb counter calibration support With commit 0cb90f071f73 ("power: supply: cpcap-battery: Add basic coulomb counter calibrate support"), but we also need to configure the related interrupt. Without the interrupt calibration happens based on a timeout after two seconds, with the interrupt the calibration just gets done a bit faster. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | | | | | | | ARM: dts: Configure interconnect target module for am437x sgxTony Lindgren2020-01-231-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This seems to be similar to what we have for am335x. The following can be tested via sysfs with the to ensure the SGX module gets enabled and disabled properly: # echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5600fe00 # revision register 0x5600fe00 = 0x40000000 # echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5000fe00 Bus error Note that this patch depends on the PRM rstctrl driver that has been recently posted. If the child device driver(s) need to prevent rstctrl reset on PM runtime suspend, the drivers need to increase the usecount for the shared rstctrl reset that can be mapped also for the child device(s) or accessed via dev->parent. Cc: Adam Ford <aford173@gmail.com> Cc: Filip Matijević <filip.matijevic.pz@gmail.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: moaz korena <moaz@korena.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: Philipp Rossak <embed3d@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | | | | | | | ARM: dts: Configure sgx for dra7Tony Lindgren2020-01-231-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I've tested that the interconnect target module enables and idles just fine when probed with ti-sysc with PM runtime control via sys: # echo on > $(find /sys -name control | grep \/5600) # rwmem 0x5600fe00 # OCP Revision 0x5600fe00 = 0x40000000 # echo auto > $(find /sys -name control | grep \/5600) Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | | | | | | | ARM: dts: Configure rstctrl reset for am335x SGXTony Lindgren2020-01-231-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following can be tested via sysfs with the following to ensure the SGX module gets enabled and disabled properly: # echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5600fe00 # revision register 0x5600fe00 = 0x40000000 # echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5000fe00 Bus error Note that this patch depends on the PRM rstctrl driver that has been recently posted. If the child device driver(s) need to prevent rstctrl reset on PM runtime suspend, the drivers need to increase the usecount for the shared rstctrl reset that can be mapped also for the child device(s) or accessed via dev->parent. Cc: Adam Ford <aford173@gmail.com> Cc: Filip Matijević <filip.matijevic.pz@gmail.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: moaz korena <moaz@korena.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: Philipp Rossak <embed3d@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * | | | | | | | Merge branch 'omap-for-v5.6/ti-sysc-dt-cam' into omap-for-v5.6/dtTony Lindgren2020-01-2311-16/+361
| | |\ \ \ \ \ \ \ \
| | | * | | | | | | | ARM: dts: dra7: Add ti-sysc node for VPEBenoit Parrot2020-01-231-3/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add VPE node as a child of l4 interconnect in order for it to probe using ti-sysc. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: dra7: add vpe clkctrl nodeBenoit Parrot2020-01-231-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add clkctrl nodes for VPE module. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "vpe-clkctrl@" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entriesBenoit Parrot2020-01-231-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add VPFE device nodes entries. Add OmniVision OV2659 sensor device nodes and linkage. Since Rev1.2a on this board the sensor source clock (xvclk) has a dedicated 12Mhz oscillator instead of using clkout1. Add 'audio_mstrclk' fixed clock object to represent it. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entriesBenoit Parrot2020-01-231-1/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add VPFE device nodes entries. Add OmniVision OV2659 sensor device nodes and linkage. The sensor clock (xvclk) is sourced from clkout1. Add clock entries to properly select clkout1 and set its parent clock to sys_clkin_ck. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: am43xx: add support for clkout1 clockTero Kristo2020-01-231-0/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | clkout1 clock node and its generation tree was missing. Add this based on the data on TRM and PRCM functional spec. commit 664ae1ab2536 ("ARM: dts: am43xx: add clkctrl nodes") effectively reverted this commit 8010f13a40d3 ("ARM: dts: am43xx: add support for clkout1 clock") which is needed for the ov2659 camera sensor clock definition hence it is being re-applied here. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "clkout1-*ck" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. Fixes: 664ae1ab2536 ("ARM: dts: am43xx: add clkctrl nodes") Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | arm: dts: dra76-evm: Add CAL and OV5640 nodesBenoit Parrot2020-01-231-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add device nodes for CSI2 camera board OV5640. Add the CAL port nodes with the necessary linkage to the ov5640 nodes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | arm: dtsi: dra76x: Add CAL dtsi nodeBenoit Parrot2020-01-231-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA76 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | arm: dts: dra72-evm-common: Add entries for the CSI2 camerasBenoit Parrot2020-01-231-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add device nodes for CSI2 camera board OV5640. Add the CAL port nodes with the necessary linkage to the ov5640 nodes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: DRA72: Add CAL dtsi nodeBenoit Parrot2020-01-231-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA72 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: dts: dra7-l4: Add ti-sysc node for CAMBenoit Parrot2020-01-231-6/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add CAM nodes as a child of l4 interconnect in order for it to probe using ti-sysc. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | | | | | | ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP onlyBenoit Parrot2020-01-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Both CAL and VIP rely on this clock domain. But CAL DPHY require LVDSRX_96M_GFCLK to be active. When this domain is set to HWSUP the LVDSRX_96M_GFCLK is on;y active when VIP1 clock is also active. If only CAL on DRA72x (which uses the VIP2 clkctrl) probes the CAM domain is enabled but the LVDSRX_96M_GFCLK is left gated. Since LVDSRX_96M_GFCLK is sourcing the input clock to the DPHY then actual frame capture cannot start as the phy are inactive. So we either have to also enabled VIP1 even if we don't intend on using it or we need to set the CAM domain to use SWSUP only. This patch implements the latter. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 01:15:23 +0000