| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Building the newly added uniphier system bus driver as a module
causes a link error, so let's only allow it to be built-in for
now, to fix allmodconfig:
ERROR: "of_default_bus_match_table" [drivers/bus/uniphier-system-bus.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The UniPhier System Bus is an external bus that connects on-board
devices to the UniPhier SoC. Each bank (chip select) is dynamically
mapped to the CPU-viewed address base via the bus controller. The
bus controller must be configured before any access to the bus.
This driver parses the "ranges" property of the System Bus node and
initialized the bus controller. After the bus becomes ready, devices
below it are populated.
Note:
Each bank can be mapped anywhere in the supported address space;
there is nothing preventing us from assigning bank 0 on 0x42000000,
0x43000000, or anywhere as long as such region is not used by others.
So, the "ranges" is just one possible software configuration, which
does not seem to fit in device tree because device tree is a hardware
description language. However, of_translate_address() requires
"ranges" in every bus node between CPUs and device mapped on the CPU
address space. In other words, "ranges" properties must be statically
defined in device tree. After some discussion, I decided the dynamic
address reassignment by the driver is too bothersome. Instead, the
device tree should provide a reasonable translation setup that the OS
can rely on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
0x4e is the runtime address normally associated with perihperal ICs.
0x45 is not a valid runtime address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |
| |
| |
| |
| |
| |
| | |
The primary PMICs use 0x3a3 as their hardware address, not 0x3e3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Don't forget to unlock before returning an error code.
Fixes: d787dcdb9c8f ('bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
| |\| |
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Reduced Serial Bus (RSB) is an Allwinner proprietery interface
used to communicate with PMICs and other peripheral ICs.
RSB is a two-wire push-pull serial bus that supports 1 master
device and up to 15 active slave devices.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When PMU context is migrating between CPUs, interrupt affinity is set as
well. Only this should not happen when the CCN interrupt is not being
used at all (the driver is using a hrtimer tick instead).
Fixed now.
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When migrating events the driver picks another cpu using
cpumask_any_but() function, which returns value >= nr_cpu_ids
when there is none available, not a negative value as the code
assumed. Fixed now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| |/ /
| |
| |
| |
| |
| |
| | |
Remove extra space between platform prefix and driver name in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |/
|
|
|
|
|
|
|
|
|
| |
Disable building CCI-500 PMU driver by default.
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: arm@kernel.org
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
regmap_init(...) is a macro since commit
"regmap: Use different lockdep class for each regmap init call".
That same name is used as a function pointer: prevent its expansion
by adding parentheses around the function pointer.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711ed7 ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
mips_cdmm_phys_base() is defined only in arch/mips/mti-malta/malta-memory.c
so there's no problem with multiple definitions. But it works better to
have a weak default implementation and allow a strong function to override
it. Then we don't have to test whether a definition is present, and if
there are ever multiple strong definitions, we get a link error instead of
calling a random definition.
Add a weak mips_cdmm_phys_base() definition and remove the weak annotation
from the declaration in arch/mips/include/asm/cdmm.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10688/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
next/drivers
Merge "mvebu drivers change for 4.2" from Gregory CLEMENT:
mvebu-mbus: add mv_mbus_dram_info_nooverlap() needed for the new
Marvell crypto driver
* tag 'mvebu-drivers-4.2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: add mv_mbus_dram_info_nooverlap()
Based on the earlier bug fixes branch, which contains six other
patches already merged into 4.1.
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Each CCI model have different event/source codes and formats. This
patch exports this information via the sysfs, which includes the
aliases for the events. The aliases are listed by 'perf list', helping
the users to specify the name of the event instead of the binary
config values.
Each event alias must accompany the 'source' code except for the
following cases :
1) CCI-400 - cycles event, doesn't relate to an interface.
2) CCI-500 - Global events to the CCI. (Fixed source code = 0xf)
Each CCI model provides two sets of attributes(format and event),
which are dynamically populated before registering the PMU, to
allow for the appropriate information.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
CCI-500 provides 8 event counters which can count any of the
supported events independently. The PMU event id is a 9-bit
value made of two parts.
bits [8:5] - Source port
0x0-0x6 Slave Ports
0x8-0xD Master Ports
0xf Global Events to CCI
0x7,0xe Reserved
bits [0:4] - Event code (specific to each type of port)
The generic CCI-500 controlling interface remains the same with CCI-400.
However there are some differences in the PMU event counters.
- No cycle counter
- Upto 8 counters(4 in CCI-400)
- Each counter area is 64K(4K in CCI400)
- The counter0 starts at offset 0x10000 from the base of CCI
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Rename CCI400 specific defintions from CCI_xxx to CCI400_xxx.
Introduce generic ARM_CCI_PMU to cover common code for handling
the CCI PMU.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Given that each CCI has different set of interfaces and
its associated events, it is good to abstract the validation of the
event codes to make it easier to add support for a new CCI model.
This patch also abstracts the mapping of a given event to a counter,
as there are some special counters for certain specific events.
We assume that the fixed hardware counters are always at the beginning,
so that we can use cci_model->fixed_hw_events as an upper bound to given
idx to check if we need to program the counter for an event.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adds the PMU model specific counters to the PMU model
abstraction to make it easier to add a new PMU.
The patch cleans up the naming convention used all over
the code.
e.g, CCI_PMU_MAX_HW_EVENTS => maximum number of events that
can be counted at any time, which is in fact the maximum
number of counters available.
Change all such namings to use 'counters' instead of events.
This patch also abstracts the following:
1) Size of a PMU event counter area.
2) Maximum number of programmable counters supported by the PMU model
3) Number of counters which counts fixed events (e.g, cycle
counter on CCI-400).
Also changes some of the static allocation of the data
structures to dynamic, to accommodate the number of events
supported by a PMU.
Gets rid ofthe CCI_PMU_* defines for the model. All such
data should be accessed via the model abstraction.
Limits the number of counters to the maximum supported
by the 'model'.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch gets rid of the global struct cci_pmu variable and makes
the code use the cci_pmu explicitly. Makes code a bit more robust
and reader friendly.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Do not enable CCI-400 PMU by default and fix the dependency on PERF_EVENTS
than HW_PERF_EVENTS.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: arm@kernel.org
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
hrtimer_start() will no longer defer already expired timers to the
softirq in 4.2, and the __hrtimer_start_range_ns() function is
getting removed, causing build errors when both the tip tree and
the arm-ccn changes are merged.
This changes the code back to using hrtimer_start, which will
do the right thing after this branch gets merged with the
timers update from tip.
As pointed out after a discussion on the mailing list, the result will
not be worse than the what was there before you pulled my updates, as
the code was using normal hrtimer_start(). It's just when I realised
that it should be pinned I looked at what x86 uncore pmu is doing and
shamelessly (and probably a bit mindlessly) copied the "do not wakeup"
version from there.
[arnd: update commit message]
Reported-by: Mark Brown <mark.brown@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.linaro.org/people/pawel.moll/linux into next/drivers
Pull "Set of ARM CCN PMU driver updates" from Pawel Moll:
- fixed a nasty bitfield mangling bug
- added new hints to the perf userspace tool
- pinned events processing to a single PMU
- modified events initialisation so they can be rotated now
* tag 'ccn/updates-for-4.2' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: Allocate event when it is being added, not initialised
bus: arm-ccn: Do not group CCN events with other PMUs
bus: arm-ccn: Provide required event arguments
bus: arm-ccn: cpumask attribute
bus: arm-ccn: Fix node->XP config conversion
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
To make events rotation possible, they should be allocated when event
is being ->added(), not during initialisation. This patch moves the
respective code.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Groups must not mix events from different PMUs (software events are
allowed). Unfortunately the core does not ensures that, so it is
necessary to validate the group at the PMU driver level.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since 688d4dfcdd624192cbf03c08402e444d1d11f294 "perf tools: Support
parsing parameterized events" the perf userspace tools understands
"argument=?" syntax in the events file, making sure that required
arguments are provided by the user and not defaulting to 0, causing
confusion.
This patch adds the required arguments lists for CCN events.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds a "cpumask" attribute to CCN's event_source class sysfs
directory. Perf user tool uses it to restrict events to the
processor(s) enumerated in this mask.
This patch provides a single CPU mask, making it possible to run "-a"
perf session (previously it would request the same CCN event, for
example cycle counter, on each available core and most likely fail).
Initially the mask is set to the CPU that happened to probe the driver,
but it will be changed when it is hot-un-plugged (active events are
migrated to another CPU then).
Example:
Performance counter stats for 'system wide':
CPU0 2968148 cycles
CPU1 2236736 cycles
CPU2 1797968 cycles
CPU3 1831715 cycles
CPU1 1201850868 ccn/cycles/
1.001241383 seconds time elapsed
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Events defined as watchpoints on nodes must have their config values
converted so that they apply to the respective node's XP. The
function setting new values was using wrong mask for the "port" field,
resulting in corrupted value. Fixed now.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
|
| | |\ \ \ \
| | |/ / /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
into next/soc
Merge "changes for Broadcom SoCs":
- Dan fixes an error path in the BCM63xx SMP code
- Ray adds the relevant Kconfig selects to enable the Broadcom NAND driver on Cygnus
- Kevin provides a change to the Broadcom GISB arbiter driver to make it work with
MIPS-based big-endian STB SoCs (this was a long-standing change that had dependencies on
code in drivers/of/*)
- Gregory enables the use of GPIOLIB for brcmstb SoCs and bumps the number of GPIOs for
these platforms
* tag 'arm-soc/for-4.2/soc-part2' of http://github.com/broadcom/stblinux:
ARM: brcmstb: Add default gpio number
ARM: brcmstb: Select ARCH_WANT_OPTIONAL_GPIOLIB
bus: brcmstb_gisb: Honor the "big-endian" and "native-endian" DT properties
ARM: BCM: Enable NAND support for iProc SoCs
ARM: BCM63xx: fix an error path in bcm63xx_pmb_power_on_cpu()
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On chips strapped for BE, we'll need to use ioread32be/iowrite32be instead of
ioread32/iowrite32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
|
| | | \ \ \ | |
| | | \ \ \ | |
| | |\ \| | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
* pm-sleep:
PM / sleep: trace_device_pm_callback coverage in dpm_prepare/complete
PM / wakeup: add a dummy wakeup_source to record statistics
PM / sleep: Make suspend-to-idle-specific code depend on CONFIG_SUSPEND
PM / sleep: Return -EBUSY from suspend_enter() on wakeup detection
PM / tick: Add tracepoints for suspend-to-idle diagnostics
PM / sleep: Fix symbol name in a comment in kernel/power/main.c
leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger
ARM: omap-device: use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
bus: omap_l3_noc: add missed callbacks for suspend-to-disk
PM / sleep: Add macro to define common noirq system PM callbacks
PM / sleep: Refine diagnostic messages in enter_state()
PM / wakeup: validate wakeup source before activating it.
* pm-runtime:
PM / Runtime: Update last_busy in rpm_resume
PM / runtime: add note about re-calling in during device probe()
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add missed callbacks needed for proper supporting of suspend-to-disk
by using recently introduced macro SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \ \ \ \
| |/ / / /
|/| | | /
| | |_|/
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This commit introduces a variant of the mv_mbus_dram_info() function
called mv_mbus_dram_info_nooverlap(). Both functions are used by
Marvell drivers supporting devices doing DMA, and provide them a
description the DRAM ranges that they need to configure their DRAM
windows.
The ranges provided by the mv_mbus_dram_info() function may overlap
with the I/O windows if there is a lot (>= 4 GB) of RAM
installed. This is not a problem for most of the DMA masters, except
for the upcoming new CESA crypto driver because it does DMA to the
SRAM, which is mapped through an I/O window. For this unit, we need to
have DRAM ranges that do not overlap with the I/O windows.
A first implementation done in commit 1737cac69369 ("bus: mvebu-mbus:
make sure SDRAM CS for DMA don't overlap the MBus bridge window"),
changed the information returned by mv_mbus_dram_info() to match this
requirement. However, it broke the requirement of the other DMA
masters than the DRAM ranges should have power of two sizes.
To solve this situation, this commit introduces a new
mv_mbus_dram_info_nooverlap() function, which returns the same
information as mv_mbus_dram_info(), but guaranteed to not overlap with
the I/O windows.
In the end, it gives us two variants of the mv_mbus_dram_info*()
functions:
- The normal one, mv_mbus_dram_info(), which has been around for many
years. This function returns the raw DRAM ranges, which are
guaranteed to use power of two sizes, but will overlap with I/O
windows. This function will therefore be used by all DMA masters
(SATA, XOR, Ethernet, etc.) except the CESA crypto driver.
- The new 'nooverlap' variant, mv_mbus_dram_info_nooverlap(). This
function returns DRAM ranges after they have been "tweaked" to make
sure they don't overlap with I/O windows. By doing this tweaking,
we remove the power of two size guarantee. This variant will be
used by the new CESA crypto driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
| |\| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Merge "mvebu fixes for 4.1 (part 3)" from Gregory CLEMENT:
Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
possible on Armada XP as far as I know)
* tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu:
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
bridge window"
This reverts commit 1737cac69369 ("bus: mvebu-mbus: make sure SDRAM CS
for DMA don't overlap the MBus bridge window"), because it breaks DMA
on platforms having more than 2 GB of RAM.
This commit changed the information reported to DMA masters device
drivers through the mv_mbus_dram_info() function so that the returned
DRAM ranges do not overlap with I/O windows.
This was necessary as a preparation to support the new CESA Crypto
Engine driver, which will use DMA for cryptographic operations. But
since it does DMA with the SRAM which is mapped as an I/O window,
having DRAM ranges overlapping with I/O windows was problematic.
To solve this, the above mentioned commit changed the mvebu-mbus to
adjust the DRAM ranges so that they don't overlap with the I/O
windows. However, by doing this, we re-adjust the DRAM ranges in a way
that makes them have a size that is no longer a power of two. While
this is perfectly fine for the Crypto Engine, which supports DRAM
ranges with a granularity of 64 KB, it breaks basically all other DMA
masters, which expect power of two sizes for the DRAM ranges.
Due to this, if the installed system memory is 4 GB, in two
chip-selects of 2 GB, the second DRAM range will be reduced from 2 GB
to a little bit less than 2 GB to not overlap with the I/O windows, in
a way that results in a DRAM range that doesn't have a power of two
size. This means that whenever you do a DMA transfer with an address
located in the [ 2 GB ; 4 GB ] area, it will freeze the system. Any
serious DMA activity like simply running:
for i in $(seq 1 64) ; do dd if=/dev/urandom of=file$i bs=1M count=16 ; done
in an ext3 partition mounted over a SATA drive will freeze the system.
Since the new CESA crypto driver that uses DMA has not been merged
yet, the easiest fix is to simply revert this commit. A follow-up
commit will introduce a different solution for the CESA crypto driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 1737cac69369 ("bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit a0b5cd4ac2d6 ("bus: mvebu-mbus: use automatic I/O
synchronization barriers") enabled the usage of automatic I/O
synchronization barriers by enabling bit WIN_CTRL_SYNCBARRIER in the
control registers of MBus windows, but on non io-coherent platforms
(orion5x, kirkwood and dove) the WIN_CTRL_SYNCBARRIER bit in
the window control register is either reserved (all windows except 6
and 7) or enables read-only protection (windows 6 and 7).
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Fixes: a0b5cd4ac2d6 ("bus: mvebu-mbus: use automatic I/O synchronization barriers")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
| | |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The MIPS Common Device Memory Map (CDMM) is internal to the core and has
native endianness. There is therefore no need to byte swap the accesses
on big endian targets, so convert the CDMM bus driver to use
__raw_readl() rather than readl().
Fixes: 8286ae03308c ("MIPS: Add CDMM bus support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9904/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently in validate_group(), there is a static initializer
for fake_pmu.used_mask which is based on CPU_BITS_NONE but
the used_mask array size is based on CCI_PMU_MAX_HW_EVENTS.
CCI_PMU_MAX_HW_EVENTS is not based on NR_CPUS, so CPU_BITS_NONE
is not correct and will cause a build failure if NR_CPUS
is set high enough to make CPU_BITS_NONE larger than used_mask.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
| |
The base address for DRA7 CLK1_HOST_CLK1_2 host instance is
0x44800000, so correct offset is 0x800000. DRA7 TRM rev X(fewb 2015)
has updates for this information.
With wrong offset these errors are not correctly cleared by the L3
IRQ handler and cause an continuous interrupt scenario and system lockup.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/drivers
Merge "arm-cci PMU updates for 4.1" from Will Deacon:
CCI-400 PMU updates
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
* tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
