| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|\
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/block/hd.c
drivers/block/mg_disk.c
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| | |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* git://git.infradead.org/mtd-2.6:
mtd: fix timeout in M25P80 driver
mtd: Bug in m25p80.c during whole-chip erase
mtd: expose subpage size via sysfs
mtd: mtd in mtd_release is unused without CONFIG_MTD_CHAR
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Extend erase timeout in M25P80 SPI Flash driver.
The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
MTD has got sysfs support in 2.6.30-rc1. But subpage size is not
exposed there - do this.
UBI utilities badly need this parameter. At the moment there is
no way to get subpage size - ioctls do not return it. And we
just got sysfs support, so we can easilly extend it with this
additional parameter.
This can be merged late in the development cycle because:
1. sysfs support has been just added - there are no users for
it so far, even.
2. UBI utilities really need this parameter, and it is better
not to delay this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
drivers/mtd/mtdcore.c: In function 'mtd_release':
drivers/mtd/mtdcore.c:51: warning: unused variable 'mtd'
[akpm: make it actually build]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
mtd_blkdevs processes requests one-by-one synchronously from a kthread
and can be easily converted to dequeueing model. Convert it.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
end_request() has been kept around for backward compatibility;
however, it's about time for it to go away.
* There aren't too many users left.
* Its use of @updtodate is pretty confusing.
* In some cases, newer code ends up using mixture of end_request() and
[__]blk_end_request[_all](), which is way too confusing.
So, add [__]blk_end_request_cur() and replace end_request() with it.
Most conversions are straightforward. Noteworthy ones are...
* paride/pcd: next_request() updated to take 0/-errno instead of 1/0.
* paride/pf: pf_end_request() and next_request() updated to take
0/-errno instead of 1/0.
* xd: xd_readwrite() updated to return 0/-errno instead of 1/0.
* mtd/mtd_blkdevs: blktrans_discard_request() updated to return
0/-errno instead of 1/0. Unnecessary local variable res
initialization removed from mtd_blktrans_thread().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Laurent Vivier <Laurent@lvivier.info>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: unsik Kim <donari75@gmail.com>
|
|/
|
|
|
|
|
| |
Wrong types on IRQ handler
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| | |
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: add fsync capability
|
| |
| |
| |
| |
| |
| |
| | |
Now, we can call fsync() on an UBI volume.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
|
| | |
| | |
| | |
| | |
| | |
| | | |
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Prevent NUMONYX M29W128G memories from using write buffer,
because it doesn't work properly.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In the existing implementation, ecc_stats fields are incremented only by
one, regardless of master mtd errors number. For example, if there are N
errors were corrected by ECC, partition ecc_stats.corrected will be
incremented by one.
This commit changes simple increment to sum of old value and parent mtd
error count.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern. The TQM8548_BE requires a further short delay
after writing out a buffer. Normally the R/B pin should be checked, but
it's not connected on the TQM8548_BE. The existing driver uses similar
fixed delay points. To manage these extra delays in a more general way,
I introduced the "fsl,ump-wait-flags" property allowing the board-
specific driver to specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | | |
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move the driver model init code out of the "#ifdef CONFIG_PROC_FS"
block.
Tested with both values of CONFIG_PROC_FS . Tested with CONFIG_MTD=m .
Issue was reported here: http://lkml.org/lkml/2009/4/4/107
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | | |
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
1) Add more sysfs attributes: flags, size, erasesize, writesize,
oobsize, numeraseregions, name
2) Move core_initcall() code into init_mtd(). The original approach
does not work if CONFIG_MTD=m .
3) Add device_unregister() in del_mtd_device() so that devices get
removed from sysfs as each driver is unloaded.
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Update driver model support in the MTD framework, so it fits
better into the current udev-based hotplug framework:
- Each mtd_info now has a device node. MTD drivers should set
the dev.parent field to point to the physical device, before
setting up partitions or otherwise declaring MTDs.
- Those device nodes always map to /sys/class/mtdX device nodes,
which no longer depend on MTD_CHARDEV.
- Those mtdX sysfs nodes have a "starter set" of attributes;
it's not yet sufficient to replace /proc/mtd.
- Enabling MTD_CHARDEV provides /sys/class/mtdXro/ nodes and the
/sys/class/mtd*/dev attributes (for udev, mdev, etc).
- Include a MODULE_ALIAS_CHARDEV_MAJOR macro. It'll work with
udev creating the /dev/mtd* nodes, not just a static rootfs.
So the sysfs structure is pretty much what you'd expect, except
that readonly chardev nodes are a bit quirky.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A pointer to plat_nand_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Hamish Moffatt <hamish@cloud.net.au>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A pointer to sa1100_mtd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Now as all PXA Zaurii are converted to use the physmap map,
drop the sharpsl-flash map completely.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
SLOF has a further node which could not be evaluated
by the current routine. The current routine returns
because the node hasn't the required reg property. As
fix this patch adds a check to determine the partition
child nodes. If the node is not a partition the number
of total partitions will be decreased and loop continues
with the next nodes.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add support for direct mapping through mtdconcat, if possible, by attaching the
samebacking_dev_info structure to the master.
It has some restrictions:
(1) It won't permit direct mapping of concatenated devices that have differing
BDIs.
(2) It doesn't support maps that span the 'gap' between devices, although it
possibly could if the devices spanned across return compatible
(ie. contiguous) addresses from their get_unmapped_area() ops.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Present backing device capabilities for MTD character device files to allow
NOMMU mmap to do direct mapping where possible.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
OneNAND write-while-program method of writing improves performance,
compared with ordinary writes, by transferring data to OneNAND's
RAM buffers atthe same time as programming the NAND core.
When writing several NAND pages at a time, an improvement of
12% to 25% is seen.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
panic_write may read in an interrupt context.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently redboot and afx parser return allocated mtd_partition array
and cmdlinepart and ar7 return persistent array.
This patch make cmdlinepart and ar7 also return allocated array, so
that all users can free it regardless of parser type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
- do not leave spin lock locked
- initialise spin lock
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
MTD's have both an index number and a name. Formerly,
the MTD selected for mtdoops was done only by index
number. With this patch, a name can be used instead.
For example, the kernel command line:
console=ttyMTD5
selects MTD 5 for mtdoops. But now this is also possible:
console=ttyMTD,log
which selects the MTD named "log" for mtdoops.
This has the advantage that partitions can be added or
removed that would affect the MTD index number but not the
name, without having to then change the kernel command line.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
OBM/bootloader
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The nftl module is missing the block-major-93-* alias that would cause
it to be auto-loaded when a nftl of that type is opened. This patch
adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The mtdchar module is missing the char-major-90-* alias that would cause
it to be auto-loaded when a device of that type is opened. This patch
adds the alia..
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|