summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
Commit message (Collapse)AuthorAgeFilesLines
...
* bnxt_en: Fix VF mac address regression.Michael Chan2018-09-293-7/+13
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 28ea334bd1657f3c43485b4a8592672fc6835fac ] The recent commit to always forward the VF MAC address to the PF for approval may not work if the PF driver or the firmware is older. This will cause the VF driver to fail during probe: bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF bnxt_en 0000:00:03.0: Unable to initialize mac address. bnxt_en: probe of 0000:00:03.0 failed with error -99 We fix it by treating the error as fatal only if the VF MAC address is locally generated by the VF. Fixes: 707e7e966026 ("bnxt_en: Always forward VF MAC address to the PF.") Reported-by: Seth Forshee <seth.forshee@canonical.com> Reported-by: Siwei Liu <loseweigh@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hp100: fix always-true check for link up stateColin Ian King2018-09-291-1/+1
| | | | | | | | | | | | | | | | [ Upstream commit a7f38002fb69b44f8fc622ecb838665d0b8666af ] The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value that is always non-zero and hence the wait for the link to drop always terminates prematurely. Fix this by using a logical not operator instead of a bitwise complement. This issue has been in the driver since pre-2.6.12-rc2. Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: mvpp2: make sure we use single queue mode on PPv2.1Maxime Chevallier2018-09-261-0/+6
| | | | | | | | | | | | | | | | | [ Upstream commit 1e27a628e3f444f53ab8099dfb31c5156e38d112 ] The PPv2 driver defines 2 "queue_modes" : - QDIST_SINGLE_MODE, where each port share one rx queue vector between all CPUs - QDIST_MULTI_MODE, where each port has one rx queue vector per CPU. Multi queue mode isn't available on PPv2.1, make sure we fallback to single mode when running on this revision. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: gemini: Allow multiple ports to instantiateLinus Walleij2018-09-261-1/+4
| | | | | | | | | | | | | | [ Upstream commit 60cc7767b901dd1e3f70755c3d2505556ba487c2 ] The code was not tested with two ports actually in use at the same time. (I blame this on lack of actual hardware using that feature.) Now after locating a system using both ports, add necessary fix to make both ports come up. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* liquidio: fix hang when re-binding VF host drv after running DPDK VF driverRick Farrington2018-09-262-0/+6
| | | | | | | | | | | | | | | | | | [ Upstream commit ac13d6d8eaded15c67265eafc32f439ea3a0ac4a ] When configuring SLI_PKTn_OUTPUT_CONTROL, VF driver was assuming that IPTR mode was disabled by reset, which was not true. Since DPDK driver had set IPTR mode previously, the VF driver (which uses buf-ptr-only mode) was not properly handling DROQ packets (i.e. it saw zero-length packets). This represented an invalid hardware configuration which the driver could not handle. Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hns3: Fix return value error in hns3_reset_notify_down_enetHuazhong Tan2018-09-261-1/+1
| | | | | | | | | | | | | | | | [ Upstream commit 6b1385cc251ae9f26b720fa5c8c00bf19af336ae ] When doing reset, netdev has not been brought up is not an error, it means that we do not need do the stop operation, so just return zero. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hns3: Fix for reset_level default assignment probelmYunsheng Lin2018-09-261-1/+5
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 82b5321460005ac5d34996e17f5a51a4004a1e14 ] handle->reset_level is assigned to HNAE3_NONE_RESET when client is initialized, if a tx timeout happens right after initialization, then handle->reset_level is not resetted to HNAE3_FUNC_RESET in hclge_reset_event, which will cause reset event not properly handled problem. This patch fixes it by setting handle->reset_level properly when client is initialized. Fixes: 6d4c3981a8d8 ("net: hns3: Changes to make enet watchdog timeout func common for PF/VF") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hns3: Reset net device with rtnl_lockHuazhong Tan2018-09-261-3/+2
| | | | | | | | | | | | | | | [ Upstream commit 6d4fab39533f1bcd933d82d1667ceea93e4de260 ] Since current locking was not covering certain code where netdev was being accessed or manipulated, this patch fixes it. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Add missing SET_DRIVER_VERSION command translationNoa Osherovich2018-09-261-0/+1
| | | | | | | | | | | | | [ Upstream commit 0f4039104ee61e14ac4771a2181c2a20572f4ec9 ] When translating command opcodes to a string, SET_DRIVER_VERSION command was missing. Fixes: 42ca502e179d0 ('net/mlx5_core: Use a macro in mlx5_command_str()') Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nfp: avoid buffer leak when FW communication failsJakub Kicinski2018-09-261-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 07300f774fec9519663a597987a4083225588be4 ] After device is stopped we reset the rings by moving all free buffers to positions [0, cnt - 2], and clear the position cnt - 1 in the ring. We then proceed to clear the read/write pointers. This means that if we try to reset the ring again the code will assume that the next to fill buffer is at position 0 and swap it with cnt - 1. Since we previously cleared position cnt - 1 it will lead to leaking the first buffer and leaving ring in a bad state. This scenario can only happen if FW communication fails, in which case the ring will never be used again, so the fact it's in a bad state will not be noticed. Buffer leak is the only problem. Don't try to move buffers in the ring if the read/write pointers indicate the ring was never used or have already been reset. nfp_net_clear_config_and_disable() is now fully idempotent. Found by code inspection, FW communication failures are very rare, and reconfiguring a live device is not common either, so it's unlikely anyone has ever noticed the leak. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nfp: don't fail probe on pci_sriov_set_totalvfs() errorsJakub Kicinski2018-09-261-8/+12
| | | | | | | | | | | | | | | | [ Upstream commit 5b0ced17edc5710d4e946392d0f2934a9e07b37f ] On machines with buggy ACPI tables or when SR-IOV is already enabled we may not be able to set the SR-IOV VF limit in sysfs, it's not fatal because the limit is imposed by the driver anyway. Only the sysfs 'sriov_totalvfs' attribute will be too high. Print an error to inform user about the failure but allow probe to continue. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* amd-xgbe: use dma_mapping_error to check map errorsYueHaibing2018-09-261-4/+3
| | | | | | | | | | | | | [ Upstream commit b24dbfe9ce03d9f83306616f22fb0e04e8960abe ] The dma_mapping_error() returns true or false, but we want to return -ENOMEM if there was an error. Fixes: 174fd2597b0b ("amd-xgbe: Implement split header receive support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Use u16 for Work Queue buffer fragment sizeTariq Toukan2018-09-262-3/+3
| | | | | | | | | | | | | | | | [ Upstream commit 8d71e818506718e8d7032ce824b5c74a17d4f7a5 ] Minimal stride size is 16. Hence, the number of strides in a fragment (of PAGE_SIZE) is <= PAGE_SIZE / 16 <= 4K. u16 is sufficient to represent this. Fixes: 388ca8be0037 ("IB/mlx5: Implement fragmented completion queue (CQ)") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Fix possible deadlock from lockdep when adding fte to fgRoi Dayan2018-09-261-37/+37
| | | | | | | | | | | | | | [ Upstream commit ad9421e36a77056a4f095d49b9605e80b4d216ed ] This is a false positive report due to incorrect nested lock annotations as we lock multiple fgs with the same subclass. Instead of locking all fgs only lock the one being used as was done before. Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel") Signed-off-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Fix not releasing read lock when adding flow rulesRoi Dayan2018-09-261-0/+2
| | | | | | | | | | | | | | [ Upstream commit 071304772fc747d5df13c51f1cf48a4b922a5e0d ] If building match list fg fails and we never jumped to search_again_locked label then the function returned without unlocking the read lock. Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Fix debugfs cleanup in the device init/remove flowJack Morgenstein2018-09-261-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 5df816e7f43f1297c40021ef17ec6e722b45c82f ] When initializing the device (procedure init_one), the driver calls mlx5_pci_init to perform pci initialization. As part of this initialization, mlx5_pci_init creates a debugfs directory. If this creation fails, init_one aborts, returning failure to the caller (which is the probe method caller). The main reason for such a failure to occur is if the debugfs directory already exists. This can happen if the last time mlx5_pci_close was called, debugfs_remove (silently) failed due to the debugfs directory not being empty. Guarantee that such a debugfs_remove failure will not occur by instead calling debugfs_remove_recursive in procedure mlx5_pci_close. Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware and software flows") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Check for error in mlx5_attach_interfaceHuy Nguyen2018-09-261-5/+10
| | | | | | | | | | | | | | [ Upstream commit 47bc94b82291e007da61ee1b3d18c77871f3e158 ] Currently, mlx5_attach_interface does not check for error after calling intf->attach or intf->add. When these two calls fails, the client is not initialized and will cause issues such as kernel panic on invalid address in the teardown path (mlx5_detach_interface) Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: E-Switch, Fix memory leak when creating switchdev mode FDB tablesRaed Salem2018-09-261-0/+1
| | | | | | | | | | | | | [ Upstream commit c88a026e01219488e745f4f0267fd76c2bb68421 ] The memory allocated for the slow path table flow group input structure was not freed upon successful return, fix that. Fixes: 1967ce6ea5c8 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode") Signed-off-by: Raed Salem <raeds@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: qca_spi: Fix race condition in spi transfersStefan Wahren2018-09-263-98/+93
| | | | | | | | | | | | | | | | | | [ Upstream commit e65a9e480e91ddf9e15155454d370cead64689c8 ] With performance optimization the spi transfer and messages of basic register operations like qcaspi_read_register moved into the private driver structure. But they weren't protected against mutual access (e.g. between driver kthread and ethtool). So dumping the QCA7000 registers via ethtool during network traffic could make spi_sync hang forever, because the completion in spi_message is overwritten. So revert the optimization completely. Fixes: 291ab06ecf676 ("net: qualcomm: new Ethernet over SPI driver for QCA700") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Fix use-after-free in self-healing flowJack Morgenstein2018-09-262-4/+12
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 76d5581c870454be5f1f1a106c57985902e7ea20 ] When the mlx5 health mechanism detects a problem while the driver is in the middle of init_one or remove_one, the driver needs to prevent the health mechanism from scheduling future work; if future work is scheduled, there is a problem with use-after-free: the system WQ tries to run the work item (which has been freed) at the scheduled future time. Prevent this by disabling work item scheduling in the health mechanism when the driver is in the middle of init_one() or remove_one(). Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* be2net: Fix memory leak in be_cmd_get_profile_config()Petr Oros2018-09-261-1/+1
| | | | | | | | | | | | [ Upstream commit 9d7f19dc4673fbafebfcbf30eb90e09fa7d1c037 ] DMA allocated memory is lost in be_cmd_get_profile_config() when we call it with non-NULL port_res parameter. Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: mvneta: fix mtu change on port without linkYelena Krivosheev2018-09-191-1/+0
| | | | | | | | | | | | | | | | | [ Upstream commit 8466baf788ec3e18836bd9c91ba0b1a07af25878 ] It is incorrect to enable TX/RX queues (call by mvneta_port_up()) for port without link. Indeed MTU change for interface without link causes TX queues to stuck. Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Yelena Krivosheev <yelena@marvell.com> [gregory.clement: adding Fixes tags and rewording commit log] Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hns3: Fix for phy link issue when using marvell phy driverJian Shen2018-09-151-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 60081dcc4fce385ade26d3145b2479789df0b7e5 ] For marvell phy m88e1510, bit SUPPORTED_FIBRE of phydev->supported is default on. Both phy_resume() and phy_suspend() will check the SUPPORTED_FIBRE bit and write register of fibre page. Currently in hns3 driver, the SUPPORTED_FIBRE bit will be cleared after phy_connect_direct() finished. Because phy_resume() is called in phy_connect_direct(), and phy_suspend() is called when disconnect phy device, so the operation for fibre page register is not symmetrical. It will cause phy link issue when reload hns3 driver. This patch fixes it by disable the SUPPORTED_FIBRE before connecting phy. Fixes: 256727da7395 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zeroXi Wang2018-09-151-1/+1
| | | | | | | | | | | | | | | | | | | [ Upstream commit 6c39d5278e62956238a681e4cfc69fae5507fc57 ] According to the functional specification of hardware, the first descriptor of response from command 'lookup vlan talbe' is not valid. Currently, the first descriptor is parsed as normal value, which will cause an expected error. This patch fixes this problem by skipping the first descriptor. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridgeIdo Schimmel2018-09-153-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 602b74eda81311dbdb5dbab08c30f789f648ebdc ] When a bridge device is removed, the VLANs are flushed from each configured port. This causes the ports to decrement the reference count on the associated FIDs (filtering identifier). If the reference count of a FID is 1 and it has a RIF (router interface), then this RIF is destroyed. However, if no port is member in the VLAN for which a RIF exists, then the RIF will continue to exist after the removal of the bridge. To reproduce: # ip link add name br0 type bridge vlan_filtering 1 # ip link set dev swp1 master br0 # ip link add link br0 name br0.10 type vlan id 10 # ip address add 192.0.2.0/24 dev br0.10 # ip link del dev br0 The RIF associated with br0.10 continues to exist. Fix this by iterating over all the bridge device uppers when it is destroyed and take care of destroying their RIFs. Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nfp: wait for posted reconfigs when disabling the deviceJakub Kicinski2018-09-151-15/+33
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9ad716b95fd6c6be46a4f2d5936e514b5bcd744d ] To avoid leaking a running timer we need to wait for the posted reconfigs after netdev is unregistered. In common case the process of deinitializing the device will perform synchronous reconfigs which wait for posted requests, but especially with VXLAN ports being actively added and removed there can be a race condition leaving a timer running after adapter structure is freed leading to a crash. Add an explicit flush after deregistering and for a good measure a warning to check if timer is running just before structures are freed. Fixes: 3d780b926a12 ("nfp: add async reconfiguration mechanism") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "net: stmmac: Do not keep rearming the coalesce timer in stmmac_xmit"Jerome Brunet2018-09-152-5/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e5133f2f1261f8ab412e7fc5e3694c9f84328f89 ] This reverts commit 4ae0169fd1b3c792b66be58995b7e6b629919ecf. This change in the handling of the coalesce timer is causing regression on (at least) amlogic platforms. Network will break down very quickly (a few seconds) after starting a download. This can easily be reproduced using iperf3 for example. The problem has been reported on the S805, S905, S912 and A113 SoCs (Realtek and Micrel PHYs) and it is likely impacting all Amlogics platforms using Gbit ethernet No problem was seen with the platform using 10/100 only PHYs (GXL internal) Reverting change brings things back to normal and allows to use network again until we better understand the problem with the coalesce timer. Cc: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Vitor Soares <soares@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devicesAzat Khuzhin2018-09-151-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 05212ba8132b42047ab5d63d759c6f9c28e7eab5 ] I have two Ethernet adapters: r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18 r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30 And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to receive any packets. tcpdump shows a lot of checksum mismatch. [1]: a0f79386a4968b4925da6db2d1daffd0605a4402 [2]: 0519359784328bfa92bf0931bf0cff3b58c16932 (4.19 merge window opened) I started bisecting and the found that [3] breaks it. According to [4]: "For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig needs to be set after the tx/rx is enabled." So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works (RTL8168e works too). [3]: 3559d81e76bfe3803e89f2e04cf6ef7ab4f3aace [4]: e542a2269f232d61270ceddd42b73a4348dee2bb ("r8169: adjust the RxConfig settings.") Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing with it already. Fixes: 3559d81e76bfe3803e89f2e04cf6ef7ab4f3aace ("r8169: simplify rtl_hw_start_8169") Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: Realtek linux nic maintainers <nic_swsd@realtek.com> Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net/mlx5: Fix SQ offset in QPs with small RQTariq Toukan2018-09-151-2/+3
| | | | | | | | | | | | | | | | | | | [ Upstream commit 639505d4397b8c654a8e2616f9cb70ece40c83f9 ] Correct the formula for calculating the RQ page remainder, which should be in byte granularity. The result will be non-zero only for RQs smaller than PAGE_SIZE, as an RQ size is a power of 2. Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the SQ offset in strides granularity. Fixes: d7037ad73daa ("net/mlx5: Fix QP fragmented buffer allocation") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: macb: Fix regression breaking non-MDIO fixed-link PHYsAhmad Fatoum2018-09-151-10/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit ab5f11055fdf8dfc3ddbd89e8e3cc550de41d1d3 ] commit 739de9a1563a ("net: macb: Reorganize macb_mii bringup") broke initializing macb on the EVB-KSZ9477 eval board. There, of_mdiobus_register was called even for the fixed-link representing the RGMII-link to the switch with the result that the driver attempts to enumerate PHYs on a non-existent MDIO bus: libphy: MACB_mii_bus: probed mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0 [snip] mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31 The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO, and calling of_phy_register_fixed_link later on fails because it tries to claim the same GPIO: macb f0028000.ethernet: broken fixed-link specification Fix this by registering the fixed-link before calling mdiobus_register. Fixes: 739de9a1563a ("net: macb: Reorganize macb_mii bringup") Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* bnxt_en: Do not adjust max_cp_rings by the ones used by RDMA.Michael Chan2018-09-154-12/+9
| | | | | | | | | | | | | | | | | | | [ Upstream commit 00fe9c326d2027f2437dea38ef0e82f9d02d94c0 ] Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number of MSIX vectors used by RDMA. There is one code path in open that needs to check the true max_cp_rings including any used by RDMA. This code is now checking for the reduced max_cp_rings which will fail when the number of cp rings is very small. To fix this in a clean way, we don't adjust max_cp_rings anymore. Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the reduced max_cp_rings when appropriate. Fixes: ec86f14ea506 ("bnxt_en: Add ULP calls to stop and restart IRQs.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* bnxt_en: Clean up unused functions.Michael Chan2018-09-154-18/+1
| | | | | | | | | | | [ Upstream commit ad95c27bdb930105f3eea02621bda157caf2862d ] Remove unused bnxt_subtract_ulp_resources(). Change bnxt_get_max_func_irqs() to static since it is only locally used. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* r8169: add support for NCube 8168 network cardAnthony Wong2018-09-151-0/+1
| | | | | | | | | | | | | | | [ Upstream commit 9fd0e09a4e86499639653243edfcb417a05c5c46 ] This card identifies itself as: Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06) Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468] Adding a new entry to rtl8169_pci_tbl makes the card work. Link: http://launchpad.net/bugs/1788730 Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qlge: Fix netdev features configuration.Manish Chopra2018-09-151-15/+8
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 6750c87074c5b534d82fdaabb1deb45b8f1f57de ] qlge_fix_features() is not supposed to modify hardware or driver state, rather it is supposed to only fix requested fetures bits. Currently qlge_fix_features() also goes for interface down and up unnecessarily if there is not even any change in features set. This patch changes/fixes following - 1) Move reload of interface or device re-config from qlge_fix_features() to qlge_set_features(). 2) Reload of interface in qlge_set_features() only if relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed. 3) Get rid of qlge_fix_features() since driver is not really required to fix any features bit. Signed-off-by: Manish <manish.chopra@cavium.com> Reviewed-by: Benjamin Poirier <bpoirier@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: macb: do not disable MDIO bus at open/close timeAnssi Hannula2018-09-151-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 0da70f808029476001109b6cb076737bc04cea2e ] macb_reset_hw() is called from macb_close() and indirectly from macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE (Management Port Enable) bit. This will prevent accessing any other PHYs for other Ethernet MACs on the MDIO bus, which remains registered at macb_reset_hw() time, until macb_init_hw() is called from macb_open() which sets the MPE bit again. I.e. currently the MDIO bus has a short disruption at open time and is disabled at close time until the interface is opened again. Fix that by only touching the RE and TE bits when enabling and disabling RX/TX. v2: Make macb_init_hw() NCR write a single statement. Fixes: 6c36a7074436 ("macb: Use generic PHY layer") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: bcmgenet: use MAC link status for fixed phyDoug Berger2018-09-152-2/+11
| | | | | | | | | | | | | | | | [ Upstream commit c3c397c1f16c51601a3fac4fe0c63ad8aa85a904 ] When using the fixed PHY with GENET (e.g. MOCA) the PHY link status can be determined from the internal link status captured by the MAC. This allows the PHY state machine to use the correct link state with the fixed PHY even if MAC link event interrupts are missed when the net device is opened. Fixes: 8d88c6ebb34c ("net: bcmgenet: enable MoCA link state change detection") Signed-off-by: Doug Berger <opendmb@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: mvneta: fix mvneta_config_rss on armada 3700Jisheng Zhang2018-08-221-11/+20
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 0f5c6c30a0f8c629b92ecdaef61b315c43fde10a ] The mvneta Ethernet driver is used on a few different Marvell SoCs. Some SoCs have per cpu interrupts for Ethernet events, the driver uses a per CPU napi structure for this case. Some SoCs such as armada 3700 have a single interrupt for Ethernet events, the driver uses a global napi structure for this case. Current mvneta_config_rss() always operates the per cpu napi structure. Fix it by operating a global napi for "single interrupt" case, and per cpu napi structure for remaining cases. Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: ethernet: mvneta: Fix napi structure mixup on armada 3700Andrew Lunn2018-08-221-10/+12
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 7a86f05faf112463cfbbdfd222012e247de461a1 ] The mvneta Ethernet driver is used on a few different Marvell SoCs. Some SoCs have per cpu interrupts for Ethernet events. Some SoCs have a single interrupt, independent of the CPU. The driver handles this by having a per CPU napi structure when there are per CPU interrupts, and a global napi structure when there is a single interrupt. When the napi core calls mvneta_poll(), it passes the napi instance. This was not being propagated through the call chain, and instead the per-cpu napi instance was passed to napi_gro_receive() call. This breaks when there is a single global napi instance. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC") Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* r8169: don't use MSI-X on RTL8106eJian-Hong Pan2018-08-221-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 7bb05b85bc2d1a1b647b91424b2ed4a18e6ecd81 ] Found the ethernet network on ASUS X441UAR doesn't come back on resume from suspend when using MSI-X. The chip is RTL8106e - version 39. [ 21.848357] libphy: r8169: probed [ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID 44900000, IRQ 127 [ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0 [ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE) [ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full - flow control off [ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE) Here is the ethernet controller in detail: 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136] (rev 07) Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast Ethernet controller [1043:200f] Flags: bus master, fast devsel, latency 0, IRQ 16 I/O ports at e000 [size=256] Memory at ef100000 (64-bit, non-prefetchable) [size=4K] Memory at e0000000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 Falling back to MSI fixes the issue. Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* r8169: don't use MSI-X on RTL8168gHeiner Kallweit2018-08-221-0/+5
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 7c53a722459c1d6ffb0f5b2058c06ca8980b8600 ] There have been two reports that network doesn't come back on resume from suspend when using MSI-X. Both cases affect the same chip version (RTL8168g - version 40), on different systems. Falling back to MSI fixes the issue. Even though we don't really have a proof yet that the network chip version is to blame, let's disable MSI-X for this version. Reported-by: Steve Dodd <steved424@gmail.com> Reported-by: Lou Reed <gogen@disroot.org> Tested-by: Steve Dodd <steved424@gmail.com> Tested-by: Lou Reed <gogen@disroot.org> Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: ethernet: ti: cpsw: fix runtime_pm while add/kill vlanIvan Khoronzhuk2018-08-111-4/+7
| | | | | | | | | It's exclusive with normal behaviour but if try to set vlan to one of the reserved values is made, the cpsw runtime pm is broken. Fixes: a6c5d14f5136 ("drivers: net: cpsw: ndev: fix accessing to suspended device") Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: ti: cpsw: clear all entries when delete vidIvan Khoronzhuk2018-08-112-11/+5
| | | | | | | | | | | In cases if some of the entries were not found in forwarding table while killing vlan, the rest not needed entries still left in the table. No need to stop, as entry was deleted anyway. So fix this by returning error only after all was cleaned. To implement this, return -ENOENT in cpsw_ale_del_mcast() as it's supposed to be. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Fix IFF_ALLMULTI flag functionalityDmitry Bogdanov2018-08-081-1/+1
| | | | | | | | | | | | | | It was noticed that NIC always pass all multicast traffic to the host regardless of IFF_ALLMULTI flag on the interface. The rule in MC Filter Table in NIC, that is configured to accept any multicast packets, is turning on if IFF_MULTICAST flag is set on the interface. It leads to passing all multicast traffic to the host. This fix changes the condition to turn on that rule by checking IFF_ALLMULTI flag as it should. Fixes: b21f502f84be ("net:ethernet:aquantia: Fix for multicast filter handling.") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx5e: Cleanup of dcbnl related fieldsHuy Nguyen2018-08-082-21/+11
| | | | | | | | | | | | | Remove unused netdev_registered_init/remove in en.h Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails. Remove extra white space Fixes: 2a5e7a1344f4 ("net/mlx5e: Add dcbnl dscp to priority support") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Cc: Yuval Shaia <yuval.shaia@oracle.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx5e: Properly check if hairpin is possible between two functionsOr Gerlitz2018-08-081-4/+4
| | | | | | | | | | | | | The current check relies on function BDF addresses and can get us wrong e.g when two VFs are assigned into a VM and the PCI v-address is set by the hypervisor. Fixes: 5c65c564c962 ('net/mlx5e: Support offloading TC NIC hairpin flows') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Alaa Hleihel <alaa@mellanox.com> Tested-by: Alaa Hleihel <alaa@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: thunderx: check for failed allocation lmac->dmacsColin Ian King2018-08-071-0/+2
| | | | | | | | | The allocation of lmac->dmacs is not being checked for allocation failure. Add the check. Fixes: 3a34ecfd9d3f ("net: thunderx: add MAC address filter tracking for LMAC") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* cxgb4: mk_act_open_req() buggers ->{local, peer}_ip on big-endian hostsAl Viro2018-08-071-4/+2
| | | | | | | | | | | | | | Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match() sets fs.val.{l,f}ip to net-endian values without conversion - they come straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp. So the assignment in mk_act_open_req() ought to be a straight copy. As far as I know, T4 PCIe cards do exist, so it's not as if that thing could only be found on little-endian systems... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core_acl_flex_actions: Remove redundant mirror resource destructionNir Dotan2018-08-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate resource detruction scenario. For mirror actions, such duplicate destruction leads to a crash as in: # tc qdisc add dev swp49 ingress # tc filter add dev swp49 parent ffff: \ protocol ip chain 100 pref 10 \ flower skip_sw dst_ip 192.168.101.1 action drop # tc filter add dev swp49 parent ffff: \ protocol ip pref 10 \ flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \ action mirred egress mirror dev swp4 Therefore add a call to mlxsw_afa_resource_del() in mlxsw_afa_mirror_destroy() in order to clear that resource from rule's resources. Fixes: d0d13c1858a1 ("mlxsw: spectrum_acl: Add support for mirror action") Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core_acl_flex_actions: Remove redundant counter destructionNir Dotan2018-08-031-0/+1
| | | | | | | | | | | | | | | Each tc flower rule uses a hidden count action. As counter resource may not be available due to limited HW resources, update _counter_create() and _counter_destroy() pair to follow previously introduced symmetric error condition handling, add a call to mlxsw_afa_resource_del() as part of the counter resource destruction. Fixes: c18c1e186ba8 ("mlxsw: core: Make counter index allocated inside the action append") Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core_acl_flex_actions: Remove redundant resource destructionNir Dotan2018-08-031-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some ACL actions require the allocation of a separate resource prior to applying the action itself. When facing an error condition during the setup phase of the action, resource should be destroyed. For such actions the destruction was done twice which is dangerous and lead to a potential crash. The destruction took place first upon error on action setup phase and then as the rule was destroyed. The following sequence generated a crash: # tc qdisc add dev swp49 ingress # tc filter add dev swp49 parent ffff: \ protocol ip chain 100 pref 10 \ flower skip_sw dst_ip 192.168.101.1 action drop # tc filter add dev swp49 parent ffff: \ protocol ip pref 10 \ flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \ action mirred egress mirror dev swp4 Therefore add mlxsw_afa_resource_del() as a complement of mlxsw_afa_resource_add() to add symmetry to resource_list membership handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the _fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a NOP. Fixes: 140ce421217e ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list") Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-04 22:37:49 +0000